My phone hit the bootloop and was repaired. I have noticed that since then (have had it back for over a week) that the battery % changes up and down. For example it would say 59% then jump down to 42% or jump up to 75% while sitting. I have two batteries (one is just shy of 2 yrs and other is 16 mo) and both have problem. Any tips/suggestions/ideas as to why it does this now?
Better drain your battery to 0, do the pull and charge. Starts with the newer one and see where it brings you.
Remains the same.. ... Might be time for a new phone
Have you tried factory reset or even flash syitable firmware? I know it's painful, but sometime ot's unavoidable. And check your battery health using hidden code first.
It was reset after motherboard replacement (phone hit the dreaded bootloop). How do I check battery health? TY
Related
I've bought a new legit/official (has holo, serials etc.) Atrix battery.
Charged it to 100%.
During usage, its draining literally 10% an hour with very light usage (several minutes an hour). In short its draining at three times the speed of my 1 year old battery.
I've tried wiping battery stats but that didn't work.
Any ideas, or is the stats just buggered and I just gotta run it in? (ie it will go to zero then sit on zero for 5-6 hours lol)
note I've gone back to my original battery in meantime rofl
EDIT: The actual problem is that the batt is reporting much less capacity than it actually has
|The new battery is great capacity wise lasts till midnight
However the stats are still totally screwed, it will say 1% by midday, then hum along until midnight fixed at 1% (I dunno exactly how long for as I can't take the risk of leaving it off at night then its dead and I don't wake up for work in morning). |
Could just be a bad battery. Considering the old works fine that's probably the problem.
wintermute000 said:
I've bought a new legit/official (has holo, serials etc.) Atrix battery.
Charged it to 100%.
During usage, its draining literally 10% an hour with very light usage (several minutes an hour). In short its draining at three times the speed of my 1 year old battery.
I've tried wiping battery stats but that didn't work.
Any ideas, or is the stats just buggered and I just gotta run it in? (ie it will go to zero then sit on zero for 5-6 hours lol)
note I've gone back to my original battery in meantime rofl
Click to expand...
Click to collapse
wintermute000 said:
I've bought a new legit/official (has holo, serials etc.) Atrix battery.
Charged it to 100%.
During usage, its draining literally 10% an hour with very light usage (several minutes an hour). In short its draining at three times the speed of my 1 year old battery.
I've tried wiping battery stats but that didn't work.
Any ideas, or is the stats just buggered and I just gotta run it in? (ie it will go to zero then sit on zero for 5-6 hours lol)
note I've gone back to my original battery in meantime rofl
Click to expand...
Click to collapse
I have a similar problem with the original battery that came with phone it drains the charge quickly to 1% and on one 1% it gives a battery life of more time than the time it took to discharge from 100%.i was thinking of buying a new battery but now i am confused that what should i look before buying the battery to get a battery that can show me the exact charge on the indicator.
I have tried all tutorial of calibration used different roms and kernels but nothing seems to solve the issue.
well I might try that then, just let it run to zero see how long it lasts then see whether the stats come good over time
OK help needed.
The new battery is great capacity wise, lasts from morning to bedtime with >2 hours of bluetooth music, 30 mins calls, a ton of texts.
However the stats are still totally screwed, it will say 1% by midday, then hum along until midnight fixed at 1% (I dunno exactly how long for as I can't take the risk of leaving it off at night then its dead and I don't wake up for work in morning).
Aside from wiping stats which I have tried, is there anythnig else I can do?
I really want to use it, like I said real life capacity is great, but if its always giong to be reporting 1% its a bit dicey not knowing how much batt you really have left...
same issue with my spare battery not sure wtf is going on
When I have battery stat problems the following has always fixed it:
1) leave phone on until it dies
2) take back off phone and plug into wall charger
3) after batt symbol shows 100% (without unplugging or turning off the phone) remove the battery. After a minute or so battery symbol will have question mark
4) put battery back in and leave it for at least 2 hours (seems like I have had to press the switch sometimes but you don't want the phone to reboot or you will have to start all over)
5) reboot into CWM and wipe the battery stats
6) reboot and it should be good to go
Anyone else found a fix to this yet?
I'm now running ICS (turl build) issue is still there.
Steps taken to resolve
- discharge to zero
- charge to max
- wipe stats
still there.
The weird thing is that the actual capacity is fine, it can last all day no worries, just from midday onwards it thinks its 1% so has annoying LED flashing at you, also you have no idea how much batt it actually has.
Edit: I just realised your suggestion above has extra step (take batt out of connected atrix then insert again). I guess I'll have to drain it again and do it overnight... gah
wintermute000 said:
Anyone else found a fix to this yet?
I'm now running ICS (turl build) issue is still there.
Steps taken to resolve
- discharge to zero
- charge to max
- wipe stats
still there.
The weird thing is that the actual capacity is fine, it can last all day no worries, just from midday onwards it thinks its 1% so has annoying LED flashing at you, also you have no idea how much batt it actually has.
Edit: I just realised your suggestion above has extra step (take batt out of connected atrix then insert again). I guess I'll have to drain it again and do it overnight... gah
Click to expand...
Click to collapse
Nothing will work i have tried almost every tutorial. Recently i found out the phone is showing the the full capacity of battery only 500 that's why i think we will have to change that with the actual voltage to get a accurate battery indicator.What's ur battery full charge design check if from the root exploler
/sys/devices/platform/cpap_battery/power_supply/battery
My phone uevent is showing this
Powersupply-capacity=5
Powersupply-voltage-now=3836000
Powersupply-temp=260
Powersupply-charge-fill-design=500
Powersupply-charge-counter=1
terminator1983 said:
Nothing will work i have tried almost every tutorial. Recently i found out the phone is showing the the full capacity of battery only 500 that's why i think we will have to change that with the actual voltage to get a accurate battery indicator.What's ur battery full charge design check if from the root exploler
/sys/devices/platform/cpap_battery/power_supply/battery
My phone uevent is showing this
Powersupply-capacity=5
Powersupply-voltage-now=3836000
Powersupply-temp=260
Powersupply-charge-fill-design=500
Powersupply-charge-counter=1
Click to expand...
Click to collapse
I'll try the insert empty bat into already connected phone, charge to 100% remaining off, repeat trick overnight, then report back.
FWIW on my 'good' battery which is 1 year old ROFL it says 1880
not sure how changing it would help though or is even possible?. It must be dynamically reported somehow as my good battery gives me a 'good' stat.
I use battery calibration and it worked, have it
http://bit.ly/Ah732P
I'm guapurrin
the battery is charging calibration if you have to load it to calibrate
wintermute000 said:
FWIW on my 'good' battery which is 1 year old ROFL it says 1880
not sure how changing it would help though or is even possible?. It must be dynamically reported somehow as my good battery gives me a 'good' stat.
Click to expand...
Click to collapse
How much is ur other battery showing.I have tried different ways but was not able to change values.
500 same as you! second drain and calibrate did nothing
Maybe theres a faulty batch of batteries and we both got one
Can people PLEASE stop telling us to calibrate we've BOTH DONE THAT MANY TIMES NOW. The problem is that the capacity of the battery is being reported as 500mah not 1930 or whatever its supposed to be. THe actual running time of the battery is fantastic, just thinks its at 0 all the time lol
/sys/devices/platform/cpap_battery/power_supply/battery
Powersupply-charge-fill-design=500 - should be ~1900mah
Sent from my Sony Tablet S using Tapatalk
6 months with sk17i...
6 months with pain in (_!_) about battery indicator...
let me describe situation for those who have no such problem:
battery indicator lives with its own life after 30%... mainly in good days it drops from 20% to 1% but in general picture is not so smooth... I have some days when 45% becomes 1% and so on...
Trying to figure out source of the problem I've started to wipe battery status (any calibration software with root or CWM recovery option), but no luck... (yes, I should mentioned that I've also produce full reset of battery status with 100% charge in offline, then removing for 5-10 mins and charge rest of %) and that is definitly - not working... After full discharge without reboot or power off it is not 100% possibility that next discharge goes smooth from 100% to 1% it could breaks again on 15% or 20% or even on 40%.
I was thinking that problem in battery itself and also change it with new one but picture still the same.
According voltage values regular battery with ~1200 for "mini pro" should show from 4.1 to 3.5 values and it does! but battery indicator shows something else...
So question to community: do we have epic persone who can solve that problem?
P.S. as you can see bootloader is unlocked so no worranty availiable... only hope for community.
Batterystats file does not include battery information, it's about the battery usage info and that file is created again every time, that you fully charge battery.
My friend had this strange situation like your's, He had neo.
He visited service center & solved the problem.
I recommed you take it to the service center.
I have a extended battery. I usually get 2 days use on a charge. about a week ago I cannot make it thru a day. The battery is only about 6 weeks old. I tried another battery and same thing. I use task killer and app cleaner and have restarted several times. When I look in battery usage is shows the Android OS using 24% Display 26% and phone idle 24%. I did update all my app and this seemed to help just a little. Anyone have any suggestions before I return my extended battery or do a factory reset. tks in advance.
have you tried draining the phone completely till it shuts off, then plugging it in and letting it charge to 100% with the phone powered down?
Battery instructions say NOT to every let battery drain to 0. So not sure I should try that.
cdenloe said:
Battery instructions say NOT to every let battery drain to 0. So not sure I should try that.
Click to expand...
Click to collapse
That is about the life that I get on mine on a bad day. Now that you have had the phone for a while, more than likely, your battery has not changed but you have installed more apps which are draining you battery even faster. You shouldn't use task killers either, they screw with the roms built in memory management. However, if you must, then use "Task Manager" the built in stock task manager to end apps. Also i agree that you should completely discharge your battery and then let it recharge completely without turning it on and without using it.
PS: You have a nice avatar. Conservative til i die
cdenloe said:
Battery instructions say NOT to every let battery drain to 0. So not sure I should try that.
Click to expand...
Click to collapse
This is not true. The phone has its own power management. When you reach 0%, the battery has still at least 3100mV (on mine it's more than 3200mV).
Li-On and Li-Pol batteries are designed to operate between 4300 and 3000 mV when they reach more or less, than they are damaging.
So you can charge and discharge your phone everyday between 100 and 0%, without any battery damage.
Other thing is Android power management, every time you wipe battery stats or restore backup, or you spend some time in recovery, Android doesn't know, how much capacity is remaining and you need to make more charging cycles, to teach it again and get full capacity from battery. I still don't understand this kind of management in Android.
I've tried all the battery stuff. No dice still discharging fairly quick. In the Battery Usage section It still showing Android OS using around 39 to 40% usage all the time. I have done a full factory reset on the phone 2 days ago and still same.
I noticed, you are using the task killer, stop using it, you have probably loop of killing and starting of some services. Task killer kills, android starts, again and again...
I have uninstalled task killer restarted the phone and still got the high Android OS usage showing.
You won't notice any difference immediately, make one discharge, charge and discharge cycle and you'll see.
Do NOT discharge the battery completely. Over discharging Lithium ion batteries can be harmful to them. Here's a great article going into probably a little too much detail but it gets the point across: http://batteryuniversity.com/learn/article/charging_lithium_ion_batteries
As far as your problem goes it may be an issue with the phone itself I've seen a couple photons that needed to be exchanged due to issues that sound similar to yours. If it's doing the same thing on a different battery I'd take your phone into a sprint repair center, you could also try a factory reset if you have not already done so. If your only seeing this behavior with your current battery then I would return it or request a warranty replacement.
I have a extended battery. I usually get 2 days use on a charge. about a week ago I cannot make it thru a day. The battery is only about 6 weeks old. I tried another battery and same thing. I use task killer and app cleaner and have restarted several times. When I look in battery usage is shows the Android OS using 24% Display 26% and phone idle 24%. I did update all my app and this seemed to help just a little. Anyone have any suggestions before I return my extended battery or do a factory reset. tks in advance.
Click to expand...
Click to collapse
root your photon (if not already rooted) and download battery calibration from market, also after rooting go to android development and download th3bill's extended battery mod
schale01 said:
Do NOT discharge the battery completely. Over discharging Lithium ion batteries can be harmful to them. Here's a great article going into probably a little too much detail but it gets the point across: http://batteryuniversity.com/learn/article/charging_lithium_ion_batteries
Click to expand...
Click to collapse
Omg... Read that article again, and check, how much voltage is in the phone battery, when it reaches 0% ;-)
peetr_ said:
Omg... Read that article again, and check, how much voltage is in the phone battery, when it reaches 0% ;-)
Click to expand...
Click to collapse
Yes, there is an additional reserve that the Smart chip will protect by turning off the battery once it reaches the "0% mark". The Smart chip will also continue to drain the battery further past the 0% mark eating into this battery reserve. Now one full discharge like this probably would not hurt the battery as long as the battery is recharge within a reasonable amount of time. However it certainly does nothing to benefit the battery health whatsoever and it is never recommended to let a battery fully discharge. There are some practices of only charging the battery to 75%-80% that can improve battery life, but individual run time will be sacrificed. My recommendation is if the battery is under 65% than to charge the battery if it is possible to do so.
After doing a factory reset the same problem remained. Sprint exchanged the phone for a new photon. Put my extended battery back in and so far no problems at all with the exception of not being able to join my contacts with my FB contacts.
I have been discharging my Photon and previous phones to 0-5% at least 3 times for a week and did not find any difference in capacity, compared with the new battery. Lasts from the morning to the evening. If I should charge it on 65%, then the phone would be unusable for me.
Like Schale said it could be an actual phone issue, but i highly doubt it. I would try some things before assuming its a problem with your phone. Do this... Also this assumes you are unlocked or at least rooted.
1: Factory reset so to start fresh with no crap applications (task killer apps do more harm than good, as do most battery saver apps)
2: Drain battery till the phone shuts itself off (Dude what right about it reserving a certain amount of juice to not cause damage)
3: Charge to 100% (Dont use the phone during this time.)
4: Use a battery calibrator app (rooted) or recovery (unlocked) to wipe the battery stats.
5: Drain power as fast as possible till phone shuts off
6: Charge to 100% (Again, dont use the phone during this time.)
You can now use the phone how you normally would. If you don't notice a drastic increase in battery after discharging and recharging three or four times over the next few days, I would be comfortable in assuming it's a phone problem. Good luck!
I have an att galaxy s3 (d2att) that I got back in March 2013. Over the course of the year I have probably changed my rom about 20-30 times to get the perfect rom. Now my phone's screen time is about 1 hour while just letting it sit with the display on and not running any apps or touching it. Currently running the task650 rom with android 4.4.3. Wiping the battery stats file or running the calibration app does not work. There is no option in my recovery menu under advanced settings to wipe battery stats and a battery calibration app says the battery file does not exist. Sometimes the phone will turn off at about 30% and the reason I believe for that is that the voltage goes down so much. On time I checked it around 35-40% and it was at about 2.5V and then it shut down. When I charge it, it hovers around 3.9-4.3V but when I use it, it starts to go down like crazy. I don't know if I need a new battery or if I should completely factory reset my phone.
Any advice?
mehtam said:
I have an att galaxy s3 (d2att) that I got back in March 2013. Over the course of the year I have probably changed my rom about 20-30 times to get the perfect rom. Now my phone's screen time is about 1 hour while just letting it sit with the display on and not running any apps or touching it. Currently running the task650 rom with android 4.4.3. Wiping the battery stats file or running the calibration app does not work. There is no option in my recovery menu under advanced settings to wipe battery stats and a battery calibration app says the battery file does not exist. Sometimes the phone will turn off at about 30% and the reason I believe for that is that the voltage goes down so much. On time I checked it around 35-40% and it was at about 2.5V and then it shut down. When I charge it, it hovers around 3.9-4.3V but when I use it, it starts to go down like crazy. I don't know if I need a new battery or if I should completely factory reset my phone.
Any advice?
Click to expand...
Click to collapse
A bad battery can be really dangerous. It may have become like this because of bad use or overuse. I would recommend changing it asap
Sent from my SDT-737 using XDA Free mobile app
I don't see how flashing many ROMs could cause your battery life to drop. However the following issues are possible:
1) The ROM you are using has a bug that is causing some type of battery drain. These do happen.
2) You have charged and discharged your battery so many times that it cannot hold a charge anymore. I start noticing battery life decreasing after about 2 years of my usage (generally fairly low). Most times my battery life does not drop below 60% or so. If you very often let it drop very low, I can see the battery life decrease significantly after about a year.
nhakobian said:
I don't see how flashing many ROMs could cause your battery life to drop. However the following issues are possible:
1) The ROM you are using has a bug that is causing some type of battery drain. These do happen.
2) You have charged and discharged your battery so many times that it cannot hold a charge anymore. I start noticing battery life decreasing after about 2 years of my usage (generally fairly low). Most times my battery life does not drop below 60% or so. If you very often let it drop very low, I can see the battery life decrease significantly after about a year.
Click to expand...
Click to collapse
Yea, I can only assume that because I have let it drop so low many times, I might have ruined the cells within. I might just end up buying a new battery. Thanks.
My sgs2 GT-I9100 got a new battery because the original one got swollowen , but now it also has problems occurred Recently,
Phone flickers and goes completely off at 40%-50% ,
Wont turn on again unless i plug it in but then it shows 0%,
Happens all the time,
So I restarted the phone at 50% to see SUPRISE then it shows less than 5% battery !
But after 50% its sure phone will go off any sec.
Is there a fix other than going to another new battery again? Tried the Battery Calibration app By a XDA member too...
UPDATE: Got anew battery ( 2nd battery purchase within a month) but it seems to be the problem continues..
Used the battery with the charge it came with... 60% browsed the web...... reached 35%...... Turned off again
Thinking that it happens because of a miscalibration so used the above mentioned app and calibrated at 100% drained till 40% ( light gaming) Went off again....:crying:
Please Help this is urgent!!!!!:fingers-crossed:
UPDATE 1
Did a Reset of the device and charged it fully with the brand new battery (left for couple of hrs after 100%) and I eventually drained it to 50% and did a restart I was left with 10% after.... didn't fixed
I'll try my best to help. Had this problem with an old laptop battery. I just looked a bit around and found that there are several apps that show you the real mAh. SInce I haven't tested of them I won't recommend any.
Are your contacs all clean? Can you measure the output of the battery with a voltage meter?
EDIT: Found this a few posts lower " just reset the fuel gauge chip (rooted) and you are good to go!"
Update flashed a stock jellybean rom lets see what happens