Related
I had on the phone 059N169_1600.3013.8107.11502. Then I update to 059M5Z7_1600.3015.8107.12070. I did it by the recovery option in the NCS. This version hasn't my language and I tried to change to 059N3S9_1600.3014.8107.12050.
When my phone was rebooted, the computer detected it other than ever. I saw Qualcomm CDMA Technologies MSM and removable disk with question about formatting. I clicked cancel but NCS does not detect the phone. My computer couldn't install driver for Qualcomm CDMA Technologies MSM.
I tried to do refurbish and recovery on 3 computers. I always got the same result.
Can anyone help me?
no solution
68 views and no reply, lumia 710 is truly unpopular..
I have the same problem, and I guess our only hope is the official tango update from zune.
I think the official tango update from zune nothing will change. I think that the Zune also does not recognize the phone after the restart.
adiksw said:
I had on the phone 059N169_1600.3013.8107.11502. Then I update to 059M5Z7_1600.3015.8107.12070. I did it by the recovery option in the NCS. This version hasn't my language and I tried to change to 059N3S9_1600.3014.8107.12050.
When my phone was rebooted, the computer detected it other than ever. I saw Qualcomm CDMA Technologies MSM and removable disk with question about formatting. I clicked cancel but NCS does not detect the phone. My computer couldn't install driver for Qualcomm CDMA Technologies MSM.
I tried to do refurbish and recovery on 3 computers. I always got the same result.
Can anyone help me?
Click to expand...
Click to collapse
i have the same problem, but i formatted that removable disk, now, my PC not recognice my lumia!!! some help will be ok thanks.
andrexinho said:
i have the same problem, but i formatted that removable disk, now, my PC not recognice my lumia!!! some help will be ok thanks.
Click to expand...
Click to collapse
By formatting that disk you accidently removed the bootloader from your Lumia. See this thread for details: http://forum.xda-developers.com/showthread.php?t=1587650, specifically THIS post.
I don't know if it possible to recover from this. You might want to try to perform a recovery flash instead of the more general refurbish one. Instructions can be found on this forum or by a quick google (here for example). Please note that as you have formatted the bootloader partition your phone might not even want to go to the recovery mode (most likely this requires a working bootloader), in that case your phone is bricked . Good luck.
Briefcase said:
By formatting that disk you accidently removed the bootloader from your Lumia. See this thread for details: http://forum.xda-developers.com/showthread.php?t=1587650, specifically THIS post.
I don't know if it possible to recover from this. You might want to try to perform a recovery flash instead of the more general refurbish one. Instructions can be found on this forum or by a quick google (here for example). Please note that as you have formatted the bootloader partition your phone might not even want to go to the recovery mode (most likely this requires a working bootloader), in that case your phone is bricked . Good luck.
Click to expand...
Click to collapse
so is no possible to recover the bootloader? in this case if my phone is bricked, isn´t there any solution? thanks.
andrexinho said:
so is no possible to recover the bootloader? in this case if my phone is bricked, isn´t there any solution? thanks.
Click to expand...
Click to collapse
If the recovery flashing method I linked in my previous post does not work I think your phone is in an unrecoverable state (bricked). It may be that some-one else here knows how to recover, but missing/corrupted bootloaders usually mean you have to use something like JTAG to recover. And that's a difficult proces which in most cases requires hardware modifications (soldering and such). Currently no such details for the lumia exist.
Of course Nokia can fix your phone but since you tried flashing the phone yourself that is gonna cost you some money i'm afraid.
Briefcase said:
If the recovery flashing method I linked in my previous post does not work I think your phone is in an unrecoverable state (bricked). It may be that some-one else here knows how to recover, but missing/corrupted bootloaders usually mean you have to use something like JTAG to recover. And that's a difficult proces which in most cases requires hardware modifications (soldering and such). Currently no such details for the lumia exist.
Of course Nokia can fix your phone but since you tried flashing the phone yourself that is gonna cost you some money i'm afraid.
Click to expand...
Click to collapse
ok im afraid my cell is death permanently, here in Colombia there arent nokia service center, just cellular operators like Comcel have technical services but they only repair celphones if you bought the cellphone there.
im going to wait if in a soon future there is a solution to my problem, thanks.
andrexinho said:
i have the same problem, but i formatted that removable disk, now, my PC not recognice my lumia!!! some help will be ok thanks.
Click to expand...
Click to collapse
wow why would you even try to format anything of your phone. It will take lots of time for some gurus here to help you get back the bootloader.
andrexinho said:
so is no possible to recover the bootloader? in this case if my phone is bricked, isn´t there any solution? thanks.
Click to expand...
Click to collapse
as I read all threads about that magic storage mode , you need to get it in storage mode (seen as a drive) and then you can try to copy the stuff posted here ( http://forum.xda-developers.com/showpost.php?p=24607410&postcount=25 ) to the partitions found on your phone .
yes I know you have another phone but it is a try to get a bootloader on that phone again , after that you could try to flash a normal bootloader and rom for your phone.
zeronk said:
68 views and no reply, lumia 710 is truly unpopular..
I have the same problem, and I guess our only hope is the official tango update from zune.
Click to expand...
Click to collapse
IF it still boots to usb disk mode, you can recover. You need a dd dump from the 3rd partition of the phone, or from some other phone (lumia 710, don't try with 800 since partition layouts will be different) and dump it back. You should get your 3rd bootloader back. If you messed up the entire partition table OR you deleted the first partition... you made a pretty good mess.
dd dump
biktor_gj said:
IF it still boots to usb disk mode, you can recover. You need a dd dump from the 3rd partition of the phone, or from some other phone (lumia 710, don't try with 800 since partition layouts will be different) and dump it back. You should get your 3rd bootloader back. If you messed up the entire partition table OR you deleted the first partition... you made a pretty good mess.
BE CAREFUL WITH THE 64KB SIZE PARTITION. IF YOU MESS IT UP YOU LOOSE NETWORK.
Click to expand...
Click to collapse
boot into usb disk mode, dd dumped 3rd partition then dd it back, but when I plug phone into windows 8 there is still the format prompt.
Did u mean that I need dd dumped from a health 710?
At least Disk Mode is still working
Yes, you need a dump from a working phone. If you feel brave, you can try with the copy from my lumia 800: http://www.mediafire.com/download.php?lllk9lx8972t63k
Windows will always tell you the partition needs to be formatted, but you HAVE to press cancel, otherwise youll break it again. Windows cant see into any of lumia's partitions, but with linux you can see the contents and modify them.
Try to dd the partition to the phone, then run 'sync' on the terminal, then unplug the phone, hold 10 seconds the power button to turn it off and try to turn it back on normally. If the rest of the partitions are fine, it should boot, with all your data intact...
serial mode
biktor_gj said:
At least Disk Mode is still working
Yes, you need a dump from a working phone. If you feel brave, you can try with the copy from my lumia 800: http://www.mediafire.com/download.php?lllk9lx8972t63k
Windows will always tell you the partition needs to be formatted, but you HAVE to press cancel, otherwise youll break it again. Windows cant see into any of lumia's partitions, but with linux you can see the contents and modify them.
Try to dd the partition to the phone, then run 'sync' on the terminal, then unplug the phone, hold 10 seconds the power button to turn it off and try to turn it back on normally. If the rest of the partitions are fine, it should boot, with all your data intact...
Click to expand...
Click to collapse
my phone still works normally, and usb mode is fine too. The only thing not working seems to be serial mode, and I can't use recovery or refurbish flash in nokia care suit.
I won't try files from lumia 800 through, but thx anyway.
Maybe who have jtag pinout for this phone (710) (800)
Hello Lumia Users,
with the discovery of the Qualcomm mode we are finally able to unlock our devices as well. However the process of flashing involves always a certain risk: the risk of making the device unusable, the so called bricks. I created this thread to prevent huge amounts of posts discussing methods to revive bricked devices.
You use all the methods and techniques described in this thread at your own risk. We are not responsible for any damage or loss of waranty.
Before you post in this thread please gather some information first.
1. How dead is your phone:
Does it vibrate when you hold the on/off button?
If not: leave your phone on the originale charger (with the supplied cable) for 8 to 10 hours and try again.
Does it vibrate when you hold the volume-down+power+camer button?
Are you able to enter the Qualcomm mode?
2. Details about the flashing process
What operating system did you use to flash your phone?
If you are running Linux and you are able to enter Qualcomm mode connect your Lumia in Qualcomm mode. Create a list of the lumias partitions (fdisk -l) and include it in your post.
Do you remember the command you used to flash the phone?
Sometimes you can Access the previous commands on the command prompt by pressing the up-arrow on your keyboard
Do you remember the output of the dd command?
What ROM did you flash?
Did you perform a hardreset after flashing?
3. Additional info:
Do you have a Nokia Care Point or carrier store nearby?
Did you create dumps/backups of the partitions before flashing the ROM?
Have you ever used NCS or some other tools to flash firmware to the device?
How bricked is my phone?
It vibrates. Connects to MAC osx and Windows. Will not connect in Ubuntu. Able to enter qualcomm disk mode, doesn't show up in ubuntu. Might be able to reflash it in mac osx though, or restore the partition I screwed up from an IMG file of that partition.
I used ubuntu to flash it. I accidentally flashed the 3rd partition of it. The command I used was
dd if=/Home/David/os-new.nb of=/dev/sdB3
The output said something about copying over the .nb file correctly..
I used the full unlock rom by lucifier. Nothing wrong with me. My fault on the incorrect flashing.
wardoc22 said:
How bricked is my phone?
It vibrates. Connects to MAC osx and Windows. Will not connect in Ubuntu. Able to enter qualcomm disk mode, doesn't show up in ubuntu. Might be able to reflash it in mac osx though, or restore the partition I screwed up from an IMG file of that partition.
I used ubuntu to flash it. I accidentally flashed the 3rd partition of it. The command I used was
dd if=/Home/David/os-new.nb of=/dev/sdB3
The output said something about copying over the .nb file correctly..
I used the full unlock rom by lucifier. Nothing wrong with me. My fault on the incorrect flashing.
Click to expand...
Click to collapse
The big question is: Are the other partitions intact? biktor_gj has uploaded some dumps over at the development thread. You could try to flash the sdX3 Partition in OSX. However I think it is strange that Ubuntu wont recognise the device. You can use the df command to get all connected devices on Ubuntu.
ChrisKringel said:
The big question is: Are the other partitions intact? biktor_gj has uploaded some dumps over at the development thread. You could try to flash the sdX3 Partition in OSX. However I think it is strange that Ubuntu wont recognise the device. You can use the df command to get all connected devices on Ubuntu.
Click to expand...
Click to collapse
Im pretty darn sure the other partitions are still intacted as I only flashed the 3rd partition.
I know about the DF command. Yea, it doesn't show up in ubuntu. :/
Also, are the dumps he uploaded for the lumia 710?
wardoc22 said:
Im pretty darn sure the other partitions are still intacted as I only flashed the 3rd partition.
I know about the DF command. Yea, it doesn't show up in ubuntu. :/
Click to expand...
Click to collapse
That is really weird. I see two realistic options here:
a) Download the sdb9.rar posted by biktor_gj and flash it as IMG file on OSX
or
b) Ask for a repair of the device.
wardoc22 said:
Also, are the dumps he uploaded for the lumia 710?
Click to expand...
Click to collapse
I doubt it since he mentioned a 15GB partition. Do you own a Lumia 710?
ChrisKringel said:
That is really weird. I see two realistic options here:
a) Download the sdb9.rar posted by biktor_gj and flash it as IMG file on OSX
or
b) Ask for a repair of the device.
I doubt it since he mentioned a 15GB partition. Do you own a Lumia 710?
Click to expand...
Click to collapse
Yea, Tmobile agreed to send me in a new lumia 710.
I tried the df command in mac osx in terminal and the phone didnt show up. So I guess my only option is to try to revive it with an IMG of the 3rd partition of the device within disk utility. Since I am getting a new device anyways, might as well try to do whatever I can to contribute.
Do you have a 710? Would you mind uploading an image file for the 3rd partition for me?
wardoc22 said:
Yea, Tmobile agreed to send me in a new lumia 710.
I tried the df command in mac osx in terminal and the phone didnt show up. So I guess my only option is to try to revive it with an IMG of the 3rd partition of the device within disk utility. Since I am getting a new device anyways, might as well try to do whatever I can to contribute.
Do you have a 710? Would you mind uploading an image file for the 3rd partition for me?
Click to expand...
Click to collapse
I only own a Lumia 800 (with a locked bootloader). However there is a recovery flash method for the Lumia 800. You could try to adapt this method for the Lumia 710.
ChrisKringel said:
I only own a Lumia 800 (with a locked bootloader). However there is a recovery flash method for the Lumia 800. You could try to adapt this method for the Lumia 710.
Click to expand...
Click to collapse
NCS won't work with a phone that have qualcomm bootloader. I have a qualcomm bootloader on my lumia 710.
I can only flash it with QSPT, but I can't figure out how to work it.
wardoc22 said:
NCS won't work with a phone that have qualcomm bootloader. I have a qualcomm bootloader on my lumia 710.
I can only flash it with QSPT, but I can't figure out how to work it.
Click to expand...
Click to collapse
Some guys flashed their Qualcomm Lumia 800s with NCS wich resulted in an upgrade of their bootloader. According to you this is impossible with the unlocked phones so I guess you have to sent your device in for a repair.
The Images on NaviFirm sometimes contain IMGs of the partitions. You could also try your luck there.
1. My Phone does not vibrate. I charged it the whole night. I can't enter Qualcomm Mode.
2. I used Ubuntu 12.04 with dd if="FullUnlock-os-new.nb" of = "/def/sdd9". There was no output. I used the ROM provided here: ROM. Yes, I performed a Hardreset.
3. No, I don't think so. Yes, i created an image backup of every partition. I tried to recover my phone with the NCS. It did not find my Lumia.
My phone worked like a charme. Yesterday I installed Battery Status and started the Task Manager. My phone crashed, and after a restart it lagged. So I rebooted and now it won't start anymore. I think about sending it to Nokia, but maybe you can help me first.
MrGreenTea said:
1. My Phone does not vibrate. I charged it the whole night. I can't enter Qualcomm Mode.
2. I used Ubuntu 12.04 with dd if="FullUnlock-os-new.nb" of = "/def/sdd9". There was no output. I used the ROM provided here: ROM. Yes, I performed a Hardreset.
3. No, I don't think so. Yes, i created an image backup of every partition. I tried to recover my phone with the NCS. It did not find my Lumia.
My phone worked like a charme. Yesterday I installed Battery Status and started the Task Manager. My phone crashed, and after a restart it lagged. So I rebooted and now it won't start anymore. I think about sending it to Nokia, but maybe you can help me first.
Click to expand...
Click to collapse
If it does not turn on you can only get a replacement from your carrier or send it in for a repair. If you manage to enter the Qualcomm mode it would be possible to reflash the partitions, but I guess thats impossible since it wont turn on.
My phone doesn't vibrate too. I also noticed that probably all circuits used to charge the battery are actually driven by software (I used small LED to test it, after 10h of charging no light at all)
I also tried plugging in the USB charger without battery inside the device. no luck
Bootloader unlock through NCS went smooth, for dd'ing I used Windows 7 Home Premium x64(6.1.7601) with admin CLI
Command: dd if=c:\lum710rom.nb of=\\.\g:
...wrote about 1100 kBytes of data, then stopped and outputted errors
ChrisKringel said:
If it does not turn on you can only get a replacement from your carrier or send it in for a repair. If you manage to enter the Qualcomm mode it would be possible to reflash the partitions, but I guess thats impossible since it wont turn on.
Click to expand...
Click to collapse
Funny thing is, after like 5 hours plugged into my computer, it started the qualcomm mode and now I am reflashing the backed up partitions. Do I have to perform a hard reset after the reflash?
MrGreenTea said:
Funny thing is, after like 5 hours plugged into my computer, it started the qualcomm mode and now I am reflashing the backed up partitions. Do I have to perform a hard reset after the reflash?
Click to expand...
Click to collapse
I think you should do a hard reset.
I will also try having the phone connected for longer period of time, maybe that should be the solution to our problems!
rbusa said:
I think you should do a hard reset.
I will also try having the phone connected for longer period of time, maybe that should be the solution to our problems!
Click to expand...
Click to collapse
Yes, you can try that and I recommend using ubuntu for flashing with dd. You can install it easily with wubi and uninstall it as easy from within Windows.
EDIT: Just as I wanted to say it didn't work, it started I am so ****ing happy now, you would not believe
I was trying to downgrade my Lumia 710 and I got this error
Loading hashblock failed with ‘Messenger encountered error ‘Referencia a objeto no establecida como instancia de un objeto.’’
en Nokia.Wezen.Programming.SequenceLogic.HashLoader.C heckForErrors()
en Nokia.Wezen.Programming.SequenceLogic.ImageLoader. LoadBinaryData(ImageBinaryData binaryData, HashLoader hashLoader, ImageCertificate certificate)
en Nokia.Wezen.Programming.SequenceLogic.ImageLoader. LoadImageFile(ImageBinaryData binaryData, ImageCertificate writeCertificate)
en Nokia.Wezen.Programming.SequenceLogic.ProgrammingL ogic.ProgramImageFiles(EraseMethod eraseMethod)
en Nokia.Wezen.Programming.Programmer.Program()
en Nokia.Wezen.Product.Programming.FirmwareUpdate.Wez enFirmwareUpdate.Recovery()
en Nokia.CareSuite.PlugIns.WezenRecovery.RecoveryDial og.RecoveryDialogModel.Flash()
en Nokia.CareSuite.PlugIns.WezenRecovery.RecoveryDial og.RecoveryDialogModel.<HandleDownloadVariantPacka geCompleted>b__7(Object state)
Click to expand...
Click to collapse
I can power it, but it stays in Nokia
It vibratess when I hold the volume-down+power+camera button but i cant hard reset my phone
What's Qualcomm mode?
I used windows to flash it
I can't remember commands
rbusa said:
My phone doesn't vibrate too. I also noticed that probably all circuits used to charge the battery are actually driven by software (I used small LED to test it, after 10h of charging no light at all)
I also tried plugging in the USB charger without battery inside the device. no luck
Bootloader unlock through NCS went smooth, for dd'ing I used Windows 7 Home Premium x64(6.1.7601) with admin CLI
Command: dd if=c:\lum710rom.nb of=\\.\g:
...wrote about 1100 kBytes of data, then stopped and outputted errors
Click to expand...
Click to collapse
I would always recommend to use a Linux Distribution in order to apply the unlock. Windows has sometimes problems with partitioned removable devices. Did you manage to boot up in Qualcomm mode? I assume the Windows dd command wrote to the wrong partition.
MrGreenTea said:
Funny thing is, after like 5 hours plugged into my computer, it started the qualcomm mode and now I am reflashing the backed up partitions. Do I have to perform a hard reset after the reflash?
Click to expand...
Click to collapse
Always perform a hard reset after manipulating the OS partition.
rogelioc93 said:
I was trying to downgrade my Lumia 710 and I got this error
I can power it, but it stays in Nokia
It vibratess when I hold the volume-down+power+camera button but i cant hard reset my phone
What's Qualcomm mode?
I used windows to flash it
I can't remember commands
Click to expand...
Click to collapse
Does your device enter Qualcomm mode when you hold Vol Down+Power to power it on? You should be able to see it either popping up in your Explorer or in the Device Manager. Another method to hard reset the phone is:
1. Switch the phone off.
2. Press and hold the Volume Down, Power and Camera buttons at the same time.
3.When the phone vibrates release the Power button but keep the Camera and Volume Down buttons held for a further five seconds.
ChrisKringel said:
Did you manage to boot up in Qualcomm mode? I assume the Windows dd command wrote to the wrong partition.
Click to expand...
Click to collapse
Well, I am not able to boot up in Qualcomm mode anymore...
rbusa said:
Well, I am not able to boot up in Qualcomm mode anymore...
Click to expand...
Click to collapse
If your phone won't power on you can either bring it to a Care Point and ask for reflashing or send it in for a repair.
Gyus, I need help - after downgrading FW from 12140 back to 12072, REFURBISH failed.
I used Nokia Care Suite.
Now, I have Lumia 800 stucks on Nokia logo and nothing works.
PC does not detect it, I tried resets, but w/o success.
It vibrates, but it stays on Nokia logo screen.
Please, can you help me?
Hello.
I was trying to install a treble rom on my p20 lite and suddenly after flashing i needed to flash stock recovery to make the stock wipes.
I did.
The rom started but with no keyboard. I couldnt pass google part to get to the rom menu.
Ok.
I decided to flash it again.
I did. But this time, the rom never started and i was with stock erecovery, so couldnt flash again.
I went to flash twrp but FRP is LOCKed. Bootloader unlocked, obviously. And bc of that i cant flash ANYTHING.
Tried to flash system, twrp, anything. I cant. Says FRP lock.
Tried to lock bootloader and relock again: I cant. It says it needs to unlock FRP before.
Tried DC PHOENIX, didn't work on my p20.
Scrolled all google and xda for help, nothing.
Tried erecovery stock rom installation. It downloads the files but never installs, i've spent 5 hours waiting for it to go off the 0%. Nothing happens.
Already made erecovery wipe data/cache. Nothing.
Can someone please help me?
Hi there
Can you tell what's your build number if you already knew before this happened?
Also, right now your only hope is your Stock Recovery so let's focus on that:
Please try to download and install the official ROM via the eRecovery a couple of times and connect it to the best Wifi you have.
Do you have bootloader "unlocked" or "locked" right now?
FRP is locked so no changes possible yup.
If you have your bootloader "locked" not "relocked" you have warranty and you can send it to a customer repair center and they can solve it for you.
With the methods we know it's pretty much impossible, altough try this via fastboot command line:
fastboot erase config
then
fastboot reboot
If this does not do it then try with DC-Unlocker software via this link https://www.dc-unlocker.com/huawei-android-phone-frp-unlock
Sorry for insisting,
Best of hopes,
AS
ars_chelsea said:
Hi there
Can you tell what's your build number if you already knew before this happened?
Also, right now your only hope is your Stock Recovery so let's focus on that:
Please try to download and install the official ROM via the eRecovery a couple of times and connect it to the best Wifi you have.
Do you have bootloader "unlocked" or "locked" right now?
FRP is locked so no changes possible yup.
If you have your bootloader "locked" not "relocked" you have warranty and you can send it to a customer repair center and they can solve it for you.
With the methods we know it's pretty much impossible, altough try this via fastboot command line:
fastboot erase config
then
fastboot reboot
If this does not do it then try with DC-Unlocker software via this link https://www.dc-unlocker.com/huawei-android-phone-frp-unlock
Sorry for insisting,
Best of hopes,
AS
Click to expand...
Click to collapse
Hey, thanks for the answer.
My build number (ane-lx3 c605 b149)
I tried for like 10 times already to install the firmware from erecovery but it refuses to leave the 0% when installing... Ive waited more than 5 hours already.
When trying these fastboot command lines, i got this: https://imgur.com/a/hrSB8iK
Dc also didnt worked for me, i think it doesnt support my phone model?
Bc i can't find it in the list of phone model in the software also tried with similar and doesnt work.
My bootloader is unlocked, i guess warranty wont solve my problem bc of that :crying:
Thanks again for tryna help!
you need sd card
download this file: https://androidhost.ru/cBe
unzip this file, inside software folder are dload folder, coppy that to sd card
put sd card in phone
pres vol+ and vol- and power button (need atlest 50% batery)
give a try.
Arnys said:
you need sd card
download this file: https://androidhost.ru/cBe
unzip this file, inside software folder are dload folder, coppy that to sd card
put sd card in phone
pres vol+ and vol- and power button (need atlest 50% batery)
give a try.
Click to expand...
Click to collapse
He/She does need a micro sd card adapter for that to connect to the pc or use it on another phone and then copy the files.
Yeah I forgot about that I guess XD
Cheers,
AS
ars_chelsea said:
He/She does need a micro sd card adapter for that to connect to the pc or use it on another phone and then copy the files.
Yeah I forgot about that I guess XD
Cheers,
AS
Click to expand...
Click to collapse
Arnys said:
you need sd card
download this file: https://androidhost.ru/cBe
unzip this file, inside software folder are dload folder, coppy that to sd card
put sd card in phone
pres vol+ and vol- and power button (need atlest 50% batery)
give a try.
Click to expand...
Click to collapse
Thank you, guys.
I tried this method just now but after a time with EMUI logo in the screen it said software install failed!
I guess im really lost. :crying:
fcknumb said:
Thank you, guys.
I tried this method just now but after a time with EMUI logo in the screen it said software install failed!
I guess im really lost. :crying:
Click to expand...
Click to collapse
Hey
Did you try the official guide of @Merlin_99?
If not check his thread here: https://forum.xda-developers.com/huawei-p20-lite/how-to/root-how-to-install-update-t3841557
That's the official way to do it
Cheers,
AS
ars_chelsea said:
Hey
Did you try the official guide of @Merlin_99?
If not check his thread here: https://forum.xda-developers.com/huawei-p20-lite/how-to/root-how-to-install-update-t3841557
That's the official way to do it
Cheers,
AS
Click to expand...
Click to collapse
Thanks for your reply and still tryna help me.
As i see, the only thing i didnt do from the official guide is this part:
"Finally, enter to the project menu from dialer typing *#*#2846579#*#* ==> Software Upgrade ==> SdCard Upgrade."
That i cant do cause my phone is systemless and i cant turn it on to use dialer :crying:
fcknumb said:
Thanks for your reply and still tryna help me.
As i see, the only thing i didnt do from the official guide is this part:
"Finally, enter to the project menu from dialer typing *#*#2846579#*#* ==> Software Upgrade ==> SdCard Upgrade."
That i cant do cause my phone is systemless and i cant turn it on to use dialer :crying:
Click to expand...
Click to collapse
Okay then.
It should work though did you put the dload folder into the root your sd card and then power on button + Volume buttons at the same time while powering on?
Cheers,
AS
ars_chelsea said:
Okay then.
It should work though did you put the dload folder into the root your sd card and then power on button + Volume buttons at the same time while powering on?
Cheers,
AS
Click to expand...
Click to collapse
Right bae, its like that into my sdcard: 1. http://prntscr.com/lx74xt 2. http://prntscr.com/lx7im7
And yes, i did pressed power and + - volume buttons at same time!
Thank you for not giving up.
fcknumb said:
Right bae, its like that into my sdcard: 1. http://prntscr.com/lx74xt 2. http://prntscr.com/lx7im7
And yes, i did pressed power and + - volume buttons at same time!
Thank you for not giving up.
Click to expand...
Click to collapse
Hi again
This is really weird... This one should work... Did you download the right version of your build? example: 8.0.0.162(C432)
And try to find the latest version of your build and via your model example: ANE-LX1 which is on the back of the phone with small letters or on the box
Cheers,
AS
ars_chelsea said:
Hi again
This is really weird... This one should work... Did you download the right version of your build? example: 8.0.0.162(C432)
And try to find the latest version of your build and via your model example: ANE-LX1 which is on the back of the phone with small letters or on the box
Cheers,
AS
Click to expand...
Click to collapse
Yeah, i did it all right.
So sad...
fcknumb said:
Yeah, i did it all right.
So sad...
Click to expand...
Click to collapse
Remote instructions are not the best for these problems, so try to get a person on your country which knows some stuff and can help you out there
LG G6 Unbrick
First Thing First: If you try this method, I nor anybody else is responsible
for any further damage done to your phone.
!!!YOU CANNOT FLASH THIS TO AN H872!!!
If you have destroyed the partitions, you are going to have to try Method 2 (Second Post)
Models Confirmed: LS993, H871, H870ds, H870, AS993
READ THE ENTIRE GUIDE OVER BEFORE STARTING
Files needed:
All Here : https://drive.google.com/open?id=1OQnP2tu7hqlR0tbEdxLnzj_xOx12Ndvu
CLICK “DOWNLOAD ALL” IN TOP RIGHT CORNER
Working KDZ for your model : https://lg-firmwares.com/
UNBRICK PROCEDURE:
(DO NOT CONNECT PHONE UNTIL STEP 6)
Step 1) Download Files ---> Duh, lol
Step 2) Install QDLoader Driver (Select the driver for your system, 32 or 64-bit)
Use The new Signed driver.
Step 3) Extract AS993 to a folder. Any folder will work.
Step 4) Copy FireHose to same folder as AS993.
Step 5) Extract Qualcomm_Flash_Image_Loader_v2.0.1.9 to any folder.
Step 6) Start QFIL.
Under “Select Build Type” Select “Flat Build”
Under “Select Programmer” click “Browse”
Browse to the AS993 folder you created earlier and select the Firehose, hit open
In the Title Bar, click Configuration ->FireHose Configuration
Uncheck every checkbox, choose “Sahara” in Download Protocol dropdown, and “ufs” in
Device Type dropdown
Hit OK
Under “Select Flat Build” click “Load XML”
Browse to AS993 folder and select every rawprogram XML and hit open.
A windows will pop up asking to select Patch XML, Select every Patch XML, and hit open.
Connect Phone and click Download
If you encounter an error, try to reboot the phone and try download again
(Hold Vol Down + Power until you see COM port disappear and show up again)
Wait for download to finish.......
Phone will reboot to Fastboot
Step 7) Install LGUP_Store_Frame_Ver_1_14_3
Step 8) Extract LGUP Patch rar to rogram Files:\LG Electronics\LGUP
Put Phone into Download Mode (Unplug Phone → Turn phone off → Hold Vol Up → Plug Phone In)
Step 9) Run LGUP
In Model List window choose your phone and click Select
Under “Process” Select “Partition DL”
Under “File Path” to the right of “Bin File” click the button with 3 periods
Select your working KDZ
Click Start
A window will pop-up with partitions. Check select all, and then OK
Another window will pop-up explaining which partitions will change, click Yes
Wait for Flash to complete.......
!!!AFTER RESTART, YOU MUST FACTORY RESET!!!
To Perform Factory Reset Do The Following:
HOLD VOL DOWN + POWER, AS SOON AS YOU SEE BOOT SCREEN, RELEASE POWER BUTTON FOR A MOMENT, THEN CONTINUE HOLDING POWER AND VOL DOWN.
!!!DO NOT RELEASE POWER OR VOL DOWN BUTTONS UNTIL FACTORY RESET MENU APPEARS!!!
Use VOL UP\DOWN to choose to complete Factory Reset, then hit Power Button to perform Factory Reset.
CONGRATULATIONS! YOUR PHONE IS NOW UNBRICKED!
ScreenShots to Come, and Edits to be made.
Edit: H870ds, H870 and AS993 added to working models
Removed old drivers from Google Drive for simplicity.
Reserved
Thank bro
LGM-600l
Please help me create fade rawprogram XML and Patch XML for lgm-g600l. thanks a lot.
Is us988 work?
jascharichter said:
Is us988 work?
Click to expand...
Click to collapse
Although it has not been tested, there is no reason it shouldn't work. The worse that could happen is you're stuck in the same situation.
Firehose exists for g6 now? Would this allow me to safely pry at LG's bootloader without permanent bricks? Would love to take it into my own hands but couldn't afford the risks before. I'm using a Canadian H873
Tinyshy said:
Firehose exists for g6 now? Would this allow me to safely pry at LG's bootloader without permanent bricks? Would love to take it into my own hands but couldn't afford the risks before. I'm using a Canadian H873
Click to expand...
Click to collapse
Yep. Have at it. But, like always, I don't recommend purposely bricking.
I should mention that you don't need to use the xml stuff.
In QFIL in one of the top menus, there's a partition option, where it reads the gpt from the phone and you can select them and flash individual files. So you can flash directly bootloader
or whatever you need from your proper kdz source.
Lot's of people have wrecked there partition table trying to unbrick. That is why I included them.
inbox me
Dylan110494 said:
Please help me create fade rawprogram XML and Patch XML for lgm-g600l. thanks a lot.
Click to expand...
Click to collapse
inbox me inbox me
jthein1989 said:
Lot's of people have wrecked there partition table trying to unbrick. That is why I included them.
Click to expand...
Click to collapse
I'm sorry. I have been extremely busy lately. I will let you know when I get them done.
Tinyshy said:
Firehose exists for g6 now? Would this allow me to safely pry at LG's bootloader without permanent bricks? Would love to take it into my own hands but couldn't afford the risks before. I'm using a Canadian H873
Click to expand...
Click to collapse
Did you try it yet?
I'm also trying to fix a dead Canadian H873 (Videotron Carrier). Had tried my hand in the past at creating the patch.xml and rawprog0.xml (one method had me peek at the gpt files using an excel/libreoffice spreadheet) but failed for various reason also not having a proper programmer file didn't help any.
For those that encounter issues with either the programmer file failing or getting sahara fail FHLoader, something like cannot find system file try this:
1. Make sure to reboot phone and hit download to phone in QFIL right away. On my device sahara seemed to be timing out quickly.
2. For the second error using the QFIL included with QPST 2.7.474 fixed it.
Sadly i tried to refresh the phone using the backup files i was given with it but now it doesn't get detected. Holding power button the phone vibrates and nothing else happens. Tread lightly.
So good news the programmer file works (tried it on a H873 Videotron variant), bad news do it right the first time or else.
Time to start searching for a way to force it back into edl.
draekko said:
Time to start searching for a way to force it back into edl.
Click to expand...
Click to collapse
To clarify i used a backup of the files i had on hand for the device and not the files provided by OP.
Hi everyone, I have just bricked my G6, hard brick I think ( does not charge, cant get into download mode, cant hard reset either, only show Qualcomm qloader 9008"). This happened after I tried cross flashing it from LS993 to H872 ( I now know that a NO NO ). Can someone here help me on how to get it back to life ? I ve read quite a lot of different topics but the more I research the more confused I am. Some say I need to restore to stock firmware, but there is no stock firmware for LS993... Any help would be greatly appreciated and I hope you have a very great day
Read my method, download the files, read it again, and follow the steps.
jthein1989 said:
Read my method, download the files, read it again, and follow the steps.
Click to expand...
Click to collapse
I did but I am still so confused. Can you please tell me which firmware should I download and the firehose to use too. I think I understood most of the post here, except those 2 things: kdz and firehose.
jthein1989 said:
Read my method, download the files, read it again, and follow the steps.
Click to expand...
Click to collapse
Friend, I congratulate you for your great contribution and help many. I have the same problem but the program tells me that ...
download fail: Sahara Fail: QsaharaServer Fail: Process Fail.
ps: I have the model H870
---------- Post added at 08:53 AM ---------- Previous post was at 08:39 AM ----------
jthein1989 said:
Read my method, download the files, read it again, and follow the steps.
Click to expand...
Click to collapse
Friend, I congratulate you for your great contribution and help many. I have the same problem but the program tells me that ...
download fail: Sahara Fail: QsaharaServer Fail: Process Fail.
ps: I have the model H870
Hi!
I am trying to follow the steps shown but my computer do not recognize my H870 in "select" port :/
any idea?
thank you very much
Man... I have tried so many different IMEI Repair tools, Phones rooted (Magisk) and I have TWRP.. I backed up QCN with my null IMEI but cannot find the Hex or the "088A" Starting numbers for it to change it back to my original IMEI. If anyone has any ideas, please let me know. I will attach some pics and programs/tools I been using.. I was able to finally get a green light and pass on this one tool after I Extracted the files into platform tools and took ownership of the (tool).exe, however, after rebooting my phone, *#06# still reads "NULL"
abovethegov said:
Man... I have tried so many different IMEI Repair tools, Phones rooted (Magisk) and I have TWRP.. I backed up QCN with my null IMEI but cannot find the Hex or the "088A" Starting numbers for it to change it back to my original IMEI. If anyone has any ideas, please let me know. I will attach some pics and programs/tools I been using.. I was able to finally get a green light and pass on this one tool after I Extracted the files into platform tools and took ownership of the (tool).exe, however, after rebooting my phone, *#06# still reads "NULL"
Click to expand...
Click to collapse
any solution?, i have same problem,
abovethegov said:
Man... I have tried so many different IMEI Repair tools, Phones rooted (Magisk) and I have TWRP.. I backed up QCN with my null IMEI but cannot find the Hex or the "088A" Starting numbers for it to change it back to my original IMEI. If anyone has any ideas, please let me know. I will attach some pics and programs/tools I been using.. I was able to finally get a green light and pass on this one tool after I Extracted the files into platform tools and took ownership of the (tool).exe, however, after rebooting my phone, *#06# still reads "NULL"
Click to expand...
Click to collapse
yeah grab these files
on your A0.5 firmware an reflash them in fastboot an your imei might be fixed AS THIS METHOD WORKED FOR ME!!
Why are u flashing over persist? Don't do that unless it's your original, some of the partitions on your device are device specific as they contain your IMEI and serial , board number etc... And if they don't match then your radios and other things probably won't work again without reflashing your originals. Anyone feel free to correct me if I lack any info
Why are u flashing over persist? Don't do that unless it's your original, some of the partitions on your device are device specific as they contain your IMEI and serial , board number etc... And if they don't match then your radios and other things probably won't work again without reflashing your originals. Anyone feel free to correct me if I lack any info.... IMEI is stored on efs and persist partitions..... Integrity checks may even cause ur device to fail to boot, just a warning.....
Im pretty sure the whole phone is f*cked.. I flashed it to death.. lol. wont even turn on. screen stays black. Live and let learn I guess.
abovethegov said:
Im pretty sure the whole phone is f*cked.. I flashed it to death.. lol. wont even turn on. screen stays black. Live and let learn I guess.
Click to expand...
Click to collapse
your probably in edl mode right now that's making screen stay black
halloweenm925 said:
your probably in edl mode right now that's making screen stay black
Click to expand...
Click to collapse
Ahhh, so does anyone have a legit msm tool that works in edl mode?
abovethegov said:
Ahhh, so does anyone have a legit msm tool that works in edl mode?
Click to expand...
Click to collapse
I've used the ofp flash tool, but that only worked in fastboot I thought?
abovethegov said:
I've used the ofp flash tool, but that only worked in fastboot I thought?
Click to expand...
Click to collapse
phone phone shouldn't be dead by flashing. try "holding down both vol buttons an power button" for 1 min til phone vibrates
I've tried it. Won't even vibrate or light up to show its charging.