Related
Bought the Trianium Tempered Glass, it was labeled on Amazon for S7 and S6 but I needed something asap so gave it a shot.
Check it out here ABSOLUTELY ridiculous. I believe they just took old stock of S6 screen protectors and stuck a S7 sticker on the back.
It fits, but if you installed it it would slice your front facing camera right in half.
I know everyone is going to start looking for the best screen protectors but this is one everyone should definitely avoid.
Thanks for that. So many of these early screen protectors aren't fitting. This is rediculus.
seoulbrova said:
Bought the Trianium Tempered Glass, it was labeled on Amazon for S7 and S6 but I needed something asap so gave it a shot.
Check it out here ABSOLUTELY ridiculous. I believe they just took old stock of S6 screen protectors and stuck a S7 sticker on the back.
It fits, but if you installed it it would slice your front facing camera right in half.
I know everyone is going to start looking for the best screen protectors but this is one everyone should definitely avoid.
Click to expand...
Click to collapse
This is a known issues for the note 5. I have been through at least 7 screen protectors and each one leaves a halo effect around the screen. There are not going to be a lot of options to avoid this. The only thing I can recommend is buying any non-tempered protectors and trimming the edges. The only problem with this is that your whole screen will not be covered.
Dstu10 said:
This is a known issues for the note 5. I have been through at least 7 screen protectors and each one leaves a halo effect around the screen. There are not going to be a lot of options to avoid this. The only thing I can recommend is buying any non-tempered protectors and trimming the edges. The only problem with this is that your whole screen will not be covered.
Click to expand...
Click to collapse
That's not true, I have a Skinomi one installed right now with absolutely no halo. It does not go edge to edge but there is no visible halo with it.
This one wasn't an issue of a halo, it doesn't even fit at all. If you were to fit it to your phone it would install but the front camera is cut off.
But yes you are right, I have ordered some clear protectors as well.
seoulbrova said:
That's not true, I have a Skinomi one installed right now with absolutely no halo. It does not go edge to edge but there is no visible halo with it.
This one wasn't an issue of a halo, it doesn't even fit at all. If you were to fit it to your phone it would install but the front camera is cut off.
But yes you are right, I have ordered some clear protectors as well.
Click to expand...
Click to collapse
I tried a skinomi on my note 5 had decent halo. I wish I would have taken pictures. It seems like it could be hit and miss depending on the cut of the screen protector and how much beveling on your specific phone. I may be willing to try the skinomi on my s7 it just gets expensive trying 5 different screen protectors.
Hi Guys,
Since there is no good tempered glass or screen protector available for the S7(not edge), Spigen has one but that's way too expensive and I wasn't able to find an authentic one in the market. Has anyone tried protectors and skins by GadgetShieldz? Here's the link-
http://www.gadgetshieldz.com/samsung-galaxy-s7-screen-protectors-covers-cases.html
The plus is that if the product is as good as they are describing then it covers the sides too. The con is that there is no actual proof or hands on video regarding the same+it is still expensive atleast for me but there's no other alternative.
Thanks
I just ordered the matte and the ultra clear screen protectors. I didn't buy the body because I have a Rhinoshield bumper and back protector. I'll post a review once they arrive.
Good product the body shield is
Have been using the Gadgetshielz full body protector for 6 months now. It is quite good and the cuts are precise. Quite a lot of work, applying them is. Be patient after applying, in a week or so, the bubbles and wobbles will sort themselves out. Was hard to believe when I completed installation and saw what a mess it was.
That doesn't look like tempered glass. I will NEVER go back to the flimsy protectors. Too many issues with bubbles, etc. But, I have yet to find a tempered glass that full covers the edges. It's more of an issue when things are right at the edges (such as text) that makes it difficult to read, but I'll take that as it's rare knowing that I have a tempered glass protector on that does a better job of absorbing the shock of a drop.
Using their screen protector, with my rhinoshield bumper case and no bubble. Wanted glass first but all those that I bought, the case lifted them or they had the big halo, lifting all around cause the curve screen.
http://s30.postimg.org/6k9nxdkm9/1.jpg
http://s30.postimg.org/u2bgpk80x/4.jpg
They are working way far better than the TGP.
billubakra said:
Hi Guys,
Since there is no good tempered glass or screen protector available for the S7(not edge), Spigen has one but that's way too expensive and I wasn't able to find an authentic one in the market. Has anyone tried protectors and skins by GadgetShieldz? Here's the link-
http://www.gadgetshieldz.com/samsung-galaxy-s7-screen-protectors-covers-cases.html
The plus is that if the product is as good as they are describing then it covers the sides too. The con is that there is no actual proof or hands on video regarding the same+it is still expensive atleast for me but there's no other alternative.
Thanks
Click to expand...
Click to collapse
Thanks mate. I bought two and will report when it arrives
So, here's why review-
Finally ordered them. It was my first time that I was installing any sort of protector and I was super nervous. The protector kept coming off. I had to wet it with the solutions many times. I drove out the bubbles as many as I could but the end result was way too foggy and messy. But after 48 hours everything was gone, except few dust and fingerprints particles which are my fault BTW there's a huge particle of dust on the back button. Can I lift it up just a tad to remove it? I still have the solution, I am planning to wet it to reapply. Will it work?
Also can anyone suggest a good cover for S7? My current one is a chinese one, but I think it will remove the side protectors if I take the phone out few times because with the side protectors the sides bulge out a bit. @r3xx3r @ere1nion
Any way to get the same cover in India?
iBolski said:
That doesn't look like tempered glass. I will NEVER go back to the flimsy protectors. Too many issues with bubbles, etc. But, I have yet to find a tempered glass that full covers the edges. It's more of an issue when things are right at the edges (such as text) that makes it difficult to read, but I'll take that as it's rare knowing that I have a tempered glass protector on that does a better job of absorbing the shock of a drop.
Click to expand...
Click to collapse
I searched for a month, ordered like 10 different tempered glasses from various websites but they all sucked. GS's protector is not a glass but it is the best alternative to a glass.
An out of context question, what are these four stripes/white lines located on the top and bottom side of the phone for? Just along the charger and speaker in the photos below-
http://www.theinquirer.net/w-images...xys7edgereviewusbport-540x334.jpeg?1458143499
https://fscl01.fonpit.de/userfiles/.../AndroidPIT-Samsung-galaxy-s7-edge-2-w782.jpg
billubakra said:
An out of context question, what are these four stripes/white lines located on the top and bottom side of the phone for? Just along the charger and speaker in the photos below-
http://www.theinquirer.net/w-images...xys7edgereviewusbport-540x334.jpeg?1458143499
https://fscl01.fonpit.de/userfiles/.../AndroidPIT-Samsung-galaxy-s7-edge-2-w782.jpg
Click to expand...
Click to collapse
Those plastic lines are antenna separators. The frame of the phone is used for different antennas, so they must be separated.
MrDusan said:
Those plastic lines are antenna separators. The frame of the phone is used for different antennas, so they must be separated.
Click to expand...
Click to collapse
Thanks Brother. When I saw them for the first time I thought they are there for the light notification purposes.
billubakra said:
Thanks Brother. When I saw them for the first time I thought they are there for the light notification purposes.
Click to expand...
Click to collapse
You're welcome! That would actually be cool
Are U still using those GadgetShieldz? I want to buy them.
MrDusan said:
You're welcome! That would actually be cool
Are U still using those GadgetShieldz? I want to buy them.
Click to expand...
Click to collapse
Yes, since there's no curved/rounded tempered glass available so still using them. Go for them Brother.
Look into rhinosheild. Absolutely unbeliveable. I'll be ordering mine this week.
With that screen protector, ip68, and my otterbox defender; I will never worry about this phone breaking on me.
James.Markham0757 said:
Look into rhinosheild. Absolutely unbeliveable. I'll be ordering mine this week.
With that screen protector, ip68, and my otterbox defender; I will never worry about this phone breaking on me.
Click to expand...
Click to collapse
Not full coverage as per the reviews-
https://rhinoshield.io/products/galaxy-s7-screen-protector?variant=12329024001
An update, I used my phone with the Samsung Gear VR yesterday and when I removed it the protector from the upper side of the phone, where the front camera is got removed I tried to paste the same but it is full of bubbles now . Is anyone else using GS's protector with VR?
billubakra said:
Not full coverage as per the reviews-
https://rhinoshield.io/products/galaxy-s7-screen-protector?variant=12329024001
Click to expand...
Click to collapse
Correct it is not. I use the Otterbox Commuter and Otterbox Defender so this is not an issue for me particularly. I had a partial screen protector on already so no shift in change for me there either. I just received mine in the mail today. The back application was by far harder than the front. I didn't get it perfect. It's the material used on the back. I will not be testing this screen protector but I feel confident with it on. Hopefully it will never need to prove itself.
So, my protector is screwed thanks to Gear VR, it kept on removing the upper part of the protector every time I put the phone in the Gear VR or took it out. Has anyone tried the so called buff guard(a type of tempered glass) which covers the whole screen even the edges? Is there any alternative for the GadgetShieldz protector?
My wife just upgraded to an S7 (tried the Moto Z and it was too big, bulky and heavy for her). She wanted a tempered glass screen protector, but not like the one I have (which doesn't cover the entire screen due to the curved edges of the S7).
After much research, I found the amFilm glass protector was one that was listed in many top-10 lists as being excellent. This covers the entire glass but gives room on the edges for cases. My wife has a Speck Candyshell case for her phone and the screen protector works fine with it. My only issue with it is that on the top and bottom (which is fully protected), it's colored. So you have to choose the correct color based on your phone (black or gold). I don't understand why it has to be colored. Why not make it all clear so you can see the actual color of the phone? But it DOES cover the entire screen unlike the earlier brands that came out. And it was very easy to apply and there are no bubbles at all. Touch response is excellent from what I could tell. I tested it and couldn't find any "soft" or "blind" spots that didn't react and I just lightly touched, so it was pretty good. I'll wait and see how it goes with my wife after she's had it for awhile. It also comes with a lifetime warranty for the purchased product. That means, and they state this in the documentation that comes with the protector, that the warranty does NOT apply to a warranty replacement item. So that means, if you've swapped out your initial purchase with a warranty item, you'll have to purchase a brand new screen protector to get a lifetime warranty again. That is pretty standard across most things like this, so I have no complaints.
Here is the gold colored one that I ordered and installed since she has a gold S7:
https://www.amazon.com/gp/product/B01CUKZ296/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
iBolski said:
My wife just upgraded to an S7 (tried the Moto Z and it was too big, bulky and heavy for her). She wanted a tempered glass screen protector, but not like the one I have (which doesn't cover the entire screen due to the curved edges of the S7).
After much research, I found the amFilm glass protector was one that was listed in many top-10 lists as being excellent. This covers the entire glass but gives room on the edges for cases. My wife has a Speck Candyshell case for her phone and the screen protector works fine with it. My only issue with it is that on the top and bottom (which is fully protected), it's colored. So you can to choose the correct color based on your phone (black or gold). I don't understand why it has to be colored. Why not make it all clear so you can see the actual color of the phone? But it DOES cover the entire screen unlike the earlier brands that came out. And it was very easy to apply and there are no bubbles at all. Touch response is excellent from what I could tell. I tested it and couldn't find any "soft" or "blind" spots that didn't react and I just lightly touched, so it was pretty good. I'll wait and see how it goes with my wife after she's had it for awhile. It also comes with a lifetime warranty for the purchased product. That means, and they state this in the documentation that comes with the protector, that the warranty does NOT apply to a warranty replacement item. So that means, if you've swapped out your initial purchase with a warranty item, you'll have to purchase a brand new screen protector to get a lifetime warranty again. That is pretty standard across most things like this, so I have no complaints.
Here is the gold colored one that I ordered and installed since she has a gold S7:
https://www.amazon.com/gp/product/B01CUKZ296/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Click to expand...
Click to collapse
Thanks for such a detailed review. There are many protector glasses of that sort available in India, all of them are manufactured in china, but not the brand which you have mentioned. The reviews of the chinese one's is pathetic. So, I didn't go for them. Can you please check and confirm whether the phone fits fine in Gear Vr with the protector that you have installed or not?
This one, though its for the Edge model, looks tempting but I will wait for an early bird's review before ordering the one for the non-Edge version which should be available by tomorrow-
http://www.amazon.in/CEDO-Samsung-G...ems&ie=UTF8&qid=1489471980&sr=1-4&keywords=s7
I would urge you to ditch the plastic screen protector that is provided with the phone and get a premium tampered glass protector. Not only does it make the screen view much better, as well it makes handling the phone much easier, and something this phone deserves.
have you any photos of this tempered glass on P10?
Just google "Olixar Huawei P10 Tempered Glass Screen Protector".
Although it left 2-3 mm bubbles around the edges of the whole phone, which isn't nice, the bubbles looks like grey dirt, and I can't remove these bubbles. Might be looking for another brand like Zagg or something equivalent.
nicoX said:
Just google "Olixar Huawei P10 Tempered Glass Screen Protector".
Although it left 2-3 mm bubbles around the edges of the whole phone, which isn't nice, the bubbles looks like grey dirt, and I can't remove these bubbles. Might be looking for another brand like Zagg or something equivalent.
Click to expand...
Click to collapse
These bubbles are the cause why I don't replace the screen foil ^^
I use an screen protector like i posted in the oleophobic thread. No bubbles or anything here. But i don't know if it is sold somewhere outside the Netherlands.
I think these manufacture has improved over these years in producing protectors for curved glass, probably the latest trend is a normal glass protector and they include a tube of liquid adhesive to squeeze along the edge to cover the gaps, I check a few out to try, although they are not available for purchase out of hong kong or china, so I cannot provide a link, but I think places like ebay or amazon will have them available but at a much increased priced.
@ the ops, I too removed the protector, the supplied one is a good quality one, but I had a speck of dust underneath, and wasn't sure if it was dust or bright pixel. I just used one of my Sony XP protector and cut to shape for now untill I get a proper one.
Any suggestions which company do good on the p10?
I've tried two brands.
LK branded glass screen protector from Amazon UK. The fit was good, the black border blended in perfectly on my P10 black. But there was a big rainbow patch in the middle. I complained, the service was excellent, got a replacement no questions asked. But the new one also had a rainbow patch, even bigger!
Then I gave up and ordered a different one. An OMOTON branded one, also from Amazon. This one was all transparent glass, no gaps around the sides, and covers the whole screen width. It's a little short, ending with a gap at the top and bottom of the phone. However, the screen is so smooth to tap, and the brightness and colours so much better than the LK protector.
So I would recommend the OMOTON. It doesn't offer full protection, but I pair it with a simple tpu case with a lip, and it works quite well together.
Thanks for the help. Tomorrow a PULESEN, (via Amazon) will arive. If it is not that good, I go for your recommendation.
I ordered a GlasRitter protector by tradelis via eBay Germany.
It doesn't fit perfectly - the hole for the home button is around 1mm too low.
Also the glass looks like a mirror. When I'm outside at sunny weather it's really annoying and when I'm in the dark with a small light source, like a bed light, I can see myself.
So, don't buy this - it's oleophobic, but the rest isn't that good.
But it's the only one I found which covers the whole screen including the small area under the home button. Without this I don't want a protector. I need a full protector. Any recommendations?
After killing the first one of PULESEN with dust, I was able to figure out how to place the second one. It was not that easy but currently I am satisified.
Just received my case included is a screen protector and some goodies you can check the pictures. All for the price of 14 RMB. I bought it from JD.com in China. It took 11 days until I received my order because they were waiting for orders to start manufacturing the case since it's still a new phone.
Link to the store: https://item.m.jd.com/product/40266...are&utm_campaign=t_335139774&utm_term=CopyURL
After a successful application. Thanks to God Almighty.
Looking Good
Any news for a back skin transparent or otherwise,
From the likes of skinomi & illumi aqua sheild?
Rashad83 said:
Just received my case included is a screen protector and some goodies you can check the pictures. All for the price of 14 RMB. I bought it from JD.com in China. It took 11 days until I received my order because they were waiting for orders to start manufacturing the case since it's still a new phone.
Click to expand...
Click to collapse
Dentist.M.Evy said:
Looking Good
Any news for a back skin transparent or otherwise,
From the likes of skinomi & illumi aqua sheild?
Click to expand...
Click to collapse
Regarding a back skin I am not aware of any sold in China probably outside of it maybe yeah. The only cases that were available for the 1st generation ROG were only these type of TPU cases. I hope it's not the same case for the ROG 2. So far the only cases you can find for the ROG 2 are the TPU and book cover types.
Can you still use the air triggers with this case?
Cammarratta said:
Can you still use the air triggers with this case?
Click to expand...
Click to collapse
Looks like there are cutouts for them
Cammarratta said:
Can you still use the air triggers with this case?
Click to expand...
Click to collapse
Yes there is a cut out for air triggers and side USB. I can use the air triggers but not comfortably, if you use them too much I would suggest using the plastic case included with phone instead.You can check the cut outs from the pictures attached.
I bought a TPU Case and Tempered Glass screen protector off eBay (both came from the same seller) for my ROG Phone 2 (Tencent 8GB/128GB model), so I thought I'd share my thoughts on them.
Case ($10.89): Ultra Thin Soft Silicone Case For ASUS Rog Phone 2 ZS660KL Shockproof Back Cover
Screen Protector ($14.89): Nillkin CP+Pro Tempered Glass Full Screen Protector For ASUS ROG Phone 2 ZS660KL
I love both items!
The case is probably one of the best TPU cases available for the ROG Phone 2 at the moment. All ports are accessible, everything lines up properly, Air Triggers still work great, it has a nice 0.3mm raised lip around the screen to help protect it. Overall, nothing really bad to say about the case, other than maybe the "Soft Silicone" part of the name is a bit misleading as its not like super soft rubber or anything like that. Its flexible before inserting the phone, but I wouldn't really call it soft silicone. Still though, its a great case and I feel the phone is protected from small accidental drops now (definitely more-so than the stock clear hard plastic case that comes with it)!
The Tempered Glass screen protector is also great. The fingerprint sensor still works just fine, Its easy to apply, it can be lifted and re-positioned if you don't get it on perfect the first time. I was worried about the black borders around this particular screen protector when I first bought it, but everything lines up perfectly and doesn't appear to be covering or blocking anything when positioned correctly on the screen!
Edit: ok so even when installed perfectly, the black borders on the sides of the screen protector do block a tiny bit of the screen when viewed straight on... But it is tiny, like maybe 5 or 10 pixels on each side of the screen. You really gotta be looking for it to notice it though.
Edit2: so it also seems there is a very slight decrease in touch screen sensitivity with the tempered glass screen protector installed. After using it for awhile I noticed very occasionally it wouldn't register my input and I'd have to tap again. HOWEVER, this phone is so awesome, it has a built in way to solve this issue. Just go into the settings, then Advanced, scroll to the bottom and enable Glove Mode! It's meant to increases the touch screen sensitivity while wearing gloves, obviously, but works well to fix this minor issue as well.
bluegizmo83 said:
I bought a TPU Case and Tempered Glass screen protector off eBay (both came from the same seller) for my ROG Phone 2 (Tencent 8GB/128GB model), so I thought I'd share my thoughts on them.
Case ($10.89): Ultra Thin Soft Silicone Case For ASUS Rog Phone 2 ZS660KL Shockproof Back Cover
Screen Protector ($14.89): Nillkin CP+Pro Tempered Glass Full Screen Protector For ASUS ROG Phone 2 ZS660KL
I love both items!
The case is probably one of the best TPU cases available for the ROG Phone 2 at the moment. All ports are accessible, everything lines up properly, Air Triggers still work great, it has a nice 0.3mm raised lip around the screen to help protect it. Overall, nothing really bad to say about the case, other than maybe the "Soft Silicone" part of the name is a bit misleading as its not like super soft rubber or anything like that. Its flexible before inserting the phone, but I wouldn't really call it soft silicone. Still though, its a great case and I feel the phone is protected from small accidental drops now (definitely more-so than the stock clear hard plastic case that comes with it)!
The Tempered Glass screen protector is also great. The fingerprint sensor still works just fine, Its easy to apply, it can be lifted and re-positioned if you don't get it on perfect the first time. I was worried about the black borders around this particular screen protector when I first bought it, but everything lines up perfectly and doesn't appear to be covering or blocking anything when positioned correctly on the screen!
Edit: ok so even when installed perfectly, the black borders on the sides of the screen protector do block a tiny bit of the screen when viewed straight on... But it is tiny, like maybe 5 or 10 pixels on each side of the screen. You really gotta be looking for it to notice it though.
Edit2: so it also seems there is a very slight decrease in touch screen sensitivity with the tempered glass screen protector installed. After using it for awhile I noticed very occasionally it wouldn't register my input and I'd have to tap again. HOWEVER, this phone is so awesome, it has a built in way to solve this issue. Just go into the settings, then Advanced, scroll to the bottom and enable Glove Mode! It's meant to increases the touch screen sensitivity while wearing gloves, obviously, but works well to fix this minor issue as well.
Click to expand...
Click to collapse
Good tip on using glove mode when you use a tempered glass screen protector. Thanks!
Hi,
Stumbled on this Android Central article for Asus ROG phone 2 cases - Link
The first one mentioned as the staff pick looks promising.
Found the similar one on AliExpress - Link
Has anyone bought this TPU case, If yes can you give feedback or share images
qwertymk16i said:
Hi,
Stumbled on this Android Central article for Asus ROG phone 2 cases - Link
The first one mentioned as the staff pick looks promising.
Found the similar one on AliExpress - Link
Has anyone bought this TPU case, If yes can you give feedback or share images
Click to expand...
Click to collapse
I have that staff pick case, bought it on eBay. Reviewed it and a screen protector here : https://forum.xda-developers.com/rog-phone-2/accessories/tpu-case-screen-protector-ebay-t3968465
bluegizmo83 said:
I have that staff pick case, bought it on eBay. Reviewed it and a screen protector here : https://forum.xda-developers.com/rog-phone-2/accessories/tpu-case-screen-protector-ebay-t3968465
Click to expand...
Click to collapse
I've also ordered the nillkin CP+Pro tempered glass.
Have been using their tempered glasses for years. They are the best.
Can you also share images from bottom and top of the cover with phone?? And how much thickness does this cover add to the phone?
Also does it create issues in heat dissipation?
Thanks
qwertymk16i said:
I've also ordered the nillkin CP+Pro tempered glass.
Have been using their tempered glasses for years. They are the best.
Can you also share images from bottom and top of the cover with phone?? And how much thickness does this cover add to the phone?
Also does it create issues in heat dissipation?
Thanks
Click to expand...
Click to collapse
Including the 0.3mm raised lip around the phones screen, this case adds a total of 2.5mm of thickness and 3mm of width to the phone.
Measuring with my digital calipers, the phone without a case is 9.5mm thick and 78mm wide (not including the slight camera bump or the phones buttons). With the case on it measured 12mm thick and 81mm wide.
Heat dissipation is still excellent. I haven't noticed any change at all in temperatures.
I've looked everywhere but its nowhere to be found, can anyone guides me as to where I can get a good tpu case?
International vendors ship to india but delivery dates are no less than 30 days after I order.
Hi,
No TPU case present in India as of yet.
I have bought the one described in this thread - link
The units sold is very less in comparison to other brands like oneplus that is why you don't see recognised brands like spigen, otterbox or ringke creating a case for this phone.
Your best bet is to place an order on Aliexpress or Amazon.com.
Though sellers will be shipping cases from china only.
Please share if you find out some other good case?
Also look at these cases available as of now - Link
bluegizmo83 said:
Including the 0.3mm raised lip around the phones screen, this case adds a total of 2.5mm of thickness and 3mm of width to the phone.
Measuring with my digital calipers, the phone without a case is 9.5mm thick and 78mm wide (not including the slight camera bump or the phones buttons). With the case on it measured 12mm thick and 81mm wide.
Heat dissipation is still excellent. I haven't noticed any change at all in temperatures.
Click to expand...
Click to collapse
Thanks for the reply, I guess you indulge in DIY projects (measuring the dimensions using digital calipers :laugh
Do you play games on this phone? Do you observe noticeable increase in temp with the cover placed?
qwertymk16i said:
Thanks for the reply, I guess you indulge in DIY projects (measuring the dimensions using digital calipers :laugh
Do you play games on this phone? Do you observe noticeable increase in temp with the cover placed?
Click to expand...
Click to collapse
Lol yup lots of DIY and 3D Printing stuff.
I play lots of games on it via emulators, and some native gaming with PUBG and the new COD Mobile. No noticable temp increases.
This one is out of this world LOL!
https://www.ebay.com/itm/ZIMON-Alum...36373735?_trkparms=ispr=1&hash=item3b37a113e7
jkeener88 said:
This one is out of this world LOL!
https://www.ebay.com/itm/ZIMON-Alum...36373735?_trkparms=ispr=1&hash=item3b37a113e7
Click to expand...
Click to collapse
I wonder how that aluminum will change reception...
i ordered imak mate/sand feel case
its 0.1mm above the screen protector but it have air bags and not slipery as transperent ones sides are more loose then the silicone transperent case
i also ordered the this fist case from android central lets see how its hold
who have best oleophobic coating on the glass?
I had S20 for about 6 months and today I've been unlucky enough to somehow get dust under the protector and I had to peel it off.
I've been happy with it but I sadly found out that Samsung doesn't sell (or apply) the exact same screen protector in their stores so I'm looking for a replacement that will provide the most similar experience to the one that was originally applied on the screen.
Note: I do NOT want a glass screen protector. If there's a foil that will work as good or better than the pre-applied one, that's fine but a glass screen protector is something I'm not interested in.
Yep, I agree with you, their included protector is just great! I read that they do it in their stores, but that was while ago.... I'd be interested in similar protector as well since mine has some scratches and bubbles
I got some of these. Easy to apply (they give you all the tools) and is basically the same as the OEM one in terms of performance and aesthetics. Just read the installation booklet before you dive in as it's like a two part thing with a squeegee tool.
apiker [4 Pack] Compatible for Samsung Galaxy S20 Plus/S20+ Screen Protector, Soft TPU S20 Plus Screen Protector Film [Support Fingerprint Sensor] [Case Friendly] [Maximum Coverage][Bubble free]: Amazon.co.uk: Electronics & Photo
Free delivery and returns on eligible orders. Buy apiker [4 Pack] Compatible for Samsung Galaxy S20 Plus/S20+ Screen Protector, Soft TPU S20 Plus Screen Protector Film [Support Fingerprint Sensor] [Case Friendly] [Maximum Coverage][Bubble free] at Amazon UK.
www.amazon.co.uk
So I did but the one you suggested and I'm generally happy, the application I've done wasn't perfect (I applied the foil slightly to the left but other than that, it is aligned) but I do agree that it was quite easy to apply.
So onto differences from the OEM one.
There is no hole for the camera which I'm not sure is bad since I don't really use front camera and can't say if it affects the quality. For me it's probably a benefit because it would drive me mad if the hole were misaligned because of my imperfect application
Sadly, the foil is "softer" - if I grab the phone in wrong way and my fingernails put too much force towards the screen, it does leave marks (scratches, I guess). They don't seem to actually stay there for long but I don't feel as comfortable knowing that I can scratch it that easily. Even though I don't expect to change this foil to anything else, the OEM was definitely better on that front.
I don't really have much else to say here, for the price (I bought 3-pack for an equivalent of 13-14$) it's great but if I would be looking for the best foil out there (and had money to waste on all the different foils ), I would definitely keep looking for a better one.
Ibywind. Best of the best.
jack1142 said:
I had S20 for about 6 months and today I've been unlucky enough to somehow get dust under the protector and I had to peel it off.
I've been happy with it but I sadly found out that Samsung doesn't sell (or apply) the exact same screen protector in their stores so I'm looking for a replacement that will provide the most similar experience to the one that was originally applied on the screen.
Note: I do NOT want a glass screen protector. If there's a foil that will work as good or better than the pre-applied one, that's fine but a glass screen protector is something I'm not interested in.
Click to expand...
Click to collapse
I had the same problem with my S20; I tried different tempers but nothing worked, then I tried gadgetshieldz screen skins, which were recommended by a colleague. I've been using it for three months and am pleased with it.
In my perception, you may like that because the display skin is ultra-thin.
Am leaving the link which I ordered on: Samsung s20