trying to unbrick huawei gr3 help! - Android Q&A, Help & Troubleshooting

hello i bricked my gr3 and now i am tring to unbrick it with sp flash tool installed every driver and there is no problem with drivers just when sp flash tool starts downloading it get stuck on AD 100% and after 10seconds it says error 2004 help plz

Gigageo said:
hello i bricked my gr3 and now i am tring to unbrick it with sp flash tool installed every driver and there is no problem with drivers just when sp flash tool starts downloading it get stuck on AD 100% and after 10seconds it says error 2004 help plz
Click to expand...
Click to collapse
Hi , did you try with other version of SPFT like this one ?
https://www.youtube.com/watch?v=9sly6LGIB0c
Try to disable driver signature , Run As Administrator and disable your Antivirus also and try. Good luck

Teddy Lo said:
Hi , did you try with other version of SPFT like this one ?
https://www.youtube.com/watch?v=9sly6LGIB0c
Try to disable driver signature , Run As Administrator and disable your Antivirus also and try. Good luck
Click to expand...
Click to collapse
Yes i tryed that too diffrent sp flash tools and driver signature disabled and runs as administrator i reinstalled drivers multiple times abd they all are working i tried everything i could imagine

Gigageo said:
Yes i tryed that too diffrent sp flash tools and driver signature disabled and runs as administrator i reinstalled drivers multiple times abd they all are working i tried everything i could imagine
Click to expand...
Click to collapse
1. Try another USB Port.
2. Lunch SP Flash again as admin.
3. Try another PC.
4. Check that the battery in the device is charged.
5. Try with diferent usb cable
6. Try another firmware

Teddy Lo said:
1. Try another USB Port.
2. Lunch SP Flash again as admin.
3. Try another PC.
4. Check that the battery in the device is charged.
5. Try with diferent usb cable
6. Try another firmware
Click to expand...
Click to collapse
well i tried everything but there is problem with step 5
i know that my battary is charging but when it gets enough power to start the phone it starts and instantly shut downs and this heppens every time i instert micro usb in but when i press buttuns it goes to meta mod (i think because i can see device with mtk drivers) and when i try to flash stock rom in sp flash tool it gets stuck on da 100% and i get error 2004

also i bricked my phone when i flashed u-boot.img as boot in twrp does that has to do something about sp flash tool or enything?

Gigageo said:
well i tried everything but there is problem with step 5
i know that my battary is charging but when it gets enough power to start the phone it starts and instantly shut downs and this heppens every time i instert micro usb in but when i press buttuns it goes to meta mod (i think because i can see device with mtk drivers) and when i try to flash stock rom in sp flash tool it gets stuck on da 100% and i get error 2004
Click to expand...
Click to collapse
Try again to flash latest stock firmware but not just keep holding Power button during flashing with SP flash tool , you can try also Beta Version of SP Flash tool .

Teddy Lo said:
Try again to flash latest stock firmware but not just keep holding Power button during flashing with SP flash tool , you can try also Beta Version of SP Flash tool .
Click to expand...
Click to collapse
Well i found only one firmware for my phone with proper scatter and i am using that and beta versions is not working too

Look here and try with sd update .
http://huawei-firmware.com/phone-list/huawei-gr3

Teddy Lo said:
Look here and try with sd update .
http://huawei-firmware.com/phone-list/huawei-gr3
Click to expand...
Click to collapse
nvm i fixed it i dissasmbled phone and removed battary wire then it installed
thank you for response

Related

[Q] Help!!!!!!!!

:crying: Guys , my SP Flash Tool keep stucking at "100%RedBar" and "0%" . I can't flash anything... :crying: Help me pls...
tngultimate said:
:crying: Guys , my SP Flash Tool keep stucking at "100%RedBar" and "0%" . I can't flash anything... :crying: Help me pls...
Click to expand...
Click to collapse
What are tryng to flash?
Sent from my Lenovo P780
stympy said:
What are tryng to flash?
Sent from my Lenovo P780
Click to expand...
Click to collapse
Lenovo P780 stock rom s124
tngultimate said:
Lenovo P780 stock rom s124
Click to expand...
Click to collapse
Use spflash tool 5 not 3. In spflash tool 5 select firmware upgrade not download.
Try and tel me if works.
Sent from my Lenovo P780
stympy said:
Use spflash tool 5 not 3. In spflash tool 5 select firmware upgrade not download.
Try and tel me if works.
Sent from my Lenovo P780
Click to expand...
Click to collapse
It keep saying "Unrecognized Rom" detected
tngultimate said:
It keep saying "Unrecognized Rom" detected
Click to expand...
Click to collapse
Soo.. Sp flash tool 3 is telling you the same thing ?
Sent from my Lenovo P780
stympy said:
Soo.. Sp flash tool 3 is telling you the same thing ?
Sent from my Lenovo P780
Click to expand...
Click to collapse
sp flash tool 3 just stuck at red bar or 0 %...
tngultimate said:
sp flash tool 3 just stuck at red bar or 0 %...
Click to expand...
Click to collapse
Use spflash tool 3 open the back of your phone and press the red button on your right for 20 secconds after yo pressed firmware upgrade button abd pluged your cable.
Sent from my Lenovo P780
stympy said:
Use spflash tool 3 open the back of your phone and press the red button on your right for 20 secconds after yo pressed firmware upgrade button abd pluged your cable.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Also stuck at 0% ... but the time keep increasing . After 40 seconds , it appear a message says
BROM ERROR : S_FT_READBACK_FAIL (4009)
tngultimate said:
Also stuck at 0% ... but the time keep increasing . After 40 seconds , it appear a message says
BROM ERROR : S_FT_READBACK_FAIL (4009)
Click to expand...
Click to collapse
Hi. Lets try this: since "Firmware Upgrade" or "Download" option dont work, first "Format---->Auto Format Whole NAND flash", then flash ROM using "Download" option with "DA/DL all" selected !!!
Tell me if works.
stympy said:
Hi. Lets try this: since "Firmware Upgrade" or "Download" option dont work, first "Format---->Auto Format Whole NAND flash", then flash ROM using "Download" option with "DA/DL all" selected !!!
Tell me if works.
Click to expand...
Click to collapse
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
tngultimate said:
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
Click to expand...
Click to collapse
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
stympy said:
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
Click to expand...
Click to collapse
I have the exact same issue. Flashing stock S124 after (rooted) S223 with SpTools messes something up.
I managed to do a TWRP restore to go back to S221 but I can't use SpTools anymore.
I get the same SpTools error message. Only after pressing the red reset button my phone will then come back to life.
stympy said:
Follow this steps:
1. Go to My computer>Right Click> Properties> Device manager>Universal Serial Bus Controller
2. Now plug the cable in your device.
3. Tell me what appears there.
Click to expand...
Click to collapse
Nothing happen...
londondutch said:
I have the exact same issue. Flashing stock S124 after (rooted) S223 with SpTools messes something up.
I managed to do a TWRP restore to go back to S221 but I can't use SpTools anymore.
I get the same SpTools error message. Only after pressing the red reset button my phone will then come back to life.
Click to expand...
Click to collapse
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
---------- Post added at 03:58 PM ---------- Previous post was at 03:57 PM ----------
tngultimate said:
My phone now doesn't detected by my computer... It can connect to computer yesterday... Now my phone just charging when connect to computer... Save me please :crying::crying:
Click to expand...
Click to collapse
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
stympy said:
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
---------- Post added at 03:58 PM ---------- Previous post was at 03:57 PM ----------
Your preloader seems to be messet up. I have one problem the same like yours yesterday. It took like 4 hours to solve the problem. The problem was like this:
The computer was not recognizing the phone when the phone was powered off. Sooo.. what i did: i opened device manager in the computer, then i attached the phone. Something new has appeared in the device manager for a seccond. I clicked fast on it. A small window hass appeared. From this step i was safe. I just updated the driver and that wass it. I could flash the ROM i wanted.
Hope this helps you.
Click to expand...
Click to collapse
Thanks for your explanation, you seem to be the absolute guru on this site for this device! I think you are right about the preloader being messed up. I tried to install the USB driver (again) for the new device that the computer now sees. It is listed in the device manager as "Unknown Device" under USB controllers. I can't seem to force it to accept new USB drivers for it (Lenovo drivers). It keeps saying that the driver is not compatible with the device. I use Win 7 64bit, could that have something to do with it? Also is it possible to flash a new preloader using TWRP? If I press the reset button on my phone it reboots fine (rooted S221) and I have TWRP installed.
londondutch said:
Thanks for your explanation, you seem to be the absolute guru on this site for this device! I think you are right about the preloader being messed up. I tried to install the USB driver (again) for the new device that the computer now sees. It is listed in the device manager as "Unknown Device" under USB controllers. I can't seem to force it to accept new USB drivers for it (Lenovo drivers). It keeps saying that the driver is not compatible with the device. I use Win 7 64bit, could that have something to do with it? Also is it possible to flash a new preloader using TWRP? If I press the reset button on my phone it reboots fine (rooted S221) and I have TWRP installed.
Click to expand...
Click to collapse
Here are the drivers i use! Hope this will help you!
Soo.. i never tried to flash preloader from TWRP. Thats an ideea, but you have to do a full backup of your phone... i think...
When i have preloader problems i flash again the whole ROM. I think is safer, better... and wize.
stympy said:
Here are the drivers i use! Hope this will help you!
Soo.. i never tried to flash preloader from TWRP. Thats an ideea, but you have to do a full backup of your phone... i think...
When i have preloader problems i flash again the whole ROM. I think is safer, better... and wize.
Click to expand...
Click to collapse
Thanks for the drivers, I am still struggling to make this "Unknown Device" accept other drivers. What was your unrecognised phone called in Device Manager? Was it also "Unknown Device" in the USB section?
londondutch said:
Thanks for the drivers, I am still struggling to make this "Unknown Device" accept other drivers. What was your unrecognised phone called in Device Manager? Was it also "Unknown Device" in the USB section?
Click to expand...
Click to collapse
Hi. The think was someting like this:
First i installed the .exe file. Reboot PC.
2. I have plugged the phone to the PC and new hardware wizard has appeared.
3. Now i have powered of the phone.
4. Again i have plugged the phone this time powered off.
5. At this time in Device Manager appeared for a second or two not in USB area something with.. MTK65...
6. Click very fast on it because that will desapear very fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
Sent from my Lenovo P780
stympy said:
Hi. The think was someting like this:
First i installed the .exe file. Reboot PC.
2. I have plugged the phone to the PC and new hardware wizard has appeared.
3. Now i have powered of the phone.
4. Again i have plugged the phone this time powered off.
5. At this time in Device Manager appeared for a second or two not in USB area something with.. MTK65...
6. Click very fast on it because that will desapear very fast.
7. After you clicked on it all you have to do is update driver, and voila you have drivers installed and now all you have to do is to flash you ROM.
Hope this will help you.
Good luck.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Thanks !!! ^^ Finally I won !!! You are like the proffesion in P780 !!! Stympy , another thing i want to ask you , how to root S223 the rom that you give ? I saw there was an alternative scatter in your S223 .

Lenovo P780 SoftBrick

Hey Guys
I bricked my P780 and didnt do a backup. I formated the phone with SpFlashTool, afterwards the Flashing didnt work. And a second format didnt work too.
Now i tried nearly every possible tutorial on the web...
I am using win7
My main problem is that i am using SpFlashTool (newest version) and i get an 4032 Error if i try to download the rom.
I tried nearly every Rom for the p780 with every possible scatter file.
I tried nearly every MediaTek DA VCOM USB Driver, MediaTek PreLoader VCOM USB Driver and MTK USB Port Driver and always with no success.
I even plugged out the battery (its not removable) without damaging the phone...
Spackotus said:
Hey Guys
I bricked my P780 and didnt do a backup. I formated the phone with SpFlashTool, afterwards the Flashing didnt work. And a second format didnt work too.
Now i tried nearly every possible tutorial on the web...
I am using win7
My main problem is that i am using SpFlashTool (newest version) and i get an 4032 Error if i try to download the rom.
I tried nearly every Rom for the p780 with every possible scatter file.
I tried nearly every MediaTek DA VCOM USB Driver, MediaTek PreLoader VCOM USB Driver and MTK USB Port Driver and always with no success.
I even plugged out the battery (its not removable) without damaging the phone...
Click to expand...
Click to collapse
Hi. Because you have formated your nand you must reinstall your drivers, because your preloader now is messed up.
In order to do that you must do this:
1. Install drivers.
2. Go to device manager and let the window open.
3. Connect your phone and new hardware should appear for just a seccond or 2 max, something with MTK 6.5.XXX.
4. Click very fast on the little new thing that appear there because will desapear.
5. Now press the button to update drivers hardware. In one of my posts you will find an archive with the right drivers. Drivers are on the archive uploaded here.
6. After the drivers are installed your PC should recognize the phone.
7. After this the steps should be the same to flash your ROM. Oh and by the way: Press Firmware Upgrade button not Download. And dont forget to check DA/DL With Checksum... option
8. Waiting for feedback.
9. Good Luck.
stympy said:
Hi. Because you have formated your nand you must reinstall your drivers, because your preloader now is messed up.
In order to do that you must do this:
1. Install drivers.
2. Go to device manager and let the window open.
3. Connect your phone and new hardware should appear for just a seccond or 2 max, something with MTK 6.5.XXX.
4. Click very fast on the little new thing that appear there because will desapear.
5. Now press the button to update drivers hardware. In one of my posts you will find an archive with the right drivers. Drivers are on the archive uploaded here.
6. After the drivers are installed your PC should recognize the phone.
7. After this the steps should be the same to flash your ROM. Oh and by the way: Press Firmware Upgrade button not Download. And dont forget to check DA/DL With Checksum... option
8. Waiting for feedback.
9. Good Luck.
Click to expand...
Click to collapse
First of all thanx!
But whitch driver i should install in Point 1. ?
Second, what should i do if the device is appearing for 2 sec, the device appears straight as unknown device and then replugs itself every 30 sec
Spackotus said:
First of all thanx!
But whitch driver i should install in Point 1. ?
Second, what should i do if the device is appearing for 2 sec, the device appears straight as unknown device and then replugs itself every 30 sec
Click to expand...
Click to collapse
Hi. The drivers i uploaded to you at my post!
For the new device you must have the device manager window open ! Only there you will find the preloader.
stympy said:
Hi. The drivers i uploaded to you at my post!
For the new device you must have the device manager window open ! Only there you will find the preloader.
Click to expand...
Click to collapse
Well the device appears straight as MTK USB Port, , there is no 2 sec TimeFrame when the device apears as MT65xx
an yes, i installed your driver, i am even using a new installation of win7
Hi guys.. sory to butt in... but im experiencing the same problem where in my case i have lenovo s720 instead.
Does the solution works for u?? Mine says something about partition manager eror.
beckham_totti said:
Hi guys.. sory to butt in... but im experiencing the same problem where in my case i have lenovo s720 instead.
Does the solution works for u?? Mine says something about partition manager eror.
Click to expand...
Click to collapse
The solution should work for you! Or else search on this forum itself and you will get your answer!

Help with unbricking

Hello,
I flashed a ROM with sp-tool but the phone does not open. I power it on but nothing happens, no vibration, no screen flashing nothing.
Now I try to reflash the stock ROM but:
If I connect it it to PC it is recognized as MTK USB Port instead of MediaTek Preloader USB VCOM and SPTools returns DRAM failed error.
I tried removing the battery and connecting it, pressing VOL+ etc but the same happens.
I read this guide http://forum.xda-developers.com/showthread.php?t=1943442 but I could not do something. I found in the guide a link in a Russian forum where they talked about flashing the preloader using the board's PINs, but the translate does not give me quality information on how to do this
Any ideas?
Thank you
ShadowReaperGR said:
Hello,
I flashed a ROM with sp-tool but the phone does not open. I power it on but nothing happens, no vibration, no screen flashing nothing.
Now I try to reflash the stock ROM but:
If I connect it it to PC it is recognized as MTK USB Port instead of MediaTek Preloader USB VCOM and SPTools returns DRAM failed error.
I tried removing the battery and connecting it, pressing VOL+ etc but the same happens.
I read this guide http://forum.xda-developers.com/showthread.php?t=1943442 but I could not do something. I found in the guide a link in a Russian forum where they talked about flashing the preloader using the board's PINs, but the translate does not give me quality information on how to do this
Any ideas?
Thank you
Click to expand...
Click to collapse
Hi. What you did is to brick your preloader. It seems to me that your phone is made after 03.2014.
What you have to do is:
1. reinstall the driver. Follow the tutorial from here: http://forum.xda-developers.com/lenovo-p780/help/lenovo-p780-mt6589-device-hard-bricked-t2890675
2. download the good preloader from here: http://forum.xda-developers.com/len...cked-flashing-wrong-rom-doesnt-t2749683/page4
3. replace the preloader from your downloaded ROM with the one from step 2.
4. Start SP FLASH TOOL and load scatter file
5. Check DA/DL WITH CHECKSUM
6. Flash it normaly now.
7. Good Luck
8. Waiting for feedback....
The same.
The phone is recognized as MTK USB Port and the SP-flash returns DRAM failed
ShadowReaperGR said:
The same.
The phone is recognized as MTK USB Port and the SP-flash returns DRAM failed
Click to expand...
Click to collapse
Hi. Can you tel me what was your STOCK ROM?
And what SP FLASH TOOL are you using ?
stympy said:
Hi. Can you tel me what was your STOCK ROM?
And what SP FLASH TOOL are you using ?
Click to expand...
Click to collapse
Merimobiles told me that this was the original rom
www.needrom.com/download/lenovo-p780-2
I tried varirous versions of SP Flash Tool
I think that the only option is to hard-flash it using the pins from the board
ShadowReaperGR said:
Merimobiles told me that this was the original rom
www.needrom.com/download/lenovo-p780-2
I tried varirous versions of SP Flash Tool
I think that the only option is to hard-flash it using the pins from the board
Click to expand...
Click to collapse
Try this: READ THIS TWICE TILL YOU UNDERSTAND :
1. Download SP FLASH 5
2. Download you ROM from here(not optional): http://forum.xda-developers.com/lenovo-p780/development/p780-row-s226-flash-flashtool-t2909202
3. Open Flash Tool 5 load scatter file from the ROM you downloaded.
4. Select only the preloader.
5. Under the big Download button select firmware upgrade
6. Now press BIG DOWNLOAD BUTTON.
7. The preeloader should flash.
8. Now after flashing the preloader you must check all others except preloader.
9. Under the big Download button select just download only.
10. Press BIG DOWNLOAD BUTTON.
11. Now your ROM should start downloading in your phone.
12. After downloading is completed your ROM should start .
13. Good Luck
14 Waiting for feedback.
wanna use ur method
Hi, I will try your method on my brick lenovo p780 4g. Wish me luck. Thanks.
:fingers-crossed::fingers-crossed::fingers-crossed:
alongbalbol said:
Hi, I will try your method on my brick lenovo p780 4g. Wish me luck. Thanks.
:fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
I wished on your original post !

My MT6582(mediatek) phone is Dead - Please help...

Hello
Every thing was good until I decided to port a ROM for my phone
I ported it with kitchen then flashed it via SP Flash Tools. The process completed without any error. After that I tried to turn on my phone but it didnt, and my phone was completely dead and now nothing is working(The screen is black,device doesnt charge,recovery doesnt come up and even dosent conect to PC) .
I tried this trick but it didnt work too
http://forum.xda-developers.com/showthread.php?t=1943442
Because PC can not recognize the phone and when I conect the cable to the computer nothing happens. I tried differnet keys but none of them worked
The port Rom was canvas A1 4.4.4 with an odd preloader and my phone is a chinces phone with mt6582 chip (GFIVE President Classic 9).
Is there any other way to revive this phone?
thanks
Ok first you wanna download your stock rom from needrom.com...then flash it with sp tools..if this doesnt work cause sp tools isnt regognising your phone,take out your phones battery and connect it pressing the vol down button(in case it is always disconnecting itself)..ok now, open sp flash tool,take the scatter file from the rom you just downloaded and extracted...press download,connect your phone without battery and you are done!!
Godlike12 said:
Ok first you wanna download your stock rom from needrom.com...then flash it with sp tools..if this doesnt work cause sp tools isnt regognising your phone,take out your phones battery and connect it pressing the vol down button(in case it is always disconnecting itself)..ok now, open sp flash tool,take the scatter file from the rom you just downloaded and extracted...press download,connect your phone without battery and you are done!!
Click to expand...
Click to collapse
As I said it doesnt work...
The PC can not recognize the phone therefore flashing is impossible...
What can I do?

help!! my redmi note 4 mtk Hardbrick

Help me guys.. My RN4 mtk 3/64 MIUI Global 8.0.3.0 unlockbootloader suddently dead.. No led, no vibrate. My pc detect as mtk usb port..but connection not stable
.. Connect-disconnect repeatly. And SPFT can't work.. Can't format, can't readback, can't flash.. Always stuck at 100% red bar and ERROR : STATUS_DA_HASH_MISMATCH for rom miui 8 china or global stable.. And ERROR : STATUS_EXCEED_NUM_MAX for rom global dev and china dev..please give me solution :crying::crying:
Thanks..
Can you get into the bootloader to use fastboot? Does that much work? If not, you may be in trouble
Also, are you positive you have the MTK driver installed correctly? I remember there being driver verification issues with Win10.
smokinjoe2122 said:
Can you get into the bootloader to use fastboot? Does that much work? If not, you may be in trouble
Also, are you positive you have the MTK driver installed correctly? I remember there being driver verification issues with Win10.
Click to expand...
Click to collapse
Can not enter fastboot or recovery mode .. I am using win 7 64bit .. And for the mtk driver I've tried to install repeatedly from various sources and in various ways but the result is the same.
arilevint said:
Help me guys.. My RN4 mtk 3/64 MIUI Global 8.0.3.0 unlockbootloader suddently dead.. No led, no vibrate. My pc detect as mtk usb port..but connection not stable
.. Connect-disconnect repeatly. And SPFT can't work.. Can't format, can't readback, can't flash.. Always stuck at 100% red bar and ERROR : STATUS_DA_HASH_MISMATCH for rom miui 8 china or global stable.. And ERROR : STATUS_EXCEED_NUM_MAX for rom global dev and china dev..please give me solution :crying::crying:
Thanks..
Click to expand...
Click to collapse
If your repeatedly getting disconnect/reconnect I would suggest you use another USB cable or USB port because that's not normal.
If not then it may be a driver/PC issue.
Sent from my Redmi Note 4 using Tapatalk
Wilderone said:
If your repeatedly getting disconnect/reconnect I would suggest you use another USB cable or USB port because that's not normal.
If not then it may be a driver issue.
Sent from my Redmi Note 4 using Tapatalk
Click to expand...
Click to collapse
Ok..I'm going to buy a new cable.
Still unresolved. I try memory test SPFT can run normally. Device manager detects as MediaTek DA vcom usb .. But if I format or flashing error message appears again .. STATUS_DA_HASH_MISMATCH.
Perhaps try downloading different firmware if you're getting a hash error?
I still think getting into fastboot is important...Since Official MIUI doesn't have a real recovery, you're better off installing TWRP and seeing if you can do something from within recovery.
arilevint said:
Still unresolved. I try memory test SPFT can run normally. Device manager detects as MediaTek DA vcom usb .. But if I format or flashing error message appears again .. STATUS_DA_HASH_MISMATCH.
Click to expand...
Click to collapse
Is your Rn4 a mtk device or snapdragon device???? Please check.
If it is mtk then u would require scatter file along with correct firmware.
And if it is a snapdragon device, u can flash most of the things through bootloader mode.
Hope it helps.
subodhverma21 said:
Is your Rn4 a mtk device or snapdragon device???? Please check.
If it is mtk then u would require scatter file along with correct firmware.
And if it is a snapdragon device, u can flash most of the things through bootloader mode.
Hope it helps.
Click to expand...
Click to collapse
Im sure my device xiaomi redmi note 4 mediatek 3/64gb with logo china mobile in back casing.
arilevint said:
Im sure my device xiaomi redmi note 4 mediatek 3/64gb with logo china mobile in back casing.
Click to expand...
Click to collapse
Working with MTK devices is bit tricky.
though you will get success, i Hope
If you are sure that your device is MTK, then ofcourse your bootloader mode will not work. So try to adopt this solution:
1. Get SPFlash Tool, the latest one. http://spflashtool.com/
2. Get MediaTek USB VCOM drivers. http://spflashtool.com/
3. Now most important Get your Original Firmware along with the Scatter file. The SPflashtool only recognizes the scatter file. So you need ROM along with scatter file.
check this link and follow the instructions http://en.miui.com/thread-370620-1-1.html
check your ROM if it is here. Only Use the correct firmware for your devices otherwise you may do a permanent damage to your device. http://en.miui.com/download-309.html#454
Hope it helps.
Hi i have the same problem, spft always give me an error, i cannot enter in fastboot or recovery, did you solve the problem?
have you flashed preloader or had you selected "Format all and Download"? If not, or maybe yes,, try to flash custom cust.img and just plug in your phone without holding vol-down button. Also make sure that you disable driver signature enforcement. Anyway it sounds scary as I reflash my fastboot firmware on SP Flash Tool ocasionally after using twrp.
---------- Post added at 06:14 PM ---------- Previous post was at 06:12 PM ----------
If it doesn't work,, have a motherboard replacement
hello i managed to flash with sp flash tool but after flashing it is not charging and couldnt be powered on. i have held the power button for more than 20 secs
jr1945 said:
hello i managed to flash with sp flash tool but after flashing it is not charging and couldnt be powered on. i have held the power button for more than 20 secs
Click to expand...
Click to collapse
go to help at care centre buddy it look like a serious problem
subodhverma21 said:
Working with MTK devices is bit tricky.
though you will get success, i Hope
If you are sure that your device is MTK, then ofcourse your bootloader mode will not work. So try to adopt this solution:
1. Get SPFlash Tool, the latest one.
2. Get MediaTek USB VCOM drivers.
3. Now most important Get your Original Firmware along with the Scatter file. The SPflashtool only recognizes the scatter file. So you need ROM along with scatter file.
check this link and follow the instructions
check your ROM if it is here. Only Use the correct firmware for your devices otherwise you may do a permanent damage to your device.
Hope it helps.
Click to expand...
Click to collapse
i stuck in (Vol -) ,( Vol - and power button )and plug in USB. red bar not appear in SP tool, why it happen? please help
chimouw said:
i stuck in (Vol -) ,( Vol - and power button )and plug in USB. red bar not appear in SP tool, why it happen? please help
Click to expand...
Click to collapse
are you able to go to VCOM mode?
you have to go to VCOM mode in the MTK device to use the SP Flash Tool.
1. Install Vcom drivers from internet.
2. Phone will get detected. Then the SP Flash Tool will Run
Hope it helps.
subodhverma21 said:
are you able to go to VCOM mode?
you have to go to VCOM mode in the MTK device to use the SP Flash Tool.
1. Install Vcom drivers from internet.
2. Phone will get detected. Then the SP Flash Tool will Run
Hope it helps.
Click to expand...
Click to collapse
I finally installed mediatek driver but it didn't give any progress, btw test point can work??
chimouw said:
I finally installed mediatek driver but it didn't give any progress, btw test point can work??
Click to expand...
Click to collapse
Do you have the scatter file?
where did you get the scatter file?
Which SPF tool are you working with?
Download the latest SPFT and then try.
hope it helps.
subodhverma21 said:
Do you have the scatter file?
where did you get the scatter file?
Which SPF tool are you working with?
Download the latest SPFT and then try.
hope it helps.
Click to expand...
Click to collapse
I has scatter file from en. Miui /a-234 with codename nikel, I used spf tool the latest version.
Otherwise, my phone can not detected in my pc, neither unknown device or Vcom statuse. How should I do again? With test point or DFC can work??
Really my phone is Deep Death, before DD I flashed with snap dragon rom, result is DD
chimouw said:
I has scatter file from en. Miui /a-234 with codename nikel, I used spf tool the latest version.
Otherwise, my phone can not detected in my pc, neither unknown device or Vcom statuse. How should I do again? With test point or DFC can work??
Really my phone is Deep Death, before DD I flashed with snap dragon rom, result is DD
Click to expand...
Click to collapse
Have patience, it should not be problem.
Is your battery removable?
If yes, take it out. Unplug usb.
Plug usb again with battery out. Press -vol to detect vcom driver.
Most important , adb driver or usb debugging mode should not be enabled. Otheewise the vcom drivers will not install.
Once vcom mode works. SPFT will work on its own.
Hope it helps.

Categories

Resources