Hello
I have an Lenovo s898t+ from aliexpress. with androdi 4.4.2 And I was trying to increase my file system root partition in phone. I use apk meteos MTK 6592, and after getting to recovery mode I did everithing like was write in other forumm that I found set factory restart. And now my phone is in something lie bootloop always showing android figure and when I try to turn it off only show
forrmating /data...
mount system/ error
and can`t get to recovery mode or if I try to connect to PC via USB without the batery inside the phone is still rebooting. I know how to flash stock rom, but cant do that becouse the phone is still connecting and disconnecting to PC.
Can somebody help please I have been searching for 4 days with no luck.
Thanks for all you answers
If your phone is a MTK device..
U can flash a new rom..
With SPflash tools..
abhinavp649 said:
If your phone is a MTK device..
U can flash a new rom..
With SPflash tools..
Click to expand...
Click to collapse
Cant get phone to stable connection to PC always reseting without battery and with baterry the bootloop shows up and did not connect to pc
u have to start the download process from SPtools before connecting your phone to PC
hopefully, it will show your phone..
some phones have a trigger to start the download..may be power button or any of volume buttons..
Some phone also required to pop in the battery to start the process..
Try any of these options..
hopefully, u will have ur phone flased with a new rom..
ingshibbby said:
Cant get phone to stable connection to PC always reseting without battery and with baterry the bootloop shows up and did not connect to pc
Click to expand...
Click to collapse
u have to start the download process from SPtools before connecting your phone to PC
hopefully, it will show your phone..
some phones have a trigger to start the download..may be power button or any of volume buttons..
Some phone also required to pop in the battery to start the process..
Try any of these options..
hopefully, u will have ur phone flased with a new rom..
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Once the red line loads, try putting back the battery. Sometimes the handset needs power from the battery. I did that with my HT3: once SP Flash Tool detected my phone, I put the battery back.
FLASHED 2.DUMP_ROM [SPFT][ROOTED] FROM All About CherryMobile Flare 4 AFTER IT SAYS FLASHING IS DONE 100% WITH CHECK MARK THEN MY PHONE DIDNT RESTART I WAITED FOR ABOUT 15 MINUTES TO SEE IF THERE'S SOMETHING MIGHT HAPPEN BUT NOTHING ONLY BLACK..
SO I PULLED THE USB CONNECTOR, THEN PLUG IT BACK. THE ONLY THING THAT I SAW IS UNRECOGNIZED USB. NO CHARGING LOGO OR ANDROID OR ANYTHING EVEN THE LED INDICATION OF CHARGING IS NOT BLINKING.
I HOPE SOMEONE CAN HELP ME :crying::crying::crying::crying::crying::crying::crying:
UP
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
AlexanderBabansky said:
I also had the same problem and I also cried. Your phone have MediaTek MT6753 Chipset. I have MT6582. You flashed ROM via recovery and looks like ROM have conflict with bootloader.
SP Flash Tool can flash shutdown MTK devices via USB. Your computer show "UNRECOGNIZED USB". SP Flash Tool need special ROM and driver to find your phone. Not sure, that SP Flash Tool can help you, but it helped me.
How I decided problem:
I waited some time (I went sleep, it was night)
Found stock ROM for Flashtool. This ROM contain all data for device and have more size.
Install driver for my phone.
Pulled out battery.
Connect with computer via USB.
Put in battery and computer detected phone as "MediatekDevice". SP Flash tool also detected phone
Started flashing.
Good luck!
Click to expand...
Click to collapse
thanks bro.
now it show dram fail (4032)
i was trying to flash stock rom to my infinix x551 by sp flashtool everything were great until i accidentally unplugged the phone
tried to retry to flash it again with no hope
it doesn`t open recovery mode or switching on
only when i plug it to the pc i hear a voice from it then nothing happens
Remove the battery and then try to plug the phone into sp flash tools
Adithya FRK said:
Remove the battery and then try to plug the phone into sp flash tools
Click to expand...
Click to collapse
my phone battery is built in i can`t remove it
Did you try to flash the bootloader at first? It is not recommended to do that.
Hi, i bought power 2, phone not open and noting happen when press power or vol+ - together + power, or ....try everything
Bricked when try flash twrp recovery. later i try flash rom again, my computer see phone when phone is closed. can not open already. But now my computer not see the phone:A request for the USB device descriptor failed.
What can i do, and sorry for my english
This phone can't be bricked (mostly). You can easily restore the stock firmware, just download stock rom from official site, extract it. And use sp flash tool not the one that comes with the official rom. Open sp flash tool.
Load scatter file from official rom, you can leave the DA file for all mtk phones that comes with stock rom or use the one in sp flash tool (just leave it as it is) in the user interface of sp flash tool.
Make sure it says "download only" from the drop box. Click download then connect the phone to your computer. Flashing will start and should take about 1 minute and 30 seconds to finish.
If flashing doesn't start. Make sure you have vcom drivers installed. (Also for flashing to start, phone must be turned off obviously, but since you have semi brick, you don't have to worry about that).
Rebel_X said:
This phone can't be bricked (mostly). You can easily restore the stock firmware, just download stock rom from official site, extract it. And use sp flash tool not the one that comes with the official rom. Open sp flash tool.
Load scatter file from official rom, you can leave the DA file for all mtk phones that comes with stock rom or use the one in sp flash tool (just leave it as it is) in the user interface of sp flash tool.
Make sure it says "download only" from the drop box. Click download then connect the phone to your computer. Flashing will start and should take about 1 minute and 30 seconds to finish.
If flashing doesn't start. Make sure you have vcom drivers installed. (Also for flashing to start, phone must be turned off obviously, but since you have semi brick, you don't have to worry about that).
Click to expand...
Click to collapse
Vdcom drivers already installed but not using. becouse computer does not see phone.
Unknown usb device . A request for the USB device descriptor failed. (code 43)
if i solve this, maybe i can flash rom
Rebel_X said:
This phone can't be bricked (mostly). You can easily restore the stock firmware, just download stock rom from official site, extract it. And use sp flash tool not the one that comes with the official rom. Open sp flash tool.
Load scatter file from official rom, you can leave the DA file for all mtk phones that comes with stock rom or use the one in sp flash tool (just leave it as it is) in the user interface of sp flash tool.
Make sure it says "download only" from the drop box. Click download then connect the phone to your computer. Flashing will start and should take about 1 minute and 30 seconds to finish.
If flashing doesn't start. Make sure you have vcom drivers installed. (Also for flashing to start, phone must be turned off obviously, but since you have semi brick, you don't have to worry about that).
Click to expand...
Click to collapse
My phone opened, but computer cannot see storage.i think phone's usb ports damaged. i can flash rom with sp flash tool only.
fastboot and recovery not working. i cant make root too. what can i do i dont know. recovery cant open, writing "no command".
faysoft said:
My phone opened, but computer cannot see storage.i think phone's usb ports damaged. i can flash rom with sp flash tool only.
fastboot and recovery not working. i cant make root too. what can i do i dont know. recovery cant open, writing "no command".
Click to expand...
Click to collapse
Go to developer mode menu (if you don't have it, tap on "build number" in "about phone" from settings, seven times and it will be activated). Then change how your USB acts when connected with computer.
If you can't, just use ES File explorer to send files between your computer and phone in FTP or SMB mode over WiFi.
Have the same problam.
The pc recognize the vcom device but only for 2-3 secconds and then disaper, then i get an error with sp flashtool.
Phone isnt tured on. At all.
I also have the same problem.
Is anyone has success with unbricking Power II in such case?
pacmancoder said:
I also have the same problem.
Is anyone has success with unbricking Power II in such case?
Click to expand...
Click to collapse
I do not know if it is late. I had the same problem with another phone. I was solved as follows:
1. Unplug the usb cable from the computer
2. Power off the phone
3. Press download on sp flash tool
4. Holding vol+ and power, plug the usb cable on the computer.
Hi,
can anyone provide me with nvram /nvdata backup please of Ulephone power 2?
I have probably correct IMEI, valid MAC fo Wifi/BT ...
It looks like my serial number changed to 123456789ABCDEF and I have no idea how to change it to original because MAUI (?) stucked on get kernel
I can find original box with correct serial and IMEis on stick
The only one problem with mobile is I am not able connect to mobile network - registration SIM to mobile network always fail.
and at MTK engineer I have only Bluetooth, FM Receiver, Wifi, Wifi CTIA, Wifi Display
I have nothing like Radio, CDS etc ...
OEM unlocked, TWRP, rooted
Some information probably lost when flashing
And of course another problem :
except GPS and proximity, all sensors does not work - G sensor, acceleration, magnetic sensor, compass . Probably configuration data is located at nvdata
i tried flash 5MB file nvdata.bin from different MTK 675x device, but nothings change
I tried flash 33 MB nvdata.img from same MTK 675x device, but I lost IMEI and nothing solved
This is why I need 33 MB NVDATA.IMG from another functional Ulephone power 2
I can change IMEI at MTK then ...
I had to flash , because phone was unusable - it stucked mostly on obtaining IP address wifi
after a while, phone disconnected from wifi and cant find any wifi or if find, then cant connect because of some security issue , after restart all was OK ...
Thanks