Related
Hi i just purchased from Amazon Samsung Fast Charge Wireless Charging Stand EP-NG930TBUGUS
And in fast charge mode it fully charges phone about in 3 hours about 5% in 10 minutes!
Is it correct?
Have you activated fast charge in the settings of tour phone? It's under Battery
Xophile said:
Have you activated fast charge in the settings of tour phone? It's under Battery
Click to expand...
Click to collapse
Yes its activated.
It is not normal this time?
SUNUN said:
Yes its activated.
It is not normal this time?
Click to expand...
Click to collapse
did you use it with orig s7 wall charger + orig cable? My result is 135 mins from 0% to full. If you have too thick case that will ruin the charging.
almaalma74 said:
did you use it with orig s7 wall charger + orig cable? My result is 135 mins from 0% to full. If you have too thick case that will ruin the charging.
Click to expand...
Click to collapse
yes all is original. without case the same result.
about 145 minutes in fast wireless charge on mine from 2% to 100%; but i have 4000Mah S7 Active not 3000mah s7 or 3500mah s7 edge. also tpu case but does not affect charge time
5% in 10 minutes at which battery level?
Did you have the display on our use the phone while charging?
maik005 said:
5% in 10 minutes at which battery level?
Did you have the display on our use the phone while charging?
Click to expand...
Click to collapse
battery monitor shows that every 10 minutes my phone charges 5%, no display is off only AOD is on didn't using the phone.
Did you position the phone till it show "fast charging wirelessly"?
vyis said:
Did you position the phone till it show "fast charging wirelessly"?
Click to expand...
Click to collapse
Yes sure
It is not Fast charging wirelessly.
mAh should be at least 1500 up to about 80 or 90 percent
maik005 said:
It is not Fast charging wirelessly.
mAh should be at least 1500 up to about 80 or 90 percent
Click to expand...
Click to collapse
and how to fix it?
Does ist say fast wireless charging or only wireless charging when you look on the lockscreen?
maik005 said:
Does ist say fast wireless charging or only wireless charging when you look on the lockscreen?
Click to expand...
Click to collapse
yes yes
Did you try to Plug in the usb cabel direct into the phone?
How fast does it charge then and does it say fast charging then?
maik005 said:
Did you try to Plug in the usb cabel direct into the phone?
How fast does it charge then and does it say fast charging then?
Click to expand...
Click to collapse
Yes and it charges device very fast.
Even with cabel directly plugged in it DOES NOT do FAST Charging. It should be over 2200 mA
---------- Post added at 09:11 ---------- Previous post was at 09:10 ----------
But only if the screen is off. With screen on it does charge only at 1000mA max
I am having the exact same problem. will be going down to Samsung service store tmr.
fast wireless charging takes 3-4 hours to full charge.
direct micro USB fast charging takes around 1.5 hours.
Yes, it did show FAST wireless charging.
xheavenic said:
I am having the exact same problem. will be going down to Samsung service store tmr.
fast wireless charging takes 3-4 hours to full charge.
direct micro USB fast charging takes around 1.5 hours.
Yes, it did show FAST wireless charging.
Click to expand...
Click to collapse
pls inform us when you will fix issue.
Cable fast charging is ok for me too. Only wireless is problem.
Hey,
Any ideas why phone charging can get slower ?
Using original 5V 2A charger, phone updated to Android 6.0.
It is charging around 5% per 10 mintes, but should be charging by 50% in 30 minutes.
Also I can not find setting for fast charging ... maybe it is gone after phone update ?
Thanks,
Janis
Same here...???*
Da_SilentKnight said:
Same here...???*
Click to expand...
Click to collapse
The speed should be around 1% per minute.
Max amperage delivered should be around 1.8A to 1.82A. This behaviour is for B330 and above.
zinko_pt said:
The speed should be around 1% per minute.
Max amperage delivered should be around 1.8A to 1.82A. This behaviour is for B330 and above.
Click to expand...
Click to collapse
Any official source about that? I was thinking it's same with Lollipop but I guess I was wrong. Cuz I did not realized any speed issue.
memht said:
Any official source about that? I was thinking it's same with Lollipop but I guess I was wrong. Cuz I did not realized any speed issue.
Click to expand...
Click to collapse
I believe it's common knowledge. My experience too.
kipeens said:
Hey,
Any ideas why phone charging can get slower ?
Using original 5V 2A charger, phone updated to Android 6.0.
It is charging around 5% per 10 mintes, but should be charging by 50% in 30 minutes.
Also I can not find setting for fast charging ... maybe it is gone after phone update ?
Thanks,
Janis
Click to expand...
Click to collapse
The fast charging option is gone after the update, yes.
The fone charging slowly can happen due to many reasons, charger defect, device defect, custom rom installed, any app conflicting. Did you have any of that?
I got a new Qualcomm quick charge 3 certified charger ..but according to the readings in ampere app ....the output is like 1750 mA ..but the same charger with note 9 gives an output of 2900-3000 mA ...is this the phone problem ...if anyone has the same problem ....and found a solution ..please help
It does not charge at full power all the time. There are several charging states and the full power one is from 15% to 65%, I think.
2155X said:
It does not charge at full power all the time. There are several charging states and the full power one is from 15% to 65%, I think.
Click to expand...
Click to collapse
Yeahh ....I checked that also ...I measured the mA from mi charger ..it was 2800-2900 mA ..the new charger gives about 1650-1750 mA...at 40% charge
The kernel limits max current to 2800ma, but you can increase it with a custom kernel. It could be that your new charger is not properly supported.
2155X said:
The kernel limits max current to 2800ma, but you can increase it with a custom kernel. It could be that your new charger is not properly supported.
Click to expand...
Click to collapse
Yeah probably
venkatkrishna_s said:
Yeahh ....I checked that also ...I measured the mA from mi charger ..it was 2800-2900 mA ..the new charger gives about 1650-1750 mA...at 40% charge
Click to expand...
Click to collapse
What is temperature of the phone? Check this post and see if keeping your phone around 25 Celsius increase charging speed.
katoda_ltd said:
What is temperature of the phone? Check this post and see if keeping your phone around 25 Celsius increase charging speed.
Click to expand...
Click to collapse
I posted that.... After doing that ..I posted it .. Anyways thanks for coming back and addressing it
Geez, stupid me. Must pay more attention to a post's author, this situation is simply hilarious
katoda_ltd said:
What is temperature of the phone? Check this post and see if keeping your phone around 25 Celsius increase charging speed.
Click to expand...
Click to collapse
Temperature is just a part of the variables. Other variable to consider which was not stated was voltage.
QC 3.0 spec shows that it can charge at a voltage between 3.2V to 20V by doing +/- 200mV increment/decrement. Looking at the current alone is incomplete.
3DRIAN said:
Temperature is just a part of the variables. Other variable to consider which was not stated was voltage.
QC 3.0 spec shows that it can charge at a voltage between 3.2V to 20V by doing +/- 200mV increment/decrement. Looking at the current alone is incomplete.
Click to expand...
Click to collapse
Can anyone tell me quickcharge 4.0 charger?
To power up, you consume Red Bull. But your phone just needs its adaptive fast charger. Rate this thread to express how quickly the Realme X2 Pro can charge. A higher rating indicates that it charges extremely fast.
Then, drop a comment if you have anything to add!
Quick isn't the word. It's amazing seeing how fast it charges.
Can it be charged with a 5 volt charger?
I think I have a problem with fast charging.
Yesterday while the phone was charging, electricity in my house was shutted down. When it came back, I can see than now, I charge 1 % on 35 seconds, instead of 20 sec before.
Could it have the battery damaged ? I doubt so, buty it's strange.
I tried when battery was 82%
Maybe it's quicker when battery is low ?
What's your thoughts about this situation ?
Thanks !
Edit : Okay, after 85% it slows down, but before it's okay
ManuBBXX said:
I think I have a problem with fast charging.
Yesterday while the phone was charging, electricity in my house was shutted down. When it came back, I can see than now, I charge 1 % on 35 seconds, instead of 20 sec before.
Could it have the battery damaged ? I doubt so, buty it's strange.
I tried when battery was 82%
Maybe it's quicker when battery is low ?
What's your thoughts about this situation ?
Thanks !
Edit : Okay, after 85% it slows down, but before it's okay
Click to expand...
Click to collapse
Yeah it slows down towards the end I'll go from 0-99 in 28-30 min then takes some time sometimes to get the last 1%. Battery life is also incredibly good.
chipcamel said:
Yeah it slows down towards the end I'll go from 0-99 in 28-30 min then takes some time sometimes to get the last 1%. Battery life is also incredibly good.
Click to expand...
Click to collapse
Wrong screenshot
chipcamel said:
Wrong screenshot
Click to expand...
Click to collapse
Yeah battery life is outstanding..
Anyway, I have a little weird thing :
This battery monitor stats shows me different SOT than GSAMBatteryMonitor.
GSAM shows 2 hours more (wich I think wrong), and this delay grows while battery dercreases.
Do you have this app showing the same stats than colorOS battery monitor ?
ManuBBXX said:
Yeah battery life is outstanding..
Anyway, I have a little weird thing :
This battery monitor stats shows me different SOT than GSAMBatteryMonitor.
GSAM shows 2 hours more (wich I think wrong), and this delay grows while battery dercreases.
Do you have this app showing the same stats than colorOS battery monitor ?
Click to expand...
Click to collapse
I just downloaded the app you're talking about give me a day or so I'll give you an update
50W Charge is impressive can't wait to get in hands.
Can you disable fast charge (like in samsung galaxy note 9)?
What time does it take to reach 100 from 0?
ManojKing said:
What time does it take to reach 100 from 0?
Click to expand...
Click to collapse
Usually 28 minutes and a maximum of 35
labib2002 said:
Usually 28 minutes and a maximum of 35
Click to expand...
Click to collapse
Yes it's really fast
Greetings.
I got my X2 Pro about 2 days ago. Charging speed is even better than advertised, as it takes less than 30 minutes to reach full charge. But phone usually gets too hot when fast charging. Do I experience this problem alone or do you guys too? Kinda worried about battery health in the long run if it gets too hot everytime I charge it.
Thanks before
reyhanjuala said:
Greetings.
I got my X2 Pro about 2 days ago. Charging speed is even better than advertised, as it takes less than 30 minutes to reach full charge. But phone usually gets too hot when fast charging. Do I experience this problem alone or do you guys too? Kinda worried about battery health in the long run if it gets too hot everytime I charge it.
Thanks before
Click to expand...
Click to collapse
Same thing here, so I don't charge more than 40 - 45% at a time.
If my battery is below 50%, I charge in 2 times with a 10 min pause.
Doing sop, you don't reach hoptter than 33 degrees instead of 38+
I can't seem to get a decent standard charging from 5V 2A chargers or Powerbanks, even a QC3 Powerbank only delivers 0,9-1A.
I only get about 900mA according to the Ampere-App. {On the contrary, I even get 1,8A from the original wall plug at 80% SoC).
Do you also struggle?
devilgenius said:
Can you disable fast charge (like in samsung galaxy note 9)?
Click to expand...
Click to collapse
I tried to use a 5 watt charger, and it works. Been searching in settings for an option to disable fast charging, but I can't find one.
---------- Post added at 09:07 AM ---------- Previous post was at 09:04 AM ----------
Polarfuchs said:
I can't seem to get a decent standard charging from 5V 2A chargers or Powerbanks, even a QC3 Powerbank only delivers 0,9-1A.
I only get about 900mA according to the Ampere-App. {On the contrary, I even get 1,8A from the original wall plug at 80% SoC).
Do you also struggle?
Click to expand...
Click to collapse
Same here. I used a 9V 2A charger, and it won't go more than 1100mA.
I wonder if this is a detection error from the apps. I think they don't consider the dual battery layout and only display half of the true value.
The error that the app "charger tester" shows let's me think this or does support my theory.
All apps seem to not be able to show the correct current flow because of the dual-batteries.
I found the engingeering mode and can confirm that the phone charges with 5V 2A on dumb chargers.
And also supports QC 18W with 9V 2A
As well as the Oneplus 20W Dash charger with 5V 4A.
Polarfuchs said:
I can't seem to get a decent standard charging from 5V 2A chargers or Powerbanks, even a QC3 Powerbank only delivers 0,9-1A.
I only get about 900mA according to the Ampere-App. {On the contrary, I even get 1,8A from the original wall plug at 80% SoC).
Do you also struggle?
Click to expand...
Click to collapse
physixthegreat said:
I tried to use a 5 watt charger, and it works. Been searching in settings for an option to disable fast charging, but I can't find one.
---------- Post added at 09:07 AM ---------- Previous post was at 09:04 AM ----------
Same here. I used a 9V 2A charger, and it won't go more than 1100mA.
Click to expand...
Click to collapse
Super VOOC (and also VOOC) have their own protocol of charging mechanism. It's not the same with other quick charge method like Quick Charge 3.0.
You will not have VOOC charging if you are not using right adapter and right cable. You try use Super VOOC charge with other USB cable, VOOC charging will not work.
So when you using other adapter or cable, you'll got standard 5V charging max 2A.
The stock charger says it gives output of 18 watt . But in my case maximum ouput goes to 1.5-2 amp/3.5-4volts which is very less . It would be helpfull if anyone tells how to get 9volts or 12 volts.
Kriss21999 said:
The stock charger says it gives output of 18 watt . But in my case maximum ouput goes to 1.5-2 amp/3.5-4volts which is very less . It would be helpfull if anyone tells how to get 9volts or 12 volts.
Click to expand...
Click to collapse
Are you on stock rom or custom rom?
Stock
MIUI 11.0.9
If you are ok with rooting your device. I can tell you how to do so.
1. Root your device.
2. Install Advance charging control app(AccA) .
Link- https://f-droid.org/packages/mattecarra.accapp/
3. Give root permission.
Done.
(Don't install the magisk module app will work fine without it. The magisk module is installed and forget kind of module which you cannot modify to your own need)
Now you can set the speed you want (if your device suppots the spped you typed in it).
Its not just that, you can limit the charging % after which the charger automatically disconnects. I find it very helpful when i charge my device overnight. Automatically disconnects after 95%.
It also looks at your thermal of your battery. You can set your own temp % after which it starts cooling down by limiting the current/volt to the battery.
I personally suggest this app.
Thanks to @VR25.
Hope it works for you.
Thanks . Will try it.
Kriss21999 said:
Thanks . Will try it.
Click to expand...
Click to collapse
So, what was the maximum voltage you could set using Advance charging control app?
i.e what is the max voltage limit of poco f1
Also do you have any other charger than the stock one?
Charging cable issue?
Mine had issue with the charging cable.. tried with other charging cable it worked properly.. original charging xable got damaged witin 4 months of use..
besap18 said:
Are you on stock rom or custom rom?
Click to expand...
Click to collapse
Change cable, then change charger. Usually its either of those two. If it works, good. If not then it might be an issue with the software try to reflash (backup first). Worst case scenario it's the port
The issue is solved for me (Stock Rom ) . Bought new cable upto 3amp . Charged 87% in one hour (screen off) .
Tip : Keep the temperature below 35 degrees .
Xe1503 said:
So, what was the maximum voltage you could set using Advance charging control app?
i.e what is the max voltage limit of poco f1
Also do you have any other charger than the stock one?
Click to expand...
Click to collapse
I dint tried advance charging control ,Changing cable worked for me . And i have stock 18 watt charger , Maximum voltage goes upto 4.856.
Kriss21999 said:
I dint tried advance charging control ,Changing cable worked for me . And i have stock 18 watt charger , Maximum voltage goes upto 4.856.
Click to expand...
Click to collapse
How do you know the voltage is 4.856? Do you have usb meter?
Xe1503 said:
So, what was the maximum voltage you could set using Advance charging control app?
i.e what is the max voltage limit of poco f1
Also do you have any other charger than the stock one?
Click to expand...
Click to collapse
Don't know about other charges but i use stock charger and mine charges fully within 45-55 mins(0-100).
Stock charger brick is only fast charger 3 whereas our poco supports fast charge 4.
You can try ambrane or razer fast charger 4 brick for charging your device faster than stock charger
Xe1503 said:
How do you know the voltage is 4.856? Do you have usb meter?
Click to expand...
Click to collapse
Use Advance Charging control App. It gives you volts as well mAh speed by which your phone is charging or discharging.
Xe1503 said:
How do you know the voltage is 4.856? Do you have usb meter?
Click to expand...
Click to collapse
There are many applications on playstore to check.
Ex:- AMPERE , ACCUBATTERY
Kriss21999 said:
There are many applications on playstore to check.
Ex:- AMPERE , ACCUBATTERY
Click to expand...
Click to collapse
As I suspected, you're aren't aware what the ampere app is for.
Here take this for starters:
https://youtu.be/PvgLEii7f0w
The ampere app is for........amperes, it does not show charging voltage. It's the battery's voltage. Same is the case for accubattery.
I use Franco kernel manager app from playstore and it shows watts, which is at least somewhat believable.
I don't know about ACCA because it doesn't work without root and works on very specific phones.
Try with Franco kernel manager app(root not required) and check the watt.
---------- Post added at 07:45 PM ---------- Previous post was at 07:28 PM ----------
besap18 said:
Don't know about other charges but i use stock charger and mine charges fully within 45-55 mins(0-100).
Stock charger brick is only fast charger 3 whereas our poco supports fast charge 4.
You can try ambrane or razer fast charger 4 brick for charging your device faster than stock charger
Use Advance Charging control App. It gives you volts as well mAh speed by which your phone is charging or discharging.
Click to expand...
Click to collapse
You mean *1 hour* 45-55 mins(0-100)?
POCO F1 has 4000 mah, or 4.0 A * 3.7 v = 14.8 Wh, so if you charge your phone at 14.8 W for 1 hour then it will go 0-100%
or it will take 1 hour to charge your phone from 0% to 100% if you charge at a constant 14.8 watt. Which never happens, because hardware thermal throttling and software thermal throttling, after 30-50% the watts will go down, in the last 80-90% it will really be low. Even if you remove all thermal throttling and charge your phone in ice cubes, still because it's a 18 WATT QC 3 charger, it cannot charge in 45-55 mins.
What you're saying is most certainly impossible. Either that or your numbers aren't accurate, like it wasn't from 0-100% maybe 25-90% or it wasn't 45-55 min , maybe an hour and a half or you don't use the stock 18 watt qc 3 charger, or your battery is defective or you don't have a poco f1..
Xe1503 said:
How do you know the voltage is 4.856? Do you have usb meter?
Click to expand...
Click to collapse
Xe1503 said:
As I suspected, you're aren't aware what the ampere app is for.
Here take this for starters:
https://youtu.be/PvgLEii7f0w
The ampere app is for........amperes, it does not show charging voltage. It's the battery's voltage. Same is the case for accubattery.
I use Franco kernel manager app from playstore and it shows watts, which is at least somewhat believable.
I don't know about ACCA because it doesn't work without root and works on very specific phones.
Try with Franco kernel manager app(root not required) and check the watt.
---------- Post added at 07:45 PM ---------- Previous post was at 07:28 PM ----------
You mean *1 hour* 45-55 mins(0-100)?
POCO F1 has 4000 mah, or 4.0 A * 3.7 v = 14.8 Wh, so if you charge your phone at 14.8 W for 1 hour then it will go 0-100%
or it will take 1 hour to charge your phone from 0% to 100% if you charge at a constant 14.8 watt. Which never happens, because hardware thermal throttling and software thermal throttling, after 30-50% the watts will go down, in the last 80-90% it will really be low. Even if you remove all thermal throttling and charge your phone in ice cubes, still because it's a 18 WATT QC 3 charger, it cannot charge in 45-55 mins.
What you're saying is most certainly impossible. Either that or your numbers aren't accurate, like it wasn't from 0-100% maybe 25-90% or it wasn't 45-55 min , maybe an hour and a half or you don't use the stock 18 watt qc 3 charger, or your battery is defective or you don't have a poco f1..
Click to expand...
Click to collapse
Thanks for explaining , understood now.