If I am in a call on SIM1 and somebody else is calling me on SIM1 I can see the 2nd call and the caller also gets a notification if he is on the same network or some busy signal after some time if not.
However if I am in a call on SIM1 and somebody else is calling me on SIM2 there is no info on my side and the caller gets a message that I am not in the network or the phone is turned off. That is normally expected for dual-SIM dual-standby but all such dual-SIM phones that I have seen can (as long as you let them know the numbers of the 2 SIMs and you activate a specific option) do a small trick - right before you get into the 1st call (SIM1 above) the phone sets call forwarding from SIM2 to SIM1 and that way you get a call waiting when somebody else calls on SIM2 and he gets a busy signal or similar. At the end of the call any call forwarding added by the phone is of course removed.
The question is of course this - does Poco F1 has such an option and how do I activate it?!
More info
More info:
http://archive.is/nWEJQ
Related
After using QPST for my Dad's Inc4g it has 2 odd cellular problems.
#1
It can make outgoing calls for a few minutes.
But then it says that the “phone number is not active or invalid” (like it’s not activated).
Then the only call it can make is to 611 (data and wifi off), but it gives me his correct balance and minutes used (so it's still connected to his account).
Rebooting does not allow it to make outgoing calls either.
It's as if it's partially dropped off the verizon network somehow because turning the radio on and off again also doesn't work (airplane mode on/off).
And when another phone calls him it goes straight to his voicemail.
BUT….if another verizon phone calls he CAN receive that incoming call no problem.
*Then once he answers that incoming call, he can magically make an outgoing call again!
So can anyone tell me what I might need to change, to stop it from loosing the ability to make outgoing calls?
It’s brand new (NOT rooted or anything else).
The Preferred network is set to CDMA only.
Only changes have been through QPST, and switched to NV-Only mode so he doesn't have to use the sim card.
Also after QPST the roaming triangle popped up, but I have the 58012 PRL (isn’t this the latest for this phone)?
#2
If he starts to dial a number, but then immediately hangs up (accidental dial), his next call gets the "system busy" network error.
Then attempting to make a call after that gives the same error as above (requiring a verizon phone to call to get him back on the network).
Could someone try do this and see if they can repeat this error?
So to anyone who has used QPST with this phone, or flashed it to another carrier, do you have any change suggestions for either of these problems? Maybe changing something in EPST?
Thanks for your help.
Hi I apologise in advance if I am posting in the wrong place or I'm just being a numpty.
I suspect it's me being dumb that's the problem but when someone rings one of my 2 SIMs in my Xiaomi Note5Plus with Global ROM from Xiaomi not flashed, I cannot see from the screen which SIM the incoming call is on. OK, I have 2 different ring tones set-up and that is fine but on silent/no vibration or if I miss the call, it's a real nuisance not knowing which SIM received the call. As an example, if I make a call to each of the SIMs from another mobile, then my phone just shows that I have had 2 calls from that mobile, rather than one call on each SIM from that mobile.
My old THL2015 did this automatically and so I could always tell what was going on.
The reason that this is particularly important for me is that SIM1 is for use by everyone who calls me and SIM2 is my back up line. If someone calls me, I need to know (if they are not in my contact list) whether this is a "real" call or a junk call on SIM2.
Hope all that makes sense and one of you kind people can suggest a Settings solution or an app please.
My thanks for any help offered.
Hello guys,
I am facing a real big issue after updating to the stable android pie release on my poco f1
I am using a jio sim. The incoming calls are not shown on the phone. Whenever a call comes to my number it never shows on the phone the caller will hear the dialer tone as normal
Also when I try to make a call it shows a message mobile network unavailable, mobile data and sms works fine all this time.
When I reboot the phone none of the issues are there for 15 to 20 minutes then it comes back.
There were no issues when i put the sim in the second sim slot but I need to have the same card.
I am really frustrated about this issue, I have missed many important calls as it never showed up on the phone
I cannot find any one else facing this issue. What could be the reason for this ? I hope it's some kind of software bug that can be fixed.
Please help me to fix this guys
Thank you
Hi!
Just switched to a Xiaomi MI 10T Pro after many years of Samsung.
Have a problem I cant find a solution to.
My sim2 receives calls with no problem.
But if someone tries to call my sim1, its being forwarded to my sim2 (the callers phone also shows that the call is forwarded).
I have checked all the settings, none of the cards have call forwarding enabled.
I would really appreciate any suggestions.
Thank you!
Hello! As per thread title I was wondering if it is possible to receive a call on both sims at same time. To be more precise even while in a call on sim1, I would like to receive or at least being notified of calls received by sim2.
I tried some settings but nothing. Does it depend purely on the sims carrier or is it something at phone setting?
Thanks,