Can't charge my battery without rebooting - Xiaomi Poco F1 Questions & Answers

Hi there, i have no idea what is going on with the cellphone, since i used it for the first time i tried to charge the battery without any success, i reboot it while the usb-c was connected and it did charged, so now every time i want to charge it i have to connect it and reboot it. Also if i disconnect it after rebooting and connect it again it wont charge until i reboot it again, seems like it doesn't recognized the usb unless i reboot it. Could someone help me? Thanks
Have:
- Android 9 PKQ1.180729.001
- MIUI Global 10.2 Estable 10.2.2.0 (PEJMIXM)
- Model M1805E10A

drchau said:
Hi there, i have no idea what is going on with the cellphone, since i used it for the first time i tried to charge the battery without any success, i reboot it while the usb-c was connected and it did charged, so now every time i want to charge it i have to connect it and reboot it. Also if i disconnect it after rebooting and connect it again it wont charge until i reboot it again, seems like it doesn't recognized the usb unless i reboot it. Could someone help me? Thanks
Have:
- Android 9 PKQ1.180729.001
- MIUI Global 10.2 Estable 10.2.2.0 (PEJMIXM)
- Model M1805E10A
Click to expand...
Click to collapse
Install a custom Rom or MIUI10 latest beta build. If problem persists then problem is hardware related.

Been facing the same issue, @drchau did you find a fix for it ?

It is a hardware problem.. seems like it is somewhat common. I had the same issue last week. Tried several stock and custom os. Then realised it should be a hardware issue. Mine had same behaviour ( reboot to charge ) and then problem with otg not detecting. And usb c cable is recognised in only one way.
So booked a slot for service . Went to service today. Found three customers with same issues , and then the service center replaced my usb sub board and others too. Took one hour total. And everything is fine now.
Total cost is INR 700 for board + INR 350 for service + 19% GST. = 1250 INR.
They won't replace the port. It's a whole sub board . They replace it. You will get it for free if under warranty.

I have this problem with my Mi Max 3. I have to reboot OR for some reason it will charge via an OTG dock without rebooting (odd ... If I plug the same usb c cable in directly it doesn't recognize it.
A couple of times when I unrooted and reverted to stock unrooted, the charging issue went away.
I realize that many here are convinced this is a hardware issue but I also routinely disable/delete a lot of crapware and system apps via ADB .... Can't help thinking there might be a coded dependency issue.
I am in the USA so getting it serviced isn't an option ... I have 3 Xiaomi phones and would love to add a Poco F3 when I can afford to, but these charging issues are being reported with great frequency and I am hopeless at soldering.
If anyone knows of a repair shop in the USA they trust with their Xiaomi products I'd be grateful to know the name.
Thanks!

showlyshah said:
It is a hardware problem.. seems like it is somewhat common. I had the same issue last week. Tried several stock and custom os. Then realised it should be a hardware issue. Mine had same behaviour ( reboot to charge ) and then problem with otg not detecting. And usb c cable is recognised in only one way.
So booked a slot for service . Went to service today. Found three customers with same issues , and then the service center replaced my usb sub board and others too. Took one hour total. And everything is fine now.
Total cost is INR 700 for board + INR 350 for service + 19% GST. = 1250 INR.
They won't replace the port. It's a whole sub board . They replace it. You will get it for free if under warranty.
Click to expand...
Click to collapse
There's probably a couple mosfets and what not on that PCB. Maybe bad design or a manufacturing defect caused a solder crack or trace failure. Maybe a component.
These boards are usually inexpensive.
A relatively easy fix if so.

brasscupcakes said:
I have this problem with my Mi Max 3. I have to reboot OR for some reason it will charge via an OTG dock without rebooting (odd ... If I plug the same usb c cable in directly it doesn't recognize it.
A couple of times when I unrooted and reverted to stock unrooted, the charging issue went away.
I realize that many here are convinced this is a hardware issue but I also routinely disable/delete a lot of crapware and system apps via ADB .... Can't help thinking there might be a coded dependency issue.
I am in the USA so getting it serviced isn't an option ... I have 3 Xiaomi phones and would love to add a Poco F3 when I can afford to, but these charging issues are being reported with great frequency and I am hopeless at soldering.
If anyone knows of a repair shop in the USA they trust with their Xiaomi products I'd be grateful to know the name.
Thanks!
Click to expand...
Click to collapse
It could be (most likely is) a dependency especially if it happened right after the edits.
I prefer to package block rather than edit them out. Mistakes are easily corrected... most times.
Don't attempt soldering anything in these devices unless you know how to, not the place to learn.
Many though aren't soldered in, they're connected with ribbon cables more commonly. See a device tear down to find out.
A good phone repair shop should be able to handle it.

blackhawk said:
It could be (most likely is) a dependency especially if it happened right after the edits.
I prefer to package block rather than edit them out. Mistakes are easily corrected... most times.
Don't attempt soldering anything in these devices unless you know how to, not the place to learn.
Many though aren't soldered in, they're connected with ribbon cables more commonly. See a device tear down to find out.
A good phone repair shop should be able to handle it.
Click to expand...
Click to collapse
Thanks for your reply.
I'm pretty sure from video teardowns that the parts involved in the MM3 require soldering (there's some kind of board involved with replacing the port)
I still love the Mi Max 3 but it isn't worth a spendy repair because the carriers here are shutting down 3G and HSPA+ soon which only leaves me with FDD LTE 4 (not great where I live).
Repair shops aren't as expert in the states sadly ... most people here buy their devices from carriers.
I needed a camera replaced on my old Max but they didn't want to order parts so I ordered it and did the replacement myself (but only because I didn't have to solder).
If Asurion insurance from Amazon covers global phones I'll get my next Xiaomi insured. Too bad Xiaomi won't just let us ship at our own expense to their service centers in China or Europe.

brasscupcakes said:
Thanks for your reply.
I'm pretty sure from video teardowns that the parts involved in the MM3 require soldering (there's some kind of board involved with replacing the port)
I still love the Mi Max 3 but it isn't worth a spendy repair because the carriers here are shutting down 3G and HSPA+ soon which only leaves me with FDD LTE 4 (not great where I live).
Repair shops aren't as expert in the states sadly ... most people here buy their devices from carriers.
I needed a camera replaced on my old Max but they didn't want to order parts so I ordered it and did the replacement myself (but only because I didn't have to solder).
If Asurion insurance from Amazon covers global phones I'll get my next Xiaomi insured. Too bad Xiaomi won't just let us ship at our own expense to their service centers in China or Europe.
Click to expand...
Click to collapse
Many times you replace the whole port PCB. If it's soldered on it could be a pain even with the right tools/experience.
You could try a factory reset to undo the disabled apks to see if that was it.

Thanks, I've tried factory reset and it helps for a little while. For now its still usable ... Rebooting to charge isn't a big deal. I do find it odd though that I can still charge via OTG dock without rebooting.
The bigger issue is what to buy to replace it. I don't trust Miui not to be buggy anymore and I have grown to hate constantly having to disable optimizations that inhibit sms, email and even calls (if I try to use TMO towers... AT&T MVNOs seem unaffected ).
I wouldn't mind doing all those steps once but my permissions don't stick for very long.
The TCL 20 might be worth a look...or maybe Realme if I see one with a bigger screen... I'm wedded to large screen models, mid price at best, with NA LTE band support ...
TCL also has a couple of LTE tablets with decent specs coming out ... but LTE tablets for USA export almost always ship with the dialers disabled so you can't make calls.
I'm trying to out till the end of June. By that time, hopefully the Poco F3 bugs will be resolved. Retailers aren't even shipping it here yet.

brasscupcakes said:
Thanks, I've tried factory reset and it helps for a little while. For now its still usable ... Rebooting to charge isn't a big deal. I do find it odd though that I can still charge via OTG dock without rebooting.
The bigger issue is what to buy to replace it. I don't trust Miui not to be buggy anymore and I have grown to hate constantly having to disable optimizations that inhibit sms, email and even calls (if I try to use TMO towers... AT&T MVNOs seem unaffected ).
I wouldn't mind doing all those steps once but my permissions don't stick for very long.
The TCL 20 might be worth a look...or maybe Realme if I see one with a bigger screen... I'm wedded to large screen models, mid price at best, with NA LTE band support ...
TCL also has a couple of LTE tablets with decent specs coming out ... but LTE tablets for USA export almost always ship with the dialers disabled so you can't make calls.
I'm trying to out till the end of June. By that time, hopefully the Poco F3 bugs will be resolved. Retailers aren't even shipping it here yet.
Click to expand...
Click to collapse
After the factory reset you need to find the akp that triggers this. Reviewing the most recent running and/or cache processes can narrow down the list.
Use Package Blocker PD MDM to clear the data in suspect apks. Unlike clearing the data in settings PD MDM leaves no nulls behind. Those silly nulls can mean big trouble.
Since it keeps returning the offending apk may be amenable to being package blocked depending on its function/dependencies.
This is how you find it.
Android Setup is a prime suspect. I cured a similar C-port error message like this by deleting the null marks in its data which showed as zero.
Happy hunting

Related

Kinda sad

Well my X10 usb port is broken and won't charge, so I decided I might as well get a new phone (I looked up trying to fix it and etc but came up with nothing). I bought the phone unlocked and had it imported back when it first came out so no warranty for me. Well anyway the point of this is I decided I don't want to spend so much money right now so I'm gonna stick with phones provided by my service provider which is T-Mobile US, so at the moment I have the choice between the Samsung Vibrant & the myTouch 4G and I just wanted to hear some opinions on that (I don't really like physical keyboards so the G2 is out) I'm still going to do my own research but its always nice to hear other peoples thoughts.
you could just buy a portable charger for the battery...
RS Online has micro USB-ports, and if you fear that won't look any good it's a good opportunity to hack it into wireless charging:
http://www.rs-online.com/index.html
http://www.slashgear.com/htc-evo-4g-touchstone-hack-adds-wireless-charging-video-1389601/
Um a portable charger wouldn't be able to help me if I need to connect the phone to the computer to do things like flashing and etc
Have you tried another charger? Had the same problem and a new charger worked, phoned my provider they sent me a replacement and I just swapped the charger.
Sent from my Nexus S using XDA App
onei0077 said:
Have you tried another charger? Had the same problem and a new charger worked, phoned my provider they sent me a replacement and I just swapped the charger.
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
Yeah tried multiply different ones. At this point I know its a fact its the usb port because its jiggling.
So what's your plan with the broken device? RMA, selling as defective, or leaving in a drawer?
If the latter then try fixing it first - it's not the first phone with a loose micro-usb port.
A few links:
X10, sounds very much like your problem
http://forum.xda-developers.com/showthread.php?t=777721&page=3
Desire
http://forum.xda-developers.com/showthread.php?t=822771
A guide valid for mini (not micro!) usb
http://hackaday.com/2007/11/08/how-to-replace-a-mini-usb-port-on-your-cellphone/
If you are not comfortable to attempt a repair on your own (then don't try) there are others on this forum and elsewhere with the tools, knowhow and goodwill to help you.

HD2 Intermittant Issue...

Hi, I have a couple of HD2's ready for use within the business I work for.
These HD2's were purchased as replacements for older HD2's that had been used and were getting tempramental and old.
I have recieved the new HD2's and heres my problem:
The touch screen seems to decide when, and IF it works. The first time I EVER got it out of the box, unwrapped it etc the touch didn't work.
After a couple of restarts the touch works, then after a bit it will then decide not to work.
This happens constantly, it will work, then wont work, then work, then wont work.
When it works it is fine, just like the HD2 should be, it just seems to be like a moody teenager who decides when and if it want's to work.
Any one know what could cause this? Why it is happening and why it works and then doesn't?
Thanks !
the touch has always been a weak point of this phone, and your issue doesn't sound all that uncommon.
if they still have older version, rom then you should certainly update that.
if there's any warranty you should definitely go that route immediately,, because you almost certainly aren't gonna fix it.
Hi mate
Yes I have updated the ROM's which went from 1.4 (ish) to the current ROM listed on the HTC website. That seemed to fix it, but then I realised the phone was in a good mood, and 10 minutes later it started its hissy fit again.
And about warranty I don't know as I didn't buy them, we may have to attempt to send them back but thats gonna take weeks, as it took weeks for them to arrive. And we need them out and about tbh.
Do you have any idea what the cause is?
Hardware/Software?
Thanks !
sorry no clue why, and I'd say it's most likely hardware,,, a failing digitizer by the sound.
Sounds like the common digitizer issue, just had same with my personal TMOUS HD2.
Our local supplier said he had units 100% new but old that had failed in the box, reckons digi ribbon bonding to digi is bad on both solder & socket types.
From 20+ HD2 handsets we have running in our company I would conclude similar myself.
My personal handset has had extremely light & sympathetic use & hardly minimal use of end key but it still failed.
Hardware durability of digi/micro USB port & mainboard thermal control/BGA solder quality is very poor to be polite ...

[Q] Charging Flex Cable Problem

Hi, I have the Galaxy Note i717 and had to replace my charging port as it had stopped charging reliably. I bought one of the many on ebay for around 8 bucks. I proceeded to put it in when I received it but to my dismay I no longer could get service at all, just wifi. So just to verify it was nothing I broke I put the old pcb back in and service returned. At that time I believed it was just a defective unit, so second try at it same thing no service old one works fine. Is this a problem anyone has ran into before? Any help I would appreciate.
jpeeler said:
Hi, I have the Galaxy Note i717 and had to replace my charging port as it had stopped charging reliably. I bought one of the many on ebay for around 8 bucks. I proceeded to put it in when I received it but to my dismay I no longer could get service at all, just wifi. So just to verify it was nothing I broke I put the old pcb back in and service returned. At that time I believed it was just a defective unit, so second try at it same thing no service old one works fine. Is this a problem anyone has ran into before? Any help I would appreciate.
Click to expand...
Click to collapse
It is quite possible that either your new port is the wrong part, or is damaged.
The port wiring is different between models ...I.E. SGH-I717, N7000, and other note models.
Even the charge cables are different part numbers between models, but visually look identical.
It just sounds like the port wiring is different to me ..
I suggest getting the port directly from samsung...even though it will cost a bit more.
At least then you have a fall back if the port won't function.
Or perhaps have the port repaired by Samsung directly ....
I'm sorry I can't offer more help .g
gregsarg said:
It is quite possible that either your new port is the wrong part, or is damaged.
The port wiring is different between models ...I.E. SGH-I717, N7000, and other note models.
Even the charge cables are different part numbers between models, but visually look identical.
It just sounds like the port wiring is different to me ..
I suggest getting the port directly from samsung...even though it will cost a bit more.
At least then you have a fall back if the port won't function.
Or perhaps have the port repaired by Samsung directly ....
I'm sorry I can't offer more help .g
Click to expand...
Click to collapse
Well both pcb boards that they sent me have the same markings as the one I removed. They also say on them SGH_I717_SUB_REV1.0_1107
So I do believe it to be the correct part. Just to clarify the new boards do charge the phone just cellular service stops. Maybe by some crazy luck I got two faulty boards. I wasn't sure they were going to send me a replacement so I ordered from another company as well so I guess I will have to see if that one works,
Interesting ....
The part seems okay ...
And the odds of two bad ports in a row is remote at best ....
Some time ago I saw a thread about an extra wire that traveled down from the antenna to the charging port....
And users were reporting that this very small wire was being damaged or missed when the port was serviced.
I've never seen this wire or connection ......but I figured I'd bring it up ..
Try a general search on the topic ...and see if it yields a result.....
I just remember it being a big deal ....g
Just wanted to update the post in case this happens to anyone else. After getting the free replacement for the first part I believed to be defective I also ordered from another company as it took more than a month for my replacement, so I believed them to had stood me up. Well the one from the other company arrived today, and worked. Maybe the others were for different networks or something. I don't know if that is possible Rogers vs ATT frequencies and what not but it worked and all is well.
jpeeler said:
Just wanted to update the post in case this happens to anyone else. After getting the free replacement for the first part I believed to be defective I also ordered from another company as it took more than a month for my replacement, so I believed them to had stood me up. Well the one from the other company arrived today, and worked. Maybe the others were for different networks or something. I don't know if that is possible Rogers vs ATT frequencies and what not but it worked and all is well.
Click to expand...
Click to collapse
I am having issues as well...
My phone has a Rev1.0_1107 part, and I cannot charge unless I play with the cable, so i decided to replace this port.
1st was from China (ebay) and received no signal, only wifi. Rev1.0_1107
2nd was a replacement from the same company, same issue. Rev1.0_1107
3rd was from a place in CA (ebay) and is Rev2.0_1206 and same issues.
I can put my original part in there, and I get signal just fine... anybody have any ideas on this matter? It's frustrating to have to keep battery swapping and would like to get this fixed.
MisterLas said:
I am having issues as well...
My phone has a Rev1.0_1107 part, and I cannot charge unless I play with the cable, so i decided to replace this port.
1st was from China (ebay) and received no signal, only wifi. Rev1.0_1107
2nd was a replacement from the same company, same issue. Rev1.0_1107
3rd was from a place in CA (ebay) and is Rev2.0_1206 and same issues.
I can put my original part in there, and I get signal just fine... anybody have any ideas on this matter? It's frustrating to have to keep battery swapping and would like to get this fixed.
Click to expand...
Click to collapse
The one that finally worked for me was from ebay company (no.1-tech) also china but has been operating flawlessly for sometime now.
jpeeler said:
The one that finally worked for me was from ebay company (no.1-tech) also china but has been operating flawlessly for sometime now.
Click to expand...
Click to collapse
Noted... thanks. I have searched them out and they only appear to have the cable for the N7000. Can anyone else recommend a place to buy these from?
Just noticed that when it's near my window, I get 1 bar of service... So it's like my signal strength is uber weak. I have a microcell in my home, and it is functioning properly (other ATT phones are connecting just fine) and works again as soon I put the original cable back.
Hi,I have a samsung Note N7000.
I'm have a similar issue,start with high power charging issue every 5seconds.I bought a replacement from ebay company in New Jerse it fixed that problem.but it created a problem when I make a call the other end can not hear me.I email the company and they sent #2 replacement.after
the charging port board was installed now I dont have any signal for service.the pcb# N7000/i9220_sub_Rev1.0.
I'm going try different company.what should I be looking for?I'm wasting too much time on this.
johnson1828 said:
Hi,I have a samsung Note N7000.
I'm have a similar issue,start with high power charging issue every 5seconds.I bought a replacement from ebay company in New Jerse it fixed that problem.but it created a problem when I make a call the other end can not hear me.I email the company and they sent #2 replacement.after
the charging port board was installed now I dont have any signal for service.the pcb# N7000/i9220_sub_Rev1.0.
I'm going try different company.what should I be looking for?I'm wasting too much time on this.
Click to expand...
Click to collapse
Having exact the same problem.. just a moment ago I tried the third board and still hacing exact same problem, no signal or one bar only when I have one bar I can make a call but the other end can not hear me
gregsarg said:
Interesting ....
The part seems okay ...
And the odds of two bad ports in a row is remote at best ....
Some time ago I saw a thread about an extra wire that traveled down from the antenna to the charging port....
And users were reporting that this very small wire was being damaged or missed when the port was serviced.
I've never seen this wire or connection ......but I figured I'd bring it up ..
Try a general search on the topic ...and see if it yields a result.....
I just remember it being a big deal ....g
Click to expand...
Click to collapse
Sorry to bring up an old thread but I wanted to bring this to others attention. What Gregsarg said about a white wire running down from the antenna is correct, or at least it is on an i717. It runs down from the right hand side of the board, behind where the flex board connects and onto the little round connector on the flex board, it's probably that that's been missed off of some phones as would be noticed by only getting 1 bar of signal! I've also noticed that the UK version of the note only has 4 brass connectors on the flex board 2 for the antenna and 2 for the speaker whereas the i717 has 5, 3 for the antenna and 2 for the speaker. I'm not sure what the difference is between a white or black i717 to be honest, i'd have thought it would only be the outer casing that had changed, I can't see them changing parts too, that just sounds stupid!
Anyway, the reason I'm posting is not just because of the above, it's because i'm in the middle of fixing an i717 for someone and was searching to see if a N7000 part would fit and although it looks as though it would I'm not willing to test that theory! I will say though that the missing brass connector is also connected to brass connector 2 on the Ariel/speaker module but on the flex board that connector also has a resistor above it which would likely cause an issue!
The part that i'm ordering is from a company in the UK but is a Rev 2.0 board and not the rev 1.0 that is in it already so i'm hoping that's not an issue else i'm gonna have to buy from China which is cheaper but will likely take an age to get here and the customer wants it done ASAP so what they want they get! I will update this thread once i've fitted the part and got it running along with a link to where I got it from.
h4x0rm1k3 said:
Sorry to bring up an old thread but I wanted to bring this to others attention. What Gregsarg said about a white wire running down from the antenna is correct, or at least it is on an i717. It runs down from the right hand side of the board, behind where the flex board connects and onto the little round connector on the flex board, it's probably that that's been missed off of some phones as would be noticed by only getting 1 bar of signal! I've also noticed that the UK version of the note only has 4 brass connectors on the flex board 2 for the antenna and 2 for the speaker whereas the i717 has 5, 3 for the antenna and 2 for the speaker. I'm not sure what the difference is between a white or black i717 to be honest, i'd have thought it would only be the outer casing that had changed, I can't see them changing parts too, that just sounds stupid!
Anyway, the reason I'm posting is not just because of the above, it's because i'm in the middle of fixing an i717 for someone and was searching to see if a N7000 part would fit and although it looks as though it would I'm not willing to test that theory! I will say though that the missing brass connector is also connected to brass connector 2 on the Ariel/speaker module but on the flex board that connector also has a resistor above it which would likely cause an issue!
The part that i'm ordering is from a company in the UK but is a Rev 2.0 board and not the rev 1.0 that is in it already so i'm hoping that's not an issue else i'm gonna have to buy from China which is cheaper but will likely take an age to get here and the customer wants it done ASAP so what they want they get! I will update this thread once i've fitted the part and got it running along with a link to where I got it from.
Click to expand...
Click to collapse
When getting the part, Revision usually does matter. Also the serial number under the revision number (Usually starting with DRC or DRG) can also matter. Getting the identical one is usually the best bet (albeit not the easiest considering people on ebay use stock images and don't show you the ACTUAL part you're getting.)
KaboodleMoon said:
When getting the part, Revision usually does matter. Also the serial number under the revision number (Usually starting with DRC or DRG) can also matter. Getting the identical one is usually the best bet (albeit not the easiest considering people on ebay use stock images and don't show you the ACTUAL part you're getting.)
Click to expand...
Click to collapse
I got the new part this morning, it was a REV 2.0 board and after putting it all back together including the white/grey ariel wire I can report that it's working perfectly, as good a signal as it had before and is now charging properly. The link to the UK based seller is here for anyone interested that needs a replacement in the UK - http://www.ebay.co.uk/itm/300819833823?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649 The part is £19.99 with no P&P and arrived in 1 day. Just in case the link doesn't work then the name of the supplier is gravedigga1.
EDIT:- I heard back from my customer today who has reported having problems with wifi, signal and loudspeaker! Therefore the Rev 2.0 part won't act as a decent replacement for the Rev 1.0 unfortunately. I wasn't able to fully test as the customer didn't leave his sim card in and he uses 1 of those weird networks which I don't have a sim for. I have managed to source another UK supplier on ebay for an even cheaper price of £12 and they verified that it is a Rev 1.0 board they have in stock and have put 1 aside for me. Once I know that one works for definite i'll report back again just to update the thread but this time the customer is bringing the phone when the new part is here so it can be tested fully before it goes back to him!
I just find it strange that even though the Rev 2.0 is exactly the same in every way as the Rev 1.0 board that it has these issues although i've not heard of the loudspeaker problem before so I think there's a fault with it anyway.
Yeah these notes are getting really dodgy in their old age. We've decided to basically not fix abutting except the screens anymore because getting the right parts is a nightmare.
Sent from my DROID BIONIC using xda app-developers app
This may be a little off key here and if I'm in the wrong thread I apologize but...
I have the i717, bought the charging port off of eBay and replaced it. After plugging in the phone the touch keys at the bottom lit up like I was in business. After allowing the phone to "charge" for about 2 hours, the touch keys were the only thing to work and light up on the phone. I could press the lock key on the side and the touch keys would come off and on like it was on the lock screen but the screen was black. Has anyone encountered this before? If so, please help!
Thank you
Btw, it seemed like the phone was charged/charging bc those touch keys were on...
samsung sgh-i717 usb port
Well I have tried three different suppliers and I have not found a board that works correctly . Some boards that network strength is weak , some boards the microphone doesn't work , some boards that speaker won't play . I have reinstalled my original board back in my phone and every time it returns back to working properly. I just need the USB /charge port to work . Please if you have any ideas let me know ib6469 @ yahoo . com . Thank you very much for or help
Pease Help..i717..charge port
Hello ,
My name is Russ and I have a Samsung Galaxy Note SGH-i717 ( AT&T ) which I love . About two months ago the charge port quit working , so I ordered one from Ebay ( Flex cable , Mic/USB board ) , installed it and my signal was weak after installing it so I reinstalled the original board and it went back to full power . I thought it was a bad board , so they sent me another , I installed board #2 and the speaker on the back had no sound , put my board back in and the speaker went back working . So I had the supplier send me another board #3 . I got it installed , and the Mic wouldn't pick up , I put my board back in everything goes back to normal . So I thought it might be the supplier , so I tried a different supplier , same thing . In total I have tried three different suppliers and I lost count on how many boards I have installed .. Every time I can reinstall the original board and it will stop whatever it's doing wrong . My board Number is SGH_I717_SUB_REV1.0_1107 , DRBL12IN BF , 69 . I am at a lost , I don't know if there's something I'm doing wrong . Thank You for your time ib6469 ( Russ )
same issu
Please let me know if anyone has had any luck finding a board that works... i am in the exact same boat... email me at bnanda0827 at yahoo.com
ib6469 said:
Well I have tried three different suppliers and I have not found a board that works correctly . Some boards that network strength is weak , some boards the microphone doesn't work , some boards that speaker won't play . I have reinstalled my original board back in my phone and every time it returns back to working properly. I just need the USB /charge port to work . Please if you have any ideas let me know ib6469 @ yahoo . com . Thank you very much for or help
Click to expand...
Click to collapse
note charching port
hi
i purchase this part from 6 different company but same problem no signal charging port works ok.
any boby have solution please let me know.its very annoing.
joe
zia_uddin said:
hi
i purchase this part from 6 different company but same problem no signal charging port works ok.
any boby have solution please let me know.its very annoing.
joe
Click to expand...
Click to collapse
So it looks like basically fixing the charge port on a galaxy note just isn't going to hapen if you want service. Nobody has found a solution?

[Q] Root Galaxy S2 At&t without computer

Hi ,
My galaxy S2 is have a problem .... whenever i connect it to a power out / computer the power supply starts fluctuating because of which i cannot use my usb port on my phone to charge so i take out the batter and charge it with an external charger.
Is there any way i can root my phone without connecting it to my computer ?
And one more thing is there anyway i can get my USB port to work ?
I bought this phone when i was in USA but after i shifted back to India this problem started occurring.
The service center people cannot repair or replace it as its the USA version and not the International version.Some parts of International version are not compatible with this US version according to the service center guys.They also said that its IC is short circuited but i think when IC is short circuited the phone does not give display but its working all fine.
Please help me with these 2 things -
1.Rooting my phone without connecting to PC
2.Getting my phones USB port back to work
I'm guessing your USB port has a problem check out this thread
in my case the phones not charging.....
The phone reboots when the charger is connected
The answer to your question is no. Unless I've completely overlooked something.
You will need a good usb port to be able to root the phone. There have been a couple of people who have reported that they successfully replaced their own usb port, and say it is relatively simple to do. It may take a while to get a replacement port, but since the part is small, shipping to India should not be prohibitive. Replacing your own usb port seems to be the only practical fix for your problem.
creepyncrawly said:
You will need a good usb port to be able to root the phone. There have been a couple of people who have reported that they successfully replaced their own usb port, and say it is relatively simple to do. It may take a while to get a replacement port, but since the part is small, shipping to India should not be prohibitive. Replacing your own usb port seems to be the only practical fix for your problem.
Click to expand...
Click to collapse
where can i find a working USB port ?
Google it. Not being rude but damn...
If you have a question about when the next CD by your favorite artist comes out, you google it right? When you need to know where to find which site has the best price on that CD you google it, right?
Use that same logic here. You need a part, google it.
Also, eBay has been known to have items people want to sell that anyone can bid on. Knowing you need it shipped overseas, it would be good to make sure the seller will ship it to your location before buying it.
(Searching these forums will present you with the answer as to which part you need to look for)
Clay
Team Pirate
Sent from my PINK GSwagger2

Trouble Restoring to Stock Nougat from CM 13.0

I'm trying to restore a Nexus 9 (flounder, WiFi) to stock Nougat from CM 13.0-20160924-NIGHTLY-flounder. Problem is, my PC won't detect the device.
I have another Nexus 9, which is running Nougat 7.1.1 and it is neatly detected by the PC as Nexus 9.
I've looked through the developer options and made sure the settings are the same on both devices. I've flipped through the various connection types while connected (charging, media, photo).
I'd appreciate some help unf#cking this situation.
Crike said:
I'm trying to restore a Nexus 9 (flounder, WiFi) to stock Nougat from CM 13.0-20160924-NIGHTLY-flounder. Problem is, my PC won't detect the device.
I have another Nexus 9, which is running Nougat 7.1.1 and it is neatly detected by the PC as Nexus 9.
I've looked through the developer options and made sure the settings are the same on both devices. I've flipped through the various connection types while connected (charging, media, photo).
I'd appreciate some help unf#cking this situation.
Click to expand...
Click to collapse
I saw someone else with that same problem. Turned out to be the USB port. If it turns out to be that, it's an easy repair. Just change the USB daughter board. Couple screws and couple ribbon cables. Takes like 20 minutes, and they're like $12 on eBay.
Explore software solutions first of course. Maybe uninstall and reinstall drivers. Or even try wugs toolkit.
Thanks for the suggestion. Indeed, I read a similar thread with the same solution. A USB board should be on its way from China in the next few days. I was considering buying one anyway as the charging performance has been erratic at best for a while, which might be due to the same basic trouble with the hardware.
I'll update when the replacement board is in and installed in a couple of weeks.
Crike said:
Thanks for the suggestion. Indeed, I read a similar thread with the same solution. A USB board should be on its way from China in the next few days. I was considering buying one anyway as the charging performance has been erratic at best for a while, which might be due to the same basic trouble with the hardware.
I'll update when the replacement board is in and installed in a couple of weeks.
Click to expand...
Click to collapse
I changed mine too (also from China). Mine was affecting otg connection. Fixed it right up, took about 20 minutes. I'm no pro either, only other hardware repair I've done is the screen on my n7 (2013).
Replacing the USB board fixed the problem.
Crike said:
Replacing the USB board fixed the problem.
Click to expand...
Click to collapse
Good to hear

Categories

Resources