bluetooth has stopped since last software update LG-G5
i tried to clear cache, rest phone, remove and add the device.
nothing works, every time i try to connect the bluetooth in my car i got this message "bluetooth has stopped" and the bluetooth connection goes on and off.
Related
Hello all,
Most of the time when I connect my Note to my MINI with MINI Connected (Nav, Pandora interface, Vehicle diagnostic interface, etc), it reboots the phone. It's not instant, sometimes the music will start playing, the car will confirm that the phone directory is updated, and I might even receive a message, but it usually reboots at some point. Once it reboots it usually is ok for the rest of the trip, even after disconnecting and leaving the car.
Yesterday, it started rebooting after disconnecting as well; once again, not every time...just did it yesterday at the mall and this morning when leaving my car for work.
This morning after it rebooted when leaving the car for work, I turned off the voice talk "Connect on Bluetooth" option to see if that does anything, but I thought I'd check to see if anyone has heard anything else.
Thanks!
Update:
So yesterday I rooted my Note and loaded Titanium backup and froze some services I thought might be causing issues. NOGO there.
I also repaired the phone as my primary (which syncs the phonebook) phone and with media audio. NOGO.
Next I repaired with just audio. NOGO
This morning I repaired as a secondary phone (no phonebook). So far so good. On the ride home today I'll pair as primary phone again and see if it stays.
Hi
I have a parrot handsfree MKi9200 installed and it's been working fine. But since 3 latest updates on my S II, it's been acting odd. I'm now at version 4.0.4.
Problem is when connecting to the parrot it's ´stuck for some 20-25 seconds. When it's done doing whatever it's doing i get a message on the phone in a grey boks.It's in danish, but it's something about bluetooth has stopped syncronization. I have to press OK on the phone to get grey boks to dissappear. This also happens if i call someone and obviosly at some point hang up, then i get that odd message again and phone is stuck until it has done "something". On the display of the parrot device, i see the symbol for sync running while it's going on.
Is it some Bluetooth setting i need to tick somewhere that has been enabled within last 3 Android updates?
Cheers
Rathsach
It maybe that the parrot bluetooth software needs updating. Check your manual to see how to updae the software.
Bluetooth updates on the phone download newer versions of the sofftware which may not be compatible with the version of the parrot.
I have a Cubot One, using the G800_CUBOT_D1_V0.8_20140124_MJK firmware (4.2.1) - it was previously on the 0.6 firmware and had the same issue.
What I have experienced is that when connecting to a device with Bluetooth - in this case a Sony SW2, but have also tried Bluetooth headsets - it has problems pairing.
The phone sees the BT device as an available device, and when I select it, it starts the pairing process. Initially it seems to be ok and successfully pairs for 2-5 seconds, the the device is relisted as an available device, but not connected. I have had success twice. The first time was immediately after rooted my phone, and this was ok for several days, even rebooting my phone and the watch didn't seem to cause the issue again, but then it randomly stopped working. I was unable to connect until flashing with the 0.8 ROM. At this point is was again working for about 24 hours - even better than before - until I switched the watch off. Since then I have been unsuccessful in pairing again.
Interestingly, when I try to pair with my Galaxy Tab 2 I have the same problem, UNLESS I initiate the connection with the tablet, then it is fine.
I know that there were problems with the Bluetooth stack on 4.2.1 when it first came out, and it may be related to that, but can anyone offer suggestions as to what else I can try?
So I bought a Ticwatch 2 the other day
It stopped receiving notifications this morning, and so I decided to try resetting it and starting fresh.
I reset the watch, so it needs to be set up again, but it is still showing on my Bluetooth list. If i hit unpair on bluetooth, it just automatically pairs with the watch again. So I am now stuck in a loop of not being able to set up as the watch isn't reflecting it is connected to the phone, the app on the phone shows it isnt paired, but Android says it is connected and I can not possibly disconnect it.
I have tried clearing bluetooth cache and restarting the phone, and it always just connects right away.
Is there a way to force the phone to stop recognizing a bluetooth device?
Reset network settings ... gonna erase all BT/Wifi etc ....
I would say that or just rename it and then try to unpair the watch if it keeps trying to connect
Android Auto has stopped working. I have a Galaxy Fold 3 that I have been using since November with the Uconnect in my 2018 Jeep Compass. It suddenly stopped working. It worked fine until today. I last used it about 2 weeks ago. The phone connects with the car via Bluetooth just fine. I am able to make calls and receive texts. When I connect the phone using my USB cable to use Android Auto, the phone shows that it is charging and I verified it is set to be able to transfer data. Instead of launching and connecting to Android Auto, the screen on the car tells me to follow directions on the phone screen to connect. The phone screen shows an Android Auto screen that shows it wants to start set up to connect (it used to connect without any issues) but when I hit the "next" button on the phone, Android Auto on the phone just shuts down. I cleared the cache & data for Android Auto, uninstalled & reinstalled Android Auto, verified my phone has all of its software updates, tried a different USB cable, reboot my phone, unpaired & then paired the phone to the car... nothing is working. My phone software updated on August 2nd. This is the first I've tried to use the Android Auto since the last phone software update. I've tried all of the suggestions on Android Auto's troubleshooting page. Can anyone help?