Related
So i dropped my phone and looks like i need a new digitizer. I have tear down the phone and the last thing i need to do is remove the digitizer but i have no idea on how to do it. Does anyone have any tips or links that show you how to remove it? I've seen this video http://www.youtube.com/watch?v=t8u5Wa3Odak but it doesn't show how to remove the digitizer. Any help would be really appreciated
Painkiller006 said:
So i dropped my phone and looks like i need a new digitizer. I have tear down the phone and the last thing i need to do is remove the digitizer but i have no idea on how to do it. Does anyone have any tips or links that show you how to remove it? I've seen this video http://www.youtube.com/watch?v=t8u5Wa3Odak but it doesn't show how to remove the digitizer. Any help would be really appreciated
Click to expand...
Click to collapse
At the end it shows you to heat up the digitizer to losen the adhesive that is holding it in place all around the edge. After that, slowly pry around. Do it really slowly though and let it work itself off, and don't use a sharp object because it will damage the sensitivity of the digitizer. Really patience is key. Don't rush it like I tried to the first time also be careful of the lcd underneath.
Just to reiterate what was already said, pry very gently, don't stick whatever pry tool you are using too far into the device, the LCD below will crack so easily. I did it when I did mine. Have patience, take a lot of time slowly working it off the adhesive little bit by little bit. There isn't any magic trick to this, it takes a lot of time and practice.
Hi everyone.
<SKIP> (if you don't like reading a lot)
So, I managed to do a very silly thing *slaps own wrist*. After spilling some food on my brand new pair of shorts, I chucked them straight in the washing machine without thinking. After about 5 minutes, I noticed a slight knocking noise coming from the washing machine, and alas, when I dug my hand in the water to try find the culprit item, I pulled out my drenched SGS2.
Now, as any technically-minded person does after such an incident, I immediately pulled out the battery, SIM card and memory card, and went sifting through my kitchen for rice. It was in the sealed bag of rice for about 1.5 weeks, after which I tried to turn it on. It worked! However, the touch screen wasn't responding, so bag into the bag.
Closer to two weeks, I took it out again. This time, everything seemingly worked fine! I did however notice while using the back camera that some residue from the water has stuck onto the rear camera lens. It also took me a while to notice that the bottom microphone isn't working, which defeats the point of having a phone.
Everything else works fine. I took it to a local repair shop (which I'm a bit doubtful of) and they came back to me saying they couldn't do anything.
</SKIP>
So, in conclusion, the bottom microphone isn't working (people can't hear me during calls), and the rear camera lens has residue on it (which can be seen when using the camera):
1) Assuming the warranty is now void due to water damage, do you think I should try my hand at replacing the microphone/USB board on my own? Has anybody done it, and has some pointers? Anyone know a good place to get these?
2) Is anyone aware if the camera area can be broken down to such a point that I can wipe the residue off the lens?
I'm tempted to just take it to another repair shop for them to try - really don't want to go to Samsung though, as they'll likely charge a small fortune.
Thanks for the help in advance,
MrP.
MrPadie said:
Hi everyone.
<SKIP> (if you don't like reading a lot)
So, I managed to do a very silly thing *slaps own wrist*. After spilling some food on my brand new pair of shorts, I chucked them straight in the washing machine without thinking. After about 5 minutes, I noticed a slight knocking noise coming from the washing machine, and alas, when I dug my hand in the water to try find the culprit item, I pulled out my drenched SGS2.
Now, as any technically-minded person does after such an incident, I immediately pulled out the battery, SIM card and memory card, and went sifting through my kitchen for rice. It was in the sealed bag of rice for about 1.5 weeks, after which I tried to turn it on. It worked! However, the touch screen wasn't responding, so bag into the bag.
Closer to two weeks, I took it out again. This time, everything seemingly worked fine! I did however notice while using the back camera that some residue from the water has stuck onto the rear camera lens. It also took me a while to notice that the bottom microphone isn't working, which defeats the point of having a phone.
Everything else works fine. I took it to a local repair shop (which I'm a bit doubtful of) and they came back to me saying they couldn't do anything.
</SKIP>
So, in conclusion, the bottom microphone isn't working (people can't hear me during calls), and the rear camera lens has residue on it (which can be seen when using the camera):
1) Assuming the warranty is now void due to water damage, do you think I should try my hand at replacing the microphone/USB board on my own? Has anybody done it, and has some pointers? Anyone know a good place to get these?
2) Is anyone aware if the camera area can be broken down to such a point that I can wipe the residue off the lens?
I'm tempted to just take it to another repair shop for them to try - really don't want to go to Samsung though, as they'll likely charge a small fortune.
Thanks for the help in advance,
MrP.
Click to expand...
Click to collapse
I replaced the earpiece (speaker) in my HTC HD2. It was a pain in the ass to tear down. I imagine that my SG2 would be even harder.
I found the earpiece on ebay for only about $10, and it even came with a few tools needed for the tear down (plastic pry tools). It was not for the faint of heart...meaning that I was stressed to the balls, and wasn't sure until it was over if I had destroyed my phone. So the microphone should be possible to replace, if you're careful and technically inclined.
The camera will also probably need to be replaced (although, you might find otherwise when you take it apart). The good news is that it shouldn't cost more than $20, but I have no idea really...just estimating. Here's a link to a guy's G+ post who did it click me.
If you look on google, you'll find youtube videos about the tear down and how to do it.
I'd watch those first to check the difficulty. I think I've also seen instructions somewhere, but don't remember exactly where.
Good luck. Stay calm and be careful.
UPDATE: So, the digitizer I bought developed a massive dead zone. I already contacted the amazon store I bought it from, they're replacing it for me. Why does this matter? Because now I get to update this post with pictures/video! So, yeah, I guess this guide should get a lot more helpful soon.
Update 2: Ok, so, I don't even know how to express my anger and frustration. This girl at work shoved my phone out of my hands and into the leg of a table, completely destroying my phone. So, yeah, sorry, I guess I won't be updating with pictures/video, because the amazon store isn't going to take the screen back now.
Yo, guys. If anyone noticed that I was gone, I'm flattered, since I don't post a lot. But yeah, I havent had my Optimus G in about a month, so I havent been on this forum. In that time, I went through my Second Motorola Atrix HD, a broken Galaxy S3, and even lived through Google Voice on my computer. It's an extremely long story, and kind of ridiculous, so I'll spare the details.
HOWEVER, I did finally just buy a replacement Digitizer and LCD screen, and successfully installed it, and I want to share tips for anyone doing it themselves.
When removing the back, after you've removed torx screws, start prying the back off from in between where the Sim card and MicroSD go. Where the back of the phone and the chassis of the phone are separate is much more obvious in that cavity, PLUS dents/dings from jamming a screwdriver in there wont be noticeable when you put the bay cover back on.
Don't force anything off. Make sure you've removed every screw, unclipped every clip, and removed ribbons from everything you're trying to take off.
Removing the battery is tricky. Be careful not to deform it too much, cause that's dangerous. But there are 2 strips of double sided tape running horizontally beneath the battery. Try to get something between the top one and the battery, then carefully pull the battery off the second strip with your hands. sticking too much stuff beneath it to pry it up is going to cause some trouble, so lifting it with your fingers might be better.
Remove the motherboard. detatch all the ribbons, antennae, everything, then pull up from the left, then slide left and out. This is how I got it out with the least resistance, but there is no science to it. If you've gotten this far, you can figure out how to pull it out without breaking it in half.
Components that need to be removed before LCD+Digitizer removal:
Motherboard
Battery
Camera
Just put them off to the side, you don't want them damaged during the next part.
WARNING! If you plan on saving your LCD screen, DO NOT DO THIS. The high heat will cook your screen and make it unusable. Only do this to remove a broken or unsavable Digitizer+LCD.
Alright, now pull out the heat gun. Alternatively, you can do what I did, and use a hair dryer. Not even kidding, this will work fine, and will be hilarious when you tell your friends about it.
On a high heat, start heating the screen. If you're using a heat gun, just do your thing, you know how it works. Hair dryer folks, keep the dryer very low to the phone, low enough to feel the dryer being pushed up by the air, holding it just high enough so it sort of hovers. (You'll know what I mean when you try it. If you don't, just keep it about half an inch off the phone.) Move the dryer along the edges of the screen, all the way around, thats where the glue is. It should heat up pretty fast.
Using your pry tool, start at the speaker grill and pry all the way around the phone. lifting just slightly upwards. If it's not extremely easy, apply more heat. Work all the way around, then pull the screen off. Be careful, it's likely you'll shatter the screen even more at this part if you're not careful. User Bozwell had an excellent suggestion (post 4), cover your screen in tape, then begin separating the screen to keep from getting glass everywhere. Great idea, Boz!
Alright, so from here on out, it's just reassembling your phone correctly. Piece o cake.
Firstly, put your new screen in. If it came with adhesive, it's up to you if you want to apply it now. I'd think you probably have to, but up to you.
If you're like me, and no adhesive was provided, hold off on doing anything for now. Just put the screen in the hole, and thread the ribbons through.
The motherboard lines up with some contacts on the chassis in a few places, but most importantly, there is a connection on the top left corner of the body, and the UNDERSIDE of the motherboard that needs to be made. I believe it's proximity sensor, but not sure. It's very difficult to tell if its attached, but look at what I'm describing, and try your best to mate them.
Don't forget ANY cables. Like, that's pretty obvious, but even when you're sure you didnt forget any, check again. The camera's ribbon is underneath the screen's, don't forget that one. I reassebled the whole thing, everything was working perfectly, except I no longer had any mobile connection. I couldn't imagine what I'd broken, since that's a whole different area, but going to phone status and checking my signal strength revealed I forgot to reconnect the white antennae (status showed my signal at -200,000 dbm). So, double check, because the more often you have to reopen your phone, the more flimsy it's going to get.
Alright, screw the plastic shielding back on, reconnect your battery, then flip the phone to be face up. Power it on, test the screen to make sure it's functional. If all is well, power off and glue the screen in. What I did, and I welcome anyone to tell me a better glue type or method, is plain ol Super glue along all the edges where the old glue was. Press it in, flip it over, and while it's drying, finish reassembling the phone (should just be make sure everything is screwed in inside, then put back glass back on.
If your screen wasn't functional, I guess try to get it replaced by whoever you bought it from, and leave your phone disassembled for when it gets to your house.
Alright, that's pretty much the thick and thin of it, it genuinely isn't that hard of a replacement. I've done a number of digitizer/lcd replacements, not bad at all. I hope this helped anyone stuck or wondering about anything. This video can be used as a rough example, but it goes really fast.
Good Luck!
replacement of lcd/digitzer
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
gruiz3 said:
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
Click to expand...
Click to collapse
Haha that's crazy, it bothers me how fragile this phone seems to be.
To keep the glass shards from going everywhere try covering the screen in tape before you start.
bozwell said:
To keep the glass shards from going everywhere try covering the screen in tape before you start.
Click to expand...
Click to collapse
Great idea, OP updated!
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
MoFoQ said:
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
Click to expand...
Click to collapse
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
ripin150 said:
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
Click to expand...
Click to collapse
I figured...though I've been eye-ing using the screen+digitizer+front housing if and when they get back into stock.
(digitizer only is also out-of-stock)
Hello,
Something happened to my watch. I opened it to install an SD card. I did as the instructions says, carefully. The rubber gasket was well placed and I tightened the screws the maximum I could, with the provided screwdriver. I guess it would not be tight at all, because, although it has been wet three times and anything happened, Yesterday it was exposed to sweat for a while, and then washed the same way like previous times. Today it worked well all the morning, but around noon, I saw it appeared many stripes on the screen and checking the clock externally I've finally seen condensation into the lens, so I guess, obviously, that moisture has entered inside the watch. I've opened the watch, remove battery and SD card, and then introduced it into rice, using an airtight container to try drying it.
Lens condensation has disappeared, but in the display is still appearing lines.
I wonder what can I do, who should I contact for assistance to repair, where should I send it for repair in case I can't revive the screen, because as I think, this type of damage is not covered by warranty.
I am disappointed with this device because of this. It should not be so complicated to close it and to keep it well sealed. Its design in this particular point is disastrous. I can ensure that the rubber seal was installed properly, and the only thing I can imagine is that the screws do not stay tight properly, but I repeat that I tightened it all the way I could, strongly, until the limit of not to damage the screw heads, and checking for the joints are well sealed. If I finally can fix the watch, the next time I need to open the back cover, I'll pre-tighten it with a sergeant tool before tightening the screws... it seems to be necessary...
Thank you for your help.
It is ruined. Sell it for parts maybe. A shame.
Sent from my Nexus 5 using Tapatalk
lanzas said:
If I finally can fix the watch, the next time I need to open the back cover, I'll pre-tighten it with a sergeant tool before tightening the screws... it seems to be necessary...
Click to expand...
Click to collapse
This is a waste of time. There is no way to make the existing case waterproof - not just the two screw openings but also the antenna, speaker, microphone and buttons are all possible routes for moisture ingress.
One look at the SIM cover and its pretend gasket convinced me of this. There is not enough structural integrity to ensure a good seal. The gasket will not be compressed in a way that makes a watertight seal - over tightening might even make things worse by deforming the plastic.
If you ever get it to work again, keep it dry.
lanzas said:
Yesterday it was exposed to sweat for a while, and then washed the same way like previous times.
Click to expand...
Click to collapse
It's not a very good idea to wash an electronic device that has no water / moisture protection what so ever (the seals don't do much good, and there are lots of other gaps in the watch where water can get in). Sometimes devices can recover when dried completely. Maybe put it in a bag of rice, that's great for absorbing moisture... But most likely, it's dead.
It is supposed to be a waterproof watch...
Definitely the screen is broken. The watch works fine, but the screen shows a lot of lines that don't allow clear visualization. No one from Omate answered my email...
I feel cheated... and silly...
You WERE cheated, we all were. Don't feel silly though, you were misled by a pro.
You might possibly be able to replace the display with an iPod Nano display, but I don't know anyone who has and an iPod Nano display might be worth more than your TrueSmart.
Sent from my Nexus 5 using Tapatalk
Yep. Kid got a hold of it before case arrived. Yes its my fault. Should have kept better eye on him. There are only two bids on YouTube. Neither one is great. I see on eBay they have LCD and digitizer and housing. From vids it looks easy. But would like to hear from anyone who has done it. Thanks
So sorry for the breakage. Here is a video that seems pretty good, https://www.youtube.com/watch?v=qm6NwBvo6T0. The process doesn't seem to hard, to me. Good luck.
kimtyson said:
So sorry for the breakage. Here is a video that seems pretty good, https://www.youtube.com/watch?v=qm6NwBvo6T0. The process doesn't seem to hard, to me. Good luck.
Click to expand...
Click to collapse
I recently replaced the LCD screen on a OnePlus One, other than the size, it was almost identical to the Mate2. couple parts in different spots but it had enough of those #%(@!)% rice grain size screws that I put them on a magnet, to make sure I didn't lose them.
Yes. That is one of the vids I was talking about. The other one was actually for a mate. Not mate 2. The thing I don't understand on this video is he never actually gets to the part of the screen replacement. So, I am presuming that with this phone as long as I purchase the LCD+digitizer+frame. Then it will just be a matter of putting all the parts including board back in to it. On eBay there are choices. You can purchase just the glass or glass and digitizer or those plus what they call the frame. While on my phone. Only the outside glass is broken. I am going to buy the kit that has all three. I would give just replacing the glass a shot if I could find a video or tutorial. I have looked everywhere. Nothing. The closest thing I could find is the vid on youtube of the guy changing just the glass on his mate. Unfortunately, he never says a word in that vid. I guess it's just to show it can be done. I'm really stressed by all this. I would prefer to just change the glass if only I could find some info. I presume it is like a Samsung where glass is glued with local to digitizer. I have fixed those type on a s3 and note 2. Was not that hard. Just be sure to heat properly and don't scratch digitizer. With no idea of how it is done on this phone. I guess I will get the kit and hope for the best as of course. It has to come from China. Waiting....Thanks for the info and I will do my best to make a vid so others can learn from my mistakes? Lol or hopefully success.
Have a hair dryer or a heat gun handy just in case. On the OnePlus, the screen is "glued" somewhat, to the plastic frame. It is a LOT easier to separate if you heat is up a
bit. Just heat one side, then you the (as I like to call it) guitar pick tool to start to pry it up, then to a little more at a time, so you don't overheat the broken screen.
After you get the screen off, make sure you scrape around the edges of the frame, to ensure you remove any sticky residue. You don't need to heat up the new screen. Once you press it down, it will stick quite well.
If it were me I would get the entire kit and be done with it. There is too much that can go wrong with the hairdryer and peeling the old, broken screen from the digitizer. With the kit, it's just all screws and dismantling then put it back together. Much easier.
I hope that is right about the kit. The thing that scares me is what will the quality of the parts be like? I know my digitizer is fine. So I'm going to try the kit first. If it fails due to bad parts. Then I will still have the option of just doing the glass. The cheapest I saw for the glass was 18.00 bucks. The kit with shipping was 58.00....Not really a huge difference. Again its the quality of the parts that scares me. Of course the vid on youtube makes it look easy. But I'm sure he is doing it on a phone that has been torn down a few times. Its always easier then. As I said. I intend to video all this. If nothing else. There will at least be more info available to poor suckers like me..lol. Will see in a couple weeks if the Chinese ship time holds true...
I'd bet the quality is the same as OEM.
Sent from my MT2L03 using XDA Free mobile app
One other thing. Just wanted to ask. You say the one plus is about the same? Are you saying that because there similar in how their made? Or do you know something about where their made. Thanks for the info on the glass. I have done it on Sammy phones. Has to be similar. Kit is already coming. So I'll go that route first try. Wish your repair had been on a ham2. Then I would feel better. I guess I get to go first. Lol
kimtyson said:
I'd bet the quality is the same as OEM.
Sent from my MT2L03 using XDA Free mobile app
Click to expand...
Click to collapse
The one I ordered for the OPO looked identical, except the routing for the lcd screen connector was just a little different, but in no way caused a problem.
I wanted to update you guys on how the repair of my screen is going. I have some info to share and trust me. It is important if you ever need to DIY on this phone. Most are aware of the video on youtube. Ive watched it several times and I always got the feeeling it looked to easy. Well, my screen and dig assy came in today. I was going through the process of tearing it down and everything was going well. Untill i got to the part where you remove the power button cable. The one that runs along the side of the phone. I SHOULD HAVE KNOWEN. In his vid. He makes it look like this cable will come off with gentle pressue. BULL****. It wont. It is glued Tight and you will just winde up tearing it. I am so pissed. I wish he would have just said to buy the cable with the kit. Its 10 bucks on ebay of course. So, now I have a torn down phone waiting for the cable. I was making a video of the repair. When the cable comes in. I will finish it and upload to youtube. The other thing he makes look easy is the removal of battery. Again, its not and you could damage it too. But I managed not to. Anyway i am really upset right now so sorry for cussing. I want to find that dude and shake his hand and smack him at same time...
pckarma112 said:
I wanted to update you guys on how the repair of my screen is going. I have some info to share and trust me. It is important if you ever need to DIY on this phone. Most are aware of the video on youtube. Ive watched it several times and I always got the feeeling it looked to easy. Well, my screen and dig assy came in today. I was going through the process of tearing it down and everything was going well. Untill i got to the part where you remove the power button cable. The one that runs along the side of the phone. I SHOULD HAVE KNOWEN. In his vid. He makes it look like this cable will come off with gentle pressue. BULL****. It wont. It is glued Tight and you will just winde up tearing it. I am so pissed. I wish he would have just said to buy the cable with the kit. Its 10 bucks on ebay of course. So, now I have a torn down phone waiting for the cable. I was making a video of the repair. When the cable comes in. I will finish it and upload to youtube. The other thing he makes look easy is the removal of battery. Again, its not and you could damage it too. But I managed not to. Anyway i am really upset right now so sorry for cussing. I want to find that dude and shake his hand and smack him at same time...
Click to expand...
Click to collapse
I have worked on several phones. None are easy really. Most all companies use some type of adhesives. Alot glue the batteries in as well. Dunno if you tried it but heat seems to help with the glue. Seen a guy do it with a hair dryer. Worked for me as well with a screen replacement. Never took one of these apart so I have no idea if they use heat activated glue or not. Good luck!
Well Thanks for reply. I too have fixed a few. As long as I have something to guide me. Im Cool. Vid or written indtructions. Yes all phones use some sort of glue. With this one on the cable. Heat would not have helped. You would just melt the cable. I was expecting some adhesive. But not like this. This was not meant to be reused. Period. Thats my point. I wish he would just have said buy the cable. No way it is coming off in one pc. The speaker is also glued down extremely tight. I think I got it. Its still in one pc. Interesting enough. There also on ebay.
I really just want people to know about the power cable. If you have to replace screen on this phone. Get one. Your gona need it. Now it may be middle of july by the time I get the cable. I went ahead and tore everything else out of phone. Tomorrow I will put all back into new assy. But i wont know if it worked till cable gets here. I forgot to record taking out the other pcs. I was just to stressed. But I do have some good vid for most of it. Gripe is now over. il be back when cable gets in...
pckarma112 said:
Well Thanks for reply. I too have fixed a few. As long as I have something to guide me. Im Cool. Vid or written indtructions. Yes all phones use some sort of glue. With this one on the cable. Heat would not have helped. You would just melt the cable. I was expecting some adhesive. But not like this. This was not meant to be reused. Period. Thats my point. I wish he would just have said buy the cable. No way it is coming off in one pc. The speaker is also glued down extremely tight. I think I got it. Its still in one pc. Interesting enough. There also on ebay.
I really just want people to know about the power cable. If you have to replace screen on this phone. Get one. Your gona need it. Now it may be middle of july by the time I get the cable. I went ahead and tore everything else out of phone. Tomorrow I will put all back into new assy. But i wont know if it worked till cable gets here. I forgot to record taking out the other pcs. I was just to stressed. But I do have some good vid for most of it. Gripe is now over. il be back when cable gets in...
Click to expand...
Click to collapse
With any luck you may save someone else a headache!
pckarma112, so sorry for your frustration. Thanks for sharing your experience.
I was going to suggest the the same thing as Moody. Heat from a hair dryer usually helps soften the glue but isn't enough to destroy anything (usually).
Just so we are all understanding, can you show a pic or provide a link of what you purchased? Was it just a screen or an assembly?
Again, sorry for your issues. Hang in there.
Parts
Yes I can. That is if I can post links. So Il try. This is the link for the power cable: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItemVersion&item=291410104104&view=all&tid=1181571120019 This I just ordered yesterday. The deleivery is anywhere from middle of July to second week of August. Im keeping my fingers crossed that I got a good vender and will get a good one. They say they have already shipped it and gave me a tracking number. But the number is not showing up yet. Ive seen this before with china stuff. I will give it a couple days and check again.>... The next one is for the screen kit: http://www.ebay.com/itm/141653108269?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT > Cant say enough good things about this vendor and kit. It looks and feels outstanding and I recieved it in two weeks from china. That is pretty darn good. Now, the only thing is since I have no power cable. I do not know for sure if I got a good one. But, like I said. It feels like a quality part. The last item is a phone repair kit that really helped with this job. The metal and plastic spudger really helped with battery and other small parts like camera and vibrator. For the price I suggest you get one. Here it is: http://www.ebay.com/itm/111501320079?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT
As for the screw driver. Dont do what i did. I bought a cheapo 1.69$ one. It was crap. Lucky for me. I had one from a previous kit I bought and it worked fine. Hopefully these links will show up for you guys. If not I will try with a different browser.
Just so its clear. I do have a hair dryer that I keep for samsung screens. I thought about trying it on the cable. But I have worked on these kind before. There is a really fine line between warming the glue and melting the cable. This sucker had enough glue to hold the hoover damn together. Ive seen it before and Im pretty sure you would melt cable before the glue would give away. Thanks you guys for advise and just letting me vent. I do hope that anyone who attemps a repair can learn from my mistakes....lol. Thanks again.
I've been taking stuff apart and SOMETIMES successfully getting it back together for over 40 years, sometimes with the odd screw leftover, but hey, where do our extra screws come from eh?
I replaced the screen on the OnePlus for a friend a couple months ago and WOW, they need to make these screws JUST a LITTLE smaller, don't you think? I find that keeping a small magnet on hand comes in handy to keep track of those tiny a** screws.
pckarma112- Nice job on the post of Parts. Only problem is the first link failed. Said it was too old. Again, thanks for sharing and letting us learn from your mistakes.
Thanks for the *cough* compliments. The link is bad because seller is sold out. However, you can try this one:http://www.ebay.com/itm/111501320079?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT......If that does not work then there is this:http://www.ebay.com/itm/Black-LCD-D...412?pt=LH_DefaultDomain_0&hash=item3f3f160554 This is same only black. Again, these people really treated me well. Im sure there will be new auctions when he restocks. There are also plenty of others. Price varies a little. Im really delighted that you find small screws to be a pita. Thats just awsome. lol Keeping a piece of tape on the table really helps. Just drop them on to the tape and I promise you will never lose another one. I would really like for this thread to be helpful to anyone that gets unlucky. So, I am trying to be ernest about it all. That includes honesty with no hidden attitude. When I say thanks. I really mean it.
By the time and god willing the power cable arrives. I will hit the big 60. This will not be the last phone I ever repair( I hope). But it sure has been one of the most interesting. Thanks again guys and may your screws never be loose.
Thanks
p51d007 said:
I've been taking stuff apart and SOMETIMES successfully getting it back together for over 40 years, sometimes with the odd screw leftover, but hey, where do our extra screws come from eh?
I replaced the screen on the OnePlus for a friend a couple months ago and WOW, they need to make these screws JUST a LITTLE smaller, don't you think? I find that keeping a small magnet on hand comes in handy to keep track of those tiny a** screws.
Click to expand...
Click to collapse
Thank you. You gave me a good laugh and it was much needed today. In fact. Its needed everyday in this world. The kit of screw drivers that I own are indeed magnetized. Thank God. Seriously though. If you think these are small. Try repairing a watch. Now your talking micro. I have worked on about a dozen or so with my brother. He is a master clocksman. Makes good money still and when ever he needs help. I get to learn from him and make a little too. So, Im blessed. I also lost track of where a couple screws will go on this phone. But, got it figured out. It is nice to know that none of us are perfect. Thanks again bro.