Related
Hi, I have a problem, I was flashing my s2 by Cwm recovery, did all the wipe and factory data, and then went to install the rom, but did not recognize the sdcard, and there was where save the rom, then use odin, to install the rom, since the phone would not start, install 2.3.6 with all files ("pit", "PDA", "Phone" and "csc" and the three boxes checked ("re-partition", "RBOOT self "and" f. reset time ") the process lasted almost five minutes and already finished, waiting two minutes thought this was over, and spent more than 30 minutes and nothing, disconnect and remove the battery, and now only comes in "Download Mode" and when I turn in "recovery" I get a celulara, a yellow triangle and pc "says" encountered an UPGRADE FIRMWARE ISSUE. PLEASE SELECT RECOVERY mODE iN KIES & TRY AGAIN. "
I can only enter download mode, and I have so:
ODIN MODE
PRODUCT NAME: i9100
CUSTOM BINARY DOWNLOAD: YES (1 COUNTS)
CURRENT BINARY: CUSTOM
but since the pc does not recognize it, before the sound reproduced pc to connect the phone and no longer does, hence not able to do anything eh, I do.?
leei in a forum that the cell is still alive and is a single failure, but can not find solution working.
this user also also had the same problem, but the mode excepciopn reconicia download the pc
http://forum.xda-developers.com/showthread.php?t=2374594
sorry for my bad English, I'm Latin American, and had not
try to get to cwm and do a wipe/factory reset
or get a usb jig
p.s. are you sure you placed the files on the right places while flashing via ODIN ?
S2 brick
wishmas7er said:
try to get to cwm and do a wipe/factory reset
or get a usb jig
p.s. are you sure you placed the files on the right places while flashing via ODIN ?
Click to expand...
Click to collapse
Can not enter Cwm, when I try to get out, the celulara, the yellow triangle and pc, if put the files fine. I can only enter download mode, but the phone does not connect to pc, eh tried on other computers and also, that I can do?
Did you try to flash a custom rom with odin?
Look for "forced download"
Sent from the little guy
Hi,
So i tried to update my galaxy s6 edge t mobile to the latest firmware and once it did, it got stuck in the samsung screen and wont boot. The phone was rooted before, and now it just stays stuck. I have restarted the phone and now I have tried flashing the phone using Odin. It keeps saying failed and it shows the following:: " SW REV. CHECK FAIL. DEVICE: 2, BINARY: 1". I have tried downloading the firmware but it just keeps failing. When it updated, it should have updated to 5.1.1 since thats the latest which means i cant just put any other one right?
I dont know what to do to be honest, if anyone can help me i would really appreciate it.
anyone?
Have you tried using Smart Switch to restore Stock firmware?
There are a few solutions mate
1st One:
1) Put your phone into download mode using "Volume Down-Home-Power" combo until your screen comes into download mode and still hold it untill the screen goes off.
2)Quickly switch to recovery mode using "Volume Up-Home-Power" in the black screen and get into recovery
a)if it loads something and says erased... please start from the 1st step again
3)Wipe cache/ factory reset do these things in the recovery mode then reboot.
you should be good to go. If not theres another solution.
--------------------------------------------------
2nd One:
1)Put your phone into download mode.
2)Connect ur phone to the computer via usb and open smart switch
3)Press view more button on the right top.
4)Choose the 1st option as "emergency recovery and restore"
5)Put your model and serial number (its on the backside of the phone)
6)then follow the instructions of the smartswitch
thats it
vanderax said:
There are a few solutions mate
1st One:
1) Put your phone into download mode using "Volume Down-Home-Power" combo until your screen comes into download mode and still hold it untill the screen goes off.
2)Quickly switch to recovery mode using "Volume Up-Home-Power" in the black screen and get into recovery
a)if it loads something and says erased... please start from the 1st step again
3)Wipe cache/ factory reset do these things in the recovery mode then reboot.
you should be good to go. If not theres another solution.
--------------------------------------------------
2nd One:
1)Put your phone into download mode.
2)Connect ur phone to the computer via usb and open smart switch
3)Press view more button on the right top.
4)Choose the 1st option as "emergency recovery and restore"
5)Put your model and serial number (its on the backside of the phone)
6)then follow the instructions of the smartswitch
thats it
Click to expand...
Click to collapse
gonna try that one out
vanderax said:
There are a few solutions mate
1st One:
1) Put your phone into download mode using "Volume Down-Home-Power" combo until your screen comes into download mode and still hold it untill the screen goes off.
2)Quickly switch to recovery mode using "Volume Up-Home-Power" in the black screen and get into recovery
a)if it loads something and says erased... please start from the 1st step again
3)Wipe cache/ factory reset do these things in the recovery mode then reboot.
you should be good to go. If not theres another solution.
--------------------------------------------------
2nd One:
1)Put your phone into download mode.
2)Connect ur phone to the computer via usb and open smart switch
3)Press view more button on the right top.
4)Choose the 1st option as "emergency recovery and restore"
5)Put your model and serial number (its on the backside of the phone)
6)then follow the instructions of the smartswitch
thats it
Click to expand...
Click to collapse
Ok so my phone stays stuck in the samsung screen and smart switch stays stuck saying connecting to your device. i really dont wanna try the factory reset thing because i havent backed up the files on my phone
Ok so i got to flash it with 5.1.1 using odin but once its done it keeps staying stuck in the samsung logo screen....again.
Just did factory reset and still gets stuck at the damn samsung logo..
I am willing to pay if someone can help me solve this issue
I also noticed that once the downloading portion of the phone is done, it says installing with the android robot picture, then halfway it says erasing and then it restarts and gets stuck at the samsung logo
=(
you need to do wipe cache and, wipe data and factory reset. That erasing part is normal. Your phone is not bricked. That android robot portion just verifies the stock recovery and partitions. No problem with it. just wipe cache dalvik and everything what you can find (there are 2 options already) on the recovery.
vanderax said:
you need to do wipe cache and, wipe data and factory reset. That erasing part is normal. Your phone is not bricked. That android robot portion just verifies the stock recovery and partitions. No problem with it. just wipe cache dalvik and everything what you can find (there are 2 options already) on the recovery.
Click to expand...
Click to collapse
did the factory reset and wiped cache, still nothing. This is totally stressing me out. Any other ideas?
Yesterday i SPT boxed my s6 edge and had the exact error. You may be lost with your eMMC files.. You should repair emmc with jtag...
vanderax said:
Yesterday i SPT boxed my s6 edge and had the exact error. You may be lost with your eMMC files.. You should repair emmc with jtag...
Click to expand...
Click to collapse
how do i do that?
also when i put my phone into recovery mode i get at the bottom of the screen, "dm-verity verification failed.... Need to check DRK first.."
=(
anyone got any other ideas?
Hello, after playing with my z90 (with the original rom that was Z90a40_USR_S118 international, bought in october 2015) I wanted to clean it up and make some updates. So I made my backups etc... Entered the recovery (not the green lenovo one wich is very limited) with hold vol - , I choosed to wipe (the phone was encrypted just to mention) all that I can and reset to factory, all was done but when it finished, it reboot and it stuck to initializing just after lenovo logo it reboot... initializing... and it s an inifinite loop. So I retryed to go to the maintenance recovery but it s not possible a black screen come and it reboot, I can go to the limited lenovo green recovery, but no factory reset, so I make the wipe datas etc... nothing... infinite reboot loop!
So I found some rom put them in the micro SD, go for an update.zip with the recovery, update work well but... initializing.... reboot...
Grrr, lenovo... So I take the big tools, installed a minimal win7 with qualcom drivers, lenovo ones, qpst. I tried many manipulation to enter the download mode with port com (I finaly managed multiple times with not the exact manipulation it s vol- + power + 10s and multiple spanning of the vol - button....) And I have succefully flashed multiple roms with qfil but with always the same results... initializing, reboot... I don t know where to search now, I someone can help me to find where to go, perhaps reflashing the recovery or I saw the .qnc in a russian forum but I can t understand one word.... 2 days of flashing make me hate my lenovo, my first brick with a phone . Any help?
Thanks,
sorry for my bad english
Steph
costeph said:
Hello, after playing with my z90 (with the original rom that was Z90a40_USR_S118 international, bought in october 2015) I wanted to clean it up and make some updates. So I made my backups etc... Entered the recovery (not the green lenovo one wich is very limited) with hold vol - , I choosed to wipe (the phone was encrypted just to mention) all that I can and reset to factory, all was done but when it finished, it reboot and it stuck to initializing just after lenovo logo it reboot... initializing... and it s an inifinite loop. So I retryed to go to the maintenance recovery but it s not possible a black screen come and it reboot, I can go to the limited lenovo green recovery, but no factory reset, so I make the wipe datas etc... nothing... infinite reboot loop!
So I found some rom put them in the micro SD, go for an update.zip with the recovery, update work well but... initializing.... reboot...
Grrr, lenovo... So I take the big tools, installed a minimal win7 with qualcom drivers, lenovo ones, qpst. I tried many manipulation to enter the download mode with port com (I finaly managed multiple times with not the exact manipulation it s vol- + power + 10s and multiple spanning of the vol - button....) And I have succefully flashed multiple roms with qfil but with always the same results... initializing, reboot... I don t know where to search now, I someone can help me to find where to go, perhaps reflashing the recovery or I saw the .qnc in a russian forum but I can t understand one word.... 2 days of flashing make me hate my lenovo, my first brick with a phone . Any help?
Thanks,
sorry for my bad english
Steph
Click to expand...
Click to collapse
Hi,
here is my solution if can help.
I had on my vibe shot s208 rooted ROW. It stacked after SU update in boot loop.
1. I did wipe data without formatting from recovery mode (Vol+ and Vol- and Power button. When Logo is on release power button and hold Vol+ and Vol - until you are in recovery mode). STILL boot loop.
2. I did wipe data with formatting from the same menu. - STILL boot loop.
3. I did factory reset from recovery menu (Vol - and Power after logo is on release Power and hold Vol - until you get recovery mode) - STILL boot loop.
Then I did next:
1. I downloaded and installed QFIL (QPST_2.7.422) - I am not allowed to post links yet.
2. I have connected OTG adapter to phone. Phone was off.
3. then connected OTG to PC. It was some HDD activities but I did not hear any sound.
4. press Vol- for as long as something is going on - HDD activities. Then I think came up sound too - but not sure.
5. I had installed Qualcomm USB drivers from before I suppose.
6. Because I couldn't see my device as ...908 I disconnected and connected again usb cable... then I got my device as ...908 in device manager, but it was written "RECONNECTED" or similar in front of word "QUALCOM".
7. Then just follow instructions for QFIL. and ROM will be installed.
First I have installed INTERNATIONAL no root ROM. But because I needed phone to be rooted in order to use data recovery software I flashed again with s240 ROOTED. When I flashed second time I did not use OTG, just direct usb cable connection to PC, and my phone was again recognized after I reconnected usb cable and in device manger was "RECONNECTED" in front of word "QUALCOM".
Hello, thanks for replying. But I already tried all the roms with qfil, they were successfully installed as wtih miflash but I always got a initializing boot loop... Unfortunately I tried some other method, I successfully erase all partitions, I m now in 9006 mode with a long vibration on start and I cant do anything now No flashing works anymore... I ll try some stuff when I had a little time.
did you find a solution ?? , cause I have the same problem ... tried everything, adb or cwm recovery won't work cause my device is not rooted nor the usb debugging is on .. so am stuck with this "initializing loop".. flashing didn't solve it for me, I tried every ROM I could find, rooted or not .. nothing .... this problem happened with my phone after wiping user data and trying to restore QCN, cause before this problem I had another one with network services, tried to solve it, and here I am, from bad to worse
Hello,
I had the same problem. I tried with QFile and MiFlash but unfortunately without success. will you a track ?
I reinstalled the drivers QDLoader HS- USB Driver. I maintained volume + for 3 seconds , however, nothing happens ! (Before it worked ) I also tried adb reboot eld the prolème is the USBport phone is not known !
I followed the procedure of DejXDA carefully until the end staying press the VOL- the phone starts to recharging battery ... have you others sollutions ? thanks in advance.
Hey there !
Same problem for me... The solution may be to rebuild the partition table, but we need a working phone, and a backup with QPST.
Would anyone post a *.qcn file from his phone, made with QPST Software Download ? or a *.hex ?
And the user partitions ? Or a factory image (*.mbn) ?
Any gurus here, what would you advise for that problem ? Would using QPST properly work ?
Cheers !
Z90-7 (Z90a40) unbricked (at last...)
Hello!
After days and days of fails, my Z90-7 is unbricked!
How?
Just follow the OTG cable method, but copy in the SD card, in the sdfuse folder, this image:
Z90a40_S209_150716_ROW.qsb
You can download it from russian forum*, freely.
*I'm not allowed to post links, but enter the exact reference (Z90a40_S209_150716_ROW.qsb) in Google search (don't accept the Google's proposition to correct it), the link is the first answer. Use Google trad as I did if you don't speak russian .
Hello ,
I have a Lenovo vibe shot Z90-7
I wanted to set an international Rom 5.1 and now since it gets stuck on initializing indefinitely.
I have access to the recovery mode so I spend not to turn off the phone.
I Agency will proceed as this I put out the létélphone I press the volume + and I connect it to the ordidateur to put in download mode, but there is nothing after it launches in initializing .
So I essyer with presses of flight - and connects to the PC and it remains on the Lenovo logo.
In prériphérique manager there wrote lenovo ADB android.
Can not have Qualcomm hs -usb in the Port . even after installing the driver.
you have an idea what I can do?
Thank you
z90-7 not working
Hi,
i tried to install 20150619_VIBEUI_V2.5_1525_5.404.1_ST_Z90-7-Root_Phoenix rom on my lenovo vibe shot using Qfil , After Qfil finished flashing the mobile shutdown and It does not turn on anymore
and computer does not recognize it anymore.
what can I do??
Edit:
Problem solved - phone recovered, and rooted successfully. I think the problem was that I didn't use the most recent version of SuperSU. I was using version 2.46 iirc, but I finally got the root working with version 2.76 (filename UPDATE-SuperSU-v2.76-20160630161323). The TWRP version I used is twrp-3.0.2.0-0-h960a.img. (I used this version of twrp both in the failed root attempt as well as the successful one). After I attempted root with 2.46, the phone just hung at the "your device software can't be checked for corruption". To get my phone back, I booted it and connected to USB (you might have to enter fastboot by holding the down volume button and plugging in the USB cable, keeping the down volume pressed until the phone boots, or you might just boot the phone normally and plug it into the USB cable, even though the phone will "hang" doing this, lgup can detect it and you'll be able to "refurbish" with marshmallow kdz which you should have on your computer. I updated my phone to marshmallow before attempting the root, so I had the kdz already. The one I used is v20a. Anyway, after refurbishing, the phone is recovered and usable again, you still get the "can't check for corruption" screen on boot but it only stays for 5 seconds, and then the phone starts. This is normal for an unlocked bootloader. What I did after recovering the phone was to save SuperSU 2.76 (again, filename is UPDATE-SuperSU-v2.76-20160630161323) onto my phone's SD card. Then I reflashed twrp (boot into fastboot, then from console window "fastboot flash recovery twrp-3.0.2.0-0-h960a.img". Then I had to disconnect from the USB cable, and remove the battery. Apparently some phones will perform a factory reset if you attempt a reboot via the console after installing twrp - this is why I removed the battery - then I put the battery back in and booted into recovery mode. To do this (contrary to most instructions I found online which give the wrong button presses), I held the down volume arrow, and then pressed power until the LG logo showed up. Keeping the down volume pressed, I released only the power button, then tapped the power button until I got to a recovery screen (again, keeping the down volume pressed this whole time). Select "yes" both times and you should be in TWRP. Just follow instructions from there that you can find in rooting guides. When you're ready to restart the phone, you'll get the familiar "can't check for corruption" nag screen, but this will go away after a few seconds - LG logo will briefly appear, then disappear and back to that stupid nag screen. But after a few more seconds, the phone starts up. Confirmed rooted with rootchecker!
Below is my original thread where I describe the problem
So I unlocked bootloader, installed twrp and everything fine so far. I put supersu zip file into download folder, flashed with twrp, cleared cache, and went to system reboot - now the phone just hangs at "your device software can't be checked for corruption"
I should say that instead of pushing the supersu zip to sd card, I just saved it in 'downloads' folder of the phone. I also had to do the trick where I flash twrp, and then remove battery, restart phone to recovery mode, because a reboot of the phone would not allow me to use twrp (it just did factory reset)
I can get back into twrp via recovery boot via down volume + power, and I can get into fastboot via down volume + USB cable, but I can't get anywhere else.
I installed stock recovery image from here: droidviews. com/install-stock-recovery-on-lg-v10-using-fastboot/
Went into recovery boot, the android icon shows up and starts to work, but then goes right back to "your device software can't be checked for corruption"
How can I recover this phone? It's H960A
edit:
Ok, so lgup was not recognizing it, and I couldn't install kdz to recover android. I installed lgbridge, then plugged phone in via fastboot (down arrow + usb). lgup then recognized it, and I refurbished with mm kdz. Seems ok now, but still not rooted, and I still get the "your device software can't be checked for corruption" when I boot up (afaik this is because bootloader is unlocked). Tried to root again, same issue. Except this time lgup would not recognize from fastboot, so I just booted phone normally and connected via USB. Then lgup recognized it and I was able to refurbish again
How can I root this thing? at least I have a working phone again
I'd need some help:
I have a Mediatek phone with TWRP 3.2.3.
I charged my phone using Qualcomm 3.0 fast charger which destroyed the data circuit of my phone.
So the data connection (with the computer, USB stick etc, USB audio with my car) doesn't work.
I tried to reset my phone back to factory settings. But the mistake I made was that I went to the settings of the phone and made a factory reset. The phone booted to TWRP where I tried to restore the backup I had. Restore process went OK and the phone booted - but back to TWRP. It doesn't seem to boot normally at all and I cannot flash it via USB connection. It boots to TWRP each'n'every time.
Is it gone/bricked for good or are there still some ways to get it fixed. Mainboards are not available anymore so if I cannot fix it then it's totally bricked.
Thanks in advance.