Has anyone found a suitable car dock for the dual screen? It seems like most of them don't open wide enough to accommodate both screens (6.5")
Wireless charging would be even better but since the pad would be near the side I don't know if anyone makes something like that
I use this one with a custom bracket to fit my dash.
You can adjust the bottom supports to suit the folded or unfolded size.
I use the LG dongle for charging.
€ 6,36 18%OFF | 360 Universal 7 8 9 10 Inch Car Air Vent Phone Tablet Stand Holder for Iphone In Car Tablet Holder for Car Suitable Ipad Mini
https://a.aliexpress.com/oQGHo2uRZ
I stuck a metal plate on the inside of the DS case and im using a magnetic holder. Works well, but you'll lose the wireless charging capabilities with case on. For me it was worth the compromise.
Magnetic holder on the air vents, get two if you want to put it more secure, I left the metal plates inside the case and not on the phone itself
anyone consider using microsuction tape? haven't tried this yet but it seems like it could work.
I would like to use a QI Car Charger.
Anyone has an idea which one to use for the Dual Screen Mode?
The left grab-arm must be way shorter.
Or does anyone know a QI Charger which grabs the Phone from Top and Bottom?
Ali got it
I ordered this one for the price of 4 $ and 42 cents. that is including shipping from China to Holland LMAO
https://nl.aliexpress.com/item/4000414665875.html?spm=a2g0s.9042311.0.0.3da24c4dPU7FLt
Should be possible to have the phone opened up, do 2 or more things on the phone AND driving at the same time
Seriously! Don't do that!
Caved
Related
Hello everyone I wanted to share my experience with a wireless charging pad and a lifeproof case. I purchased the Nuud lifeproof case a while back and ended up having to replace it due to the charging door that snaps closed started breaking. I figured a way to prevent me from opening that little snap door is to go with wireless charging.
I purchased the wireless charging reciever card and the oem charging pad off amazon. Much to my disappoint me the case was too thick for the wireless charge to continually work. It recognizes that its on the pad but would act as if I were plugging and unplugging a power cord every 2 seconds. So I tried to come up with ways to reduce the surface area between my card and the charger pad. I removed the stickers which ended up not being enough but then came up with the idea to remove the top cover of the oem charging pad. Removing this plastic seems like it was just enough to get it to work correctly. The only problem I see now is the phone is actually sitting on top of the coil which brings up some heat issues.
I'm thinking of sewing together some fabric to act as a cover. What do you guys think about this?
BUMP - I have a very thick ballistics case. I am wondering if a solution like this would work for me as well.
stein5830 said:
BUMP - I have a very thick ballistics case. I am wondering if a solution like this would work for me as well.
Click to expand...
Click to collapse
I doubt my case is as thick as yours stein but it is working correctly once I removed the plastic cover on the charger pad. Not sure if you have all the items yet but you can find them on amazon for probably around 60 bucks.
Wireless Charging is working fine for me with my Otterbox Defender case and an Incipio Ghost 100 Wireless Charging Base. I'm using a cheap China QI antenna receiver that I got on eBay.
Currupt247 said:
Hello everyone I wanted to share my experience with a wireless charging pad and a lifeproof case. I purchased the Nuud lifeproof case a while back and ended up having to replace it due to the charging door that snaps closed started breaking. I figured a way to prevent me from opening that little snap door is to go with wireless charging.
I purchased the wireless charging reciever card and the oem charging pad off amazon. Much to my disappoint me the case was too thick for the wireless charge to continually work. It recognizes that its on the pad but would act as if I were plugging and unplugging a power cord every 2 seconds. So I tried to come up with ways to reduce the surface area between my card and the charger pad. I removed the stickers which ended up not being enough but then came up with the idea to remove the top cover of the oem charging pad. Removing this plastic seems like it was just enough to get it to work correctly. The only problem I see now is the phone is actually sitting on top of the coil which brings up some heat issues.
I'm thinking of sewing together some fabric to act as a cover. What do you guys think about this?
Click to expand...
Click to collapse
Try moving the phone slightly on the charging pad.
I don't have the factory pad but on both of my qui charging pads the phone needs to be placed slightly above center. If I put it directly on the center I experienced the same symptoms you are describing.
Sent from a Galaxy S4... Far far away
gadget! said:
Try moving the phone slightly on the charging pad.
I don't have the factory pad but on both of my qui charging pads the phone needs to be placed slightly above center. If I put it directly on the center I experienced the same symptoms you are describing.
Sent from a Galaxy S4... Far far away
Click to expand...
Click to collapse
im thinking this oem charging pad is the prob I'm going to order the ghost and see if I get better results.
For the last few weeks I have been using my Padfone X quite often. It has become a conversation piece. Most people get stunned when they see a phone that transforms into a tablet. Not too sure why the market is not flooded with devices equal to or similar to this but its a shame that ATT no longer offers this model. I have no regrets for this purchase.
I was put on recently about a huge blowout sale ATT had on the Incipio Folio cases now going for $10 on the ATT store. These folio cases normally ran for $70, and yet most of us cannot conjure purchasing a neoprene cover for such a price that does really nothing to protect the device and the phone other than give it a "more professional look".
The folio case has been going on strong so far, jumping right into it here are the pros and cons:
PROS:
-Comes in various colors to match your preference
-Gives the device a real professional tablet feel
-Folio flap is very tough and will do a good job protecting the station screen
-The included phone folio matches the look of the station folio and gives the phone a sturdy feel
-When the flap is extended it can keep the Padfone station upright at about a 45 degree angle
-It does what it is
CONS:
-It is only one of the two foolio cases available, the ASUS branded case is still going for $60
-Power button is kind of stiff after putting the case on
-Tablet does not detect when the folio flap is closed
-Cannot use the ASUS Padfone Bluetooth keyboard in combination with the Folio case, however can be kept seperate and still work.
-The phone folio case has to be placed on with a special passive adhesive over the original padfone back cover, should you wish to remove it, you'll have to buy another one to place on if you do.
-Orientation is a bit difficult in panorama mode when wanting to keep the station upright, flap does not flip back 180 degrees, only 45 degrees. Its almost like youre forced to keep the padfone upright, despite the cameras placement which is not exactly upright friendly.
I am not gonna complain much because of two factors, its a folio case and I got it for $10 and it was the cheapest licensed folio available. Not too many accessories for the Padfone X, but if youre looking for a cheaper alternative to the ASUS branded folio, this is the way to go
I took a Dremel to mine and got the back cover to work with the keyboard. Obviously, this means the screen cover flap had to go. It's good enough to keep fingerprints off of the station when in laptop mode and still protects it from surface scratches. I went ahead and ordered a second $10 Incipio set to swap the station into in case I feel like leaving the keyboard at home.
Sent from my ASUS PadFone X using XDA Free mobile app
8125Omnimax said:
For the last few weeks I have been using my Padfone X quite often. It has become a conversation piece. Most people get stunned when they see a phone that transforms into a tablet. Not too sure why the market is not flooded with devices equal to or similar to this but its a shame that ATT no longer offers this model. I have no regrets for this purchase.
I was put on recently about a huge blowout sale ATT had on the Incipio Folio cases now going for $10 on the ATT store. These folio cases normally ran for $70, and yet most of us cannot conjure purchasing a neoprene cover for such a price that does really nothing to protect the device and the phone other than give it a "more professional look".
The folio case has been going on strong so far, jumping right into it here are the pros and cons:
PROS:
-Comes in various colors to match your preference
-Gives the device a real professional tablet feel
-Folio flap is very tough and will do a good job protecting the station screen
-The included phone folio matches the look of the station folio and gives the phone a sturdy feel
-When the flap is extended it can keep the Padfone station upright at about a 45 degree angle
-It does what it is
CONS:
-It is only one of the two foolio cases available, the ASUS branded case is still going for $60
-Power button is kind of stiff after putting the case on
-Tablet does not detect when the folio flap is closed
-Cannot use the ASUS Padfone Bluetooth keyboard in combination with the Folio case, however can be kept seperate and still work.
-The phone folio case has to be placed on with a special passive adhesive over the original padfone back cover, should you wish to remove it, you'll have to buy another one to place on if you do.
-Orientation is a bit difficult in panorama mode when wanting to keep the station upright, flap does not flip back 180 degrees, only 45 degrees. Its almost like youre forced to keep the padfone upright, despite the cameras placement which is not exactly upright friendly.
I am not gonna complain much because of two factors, its a folio case and I got it for $10 and it was the cheapest licensed folio available. Not too many accessories for the Padfone X, but if youre looking for a cheaper alternative to the ASUS branded folio, this is the way to go
Click to expand...
Click to collapse
can you show me the photos about this case?
please send to my email [email protected]
thx b4
sorry i have bad english
fhauzi89 said:
can you show me the photos about this case?
please send to my email [email protected]
thx b4
sorry i have bad english
Click to expand...
Click to collapse
There's photos on the AT&T website, quite representative.
Also I don't think the tablet can detect when the folio flap is closed even for the official ASUS case, there's just no sensor (magnetic or proximity) in the tablet body.
I just received mine yesterday, also for $10 shipped. I agree 100% with all the observations.
So, I ended up with the official ASUS PadFone X Folio Bundle and thought I'd do a compare and contrast.
First off, I don't know why I didn't think of it before but it is obvious now that the ASUS Folio for the phone is an add-on (versus a back cover replacement) due to the added cost of adding NFC and PMA antennas/receivers, which are attached to the inside of the back cover.
Continuing on with the phone folio, the ASUS Folio replaces the original back cover. Interestingly enough, it must be specific to the PadFone X because it retains the AT&T logo. The front flap has an ASUS logo and a cutout for the earpiece, so that a phone call can continue with the cover closed.
In regards to the PadFone X Station folio, the ASUS Folio has cutouts on the front flap for the front-facing speakers. In addition, the sides are fully covered where the Incipio leaves the sides exposed. The ASUS folio covers the volume and power buttons but does not require any additional pressure, unlike the Incipio cover. On the back, the ASUS Folio also protrudes a little because it covers the bottom of the dock where the phone connects, while the ASUS leaves that exposed. This makes the Incipio a little more sturdy when you fold the front flap back all the way to act as a stand. Finally, the ASUS Folio's front flap has three sections, while the Incipio is just one sturdy piece.
The last difference is the primary reason why I am sticking to the original ASUS Folios.
Does anyone know if the wireless qi charging works with the incipio phone back cover? Thx
teioh3 said:
Does anyone know if the wireless qi charging works with the incipio phone back cover? Thx
Click to expand...
Click to collapse
Unless the cover is metallic, it will work. Metal will disrupt the charging capabilities and can sometimes hurt wireless chargers. Pretty sure this is not a metal case.
EDIT:
Now I understand your question - the incipio brand is a replacement back cover too - which means it probably doesn't have the metal leads or powermat receiver built-in.
TigerC10 said:
Unless the cover is metallic, it will work. Metal will disrupt the charging capabilities and can sometimes hurt wireless chargers. Pretty sure this is not a metal case.
EDIT:
Now I understand your question - the incipio brand is a replacement back cover too - which means it probably doesn't have the metal leads or powermat receiver built-in.
Click to expand...
Click to collapse
It's not a replacement, just an additional stick-on. Should work. Only worry is the increased distance from the charger.
I just tested the official wireless charger's distance, and it works while about half an inch away - I guess as long as the wireless pad you're using is a Powermat standard then it should be NO PROBLEM. I didn't test to see the limit of the wireless charger, but I know that the Qi standard is less powerful. Powermat devices like the Asus Padfone X/S can still charge with Qi but it's been my experience that Qi chargers only work about 1/4th of an inch away or less - and they charge much more slowly.
Just don't get metal in between the charging pad and the phone and you're okay.
Looking for a good car mount with wireless charging that will work with the nexus 6 any recommendations?
I'd recommend not using one. Wireless charging will be way to slow on the n6.
jdenman03 said:
I'd recommend not using one. Wireless charging will be way to slow on the n6.
Click to expand...
Click to collapse
used the square stock wireless charger with my n5, stuck a clip to the back of it and just relied on the magnets to hold it. Didn't wiggle at all, never fell off, was perfect, wish I could rig the same thing with the N6, but I don't think the magnets will be near strong enough.
A qi charge is going to charge at 1a at most, for he N5 that was more than enough to cover full brightness, gps, and streaming over bluetooth, and still providing enough to charge the battery. I IMAGINE if you could somehow hook it up like that, it would provide enough of a charge to the N6 as well, at worst I think you'd not lose charge. JMHO though.
So if you not recommending the wireless charge on it then do the sell a fast charge adapter for the car? Really the main thing is a good car dock. I figured the wireless charge would just be a plus.
I've been using the Airdock with my Nexus 5 for a while now and I absolute LOVE it. It uses magnets to hold the N5 in place, and I'm hoping the N6 also has these magnets. It also has a special surface that is supposed to hold certain phones without magnets, depending on the material of the back of the phone.
Also as far as the speed of charging, it works well enough to slowly charge my N5 with the screen always on in my car and with GPS running (at a minimum, it keeps it from losing charge). This is all I need in my car. On those certain occasions where you really want a faster charge, I just plug it in.
Let us know if it works with N6. Can you have a slim case on the phone an the magnet still works?
Got my N6 today. Unfortunately it doesn't work with the AirDock, as it doesn't stay on it. Looks like the N6 doesn't have any magnets. Very disappointing.
nyijedi said:
Got my N6 today. Unfortunately it doesn't work with the AirDock, as it doesn't stay on it. Looks like the N6 doesn't have any magnets. Very disappointing.
Click to expand...
Click to collapse
I've read the magnets are near the bottom of the phone. Can you double check?
fictionoid said:
I've read the magnets are near the bottom of the phone. Can you double check?
Click to expand...
Click to collapse
I just ran a magnet all over the back of the N6. There is indeed some type of magnetic pull in the bottom corner, however, it is EXTREMELY weak. I'm guessing it's there to maybe help nudge the phone into the correct position when laying flat on a (future official?) qi charger, but it is absolutely not enough to hold it onto the AirDock. By way of comparison, the magnetic pull with the magnet is much stronger, and over a much greater area, on the N5.
Also, the N6 is a lot heavier than the N5. Add the curved back into the equation, and these 3 factors pretty much guarantee the phone won't work with the AirDock. Believe me, I tried to get it to stick on the AirDock today, and there's no way it's happening.
iOttie Qi charger works. You've got to find the sweet spot to have it grasp the side, without hitting the volume buttons, and still getting the charging coils aligned. Not super difficult - just takes a second to align. I expect this to be irrelevant once I get a case which keeps the buttons recessed.
-bZj
Anyone who's using a QI car dock have any input on charging / maintaining charge with screen always on, brightness up, streaming music, maps, etc.
I'm just curious if the iOttie or any other wireless chargers can avoid LOSING charge with the N6 when under "heavy" use.
One problem I find is you can't keep the screen on when wirelessly charging once the battery is at 100%. The phone stops charging so the screen goes off. Very annoying hopefully someone can find a fix.
MoeDaddy said:
One problem I find is you can't keep the screen on when wirelessly charging once the battery is at 100%. The phone stops charging so the screen goes off. Very annoying hopefully someone can find a fix.
Click to expand...
Click to collapse
The "Stay Awake" option in the Developer Options should be what you're looking for.
No that doesn't work when the phone is fully charged because the N6 doesn't have trickle mode it actually shuts off charging. Thus the screen shuts off.
My Homebrew Wireless Car Charging Solution
I made my own wireless car charger by grafting a PowerBot charging puck onto a Ram Large X-Grip. I simply used double-faced tape to attach the PowerBot to the X-Grip. I started this with my Nexus 5 in a Spigen Neo-Hybrid case and it works just as well with my N6 inside a Diztronic Slim TPU case.
Here's the charger:
http://www.amazon.com/PowerBot®-PB1...687&sr=8-1&keywords=powerbot+wireless+charger
And here's the X-Grip:
http://www.amazon.com/Ram-Mount-Uni...TF8&qid=1416714725&sr=8-4&keywords=ram+x-grip
You'll need a way to attach the X-Grip to your vehicle. Ram-Mount's website has countless ways to do this.
Here's Ram's website:
http://www.rammount.com/
I used a Mirror-Mate(TM):
http://www.rammount.com/NewProducts/MirrorMount/tabid/2538/Default.aspx
And paired it with a Long Arm (don't use the shorter ones; the phone will hit the rear-view mirror in portrait orientation):
http://www.rammount.com/CatalogResu...65077045066045050048049085045067/Default.aspx
I can leave the PowerBot plugged into my cigarette lighter all the time (standard mini-USB cable and 12V-USB adapter) and it's easy to mount or remove the phone, just squeeze the arms of the X-Grip together and out it comes (this takes two hands or the phone will fall). This works great for calls, navigation, or as a dash-cam. Ram makes suction cups for those who want to mount directly to the windshield but I highly recommend the Mirror-Mate(TM).
Not cheap, total cost about $70 plus shipping.
EDIT: I just saw this in another thread and I'm going to replace my PowerBot with this Anker:
http://www.amazon.com/Anker-Ultra-S...Qi-Enabled/dp/B00HIZ3ZI4/ref=cm_cd_ql_qh_dp_t
Right now the 4 rubber grippers are flush with the front of the phone, which makes it a bit finicky to mount securely. The Anker charging pad is about 1/8" thinner than the PowerBot, which will accommodate the thickness of the phone perfectly with about 1/8" of overlap between the 4 grippers and the bezel of the N6. Putting the N6 in the X-Grip without the charger in-between leaves the 4 grippers protruding above the bezel about 3/8" which means they can get in the way if I'm trying to use the touchscreen near them.
See my posts in this thread...
http://forum.xda-developers.com/showthread.php?t=2910978
[Q] Car mount similar to iOttie?
Sent from my Nexus 6 using Tapatalk
toyfreak said:
I made my own wireless car charger by grafting a PowerBot charging puck onto a Ram Large X-Grip. I simply used double-faced tape to attach the PowerBot to the X-Grip. I started this with my Nexus 5 in a Spigen Neo-Hybrid case and it works just as well with my N6 inside a Diztronic Slim TPU case.
Here's the charger:
http://www.amazon.com/PowerBot®-PB1...687&sr=8-1&keywords=powerbot+wireless+charger
And here's the X-Grip:
http://www.amazon.com/Ram-Mount-Uni...TF8&qid=1416714725&sr=8-4&keywords=ram+x-grip
You'll need a way to attach the X-Grip to your vehicle. Ram-Mount's website has countless ways to do this.
Here's Ram's website:
http://www.rammount.com/
I used a Mirror-Mate(TM):
http://www.rammount.com/NewProducts/MirrorMount/tabid/2538/Default.aspx
And paired it with a Long Arm (don't use the shorter ones; the phone will hit the rear-view mirror in portrait orientation):
http://www.rammount.com/CatalogResu...65077045066045050048049085045067/Default.aspx
I can leave the PowerBot plugged into my cigarette lighter all the time (standard mini-USB cable and 12V-USB adapter) and it's easy to mount or remove the phone, just squeeze the arms of the X-Grip together and out it comes (this takes two hands or the phone will fall). This works great for calls, navigation, or as a dash-cam. Ram makes suction cups for those who want to mount directly to the windshield but I highly recommend the Mirror-Mate(TM).
Not cheap, total cost about $70 plus shipping.
EDIT: I just saw this in another thread and I'm going to replace my PowerBot with this Anker:
http://www.amazon.com/Anker-Ultra-S...Qi-Enabled/dp/B00HIZ3ZI4/ref=cm_cd_ql_qh_dp_t
Right now the 4 rubber grippers are flush with the front of the phone, which makes it a bit finicky to mount securely. The Anker charging pad is about 1/8" thinner than the PowerBot, which will accommodate the thickness of the phone perfectly with about 1/8" of overlap between the 4 grippers and the bezel of the N6. Putting the N6 in the X-Grip without the charger in-between leaves the 4 grippers protruding above the bezel about 3/8" which means they can get in the way if I'm trying to use the touchscreen near them.
Click to expand...
Click to collapse
Did you use super glue or something to attach the Qi charger to the Xgrip?
Also, how long is the USB cable provided by Anker?
picked this up on sale for my nexus 6 w/ spigen ultra hybrid
https://slickdeals.net/f/7565384-au...s-smartphone-charger-qi-for-9-99-frys-com?v=1
nexus 6 is a bit wide for it, but the handles flex enough to let it go in; wireless charging, went up 1% from ride home from frys with gps navigation on w/ screen halfway
Momotani-Hitoshi said:
Did you use super glue or something to attach the Qi charger to the Xgrip?
Also, how long is the USB cable provided by Anker?
Click to expand...
Click to collapse
I used double-faced mounting tape between the X-Grip and charger. The cable is 1m long.
What did you use to bond the qi charger to the ram mount?
I wanted wireless charging, but the only one available (from fonesalesman.com) costs about $80USD to my door.
So, I bought an S5 pad and used some copper tape I had lying around. NOTE: Copper tape (or at least the one I have) is only conductive on one side because of the adhesive. I rolled the ends up to make large contacts for the terminals on the phone and wireless charging pad.
I also removed the golden pins from the wireless charging pad because they were a bit thick. If you do this, be careful not to remove the silver pad underneath (I almost did).
See pictures attached, they're pretty explanatory.
The current pad I am using is a bit thick, and have ordered a new one, but it works! And it doesn't cost the earth.
Hope this helps people.
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
How does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
killbom said:
how does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
Click to expand...
Click to collapse
hi res picture 3mb
Thumb:
Hey guys,
It doesn't look as good as the post from DimonVideo, but as I said, I'm waiting on a thinner wireless model.
I'll put some pictures up later when I get home.
0.5mm Receiver
novastorm17 said:
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
Click to expand...
Click to collapse
I'm planning on getting this one.
Can't post the link to amazon as I do not have the minimum posts to do so.
Search this:
Alpha SlimPWRcard - 0.5mm Qi Receiver for Samsung Galaxy Alpha with integrated NFC coil
Those are the only model available for the Alpha. But since I don't live in USA, it would cost at least $50USD for me. So, I put together this thing
Where you get the pinout of the alpha wireless charger?
Hey guys!
Thought I would post a review for this Qi wireless car charger since I didn't see much info about it and help those in deciding one for their car.
I have been using this Qi wireless car charger for about 4 months. The weather here is summer now so the car interior does get super hot, and so far this charger has been working like a champ in the heat.
The charger comes with a bunch of accessories which include:
-Vent adapter holder
-Traditional suction cup stand holder for dashboards
-Micro Usb cable
-Usb car chager (1 input)
-Sticky pads for wire management
I used the suction cup on my dash since my vents in my car are not ideal for my setup. The Qi charger is made hard sturdy black plastic and the section where you place your phone is made of a softer grippy rubber that holds the Nexus 6 very well. There is button on the back that release the two arm clamps. The Nexus 6 being a big of a device I thought it would be a tight fit, but I am happy to report that there is plenty of space. I have a Caseology Case and still a bit of extra room on the dock. So for those with thicker cases than mine can still fit, but in terms of it charging through a thicker case is something I do not have to test, but for those familiar with my case which I will put a link on the bottom of this post, my phone charges perfectly fine with it. Also the Qi charging unit in this has a 3 coil system so placement is not an issue and wireless charging is maximized and efficient as possible. There is a LED light on the bottom that indicates if it idle or charging, Green means idle and Blue means charging. The cradle of the charger is very sturdy and holds the Nexus with ease, have not had it drop my phone (yet) and hopefully stays that way. I use the charger everyday for the past 4 months and yet to encounter an issue, remember I am using it 95 degree weather for the past 4 months and it has not died on me yet. Once winter comes I will update on how it handles the cold, hopefully like a champ as it does in the summer! I attached some pictures for everyone to have a better look at it. Overall I am very happy with this charger and highly recommended!
Any questions about this product let me know and I will try my best to answer and help!
Amazon Links:
Qi wireless charger:
http://www.amazon.com/RAVPower-Wire...id=1440909770&sr=8-1&keywords=ravpower+qi+car
Case:
http://www.amazon.com/Caseology®-Me...=1440911291&sr=8-1&keywords=nexus+6+caseology
Thanks!
Look.like so good.
Can you try in front window and let us know how it works? When I get my phone it's going to be a window mount and since I'll have to use an OTG adapter for long distance that means I'll have to use wireless charging.
thunderstruck! said:
Can you try in front window and let us know how it works? When I get my phone it's going to be a window mount and since I'll have to use an OTG adapter for long distance that means I'll have to use wireless charging.
Click to expand...
Click to collapse
If you mean having the suction cup on the windows then yes it works even better cause the surface on the glass gives it an even better grip.