Hey friends! :fingers-crossed:
I have lenovo a3500hv tablet. I tried to install a custom rom with twrp, but it failed. After the process of flashing I just checked the recovery menu and it was working. I turned off the device and after few hours, I tried a lot to turn it on, but I failed (There is no screen light, no vibrate or any sign). So, Searched a lot and I found that I should flash the original rom to survive my tablet. When I try to connect tablet to PC, my PC makes sound and I can see my device name in the Device Manager; Also, I have the MTK drivers installed. So, I load the scatter file and try to flash with SP Flash Tool and it's shows me the name of my tablet, but when I start to flash, SP Flash Tool does not start the flash process. I used a lot ways to connect my tablet like Volume Down + Power, Volume Up Power and ...
Please help me guys
Related
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Try to hard reset. Hold down the power button for at least 30 seconds. On devices that support it, the screen will turn off and the device should begin to cold reboot. A cold boot is where a device starts up from a power-off state. If that doesn't work you might have to test just how "nonremovable" their battery is and disassemble your device. If there aren't wires coming from the battery that are soldered to the phone's circuit board then it should be removable.
Hello to everyone,
I have the same GO phone. Do not try to open it (with purpose to take off the battery). To connect that phone in preloader mode just press volume up and then connect it in your pc. If you have the correct usb drivers, SP flash will find your phone.
I have done it and it worked for me. I have rooted my GO N1-y and I have used SP flash to unbrick my phone (I faced a problem with SP flash v.5.1352.01 and as a result I bricked my phone) using the official ROM. I did it with SP flash v.3.1320.0.174.
So, please give any feedback in case you find a custom rom for N1-Y.
Be good!!
thanasisvas said:
Hello to everyone,
I have the same GO phone. Do not try to open it (with purpose to take off the battery). To connect that phone in preloader mode just press volume up and then connect it in your pc. If you have the correct usb drivers, SP flash will find your phone.
I have done it and it worked for me. I have rooted my GO N1-y and I have used SP flash to unbrick my phone (I faced a problem with SP flash v.5.1352.01 and as a result I bricked my phone) using the official ROM. I did it with SP flash v.3.1320.0.174.
So, please give any feedback in case you find a custom rom for N1-Y.
Be good!!
Click to expand...
Click to collapse
I'm on my phone but I have another thread where I've discussed my many rom uses on the N1-Y
I've just found what I think is the best rom.
It's actually made for the Xolo Q1000s (the q1000s plus is pretty much a rebranded go n1y)
http://www.xolo.in/xolocare/software-update?page=3
If your try to Flash it via cwm it'll give an error.
I used 7 zip to view the archive and I edited it so that it never checked build.prop.
Flashed fine and is working great.
martistmusic said:
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Click to expand...
Click to collapse
Im not sure about your device, but i believe if your battery is not removeable, there will be a way to turn off your phone.
try pressing volume up and power until it vibrates 3 times, if its sony then this will work, try other button combination too
Try this : press volume up + volume down + Power
it work
MrMaddTraxx said:
Try this : press volume up + volume down + Power
Click to expand...
Click to collapse
I have mtk a device with a non-removable battery and I tried SEVERAL thing nothing works the dvice wase break dead then i tray these
prese up volume + down volum + power buttons and hold down and
i clique download in spflash tool
HaniAnis said:
I have mtk a device with a non-removable battery and I tried SEVERAL thing nothing works the dvice wase break dead then i tray these
prese up volume + down volum + power buttons and hold down and
i clique download in spflash tool
Click to expand...
Click to collapse
Well if you read the previous reply you should've noticed it was that combination to turn the device off.
I don't know what kind of problem you have so I have no idea how I could help you unless you say so
martistmusic said:
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Click to expand...
Click to collapse
Listen
your phone is rebooting but not showing on the screen
so what you need to do is
just try various combination like
vol up and vol down
vol up and power
vol down and power
and try this combination and keep pressing the button
and connect device to pc
and you will get the error that device power up too early
and the reason for the error is
reboot of device but no display on screen
so just try and try until your pc detect device and flashing starts
and believe me this the correct method
because i have repaired my phone with same method and i am sure because it worked for me three times
so keep trying the combination and at a moment your flashing tool
will start the flashing?
:fingers-crossed::fingers-crossed:
Give a LIKE :good::good:
martistmusic said:
Hi, I ave a MTK 6589 device (Green Orange N1-Y) and I would like to flash custom rom I've downloaded from Needrom with SP Flash Tools.
The problem is that this phone is with built-in battery. How to flash the rom? SP Flash Tool give me error " brom error s brom cmd startcmd fail 2005 "
I search all day for a solution, but nothing. Is there any chance?
Thanks
Martin
Click to expand...
Click to collapse
Hope my solution will help
i have an old phone hesens HE-F4 i insert sim card (GSM) and it displays no UIM card currently all the relevant apps of messaging internet and calls cannot be accessed how do i make it work
Initially I tried to root the P9000 following this guide (http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042), and it seems to have bricked my phone. I got this error, (BROM ERROR-1073676724), and now my phone won't boot, or boot into recovery mode. The PC only sees it if I plug it in and press the recovery buttons (Vol+ and power), and then it'll flash up for a short time before vanishing. I've found the only way to keep it visible in the device manager is to use the flashtool to attempt to flash something to it, but I get this error (BROM ERROR -1073414139). I've tried this on a Windows 10 and a Windows 7 PC with no dice on either. Any help would be much appreciated.
holygoatofsteel said:
Initially I tried to root the P9000 following this guide (http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042), and it seems to have bricked my phone. I got this error, (BROM ERROR-1073676724), and now my phone won't boot, or boot into recovery mode. The PC only sees it if I plug it in and press the recovery buttons (Vol+ and power), and then it'll flash up for a short time before vanishing. I've found the only way to keep it visible in the device manager is to use the flashtool to attempt to flash something to it, but I get this error (BROM ERROR -1073414139). I've tried this on a Windows 10 and a Windows 7 PC with no dice on either. Any help would be much appreciated.
Click to expand...
Click to collapse
Fixed it, but I'll leave this up for anyone thinking they might have the same problem. I fixed this by flashing the stock ROM again, but with one key difference. Ensure you install all appropriate drivers, and then when you hit download, plug the phone in and attempt to put it into recovery mode. This will open the port just long enough for the flash tool to keep it open, and it will flash as usual.
Hello!
I have a bricked phone. When I got him, he was in a state "loaded to the screensaver and stop".
I decided to flash him using recovery (carliv touch recovery 2.2). Thanks to recovery I copied all the files from phone. But all my attempts of flashing were unsuccesful - I've got the errors while recovery did an unzipping.
That because I decided to use SP FlashTool. But I've forever got the same error 5069.
I notice, that I can format my phone and download the preloader. But it's all what I can.
What I tried (what i remember):
to load without and with battery;
to put a battery after beginning of flashing;
to flash with pushed power, volume control buttons - all together and alone
to use another system, cable and computer (2 cables and computers, windows and ubuntu);
to flash different versions (from off site);
to use different versions of sp flashtool
Also I found a video, where propose to do the backup of working phone (prestigio 3400) by MTK droid tool and try to flash this.
I would be very grateful if you help me. Thanks
Hello!
My phone, Acer Liquid Z630s, recently had a problem and ended up shutting off as soon as it boots up. I turn it on, the Acer powered by Android white screen shows up then immediately shuts off. What was the problem here?
I couldn't access recovery mode either because it would also show up the same thing above then shut off immediately before it can even reach the recovery mode menu. But I could plug it in directly into download mode through SP Flash Tools because the phone vibrates when I hold down the volume up + power buttons (aka the recovery mode combination which was I think also the download mode combination). I downloaded the correct stock ROM off the Acer website (MT6753) and flashed it. The ROM was successfully flashed. But when I turned it on the screen lit up but it was just a blank black screen. It was lit up, but it was just dark black. I tried to wipe the system and flash the ROM again and at the end of the process, an error message appeared and I looked up the error code and this was exactly it:
"Error 6104
Message: BROM ERROR: S_SECURITY_SECURE_USB_DL_DA_RETURN_INVALID_TYPE (6104), MSP ERROR CODE : 0X00
Meaning: Wrong flash settings or firmware
Solution:
Ensure you set the correct Download-Agent in SP flash tool and are using a firmware for your exact model
Go to Options > Option > Connection > USB Speed > Full Speed
Go to Options > Option > Download > Untick DA DL All with Checksum"
I did what the solution told me, and as I tried to flash the ROM again, but I couldn't turn on my phone anymore. The volume up + power button combination no longer produces a vibration, and when I plug it into my computer it gets detected as a MediaTek USB Port (COM6) but SP Flash Tools no longer detects my phone and gives off this error:
"Error 0x13BE
Message: S_DL_GET_DRAM_SETTING_FAIL (0x13BE)
Meaning: The firmware you're trying to flash is either not compatible with your device or you have selected the wrong flashing settings
Solution:
Ensure that the file(s) you're trying to flash are actually for your exact phone model
Ensure you tick the boxes for only the files present in the ROM you're about to flash"
I don't know what to do at this point. Is it beyond salvation? But my phone still gets detected by my computer and it still produces the sound when you connect a device through the USB ports. Help me please.
Thank you in advance.
Hi , flash this firmware and in Sp Flash Tool set to Download only !!! When you Do Format + Download you lose your imei !
https://drive.google.com/uc?id=12CdmQaP8wi52RZO4jvjSikTWi2l4I1ZN&export=download
Teddy Lo said:
Hi , flash this firmware and in Sp Flash Tool set to Download only !!! When you Do Format + Download you lose your imei !
https://drive.google.com/uc?id=12CdmQaP8wi52RZO4jvjSikTWi2l4I1ZN&export=download
Click to expand...
Click to collapse
Hi there Teddy. Maybe you could help me. I was actually trying to make use of the same thing. SPFT. i flashed the stock rom. i tried rebooting it. seems that it has been bricked. I am using Starmobile Up Prime.
lexpizarro said:
Hi there Teddy. Maybe you could help me. I was actually trying to make use of the same thing. SPFT. i flashed the stock rom. i tried rebooting it. seems that it has been bricked. I am using Starmobile Up Prime.
Click to expand...
Click to collapse
Hi, If you flashed right stock firmware for your device correctly, your device it should not be bricked so I thing your flash file are not good.
Explain me what did you tried and which file you flashed?
Hello all good souls over here.
Could you please help me out with flashing back the original stock ROM to Mediatek MT6737M phone?
UMAX VisionBook P50 LTE, Mediatek MT6737M, 2GB RAM, 16GB internal memory.
What happened:
Before I was trying Oukitel P5 Pro ROM as well as Lineage OS and flashing with SP Flash Tool was working just perfectly.
But then I tried to flash Oukitel P5 Pro Andorid 7 stock ROM. (Oukitel P5 Pro and UMAX VisionBook P50 LTE are completely the same phones. Just different branding)
(And from now on I am not sure if I remember correctly)
When I loaded in scatter file, SP Flash Tool said something about something .... and recommended to do "Format all + Download" and I have done so.
Clicked on the Download button, flashing started instntly when I connected the phone while holding Volume - button.
Flashing stopped in maybe one second with the error which I do not remember as I closed the error window way too quickly. :-(
Later on I noticed that the preloader file is different in this Android 7 ROM then Android 6 ROM.
What is the current behavior:
When the phone is connected (with the battery inside) to the computer phone keeps connecting and disconnecting (appearing in Device manager as Mediatek USB Port) if I click Download button it starts doing "something" instantly which stops at Download DA 100% and after the while ERROR: S_FT_ENABLE_DRAM_FAIL (4032) pop up windows shows up.
The same error happens if I try to Format it and all other combinations in Download tab (Firmware upgrade, Format All + Download)
If I plug in the phone to the computer while pressing Volume - button phone will show up in the Device manager after about 20 seconds.
(Just to note - When the phone was working OK, I started flashing instantly when I plug the phone into the computer while pressing the Volume - button
So that kind of leads me that if nothing will show up in Device manager when I plug the phone to the computer while pressing Volume - button, then there might be the issue with the phone not switching into META mode? Not sure, just what I have read. But I cannot move any forward at this point.)
What I have tried:
- Correct stock ROM and Oukitel stock ROM (both Android 6 and both I was able to flash correctly and was able to boot them, until I tried Android 7 ROM)
- various SP Flash Tools 5.xxxx (and 3.xxxx too, but version 3 does not accept scatter file at all)
- USBDeview and removing all related USB devices from Windows and re-install them back again.
- Various VCOM drivers I have found on the Internet
- Flashing with SP Flash Tools on Linux (ends up with the exact same result - 4032)
- I tried shorting test point to ground on the phone main board. (The result was the same like when I plug the phone in while holding the Volume - button - Phone would not show up in Device manager for about 20 seconds)
- Tried flashing with the battery inside and outside the phone. (When the battery is outside flashing would not start, but the error about incorrect chip type will show up)
- Read many articles about this error all over the Internet
Do any of you think there is a change to bring the phone back to live? Or do you know what actually might happen to the phone? It does not seems to be completele bricked, but I cannot say in what state the phone is.
Thank you very much for your help and have a nice day.
Hi. I need this rom for this phone. I have umax p50 lte too . Please give me link if you can. Thx
@oukitel654
Look inside here:
Common SP Flash Tools error and Solutions - ROM-Provider
Common SP Flash Tools error and Solutions: Hello guys if you are facing a SP Flash tools error code issue then this page is for you where we share solutions for for almost all SP Flash tools error. Common SP Flash Tools error Code: Error 5054, 4032, 8038, 5069, 4001, 4008, 3149, 3168, 2004, 1013, …
romprovider.com