Related
Thanks to our friends in Indonesia, we have the updated 2.2.2 Rom --> odienas and tri_zet
This update has been confirmed to work with:
S7-103, Indonesian version with dual cameras internal/external sdcard
S7-104, US BestBuy/RadioShack version with dual cameras and internal/external sdcard
S7-105, Australian version with dual cameras and external sdcard
Partially working:
S7-101, Austria Mobilkom version - loses camera, GPS?
S7-103, New Zealand - loses GPS?
More Info go ---> http://www.androidtablets.net/forum...d-2-2-2-dual-camera-s7-s7v100r001c98b021.html
Download
http://www.megaupload.com/?d=PVWGU020
http://www.mediafire.com/?9l52jhbl7b09czp
MD5 checksum for updata.app : 74D031FD717D8BF68956EF3F044C8EEB
Update install process:
1. unrar the file, and copy the 'dload' folder to the root directory of a sufficiently large external SDcard formatted to FAT/FAT32 (readable by the S7)
2. turn off the unit, and ensure that you are either plugged in with a battery inside the unit, or that you have enough charge left in your battery
3. turn on, and a progress bar will appear in the middle of the screen. Wait until "OK" is displayed on the screen.
4. turn off the unit by removing the battery and any powerplugs to the S7
5. repeat steps 2,3,4 again. otherwise it will hang at boot screen (instructed by Huawei)
6. Remove the SD card and start the device. If you wish the use the card for the device, remove the firmware files from the SD card before reinserting it.
If the update fails to install, check that your file was properly moved into the SDcard by comparing the MD5 checksum.
The overall process should take less than 15 minutes to complete.
Adobe Flash is not pre install ---> http://www.mediafire.com/?io9d5tkt6mu0k74
To ROOT use SOC ---> http://www.androidtablets.net/forum...ot-official-huawei-s7-android-2-2-builds.html
Thanks!! good job
what's new?
Any idea if this will work with the Telstra T-Touch Tab (Australia)? I'm told on other threads it's identical to the Ideos S7 except without any memorycard soldered onto the board. - and it seems possibly this only has agps too.
What is the latest available offical firmware? Im using S7 bought from Orange PL and mine ver is S7v100R001C98B022-is this the newest one?
Which do you think is the best out of your own experience?
aurionix said:
Any idea if this will work with the Telstra T-Touch Tab (Australia)? I'm told on other threads it's identical to the Ideos S7 except without any memorycard soldered onto the board. - and it seems possibly this only has agps too.
Click to expand...
Click to collapse
It runs just fine on the T Touch mate
hi, Everyone knows if this rom works with the s7-106?
Hi.
I've tried many things and also searched already on the net about this Bluetimes model but I didn't find nothing explain how it could be rooted. I sent a email to manufacturer about this issue but no answer. I only received of manufacturer the explanation how to restore the original firmware.
I tried some apps like...
- Framaroot
- Towelroot 3
- RomasterSu
... but nothing worked.
I tried too a version ROOT of Matricom Midnight G-BOX MX2 v1.1.5 on page http://forum.xda-developers.com/showpost.php?p=45502307&postcount=12 but nothing.
Below is some informations about the Bluetimes 3584F and the link to download the original firmaware given by the Shenzhen Blue times Technology Co., Ltd.
GENERAL:
MANUFACTURER
MBX
MODEL
MBX reference board (g18ref)
HARDWARE INFORMATION:
BOARD
g18ref
HARDWARE
amlogic
CPU_ABI
armeabi-v7a
CPU_ABI2
armeabi
ADVANCED CPU INFO
abi: armeabi-v7a
Processor: ARMv7 Processor rev 0 (v7l)
SOFTWARE INFORMATION:
ANDROID VERSION NAME
JELLY_BEAN_MR1
ANDROID VERSION CODE
4.2.2
API LEVEL
17
ID
JDQ39
BUILD NUMBER
JDQ39.20131220
LINK TO DOWNLOAD:
firmware_Bluetimes_3584F.zip
UPGRADING GUIDE:
1. Unzip the downloaded firmware file, you will get 4 files named "g18ref-ota-XXXX.zip", "factory_update_param.aml", "u-boot.bin" and "recovery.img"
2. Copy the 4 files to the root directory of your SD card
3. Take off the power adapter from your media player and insert SD card to the card reader slot.
4. Press and hold the reset hole on the back of the media player(beside the power socket), then connect power adapter to this item, still holding the reset hole
5. When you see the upgrading process bar showed on your TV screen, you can release the reset hole
After firmware updating finished, TV box will reboot automatically.
I am needing move the apps to SD CARD because the internal memory is almost full but I can do that only if it is rooted.
I appreciate any help.
Someone to help me with this issue?
How can I do myself the "root" ? What are the files I have to edit and what I have to change on the files?
Here's topic you need - http://forum.xda-developers.com/showthread.php?t=2146226
Download utoo-root-signed.zip and flash it as firmware. Just put that one file on root of your sdcard and boot your device in recovery mode (step 4 of upgrading guide you mentioned) and navigate trough menu to flash it. I did not try it myself, but I checked zip file, it should work for amlost all Amlogic MX devices.
Thank you very much, stane1983.
I will do the procedure and after I will post the result.
The newbies, like me, need someone to show the way of the stones.
Got it, finally!!
I will explain to help other users that have the same Blutimes 3584F model:
1- Download the utoo-root-signed.zip file on page http://forum.xda-developers.com/showthread.php?t=2146226 and move it to SD card.
2- Donwload the firmware_Bluetimes_3584F.zip file on the first post, unzip it and move the files quoted below to SD card:
- factory_update_param.aml
- u-boot.bin
- recovery.img
3- Rename the utoo-root-signed.zip inside of SD card to g18ref-ota-20131220.zip
4- Do the steps 3, 4 and 5 of the "UPGRADING GUIDE" on first post.
P.S.: Even with the phone rooted I needed create a 2nd partition EXT4 on SD card to move the apps to it by Link2SD app.
Thank you very much to stane1983.
I have an android car head unit with Allwinner T3.
I asked from the seller the OS files to update my unit because I was experiencing some issues. I received these two files
os_update_YMHC0101-N39-2.3.4.3.12_20180601_152348.zip
YMHC0101-N39-2.3.4.3.12_20180601_152348.img
I used the second file with PhonixCard to create a sd card and update my unit.
The update was successful and my unit information in About Device menu are:
Android version: 7.1.1
Hardware Information: Quad Core AllWinner
Kernel Version: Linux 3.10.65
OS Version: BSP 2.3.4.2.12 - IVT - 180601
MCU Version: 20180426-1-KC1-18
I want to install an app called VocalizerEx. The default TTS engine in my head unit is PicoTTS. I installed VocalizerEx and selected in settings but it's not activated. If I exit the menu and reenter I see that PicoTTS is the activated engine. I think that PicoTTS gets selected as the default TTS engine because it has been installed as a system app. I could convert VocalizerEx to system app if the head unit was rooted but I couldn't find any information to root my unit.
Since I have the above .zip and .img files I was wondering if there is a way to edit them and create a custom update file with VocalizerEx installed as a system app. If it's possible to edit these files I would like to change the boot animation as well.
I explore my head unit file structure and I see that it has the same file structure with the .zip file I have. Could I use this .zip to create the .img update file or just unpack and repack the .img?
I tried DragonFace but I got an error.
How could I edit this .img file? What tools do I need? (I could work on Windows/Linux/Mac OS X.)
Is it safe to unpack and repack the .img? Could a corrupted .img file brick my device?
Hey,
I have an Android Allwinner T3 device and I have problems with it.
I received operating system files from the vendor to update my unit. I received these three files:
- YMHC0101-N39-2.3.4.3.12_20180601_152348.img
- phonixcard.exe
- mcu-201804260001KC1-1522.img
Unfortunately, I have no instructions on how to do it. Could you write me one by one how to make an update?
_carlos_ said:
Hey,
I have an Android Allwinner T3 device and I have problems with it.
I received operating system files from the vendor to update my unit. I received these three files:
- YMHC0101-N39-2.3.4.3.12_20180601_152348.img
- phonixcard.exe
- mcu-201804260001KC1-1522.img
Unfortunately, I have no instructions on how to do it. Could you write me one by one how to make an update?
Click to expand...
Click to collapse
What problems do you have?
To update the OS:
1. Insert a formatted microSD card in an external microsd reader (computer's internal reader never worked for me)
2. Run phonicard as administrator. Select the .img file (YMHC0101-N39-2.3.4.3.12_20180601_152348.img), select the letter of your microSD, select "product" and hit "Run". After a few minutes you should see a green status bar or a message "Magic Complete/Burn End..." depending on Phonixcard version.
3. Turn off your headunit, remove all usb and sd cards from it, insert your new card in the GPS slot and turn it on. You should see a green bar loading. It takes about 1-2'. When it shows "CARD OK" on screen turn it off and remove the microSD.
4. Turn it on again and it should start booting. The first boot will take longer, 3-5'.
To update the MCU:
You should use another empty and formated microSD card. If you want to use the same, you should format it but also you should delete the hidden partition Phonixcard has created. Open Phonixcard with microSD connected and select "Format to Normal".
1. Copy mcu-201804260001KC1-1522.img in microSD card (copy the file in card, don't use Phonixcard to burn it).
2. Turn on you headunit and allow it to start. Remove all usb and sd cards and insert your microSD (with only mcu update in it).
3. Wait a few seconds and it should open a screen showing you that it found a MCU update. Select it and it should guide you through the process. Don't turn it off. Allow it to finish and reboot.
koroji said:
What problems do you have?
Click to expand...
Click to collapse
For me, there is a problem, that after selecting a home page, applications cyclically appear every 1 second and disappear. You can not start any application.
koroji said:
2. Run phonicard as administrator. Select the .img file (YMHC0101-N39-2.3.4.3.12_20180601_152348.img), select the letter of your microSD, select "product" and hit "Run".
Click to expand...
Click to collapse
Should I do it on my computer or Android Allwinner T3?
Yes, phonixcard is a computer program
Hello,
I have a problem with running the PhoenixCard application. I copied the applications onto the computer and opened it. I ran the PhoenixCard.exe file as an administrator. The user account control window appears: "Do you want to allow the following program from an unknown publisher to make changes to this computer?" I pressed the YES button, but the window disappears and nothing happens.
Please, tell me what to do.
Regards Robert
Write still what you used the phoenixcard version?
Where can I download firmware updates? I can't find vendor website.
You must write to the seller.
I've bought on Amazon... i'm sure that seller will not reply
Try it, I bought it on Aliexpress and the seller is replying to my messages.
---------- Post added at 11:42 PM ---------- Previous post was at 11:07 PM ----------
What is your exact model?
_carlos_ said:
Try it, I bought it on Aliexpress and the seller is replying to my messages.
---------- Post added at 11:42 PM ---------- Previous post was at 11:07 PM ----------
What is your exact model?
Click to expand...
Click to collapse
Czesc,
Pisalem na Elektrodzie do Ciebie w sprawie plikow do radyjka i dzialajacego PhoenixaCarda
Jak masz chwile daj znac lub linka na priv
Pzdr
The procedure has been confirmed in Xda https://forum.xda-developers.com/sho...&postcount=412 and also by myself.
Remember that this procedure makes a full wipe and will erase all the internal memory, it is essential to make a Backup
Instructions
This is the requirements
1- Upgrade with USB-OTG
An OTG cable
A USB drive (8GB at least) Formatted as NTFS or ExFat
Also you can use an USB drive + USB C adapter
download 178 firmware following the link ( thanks @SLVMSF )
https://forum.xda-developers.com/showpost.php?p=79841124&postcount=175
To download 161 firmware just follow the link below ( thanks @SLVMSF )
https://forum.xda-developers.com/showpost.php?p=79660859&postcount=733
To Download .153 -L29
Download VOG-L29C 9.1.0.153 (C431E4R2P2) _Firmware_9.0.0_r3_EMUI9.1.0_05015THP.
https://www.dropbox.com/s/32shgrdzaokswgy/dload_Vog-L29.153.zip?dl=0
: https://transferxl.com/08vY9zCDBTWKdN
To Download .153-L09
look for the right firmware in this page and follow the guide
https://support.halabtech.com/index....older&id=45220
Open the Zip and extract the dload folder on the pendrive
- Turn off the P30 Pro
- Connect the pendrive with the OTG cable
- Now press the three buttons at the same time.
- Volume +
- Volume -
- Power button.
(The p30pro will light up and vibrate, keep the buttons pressed)
Only when you see the blank screen and EMUI appears will you release the buttons.
The flashing will start and lasts about 2 minutes.
After flashing the P30 Pro will restart automatically.
2- Upgrade with NM Card
- Extract the dload folder to the Nm card
- The same option for USB-OTG is valid.
And also you can try this one
- Enter the service menu by dialing * # * # 2846579 # * # *
- Press Option 4. Sofware Upgrade
- Press OPTION 1. Memory Card Upgrade
The device will restart and the update will begin.
I am not responsible for bad use of this guide.
Cheers
Thanks to
@Cambridge for his First full guide on how to flash by dload method
Reserved
juanpirulo said:
The procedure has been confirmed in Xda https://forum.xda-developers.com/sho...&postcount=412 and also by myself.
Remember that this procedure makes a full wipe and will erase all the internal memory, it is essential to make a Backup
Instructions
This is the requirements
1- Upgrade with USB-OTG
An OTG cable
A USB drive (8GB at least) Formatted as NTFS or ExFat
Also you can use an USB drive + USB C adapter
Download VOG-L29C 9.1.0.153 (C431E4R2P2) _Firmware_9.0.0_r3_EMUI9.1.0_05015THP.
https://1drv.ms/u/s!AkomK-CQYJF9ijZmxc4J8GQvIwKf
Open the Zip and extract the dload folder on the pendrive
- Turn off the P30 Pro
- Connect the pendrive with the OTG cable
- Now press the three buttons at the same time.
- Volume +
- Volume -
- Power button.
(The p30pro will light up and vibrate, keep the buttons pressed)
Only when you see the blank screen and EMUI appears will you release the buttons.
The flashing will start and lasts about 2 minutes.
After flashing the P30 Pro will restart automatically.
2- Upgrade with NM Card
- Extract the dload folder to the Nm card
- Enter the service menu by dialing * # * # 2846579 # * # *
- Press Option 4. Sofware Upgrade
- Press OPTION 1. Memory Card Upgrade
The device will restart and the update will begin.
I am not responsible for the bad use of this tutorial.
Cheers
Thanks to
@Cambridge for his First full Tutorial on how to flash by dload method
Click to expand...
Click to collapse
Actually, option 1 using both volume keys and bower key works on NM card as wel. No need to enter the service menu.
wow, thanks for work.
Where can i download VOG-L29 version C605 ?
-Zork- said:
wow, thanks for work.
Where can i download VOG-L29 version C605 ?
Click to expand...
Click to collapse
https://support.halabtech.com/index.php?a=downloads&b=folder&id=44877
USB otg mode is workking.
It's so simple !!
Thanks OP.
Option 1 and 2 work with either NM or USB-OTG drive
It did not work well with my device.
I tried in OTG mode.
The environment is 9.1.0.124 (C431E4R2P2).
When you start eRecovery, it becomes Software installed failed. (Incompatibility with current version)
What's wrong
Have you downloaded all the files and placed the three update files in to a folder called 'dload'?
Also, if having issues try the service menu method.
Don't let me download the firmware ?. I have what could it be?
takato23 said:
Don't let me download the firmware . I have what could it be?
Click to expand...
Click to collapse
try again here https://1drv.ms/u/s!AkomK-CQYJF9ijZmxc4J8GQvIwKf if its not working just follow the link to the direct download below
just download from here, https://support.halabtech.com/index.php?a=downloads&b=file&c=download&id=121664 , you will have to register first to download.
something is not going well with the drive link i put on first post. cheers
If it will not allow you to download due to too many people accessing the file, then add it to your drive. once there, right click and select "Create copy" you can then download the copy
i am trying to upload to mega. if someone have a valid link and want to share here please just post it. cheers
Unable to locate L09 firmware v 153. Don't think it's available yet.
153 firmware for C185 is available now in Halabtech. Just flashed it.
Hi All
I'm on 3 UK and when I inserted my sim it downloaded 3UK splash screens and apps etc. Can I flash this over my current 3 branded firmware using the USB-OTG method and will it still have all the 3UK customisation afterwards or will it debrand, if it will debrand it is there any way I can stop this happening again. Sorry for all the questions
Thanks in advance
csw43 said:
Hi All
I'm on 3 UK and when I inserted my sim it downloaded 3UK splash screens and apps etc. Can I flash this over my current 3 branded firmware using the USB-OTG method and will it still have all the 3UK customisation afterwards or will it debrand, if it will debrand it is there any way I can stop this happening again. Sorry for all the questions
Thanks in advance
Click to expand...
Click to collapse
You asked at just the right time, my device was a branded ThreeUK device... I just flashed it 30 mins ago on my device. Completely debranded it, however when you setup the phone it will give you an option to "Update" to a new custom version which is the carrier modified firmware. Presume this will rebrand it so i simply skipped it, note however it shows as update available in settings still if you want to install it in future manually. That being said... I wonder if it's possible to extract and see what this "Update" contains since it's 176MB which is a lot. Whether any optimisations ect are worth it for the branding.
That's great, thank you for the info! It really is a crap idea to customise a device based on operator sim card.
I will have a go at flashing this now, I've already downloaded the files
Thanks again
Hello, anybody know where I can find a firmware for the VOG-L04? Thanks in advance.
links not working guys, any others to try? Have signed up to website but file is blocked; too many DL's. Need this real bad, didn't realize Funky H puts files up that fail safety net after flash Thanks
[ROM] REVOLUTION_TEAM H96 MAX X2 2GB/4GB U211 ANDROID 8.1 [ATV] (2GB OPTIMIZED – WIFI – BLUETOOTH)
WARNING:I'm not responsible and nor the forum that hosts my ROM is, of any damage or malfunction caused on your device, during the flash or the use of my ROM.
You'll take the responsibility of what you do.
V. 1.0
THE ONLY FIRMWARE H96 MAX X2 2GB WORKING WITH WIFI – BLUEETOOTH – NETFLIX HD – PRIME VIDEO HD – AIR PLAY ENABLED ON H96 MAX X2
SMARTYOUTUBE AUTOMATIC RESOLUTION SET (DON’ T CHANGE OPTION) 8K ENABLED
DON’T UPDATE NETFLIX AND PRIME VIDEO FOR CORRECTY USE
- CHROMECAST VERSION IS LASTEST VERSION NOVEMBER 2019
- PLAYSERVICES GOOGLE NOVEMER 2019 FOR ATV
- GOOGLE PLAY STORE NOVEMBER 2019 FOR ATV
Changes/Mods:
1. OPTIMIZED FOR 2GB VERSION
2. WIFII WORK
3. BLUETOOTH WORK
4. TWRP RECOVERY INSTALLED
5. ROM BASED OF BEELINK’ S FIRMWARE
6. TOP STATUS BAR REMOVED FOR ATV EXPERIENCE
7. NETFLIX HD WORKS
8. PRIME VIDEO HD
9. APP KODI, SMARTYOUTUBE,APTOIDE 5.2, FILE MANAGER,AIRSCREEN,ECC..
10. 4K FORMAT ADDED FOR H96 MAX X2
11. NO ROOT (SuperSU FILE INCLUDED – INSTALL FROM TWRP IS NEEDED)
12. ADD MULTI WEBWIEW OPTION
13. ADDED ANDROID TV REMOTE CONTROL
14. VOICE RECOGNIZED
15. HDMI CEC WORK
16. DROID SETTING FULL
17. DLNA, AIR SCREEN MIRACAST SUPPORT
18. ANDROID APP DRAWERS FREE PRE INSTALLED FOR NO ATV APPS
19. SOME OTHERS
BUGS:
In 2gb versions Youtube sometimes crash, (ALWAYS AT THE FIRST TIME) for this reason is pre-installed SmartYouTube that work perfectly and if you want can install automatically ATV YOUTUBE TV BRIDGE (YOUTUBE ITSELF PERECTLY WORK).
For some bugs report me.
COOMING SOON: PIE FASTEST VERSION
Download Link
H96 Max X2 Porting
Bye
how to install ?
How to install this Rom over the uptade App or via flashtool?
Hi
Super Rom when is the android 9 version coming?
And the LEDs are not working properly.
It stays blue in standby and does not turn red
Hello !
It works very well on my H96 Max X2 4/32 wich was not ATV
I have try so many ROM.... Sometime, the wifi doesn't work (either the start with remote), sometime IPTV software crash.
Your ROM is fine and everything is OK (wifi, IPTV, remote, Led, Youtub, Play store....). Fast and fluid with your ATV 8.1.
I am waiting for the ATV 9.
Thanks a lot !!!
ctk69 said:
Hello !
It works very well on my H96 Max X2 4/32 wich was not ATV
I have try so many ROM.... Sometime, the wifi doesn't work (either the start with remote), sometime IPTV software crash.
Your ROM is fine and everything is OK (wifi, IPTV, remote, Led, Youtub, Play store....). Fast and fluid with your ATV 8.1.
I am waiting for the ATV 9.
Thanks a lot !!!
Click to expand...
Click to collapse
Hello, I am very pleased that Rome works so well for you.
Could you please explain to me how you installed this Rom?
did you just use the update app that came with the original rom or how did you do that, there is supposed to be a flash tool, i would like to copy it for you, i have the same box and it always crashes with the original firmware, thank you very much.
gruft2 said:
Hello, I am very pleased that Rome works so well for you.
Could you please explain to me how you installed this Rom?
did you just use the update app that came with the original rom or how did you do that, there is supposed to be a flash tool, i would like to copy it for you, i have the same box and it always crashes with the original firmware, thank you very much.
Click to expand...
Click to collapse
It is easy. You need to flash the android Tv box (search on youtub "how to flash H96 max2")
It is always the same with Amlogic CPU. You need to use USB burning tool and a USB cable with 2 males.
Don't be worried about doing this. I was a little anxious the first time i do it, but it is really easy.
I try many ROM for my H96 Max X2 4/32. This one is the best. The original ROMS are very bad (you can found them on the web "h96tvbox").
Tell me back if you success !
thanks a lot for the help, i ordered the right cable, as soon as it is there i will test it, thanks for the quick answer i will contact you again and share my experience
Hi
hdmi cec is not running. As soon as I activate the option, I can no longer start the box using the remote control.
then it only helps to take electricity and plug it in again.
Hello I need urgent help, when trying to flash the ROM I always get the error " 0x10401001 Romcode/BI2_Boot stage Error" what can I do?
Hello. please, is there any tutorial on how to flash? USB burning tool freezes at 3 % and AMLogic Flash Tools can't flash the rom, only Bootloader or Recovery. Thank you.
unions8 said:
Hello. please, is there any tutorial on how to flash? USB burning tool freezes at 3 % and AMLogic Flash Tools can't flash the rom, only Bootloader or Recovery. Thank you.
Click to expand...
Click to collapse
check your H96Max x2, maybe it is a different version as mine.
AIDA64 says the board as franklin , not u211 based.
this firmware is for u211 based one.
mine has LPDDR3 ram and says g12a_u212_4g.
If you have a chance to update this firmware, the board has bricked at BL2 stage memory init process.
So far, i have no chance to replace my device's firmware with every firmware downloaded from net.
Hi, i have this box if i plug the usb my box turn on but nothing on pc . its' appear disconnected to him. Do you have an idea ? Thanks (sorry for my english)
Hi have resolved my problem but now i have "boot stage error"...
---------- Post added at 09:18 PM ---------- Previous post was at 08:27 PM ----------
blust0ne said:
check your H96Max x2, maybe it is a different version as mine.
AIDA64 says the board as franklin , not u211 based.
this firmware is for u211 based one.
mine has LPDDR3 ram and says g12a_u212_4g.
If you have a chance to update this firmware, the board has bricked at BL2 stage memory init process.
So far, i have no chance to replace my device's firmware with every firmware downloaded from net.
Click to expand...
Click to collapse
Hi, mine says U211 but any rom working. I have updated to official firmware and only one working, rom android 9.0 for LPDDR3 and now aida says Franklin ! it's very strange... any rom are compatible with U212 ???
my only one firmware is "aml_s905x2_9.0_H96Max_X2_mac_wifi_20190920.img" .
But I got the device with firmware dated oct or nov .
On my research, my firmware is more similar with S905x3 ones.
Now my plan is the change of the home launcher only.
【2019 TV BOX / 4GB + 64GB】H96 MAX Android 8.1 TV Box 4G + 64G Amlogic S905 X2 Quad Core ARM Cortex A53 Smart Set-top box, Support 2.4G / 5.8G
I have this one, can I install this rom successfully?
very good rom, thanks
is it possible to get the status and navigation bars back?
Hi guys,
There is two versions of H96max2 (they are exactly the same when you look at the box)
- the DDR4 one, some time name "u211". This firmware is Ok for this one. And a lot of others too.
- the LPDDR3 one, some time name "aml". This firmware not loading and do 3% error boot. For this one, you can install firmware from web site 4pda (look for H96max2). You must take the aml "ANDROID TV 9 vietnamien"
It works well, you need ton change language first if you are not russian (!).
Lovely rom, works so God damn well. You revived this box for me, I cannot wait for the pie version.
For update H96 Max X2
Thank you for this firmware is all i want, :victory:
best way for the update
1. Download Burn Card Maker --
2. Format fat32, your microSD card (not greater than 8GB ) -- formatting with your pc not with the utility ( He broke my 32GB sdcard)
3. Check yes (normal sd bootloader)
4. check yes (force erasing) flash
5. open your img file (that you download from this site)
6. Power off your Device, and unplug it from the power source
7. put your microSD card in your device (they have 3 files)
8. take the toothpick and place it inside the AV port, holding the button down then connect your box and power it up, keep the toothpick in place to hold the button down until the logo emerges.