hello.
How do I enable Mi10's diagnostic mode?
Things I tried:
1. Unlock bootloader
2. Install TWRP
3. Install Magisk
4. Enter the following command
adb shell
su
setprop sys.usb.config diag, adb
I don't see the qualcomm serial port device in the device manager, just the device like the image.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
alphonsezero said:
hello.
How do I enable Mi10's diagnostic mode?
Things I tried:
1. Unlock bootloader
2. Install TWRP
3. Install Magisk
4. Enter the following command
adb shell
su
setprop sys.usb.config diag, adb
I don't see the qualcomm serial port device in the device manager, just the device like the image.
View attachment 5024589
Click to expand...
Click to collapse
mi 10 does not enter diag mode. I tried a lot but the result failed
@here Please provide a method how to open mi 10 5g diag port.
Related
this is alternative way to root the Huawei Mediapad 7 lite
credits vampirefo for his id command root check
my model was/is S7-931w which has wifi
1) use google playstore to install a terminal apk
2) download an apk to sdcard called Root Master (english Version).apk
http://www.nextwap.net/mobile/vE4C-rxxce/root_master__english_version_.html
3) allow your device to install unknown sources
4) install apk and open it
5) you will see 3 options, system info....root....and manager......choose the middle one
it will take some time with some animation
the first time it ran.....I checked inside the terminal to see if id command worked correctly.....it did not
6) reboot the phone and try again
If successful, in a terminal you are looking for the su command to change the prompt from $ to #
AND then run the id command and you must see only 2 responses...... user id and group id
---if you get a third response you have to redo it and reboot it
correct image is attached
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How to Unlocking the Bootloader LG L1 II
E410/11/15
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Requirements:
LG L1 II rooted (How to Root here)
Terminal Emulator
bootloader-L1 here
steps:
Download the bootloader-L1 ( link above)
Unpack "bootloader-L1" in "internal memory" (/sdcard)
Open the terminal and run these commands
su
cd sdcard
sh unlock.sh
Done Bootloader Unlocked
[/LIST]
i did it for training, but then i tested fastboot device-info and it showed locked.
then with fastboot oem unlock it worked. would it work without it?
How to enter fastboot mode?
johnny_s23b said:
i tested fastboot device-info and it showed locked.
Click to expand...
Click to collapse
How did u enter on fastboot mode? I can't find the correct key combination, and adb reboot-bootloader doesn't work...
EDIT: I've used an TWRP Installer APK which just unlocked bootloader and installed twrp, rebooting to it and now I can enter fastboot by rebooting to bootloader in TWRP
Hello there!
I wanted to unlock the bootloader of my phone (Lenovo Zuk Z2 Plus), but the my phone is not being recognised as an ADB device in the CMD. I have installed the following drivers:
1. ADB Setup v1.4.2
2. Samsung-Usb-Driver-v1.5.45.0
3. Zuk USB Driver 1.0.8
The developer options have been unlocked and I have enabled USB Debugging. The RSA popup appeared right away on my HTC and Samsung phones, but is not appearing only on my Zuk Z2.
I tried doing the following things:
1. Reinstalling drivers
2. Deleting C:\Users\<username>\.android folder
3. Formatted my phone.
The phone is being shown under two categories, one being "Portable Devices->ZUK Z2132" and the other being 'ShenQi ADB Device->ShenQi Composite ADB Interface" in device manager.
Any help would be appreciated.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The problem has been solved. I used the below toolkit and was lucky enough to get the RSA popup.
https://forum.xda-developers.com/zu...ol-one-driversunlocktwrpfactory-t3432782/amp/
After flashing a custom ROM, I'm able to get the popup.
For some reason, few cases present the generic and ugly message of bootloader unlocked, and not the original of Xiaomi and here I have the solution.
If you have a uggly bootloader message, like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
And you want the common image with a padlock, similar to this (but not the same):
You only need follow the next simple instructions, you have 2 ways to do.
First way - ADB Recommended
1. Install or download adb from here.
2. Conect your phone on fastboot mode.
3. Download and extract the attachment file on the same folder than adb.
4. In the same folder of adb, open a terminal (cmd, powershell) and type: "fastboot flash logo logo.img" (without quotation marks obviously).
Second way - TWRP CN
1. You need the TWRP CN (not multilanguage).
2. Download the attachment file, unzip and put on your internal memory.
3. Reboot on TWRP.
4 Choose "IMG" on the install section.
5. Select the logo.img and fhash.
I hope it will be you useful.
Yes you can do it .you need to install twrp cn to perform it... download this from below link...
Unofficial TWRP 3.4.2b Recovery for Redmi 9 (lancelot/Indian Prime) - Miui 11.
Source: https://unofficialtwrp.com/xiaomi-redmi-9-root-twrp-3-4-1/ The author wrote this: all issues fixed! Thanks to the developer for the energy and time. Developer: wzsx150. This is a working unofficial TWRP recovery for Redmi 9 for Miui...
forum.xda-developers.com
And go to your recovery mood...
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Important:do to enter 'fastboot boot fastboot' cnd when you have custom recovery installed...it must break your device...
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
After going recovery follow below steps...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now connect your device to your PC and go to device manager to your PC and you can find 'fastboot' device under other device catagory..
You need to install fastboot' driver ..if you have then no need to install or download and install from below link...
10.59 MB file on MEGA
mega.nz
After install right click on the 'fastboot' and select update driver and follow the steps...
Now you can use all fastbootd cmd with your custom recovery...no need stock recovery at all.....tnx