Hi i have a T95 S1 and its been connected to the car tv for the last year and working great but now i cant get past the loading splash screen.
i know the issue has been caused by not shutting it down before the power is cut but since its in a car.
1 I have tried to reset it with a toothpick in the av port but it wont do anything.
2 i have opened it up and shorted the reset switch pins just to make sure its not an issue with the switch but still nothing
3. i don't have a type a to a USB cable so i made my own with 2 USB extension cables
4. i have tried connecting it to the PC with the DIY USB cable and windows makes the noise on something been connected but i don't see it displayed in the factory tool.
5. i have triad to use the amlogic sd card tool and installed the image onto sd card but i cant get it to run as i cant get into the recovery.
EDIT** Uart log on boot
HTML:
https://pastebin.com/dAdD0yAr
Any help be greatly appreciated..
View attachment 5034761
View attachment 5034763
View attachment 5034765
View attachment 5034767
Related
I have searched all the threads I can find and can't find an answer so please forgive me if this is a common problem.
To make a long story short I had to replace my LCD and then the digitizer stopped working. I did a factory reset which solved the problem but then when I tried to install my backup I messed everything up and nothing was working. I could no longer connect any computer to my phone using several different USB cables. All my google services were not working along with my proximity sensor and light sensor.
I was able to get a fenny rooted stock rom to install using Mobile Odin Pro and I seem to have most of everything working again except the USB port.
I was unable to connect to a computer or charge. After trying everything I could find online including factory resets, *#0808# settings, USB debugging mode, I broke down and ordered a new USB port which I installed into my phone and I am having the same problem with the new port installed.
When I plug my phone into the charger it does nothing however if I turn the screen off and wait about 3 to 5 minutes the LCD will light up and indicate that it is charging and then the phone takes a charge. If I use the phone while it is plugged in it will never indicate that it is charging, I have to power the screen off for several minutes. I have tried a second known good battery and I have the same issue. I have tried two separate factory chargers which both work fine on my wife's S4 and neither work properly with my phone.
When I plug it into my computer I do not get the normal message to select MTP or camera. using the settings recommended on *#0808# of USB of AP and USB Settings of MTP + ADB.
If I use *#0808# and select CP under the USB tab and then plug the phone into my computer I hear my computer instantly make the sound it usually makes when you plug a usb device in but nothing else happens. This same computer works fine with my wife's other Galaxy S4 and I have tried this on three separate computers with the same result so I don't think it is a computer or usb cable issue.
Is there a way that I somehow deleted drivers or a file on my phone that controls the USB port? I am unable to attach screenshots on this post for some reason so below is what my about phone screen shows. Is it possible I have the wrong kernel or radio installed that could be causing this issue?
Model Number
SGH-M919
Android Version
4.4.2
Baseband Version
M919UVUEMK2
Kernel Version
3.4.0-g4224a08-dirty
[email protected]#8
Tue Mar 25 18:18:23 MDT 2014
Build Number
KOT49H.M919UVUFNB4
SE for Android Status
Permissive
Secure boot status
Type: Samsung
Security Software Version
MDF v1.0 Release 2
When I dial *#0808# this is what I see
USB
______________________________________
() CP
(*) AP (I selected AP)
USB SETTINGS
_______________________________________
(*) MTP (this is currently selected)
() MTP + ADB (I have tried this setting also and it did not work)
() PTP
() PTP + ADB
() RNDIS + DM + MODEM
() RMNET + DM + MODEM
() DM + MODEM +ADB
OK REBOOT
I would really appreciate any help someone can give me. Thank you in advance. If anyone is local to Rhode Island and willing to help me out in person I would be willing to pay you for your time, I just want to get this to work as I use my phone for work and need to be able to transfer files to my computer.
Last night I changed the SD card and when I did I plugged it into my computer and it started to charge. After about 10 minutes the computer beeped and I was now able to access my files on both my phone and SD card but it was not showing as connected using Kies.
It worked off and on today but now when I plug it in device manager shows qualcomm CDMA technologies MSN with a yellow explanation point saying driver not installed. When I plug my wife's s4 into this computer it works fine. Is it possible my s4 is somehow showing up to my computer as a galaxy note? That is the phone that I find in Google when I search that qualcomm driver.
Hello, I have issues connecting my S3 international model (i9300) to any PC. It has CM11 since at least 6+ months and it worked just fine and connected to my PC two days ago just fine.
Some days ago, it started bootlooping because of the common power button stuck problem [turned on by itself when battery inserted, and rebooted in the Samsung logo, which doesn't even let you go to DOWNLOAD mode or Recovery because it just reboots after a few seconds]
Yesterday I disassembled it following fixit guides and youtube step by step guides to make sure I didn't break anything. I saw the button problem was internal (the button apparently works fine, but internally it has a closed circuit so it seems as pressed). I assembled my phone again and went to bed. Today it was working without bootloop. I saw this as an opportunity to make all the required backups just in case it went to bootloop again but I couldn't get anything from it. Windows doesn't recognize it at all, not even during boot. Here is what I tried:
*Tried in several PCs/Notebooks/OS with different cables that work with other phones
*In all cases it charges the battery, but the PC doesn't see it as a device.
*I rebooted the phone by software (so I don't press the power button at risk of getting bootloop again) going to terminal emulator and using 'reboot' command.
*Rebooting the phone connected to the PCs doesn't either cause any device to be detected by the PC during the booting of the phone.
*Thinking it might be the port of my phone, I tried an OTG adaptor and several pendrives. They all were detected by the phone and I was able to write and read the USB drives.
Click to expand...
Click to collapse
At first I suspected I left a ribbon/flex cable not connected to the board, but being able to use OTG USB drives and being able to charge it didn't convince me it was the case. I want to avoid disassembling it without knowing first which ribbon to look at and any other test/information you could tell me to provide in order to find the solution.
I tried to flash the ATV Xperience rom using the steps shown in the Youtube tutorial, but I could never get the USB Burning Tool to even recognize my box. It's not the tool per se, but that my computer never sees a USB connection when connecting the A95X MAX OTG port to my PC. So here's a list of stuff I've tried:
1) Connect the OTG port of the A95X MAX (the USB 2.0 port next to the HDMI) and connected that into the Amlogic's Burning Tool, device does not show up in the list, no power plug.
2) Connect the OTG port of the A95X MAX, with power plug. Device still does not show up.
3) Connected HDMI from TV to the A95X MAX, held down reset button inside the A/V 3.5mm port, plugged in the DC plug, kept holding it down, never saw recovery.
4) Box used to boot after a long wait, but it doesn't even boot anymore.
mayb this video can help..
https://m.youtube.com/watch?v=2ZfLxgJtmps
or just ask at freaktab forum....
https://forum.freaktab.com/forum/tv...al-wifi-gig-lan-bt4-2-support-2-5inch-ssd-hdd
missing the driver for your android box.
reinstall usb burning tool, it should ask to install a "worldcup" driver as well.
some Android boxes dont like USB 3 (Cable or ports)
Thanks for the suggestions, none of them worked, I pulled the damn thing apart and reflowed the usb connectors and its ESD diodes.
Chinese designed anything is just absolute garbage, learned my lesson with Teclast and Amax, won't be repeating this again, gonna give my money to Samsung from here on out, their software isn't great, but they can make some damn fine hardware...
Watch this installation guide video, if you want to install ATV Xperience without PC/LAPTOP.
I've been booting LibreELEC/CoreELEC from SD card on my AZW (Beelink) W95 (S905W) box for years now. Yesterday I tried booting into the stock Android system (7.1 I think- I haven't done it for a while) but it wouldn't boot. Not being one to leave well enough alone I decided to try a reset using a toothpick in the reset hole by the power plug. It flashed the start screen for a split second and then stopped. After that it wouldn't boot off the CoreELEC SD card either.
I've tried a clean CoreELEC install, stock firmware, Amlogic Burn Card Maker, and TWRP on the SD card - none of them get me past a black screen.
I don't think the reset button is doing anything (I depress it while plugging in the power jack). In fact, I don't know if it ever worked. My box had previously always booted off a SD card if it was inserted in the slot without having to do anything special.
My box isn't completely dead but comatose. The signs of life are:
1) The blue LED comes on when I plug in the power cord.
2) After about 20 minutes or so the blue LED will go off. If I press the power button on the remote it comes back on.
3) My router sees it on my network as active. But I get connection refused when I try access it using Windows File Explorer or try to SSH into it using Putty.
4) When I insert a SD card into the slot it writes Andriod and LOST.DIR folders to it.
I haven't tried the Amlogic USB Burning Tool yet because I don't have an USB 2.0 Type A male to male cable - but I've ordered one. My concern is I won't be able to put it in reset mode since I'm not sure the reset button does anything (but I can feel it click).
Is there anything else I should try while I'm waiting for my cable to arrive?
Any recommendations on how I should proceed once my cable arrives?
Thanks
RKCRLR said:
I've been booting LibreELEC/CoreELEC from SD card on my AZW (Beelink) W95 (S905W) box for years now. Yesterday I tried booting into the stock Android system (7.1 I think- I haven't done it for a while) but it wouldn't boot. Not being one to leave well enough alone I decided to try a reset using a toothpick in the reset hole by the power plug. It flashed the start screen for a split second and then stopped. After that it wouldn't boot off the CoreELEC SD card either.
I've tried a clean CoreELEC install, stock firmware, Amlogic Burn Card Maker, and TWRP on the SD card - none of them get me past a black screen.
I don't think the reset button is doing anything (I depress it while plugging in the power jack). In fact, I don't know if it ever worked. My box had previously always booted off a SD card if it was inserted in the slot without having to do anything special.
My box isn't completely dead but comatose. The signs of life are:
1) The blue LED comes on when I plug in the power cord.
2) After about 20 minutes or so the blue LED will go off. If I press the power button on the remote it comes back on.
3) My router sees it on my network as active. But I get connection refused when I try access it using Windows File Explorer or try to SSH into it using Putty.
4) When I insert a SD card into the slot it writes Andriod and LOST.DIR folders to it.
I haven't tried the Amlogic USB Burning Tool yet because I don't have an USB 2.0 Type A male to male cable - but I've ordered one. My concern is I won't be able to put it in reset mode since I'm not sure the reset button does anything (but I can feel it click).
Is there anything else I should try while I'm waiting for my cable to arrive?
Any recommendations on how I should proceed once my cable arrives?
Thanks
Click to expand...
Click to collapse
Hi, your device seems to be in a strange state currently, only thing i can reccomend is trying a few firmwares to see what works for you, you should be able to flash most s905w based roms, if your device cant be detected by USB burn tool you might need to use ask Rom Mode" to force your box to be detected by burn tool, this makes it almost impossible to brick a box
Thanks for the suggestions, I'm a complete newbie at this.
Is the Ask ROM Mode an option in USB Burning Tool?
I have an OEM W95 firmware update file (in both .img and and an OTA in .zip format) but they may be older than what is currently on the box. I also found a TWRP file for the S905W. But I don't know how to use any of these.
I downloaded the AMLogic Tools 6.0.0 and tried the AMLogic Flash Tool since it seems to work through the Ethernet port. I assumed this because you access the box via an IP address but I really don't know. I watched the video but couldn't find any detailed instructions on how to use it.
When I pressed the Connect button it said it connected and I had the green Connected display (I was connecting through my LAN - I don't know if I should connect directly with an ethernet cable). I loaded my .img file and said Flash. It says it is flashing and a second or so later it says SUCCESS! However the box still doesn't boot. I tried both Boot and Recovery (I don't know which option I should choose). I think that the SUCCESS! message is incorrect since I get the message even if I press the Flash button without the box connected. However, I can't connect to the box without the ethernet cable connected so the connected message seems correct.
Am I using the AMLogic Flash Tool correctly?
I was thinking about trying the S905W atvExperience ROM but thought I'd wait until I got my USB cable before before doing something more drastic.
Any other suggestions?
Thanks
OK, so my male to male USB cable arrived and I managed to get my box un-bricked using AMLogic USB Burning tool with a factory .img file. It took several tries. I kept getting errors when it tried to erase the bootloader or would get to 7%, progress would stop for about a minute, and then Burning Tool would close.
I finally got it to proceed all the way by holding in the reset button, plugging in the USB cable (no power cable), and keeping the reset button pushed the whole time (I don't know if this was just a coincidence). Also, I hadn't closed Burning Tool after the previous error erasing the bootloader. I'm posting all this in case someone else has a similar problem.
After that, it still wouldn't boot of the CoreELEC SD card with the reset button pushed down. It would go straight into the Android OS. I got it to boot into CoreELEC by installing the Reboot to LibreELEC app. Now it always restarts in CoreELEC the way it used to when the SD card is left in. I think this is how I got LibreELEC working years ago.
So, now I'm contemplating installing atvXperience but I have a couple of questions:
What would be the best way to install atvXperience without being able to the reset button to put the box into recovery mode?
What would be the best way to prepare for not being able to use the reset button to put the box into recovery mode if something were to go wrong during flashing?
Thanks for any help.
OK, so my male to male USB cable arrived and I managed to get my box un-bricked using AMLogic USB Burning tool with a factory .img file. It took several tries. I kept getting errors when it tried to erase the bootloader or would get to 7%, progress would stop for about a minute, and then Burning Tool would close.
I finally got it to proceed all the way by holding in the reset button, plugging in the USB cable (no power cable), and keeping the reset button pushed the whole time (I don't know if this was just a coincidence). Also, I hadn't closed Burning Tool after the previous error erasing the bootloader. I'm posting all this in case someone else has a similar problem.
After that, it still wouldn't boot of the CoreELEC SD card with the reset button pushed down. It would go straight into the Android OS. I got it to boot into CoreELEC by installing the Reboot to LibreELEC app. Now it always restarts in CoreELEC the way it used to when the SD card is left in. I think this is how I got LibreELEC working years ago.
So, now I'm contemplating installing atvXperience but I have a couple of questions:
What would be the best way to install atvXperience without being able to the reset button to put the box into recovery mode? (I did try flashing atvXperience once using USB Burning Tool but I got the same error erasing bootloader)
What would be the best way to prepare for not being able to use the reset button to put the box into recovery mode if something were to go wrong during flashing?
Thanks for any help.
Another follow up post for anyone with the same problem. I did some searching and found out I'm not the only one with a box that the reset button doesn't work. A work around for them was to connect the male to male USB cable, load the image into Burning Tool, press Start, and then plug in the power supply. The image file would then start flashing.
However, my box would start booting as soon as I connected the USB cable (didn't need the power supply). So I loaded the image into Burning Tool, pressed Start, and then connected the USB cable. This appears to be the work around for my box (I probably did this when I got my box to recover the first time - holding the reset button was probably irrelevant).
This procedure works for the stock firmware but when I try to flash the atvXperience image file the box hangs at 7%. So I still need some help there.
Also, is there a ATV ROM better suited for my S905W box (2/16 GB)?
W95 is really ****ing box whenever you feel you get off from the current problem will be into next one.
I have installed atvx Rom but afterthat when I tried adian rom my device bricked.
Without Ubt flashing it's connect but as I start flash it's sound unknown device and give flash error
Hi all,
I'm in a complete head spin so I'm hoping someone here could shed some light on an issue I'm facing.
As the title says, I currently have a Buzz TV XPL 3000 android box. I'm trying to flash "Aidan's Android TV Custom Rom" onto it. But no matter what I try to do, I simply cannot get the Buzz TV box to interact with my Windows 10 PC.
I have 2 different male-to-male USB cables that I've tried plugging into the box and into my PC, but there is no link between them. The PC nor the Android box don't acknowledge any kind of connection. I know a lot of people will probably say that my cables aren't data cables, but I've actually used one of them previously to flash another Android device.
Whenever I plug the USB cables into my Android box and PC, the ONLY thing that happens, is the PC powers up the Android box. I've tried turning on USB debugging tools from the developer menu, but nothing. The PC doesn't even make a sound when I plug the cable in and there is nothing listed under device manager. Nothing appears on USB Burning Tools under devices.. Just nothing.
I've tried plugging in the USB cable, while holding down the reset button (located on the bottom of the box), but all that does is power on the Android box and load into "Android Recover". Still nothing detected on USB Burning Tools and still no acknowledgement from the PC that a USB device has been connected.
The options I get in the Android Recovery menu are:
Reboot System Now
Apply Update From EXT
Apply Update From Data
Wipe Data/Factory Reset
Wipe Cache Partition
Burn Keys
I've tried selecting "Apply Update From EXT" and manually selecting the .img file. But it says it cannot verify the signature.
I'm literally out of ideas. Can anyone who knows what they're doing please help me!
TheOneIsBack said:
Hi all,
I'm in a complete head spin so I'm hoping someone here could shed some light on an issue I'm facing.
As the title says, I currently have a Buzz TV XPL 3000 android box. I'm trying to flash "Aidan's Android TV Custom Rom" onto it. But no matter what I try to do, I simply cannot get the Buzz TV box to interact with my Windows 10 PC.
I have 2 different male-to-male USB cables that I've tried plugging into the box and into my PC, but there is no link between them. The PC nor the Android box don't acknowledge any kind of connection. I know a lot of people will probably say that my cables aren't data cables, but I've actually used one of them previously to flash another Android device.
Whenever I plug the USB cables into my Android box and PC, the ONLY thing that happens, is the PC powers up the Android box. I've tried turning on USB debugging tools from the developer menu, but nothing. The PC doesn't even make a sound when I plug the cable in and there is nothing listed under device manager. Nothing appears on USB Burning Tools under devices.. Just nothing.
I've tried plugging in the USB cable, while holding down the reset button (located on the bottom of the box), but all that does is power on the Android box and load into "Android Recover". Still nothing detected on USB Burning Tools and still no acknowledgement from the PC that a USB device has been connected.
The options I get in the Android Recovery menu are:
Reboot System Now
Apply Update From EXT
Apply Update From Data
Wipe Data/Factory Reset
Wipe Cache Partition
Burn Keys
I've tried selecting "Apply Update From EXT" and manually selecting the .img file. But it says it cannot verify the signature.
I'm literally out of ideas. Can anyone who knows what they're doing please help me!
Click to expand...
Click to collapse
Hi, You Might Have To Try And Figure Out Mask rom Mode To Force your Device To Be Detected By USB Burn Tool If Using The Reset Button is Unsuccessful, Look For Mask rom Mode Information, You Can Upload Pictures Of Both Sides Of Your Logic Board we can try and figure it out
aidanmacgregor said:
Hi, You Might Have To Try And Figure Out Mask rom Mode To Force your Device To Be Detected By USB Burn Tool If Using The Reset Button is Unsuccessful, Look For Mask rom Mode Information, You Can Upload Pictures Of Both Sides Of Your Logic Board we can try and figure it out
Click to expand...
Click to collapse
Hey man,
Thanks for taking the time to reply.
I managed to get it working. Decided to give it another shot this morning and for some reason, first time around it worked. USB Burning Tool instantly picked the box up, installed perfectly and now I have it up and running!! It definitely seems a lot more snappier than my last firmware.
I do have a question though. With the previous stock firmware, my TV would pick the Android box up with a HDR signal. It no longer does this now. Is that to be expected with this rom or is there something I need to do?
Sir
TheOneIsBack said:
Hi all,
I'm in a complete head spin so I'm hoping someone here could shed some light on an issue I'm facing.
As the title says, I currently have a Buzz TV XPL 3000 android box. I'm trying to flash "Aidan's Android TV Custom Rom" onto it. But no matter what I try to do, I simply cannot get the Buzz TV box to interact with my Windows 10 PC.
I have 2 different male-to-male USB cables that I've tried plugging into the box and into my PC, but there is no link between them. The PC nor the Android box don't acknowledge any kind of connection. I know a lot of people will probably say that my cables aren't data cables, but I've actually used one of them previously to flash another Android device.
Whenever I plug the USB cables into my Android box and PC, the ONLY thing that happens, is the PC powers up the Android box. I've tried turning on USB debugging tools from the developer menu, but nothing. The PC doesn't even make a sound when I plug the cable in and there is nothing listed under device manager. Nothing appears on USB Burning Tools under devices.. Just nothing.
I've tried plugging in the USB cable, while holding down the reset button (located on the bottom of the box), but all that does is power on the Android box and load into "Android Recover". Still nothing detected on USB Burning Tools and still no acknowledgement from the PC that a USB device has been connected.
The options I get in the Android Recovery menu are:
Reboot System Now
Apply Update From EXT
Apply Update From Data
Wipe Data/Factory Reset
Wipe Cache Partition
Burn Keys
I've tried selecting "Apply Update From EXT" and manually selecting the .img file. But it says it cannot verify the signature.
I'm literally out of ideas. Can anyone who knows what they're doing please help me!
Click to expand...
Click to collapse
i just bought this buzz tv box. can you guide me ? Like how to root? Which is the best rom? Best apps ? Adaway etc?