Hello, My N6 finally blew its battery. Swelled up badly. I can find plenty of battery.
I have watched all the videos. Seems like an easy project compared to other phones.
The back is already off.
What I am worried about is all the comments about stripped screws from cheap screwdrivers. It seems the screws are an odd size. T3-2.3MM.
I have searched and searched. I can not find a T3 torx screwdriver for 2.3MM?
Am I missing something? I just want to make sure I get a good one. Yes, I have to end w question. Does anyone know where I can purchase a good screwdriver to work with? Thank you in advance.
Wiha 96703 Torx Screwdriver with Precision Handle, T3 x 40mm
eBay Item# 252175071493
Also on Amazon & elsewhere. Wiha is quality. Read the reviews on Amazon, you will be assured.
Related
Does anyone have a recommendation of where to find replacement screws for the Rezound? I've tried Amazon, eBay, etc. and no luck. I ended up ordering screws from similar HTC phones, but the screws turned out to be smaller. Just about all of my screws are stripped from using the wrong TORX driver... ended up having to use a screwdriver just to get them out to replace the digitizer. Any help is greatly appreciated.
Wow, I've never gone as far as to actually disassemble my HTC phone before. I've disassembled a lot of things like my Xbox 360 or a DS Lite, but never an HTC phone.
But I do relate. Using the wrong screwdriver size can really screw you over (pun not intended). I don't have any idea what screws you need, but I can recommend you something else that you might find useful for any future DIY projects.
http://www.ifixit.com/Tools/Pro-Tech-Toolkit/IF145-072
That's the last screwdriver set you'll ever need for breaking into stuff. Just throwing that out there.
Really not all that bad bro, Just be sure to use a credit card or something similar to a pry tool when having to separate plastic hinges.
I lost the bottom left screw and I replaced it with a similar sized screw I had.
I always keep small screws for things like this, in an Altoids tin, perfect size to store random screws.
SirSigma said:
Wow, I've never gone as far as to actually disassemble my HTC phone before. I've disassembled a lot of things like my Xbox 360 or a DS Lite, but never an HTC phone.
But I do relate. Using the wrong screwdriver size can really screw you over (pun not intended). I don't have any idea what screws you need, but I can recommend you something else that you might find useful for any future DIY projects.
http://www.ifixit.com/Tools/Pro-Tech-Toolkit/IF145-072
That's the last screwdriver set you'll ever need for breaking into stuff. Just throwing that out there.
Click to expand...
Click to collapse
I actually had the "proper" TORX driver sent to me with the digitizer, but they must have send a slightly smaller one because it stripped them to ****. I do have a decent toolkit for desktop/laptop repairs, but I messed up on this one. I figured similar phones like the DINC, EVO or Sensation would have the same screws... nope, smaller.
There were some discussions at the old Omate forum, but no confirmation on the actual specification for the back-plate and SIM screws.
As the threads are very easy to wear-out, it is not unreasonable to have to replace them every time opening the cover.
The screws seem to be difficult to find. It may be possible to get them at an Optican. Other than that, they can be ordered from something like aliexpress. The screws are normally in lots of 100 to 1000 pieces. While the cost for each screw is low, Fedex cost many times the package cost. So it is good to have the specifications confirmed early, so China Air Mail can be used.
With dimensions and a supply settled, there may be unofficial "national distribution centers".
I have a de-threaded back-plate screw and have assumed some data below
Dimension: (M1.4)
Pitch: (0.3mm (coarse, 0.2 is fine but unusual)) (There seem to be 9 threads on 3mm, so 0.3mm seem reasonable)
Back Length: 3mm
SIM length: 2 mm
Head size: 2 mm
Holes are about .5mm longer than screws and 2.1mm diameter
Quality: "Soft" (not stainless/titanium, to decrease risk that housing threading is damaged) Nickelplated OK?
I found a couple of suppliers. Those with best fit seem to have 2.5mm head. It should be possible to adjust head and length...
Cost is $6 for 200 pieces, shipping with air-mail about the same.
gerhardo said:
There were some discussions at the old Omate forum, but no confirmation on the actual specification for the back-plate and SIM screws.
As the threads are very easy to wear-out, it is not unreasonable to have to replace them every time opening the cover.
The screws seem to be difficult to find. It may be possible to get them at an Optican. Other than that, they can be ordered from something like aliexpress. The screws are normally in lots of 100 to 1000 pieces. While the cost for each screw is low, Fedex cost many times the package cost. So it is good to have the specifications confirmed early, so China Air Mail can be used.
With dimensions and a supply settled, there may be unofficial "national distribution centers".
I have a de-threaded back-plate screw and have assumed some data below
Dimension: (M1.4)
Pitch: (0.3mm (coarse, 0.2 is fine but unusual)) (There seem to be 9 threads on 3mm, so 0.3mm seem reasonable)
Back Length: 3mm
SIM length: 2 mm
Head size: 2 mm
Holes are about .5mm longer than screws and 2.1mm diameter
Quality: "Soft" (not stainless/titanium, to decrease risk that housing threading is damaged) Nickelplated OK?
I found a couple of suppliers. Those with best fit seem to have 2.5mm head. It should be possible to adjust head and length...
Cost is $6 for 200 pieces, shipping with air-mail about the same.
Click to expand...
Click to collapse
Great info. I am needing some new back plate screws. Would you mind posting the link to the online supplier?
kp12584 said:
Great info. I am needing some new back plate screws. Would you mind posting the link to the online supplier?
Click to expand...
Click to collapse
I do not think xda rules allows posting of direct links.
I got the screws from ebay, seller bohwu, 50 pieces. Fast and cheap.
Just search for "m1.4x4" to find more suppliers.
But it would be interesting f someone finds a good supplier for 2mm heads.
As the heads are not perfectly round after adjusting, it would be good if someone found a supplier.
All sources I found on ebay and those I looked at aliexpress either listed 2.5mm heads or had no size and a picture indicating more than 2mm.
Can you guys confirm the screws the back cover and sim card slot use then? I need to get some spare as you said the heads get easily damaged. I can't even get my backcover off! To prevent damaging the head I've just ordered a proper screw driver as the supplied one is rubbish. Have only managed to take the sim card cover off. The backplate is put on too tight.
Get the back cover off somehow, drilling the heads off the cheap screws it was assembled with if necessary, then replace the screws with the spares that came in the same little bag as the crappy screwdriver-like-object. They are better quality, but be sure you only touch them with a good ph000 driver.
Sent from my Nexus 7 using Tapatalk
I want to install an SD card, but the back plate of the Truesmart... is not possible to remove.
I've used the OEM screwdriver and my own screwdrivers, but I've only managed to undo two screws; the other two are stuck. I think it might be the fact that the grooves of the screws are too flat.
However, does anybody have tips or recommendations to undo these two screws?
There are tiny stickers that say "OK" under a microscope over two of the backplate screws, to prevent tampering and inserting your SD card and having to do warranty replacements. If you didn't remove them first, they are now filling up the inadequate Phillips #000 head slots with plastic sticker.
Throw away the little screwdriver thing it shipped with, unless you need it for stabbing Smurfs.
If you have to drill out the screws, the spare ones shipped with the watch are better quality anyway.
Sent from my Nexus 5 using Tapatalk
Use a better screw driver. I had to use one of my precision screw drivers to get sufficient grip on the screws to unscrew them.
speedyink said:
Use a better screw driver. I had to use one of my precision screw drivers to get sufficient grip on the screws to unscrew them.
Click to expand...
Click to collapse
Be a bit careful, though, because one of my Sim card Compartment screws was way tight and I used a proper screw driver--and the screw sheared leaving about 1 mm stub in the bottom of the screw thread hole--at least, that is what I think must have happened since the screw in question is now about 1 mm shorter than the other.
I have written a nice letter to Omate, and got an initial reply--but, it's anyone's guess what their remedy will be?? Not a replacement watch I am sure.
Drilling and tapping screws that small is not possible--at least not by me.
I ended up having to apply heat to the screws in the sim cover to remove them. Intresting enough, there was no sign of threadlocking agent when the screws finally came out.
What exact kind of Screwdriver do you need?
I have problems with the standard one that came with the TS. No I want to buy a better one from Amazon or hardware-store.
I have the same issue, the screwdriver that came with the TS is pretty much useless. I was able to remove just one screw and the rest did not budge...
I am really disappointed with the design flaws of this device.
Yep, stock screwdriver is a POS.
Sent from my LG-V500 using XDA Free mobile app
The driver I used is marked P0 - and i think it is this:
http://www.amazon.co.uk/Stanley-66-344M-4-in-1-Pocket-Screwdriver/dp/B0014KMDZ0
I think I bought mine in Tesco, it's pretty handy and better quality than I expected.
Here's to hoping someone still checks here and has a spare one to sale. I've dropped my phone a bit too many times and my back cover broke.
It's about $5-10 from ebay, wondering if I could get it slightly cheaper from someone on here. Or even at same price, at least I feel like I know you guys more than random ebay seller
I realize it's been a while since you posted, but you might try using an old soldering iron, and a bit of ABS plastic to weld the cracks up. You could also mix some acetone with ABS plastic bits into a jelly type consistency, then spread it over the cracks...
I'm thinking im going to take the plunge and try and replace the battery in this thing. Battery life is certainly sub par 14 months in with moderate to heavy use. Does anyone have any recommended kits or places to buy the tools needed for the job? I've looked at various tear downs and it doesn't seem terribly hard to do. Is the stuff from iFixit any good?
https://www.amazon.it/gp/aw/d/B01MSZQBLP/ref=yo_ii_img?ie=UTF8&psc=1
I bought this one and seems to have all pieces... A smartphone repair tool kit on Amazon will be ok, they are the same for every smartphone I think
cdgtcc said:
I'm thinking im going to take the plunge and try and replace the battery in this thing. Battery life is certainly sub par 14 months in with moderate to heavy use. Does anyone have any recommended kits or places to buy the tools needed for the job? I've looked at various tear downs and it doesn't seem terribly hard to do. Is the stuff from iFixit any good?
Click to expand...
Click to collapse
The main things you'll need is a small phillips head screwdriver, a precision razor blade, and a heat gun or hair dryer to heat the back. The rest can be done with old gift cards or playing cards. You may also want to order a new back cover with the top and bottom strips if you are picky about small dings. It's difficult to remove the back without leaving small dings at the injection site of the razor blade. Replacement backs are only about $25.
hawkswind1 said:
The main things you'll need is a small phillips head screwdriver, a precision razor blade, and a heat gun or hair dryer to heat the back. The rest can be done with old gift cards or playing cards. You may also want to order a new back cover with the top and bottom strips if you are picky about small dings. It's difficult to remove the back without leaving small dings at the injection site of the razor blade. Replacement backs are only about $25.
Click to expand...
Click to collapse
Thanks - that's not too terrible. Dings I'm not THAT concerned about unless I royally mess this up. For the most part my phone is in a slim rubber case so I'd never see them. I'm still enjoying this phone aside from battery life so definitely looking to expand its life another year at least. Nothing thats out now really meets the quality and features of the 6p for me yet.
blow dryer, hobby blade kit, playing card, phillips screw driver, patience and a brain! its super simple to do... i was sweating up a storm and then realized it wasnt hard at all. the glas on the back panel is harder than you think... and if it breaks they sell aftermarket ones for like 7 bucks.... i
cdgtcc said:
I'm thinking im going to take the plunge and try and replace the battery in this thing. Battery life is certainly sub par 14 months in with moderate to heavy use. Does anyone have any recommended kits or places to buy the tools needed for the job? I've looked at various tear downs and it doesn't seem terribly hard to do. Is the stuff from iFixit any good?
Click to expand...
Click to collapse
This website might help you out.
https://www.etradesupply.com/blog/replace-huawei-nexus-6p-battery-7-steps/
Sweet - thanks everyone for the help. Anyone have any trust worthy battery sources for an OEM battery?
I saw many vdo clips about this many times , but I am not sure about my skill. :fingers-crossed::fingers-crossed::fingers-crossed:
ps000000 said:
I saw many vdo clips about this many times , but I am not sure about my skill. :fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
It's not that hard. You need patience before any tools, mostly to open the camera glass, then it's super easy. And if you crack it, the replacement is going to cost less than 10 bucks, so it's not a big deal, don't worry!
Saw a couple of people used a hair dryer instead of a heat gun. Did it work out ok? Id rather save the $ for a product I likely won't get much use out of. But remember reading elsewhere that a hair dryer is a bad substitute... maybe for this particular job its ok?
Would someone please post source/links for oem replacement parts? Back, glass, bottom piece...
Swapping battery I'm guaranteed to break something.
Tks
Born<ICs said:
Would someone please post source/links for oem replacement parts? Back, glass, bottom piece...
Swapping battery I'm guaranteed to break something.
Tks
Click to expand...
Click to collapse
Some information here