Does anyone have a recommendation of where to find replacement screws for the Rezound? I've tried Amazon, eBay, etc. and no luck. I ended up ordering screws from similar HTC phones, but the screws turned out to be smaller. Just about all of my screws are stripped from using the wrong TORX driver... ended up having to use a screwdriver just to get them out to replace the digitizer. Any help is greatly appreciated.
Wow, I've never gone as far as to actually disassemble my HTC phone before. I've disassembled a lot of things like my Xbox 360 or a DS Lite, but never an HTC phone.
But I do relate. Using the wrong screwdriver size can really screw you over (pun not intended). I don't have any idea what screws you need, but I can recommend you something else that you might find useful for any future DIY projects.
http://www.ifixit.com/Tools/Pro-Tech-Toolkit/IF145-072
That's the last screwdriver set you'll ever need for breaking into stuff. Just throwing that out there.
Really not all that bad bro, Just be sure to use a credit card or something similar to a pry tool when having to separate plastic hinges.
I lost the bottom left screw and I replaced it with a similar sized screw I had.
I always keep small screws for things like this, in an Altoids tin, perfect size to store random screws.
SirSigma said:
Wow, I've never gone as far as to actually disassemble my HTC phone before. I've disassembled a lot of things like my Xbox 360 or a DS Lite, but never an HTC phone.
But I do relate. Using the wrong screwdriver size can really screw you over (pun not intended). I don't have any idea what screws you need, but I can recommend you something else that you might find useful for any future DIY projects.
http://www.ifixit.com/Tools/Pro-Tech-Toolkit/IF145-072
That's the last screwdriver set you'll ever need for breaking into stuff. Just throwing that out there.
Click to expand...
Click to collapse
I actually had the "proper" TORX driver sent to me with the digitizer, but they must have send a slightly smaller one because it stripped them to ****. I do have a decent toolkit for desktop/laptop repairs, but I messed up on this one. I figured similar phones like the DINC, EVO or Sensation would have the same screws... nope, smaller.
Related
Before we were so rudely interrupted in the original thread, we were discussing the G1 hardware keyboard replacements. Please folks, if you must flame each other do it via PMs to avoid locking legitimate threads.
I've been able to find some inexpensive after market replacements on eBay, but still am not sure how difficult it is to actually do that. All the sites I've been able to find on the subject only provide time-lapse dis-assembly instructions of the entire phone. If anyone has done the replacement themselves, I'd greatly appreciate pointers on how to keep my phone operational after I put it back together.
I replaced the white keyboard in my Dream with a black one. It was a scary operation as it takes a bit of force to dismantle. I accidently pulled my antenna off and disconnected a flylead. ment my phone had no signal at all. later when i got home (did it in work ) i took it apart again and fixed it.
Take your time and have patience, alot of it is plastic and clipped together so requires a bit of force.
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
brummiesteven said:
May I ask what is wrong with the keys on the bronze one? I did a quick skim of the old post and gather that you can't see the keys in daylight but I don't get why?
I'm just genuinely interested, I have a black G1 so never had such a problem.
Click to expand...
Click to collapse
It's the combination of silver keys with light-silver backlight that make the lettering almost impossible to see in day light conditions. I'd take a picture if I had a camera with me today. Whoever came up with that color combination should be fired. Or at least made to stare at it every day for the next year. I have to tilt the keyboard at a weird angle just to distinguish the letters. From what I understand the white G1s suffer from the same problem.
The "Backlight Off" app definitely helps as it lets you toggle the backlight with a keyboard shortcut. I'm looking for a more hardware solution though.
I've been thinking about changing keyboards and housings too. But from what ppl are saying it seems to be pretty exhaustive. Do any of you guys have the service manual? I DL'ed it from somewhere and it goes through each step of disassembly and also shows assembly. I'm sure it would help out to give an idea of what you need. But like I said, even having read the service manual, it's still quite scary.
A full housing from my understanding is a bitc(....doing the KB I can see why. The LCD portions look ridiculously complex in comparison to other phones.
That said if you have the proper tools , good organization or memory , steady hands and patience really shouldnt be "that" tough to do the keyboard.
Heres the thing. Its really not that hard to unscrew things etc...but the piece you need to move in order to get proper access to the KB has 2 ribbons that are a PAIN IN THE ASS to take off and put back properly. Theres so little room for error.If youve never worked with ribbons before BE CAREFUL.
I will say G1 is pretty unique in how its put together , I swear they were determined to make it as complicated as possible
The really pain in the ass part is that the online manual/guide will merely tell you something like "remove part A" but no explanation how. Theres also 2 screws I swear it glossed over leading to frustration when I did the trackball/front keys.
Torx 5 and really good mini screw driver are mandatory.
Nice lil workstation is really helpful..(masking tape ,towel , table lamp or LED headlamp , vitamin/pill cases etc)
Im no mechanical engineer but Ive opened up damn near everything Ive ever owned at some point. Took me a solid 3 hours from start to finish. With major time spent on organizing the screws pieces and those damn ribbons.
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
KOF33 said:
I will say the black KB makes a HUGE difference. Black key on the front arent necessary but do look better and add much needed contrast.
Click to expand...
Click to collapse
Pics, or it didn't happen
Thanks for the tips!
Chahk said:
Pics, or it didn't happen
Thanks for the tips!
Click to expand...
Click to collapse
As you can see I also replaced the trackball with a glowing white one.
lol at the trackball
doing a case swap is only bad the first time LMAO. I learned a lot, like for example the brass inserts that the screws go into...are not pre-installed. You must CUT Them out of the old housing and HAMMER them into the new oneBut in the end, it turned out very nice.
As far as just replacing the keyboard, it isnt too bad actually once you know what screws hold what down!
-Remove the 6 torx screws for the back housing
-GENTLY pry open the TOP of the casing with a plastic case tool, work your way down to the bottom of the housing. The bottom is a PITA to remove. I usually get it by rocking it gently back and forth
-remove the long and short coax leads from the motherboard side. swing them out of the way
-peel back the tape and GENTLY pull the bottom connector (mouthpiece module) from the motherboard.
-peel back more tape and lift the latch for the keyboard connector (the one on the side)
-Peel the camera module up SLOWLY (it is double side taped down) as well as the imei card. The cam cable is routed under it, lift it all as a unit. When you get to the motherboard, STOP
-Now, gently twist the whole camera and motherboard unit as a whole until it is free of the latch on the side. Gently lift the camera end exposing the 2 small ribbon connectors on the bottom.
-Peel back the tape and GENTLY lift the ribbon connectors out of the board. Place the motherboard/camera unit to the side for now.
-Remove all the black and silver screws for the metal piece. The lcd should stay in place as the mouthpiece plastics kinda hold it for you, but you should still support it to keep from hurting the connections.
-Viola, keyboard access. Remember when you put it back together be sure to re-tape all the connections, else when you drop your phone one of them may pop loose.
Keeping the motherboard and camera/imea plate all as one module saves you from a very difficult connection and will help you keep everything aligned when reassembling it.
I guess the spacebar has 2 functioning buttons, (left and right) ... well my right side just konked on me, and i was wondering if a replacement keyboard off ebay will fix this, or are they just the button "covers"?
the "buttons" are just plastic nubs that make contact on a board behind it. That board would be what you need. I dont know if there are any on eBay, but I have a spare one if you want to PM me for details.
I dropped my G1 about 6 months ago and was devastated. After entirely too much research I finally got the guts to purchase a replacement digitizer and managed to install it successfully. However, in the process I managed to rip the LCD ribbon cable. I then had to order a replacement LCD screen. I've also damaged one of the black ribbon cables pretty severely causing the touchscreen to become unresponsive sporadically. I've just placed an order for one of those ribbon cables and will hopefully have that up and running soon. I've also purchased an entire new housing unit to rebuild the phone to make it look as new.
Now when I first took this thing apart I was by NO MEANS an expert or have ever done something like this before. I'm just an avid enthusiast who wanted to save a little money, feel a sense of accomplishment and to learn a few things along the way. I technically paid nearly the same amount of money it would have cost me to send the unit to HTC for repair, however i've learned everything there is to know about my phone's hardware. I know which board does what and are extremely confident about fixing ANY hardware problem in the future.
If you have the time, patience, and truly want to become confident about the workings of your phone, then I highly recommend fixing it yourself. I've bought my parts for VERY cheap off of reputable ebay buyers. You can find EVERY single piece for your phone on Ebay. My LCD has 1 dead pixel, but I guess that's the risk you take when you buy really cheap parts.
Hope this helps.
So I managed to shatter the glass on my rezound....go me. I was wondering if anybody here has replaced the screen on the rezound and how hard it is to do. I didn't find a lot of rezound tear down info out there. I do a lot of laptop work and it seems like simular construction techniques. the only thing that has me a bit concerned is the whole adhesive issue. Using a heat gun to get the old screen off and I guess the new one will either adhere to the old adhesive or I need to find a source??
Anyway they appear to be 50 dollars for the part versus 100-150 to send the phone off to have someone else do it. Any thoughts???
While I haven't done the rezound yet, I have done a few others, the most recent being a Droid X. I ordered the 'official' advesive on the first phone screen repair I did but never again. It was hard to deal with...if you don't get it right perfectly the first time... you're done. I went with a 3M double sided foam tape after that and was SO much easir to deal with. Never had a screen pop off and anything like that. My wife is still using that phone as we speak.
Next biggest thing to watch out for is tearing those damn thin cables.... they tear so easy...seriously, do not use any sort of tension on those cables. One little tear could out your camera, or soft keys... or even portions of your digitizer. Such a pain in the ass.
Take care while dis & re assemb ling it, you should be fine. It's a lot more delicate than a laptop, so be careful.
I have never replaced the screen on my Rezound, but I have done a few other phones. My wife dropped her Dinc and broke the screen, then the digitizer went out on my OG DROID. If the Rezound is built like the Dinc then you will be golden. Took only about 20 minutes. But as stated above you MUST be very careful when disassembling the phone. The micro ribbons are a little forgiving but are pretty delicate.
Good luck though and let us know how it works out for you.
Sent from my ADR6425LVW using xda premium
Well I opted to get it replaced mainly because I found a local place that could do it and had the part in stock. However the one they installed has clear buttons instead of red, which I like more but I think its best to stay with the way it is suppose to look. Also there is a small black line that they think might be a smug. They are looking for a screen with the factory red buttons. The question I have is I noticed this digitizer registers 4 points and I thought the rezound did 5 can someone verify how many points of touch its suppose to recognize?
kappen said:
Well I opted to get it replaced mainly because I found a local place that could do it and had the part in stock. However the one they installed has clear buttons instead of red, which I like more but I think its best to stay with the way it is suppose to look. Also there is a small black line that they think might be a smug. They are looking for a screen with the factory red buttons. The question I have is I noticed this digitizer registers 4 points and I thought the rezound did 5 can someone verify how many points of touch its suppose to recognize?
Click to expand...
Click to collapse
My rezound i got from verizon refurb only has 4 input.
my rezound has always only had 4 points
Thanks for the replies.
Hey guys -
Figured I'd throw this out there. Is anyone aware of a 3D model of the design of the LGOG? Not necessarily the whole thing but the back cover would suffice. I've got a buddy who has a business in which he makes custom metal parts. He's not precision machines that, if I supply the autoCAD or 3D model, they can laser cut it out of a nice piece of aluminum or whatever. Errr, how dope would that be??
I know I'd need to move the antenna and NFC, but that shouldn't be too difficult.
If this works out I can possibly run a batch for some of you other owners that are interested out there!
Let's do some digging!
Doubt anybody has it. Your friend doesn't have some sort of 3d scanner?
piotrus22 said:
Hey guys -
Figured I'd throw this out there. Is anyone aware of a 3D model of the design of the LGOG? Not necessarily the whole thing but the back cover would suffice. I've got a buddy who has a business in which he makes custom metal parts. He's not precision machines that, if I supply the autoCAD or 3D model, they can laser cut it out of a nice piece of aluminum or whatever. Errr, how dope would that be??
I know I'd need to move the antenna and NFC, but that shouldn't be too difficult.
If this works out I can possibly run a batch for some of you other owners that are interested out there!
Let's do some digging!
Click to expand...
Click to collapse
I really wish I could help, what you're proposing sounds awesome, however;
I would get an aluminum blank and (tape?) it to the back of the phone or at least hold it there and observe your wireless functionality.
Make absolutely sure that your cell/wifi/bluetooth still works with a metal plate there.
If you can do me a favor, please post the results, and try copper as well if it's available. I'm interested in internally placing a copper or aluminum shim for extra thermal mass and heat spreading. This would be very useful to know.
If I come across anything I'll pass it your way, in the meantime you might want to make a cast of it for your friend with a clay mold or plaster of paris, etc.
That process itself might actually be a usable solution and net you a custom back piece, make a cast copy and use say fiberglass, then you can coat it with a carbon fiber decal or something, would look pretty awesome
http://www.ehow.com/how_5977827_cast-craft-molds.html
plenty of casting / mold making guides on the web. the only extra steps I would take would be to fill the screw holes with a dab of clay on the underside of the back piece so that it can be removed easily from the mold, you'll just have to poke them out of your copy when you're done.
I want to install an SD card, but the back plate of the Truesmart... is not possible to remove.
I've used the OEM screwdriver and my own screwdrivers, but I've only managed to undo two screws; the other two are stuck. I think it might be the fact that the grooves of the screws are too flat.
However, does anybody have tips or recommendations to undo these two screws?
There are tiny stickers that say "OK" under a microscope over two of the backplate screws, to prevent tampering and inserting your SD card and having to do warranty replacements. If you didn't remove them first, they are now filling up the inadequate Phillips #000 head slots with plastic sticker.
Throw away the little screwdriver thing it shipped with, unless you need it for stabbing Smurfs.
If you have to drill out the screws, the spare ones shipped with the watch are better quality anyway.
Sent from my Nexus 5 using Tapatalk
Use a better screw driver. I had to use one of my precision screw drivers to get sufficient grip on the screws to unscrew them.
speedyink said:
Use a better screw driver. I had to use one of my precision screw drivers to get sufficient grip on the screws to unscrew them.
Click to expand...
Click to collapse
Be a bit careful, though, because one of my Sim card Compartment screws was way tight and I used a proper screw driver--and the screw sheared leaving about 1 mm stub in the bottom of the screw thread hole--at least, that is what I think must have happened since the screw in question is now about 1 mm shorter than the other.
I have written a nice letter to Omate, and got an initial reply--but, it's anyone's guess what their remedy will be?? Not a replacement watch I am sure.
Drilling and tapping screws that small is not possible--at least not by me.
I ended up having to apply heat to the screws in the sim cover to remove them. Intresting enough, there was no sign of threadlocking agent when the screws finally came out.
What exact kind of Screwdriver do you need?
I have problems with the standard one that came with the TS. No I want to buy a better one from Amazon or hardware-store.
I have the same issue, the screwdriver that came with the TS is pretty much useless. I was able to remove just one screw and the rest did not budge...
I am really disappointed with the design flaws of this device.
Yep, stock screwdriver is a POS.
Sent from my LG-V500 using XDA Free mobile app
The driver I used is marked P0 - and i think it is this:
http://www.amazon.co.uk/Stanley-66-344M-4-in-1-Pocket-Screwdriver/dp/B0014KMDZ0
I think I bought mine in Tesco, it's pretty handy and better quality than I expected.
Yep. Kid got a hold of it before case arrived. Yes its my fault. Should have kept better eye on him. There are only two bids on YouTube. Neither one is great. I see on eBay they have LCD and digitizer and housing. From vids it looks easy. But would like to hear from anyone who has done it. Thanks
So sorry for the breakage. Here is a video that seems pretty good, https://www.youtube.com/watch?v=qm6NwBvo6T0. The process doesn't seem to hard, to me. Good luck.
kimtyson said:
So sorry for the breakage. Here is a video that seems pretty good, https://www.youtube.com/watch?v=qm6NwBvo6T0. The process doesn't seem to hard, to me. Good luck.
Click to expand...
Click to collapse
I recently replaced the LCD screen on a OnePlus One, other than the size, it was almost identical to the Mate2. couple parts in different spots but it had enough of those #%(@!)% rice grain size screws that I put them on a magnet, to make sure I didn't lose them.
Yes. That is one of the vids I was talking about. The other one was actually for a mate. Not mate 2. The thing I don't understand on this video is he never actually gets to the part of the screen replacement. So, I am presuming that with this phone as long as I purchase the LCD+digitizer+frame. Then it will just be a matter of putting all the parts including board back in to it. On eBay there are choices. You can purchase just the glass or glass and digitizer or those plus what they call the frame. While on my phone. Only the outside glass is broken. I am going to buy the kit that has all three. I would give just replacing the glass a shot if I could find a video or tutorial. I have looked everywhere. Nothing. The closest thing I could find is the vid on youtube of the guy changing just the glass on his mate. Unfortunately, he never says a word in that vid. I guess it's just to show it can be done. I'm really stressed by all this. I would prefer to just change the glass if only I could find some info. I presume it is like a Samsung where glass is glued with local to digitizer. I have fixed those type on a s3 and note 2. Was not that hard. Just be sure to heat properly and don't scratch digitizer. With no idea of how it is done on this phone. I guess I will get the kit and hope for the best as of course. It has to come from China. Waiting....Thanks for the info and I will do my best to make a vid so others can learn from my mistakes? Lol or hopefully success.
Have a hair dryer or a heat gun handy just in case. On the OnePlus, the screen is "glued" somewhat, to the plastic frame. It is a LOT easier to separate if you heat is up a
bit. Just heat one side, then you the (as I like to call it) guitar pick tool to start to pry it up, then to a little more at a time, so you don't overheat the broken screen.
After you get the screen off, make sure you scrape around the edges of the frame, to ensure you remove any sticky residue. You don't need to heat up the new screen. Once you press it down, it will stick quite well.
If it were me I would get the entire kit and be done with it. There is too much that can go wrong with the hairdryer and peeling the old, broken screen from the digitizer. With the kit, it's just all screws and dismantling then put it back together. Much easier.
I hope that is right about the kit. The thing that scares me is what will the quality of the parts be like? I know my digitizer is fine. So I'm going to try the kit first. If it fails due to bad parts. Then I will still have the option of just doing the glass. The cheapest I saw for the glass was 18.00 bucks. The kit with shipping was 58.00....Not really a huge difference. Again its the quality of the parts that scares me. Of course the vid on youtube makes it look easy. But I'm sure he is doing it on a phone that has been torn down a few times. Its always easier then. As I said. I intend to video all this. If nothing else. There will at least be more info available to poor suckers like me..lol. Will see in a couple weeks if the Chinese ship time holds true...
I'd bet the quality is the same as OEM.
Sent from my MT2L03 using XDA Free mobile app
One other thing. Just wanted to ask. You say the one plus is about the same? Are you saying that because there similar in how their made? Or do you know something about where their made. Thanks for the info on the glass. I have done it on Sammy phones. Has to be similar. Kit is already coming. So I'll go that route first try. Wish your repair had been on a ham2. Then I would feel better. I guess I get to go first. Lol
kimtyson said:
I'd bet the quality is the same as OEM.
Sent from my MT2L03 using XDA Free mobile app
Click to expand...
Click to collapse
The one I ordered for the OPO looked identical, except the routing for the lcd screen connector was just a little different, but in no way caused a problem.
I wanted to update you guys on how the repair of my screen is going. I have some info to share and trust me. It is important if you ever need to DIY on this phone. Most are aware of the video on youtube. Ive watched it several times and I always got the feeeling it looked to easy. Well, my screen and dig assy came in today. I was going through the process of tearing it down and everything was going well. Untill i got to the part where you remove the power button cable. The one that runs along the side of the phone. I SHOULD HAVE KNOWEN. In his vid. He makes it look like this cable will come off with gentle pressue. BULL****. It wont. It is glued Tight and you will just winde up tearing it. I am so pissed. I wish he would have just said to buy the cable with the kit. Its 10 bucks on ebay of course. So, now I have a torn down phone waiting for the cable. I was making a video of the repair. When the cable comes in. I will finish it and upload to youtube. The other thing he makes look easy is the removal of battery. Again, its not and you could damage it too. But I managed not to. Anyway i am really upset right now so sorry for cussing. I want to find that dude and shake his hand and smack him at same time...
pckarma112 said:
I wanted to update you guys on how the repair of my screen is going. I have some info to share and trust me. It is important if you ever need to DIY on this phone. Most are aware of the video on youtube. Ive watched it several times and I always got the feeeling it looked to easy. Well, my screen and dig assy came in today. I was going through the process of tearing it down and everything was going well. Untill i got to the part where you remove the power button cable. The one that runs along the side of the phone. I SHOULD HAVE KNOWEN. In his vid. He makes it look like this cable will come off with gentle pressue. BULL****. It wont. It is glued Tight and you will just winde up tearing it. I am so pissed. I wish he would have just said to buy the cable with the kit. Its 10 bucks on ebay of course. So, now I have a torn down phone waiting for the cable. I was making a video of the repair. When the cable comes in. I will finish it and upload to youtube. The other thing he makes look easy is the removal of battery. Again, its not and you could damage it too. But I managed not to. Anyway i am really upset right now so sorry for cussing. I want to find that dude and shake his hand and smack him at same time...
Click to expand...
Click to collapse
I have worked on several phones. None are easy really. Most all companies use some type of adhesives. Alot glue the batteries in as well. Dunno if you tried it but heat seems to help with the glue. Seen a guy do it with a hair dryer. Worked for me as well with a screen replacement. Never took one of these apart so I have no idea if they use heat activated glue or not. Good luck!
Well Thanks for reply. I too have fixed a few. As long as I have something to guide me. Im Cool. Vid or written indtructions. Yes all phones use some sort of glue. With this one on the cable. Heat would not have helped. You would just melt the cable. I was expecting some adhesive. But not like this. This was not meant to be reused. Period. Thats my point. I wish he would just have said buy the cable. No way it is coming off in one pc. The speaker is also glued down extremely tight. I think I got it. Its still in one pc. Interesting enough. There also on ebay.
I really just want people to know about the power cable. If you have to replace screen on this phone. Get one. Your gona need it. Now it may be middle of july by the time I get the cable. I went ahead and tore everything else out of phone. Tomorrow I will put all back into new assy. But i wont know if it worked till cable gets here. I forgot to record taking out the other pcs. I was just to stressed. But I do have some good vid for most of it. Gripe is now over. il be back when cable gets in...
pckarma112 said:
Well Thanks for reply. I too have fixed a few. As long as I have something to guide me. Im Cool. Vid or written indtructions. Yes all phones use some sort of glue. With this one on the cable. Heat would not have helped. You would just melt the cable. I was expecting some adhesive. But not like this. This was not meant to be reused. Period. Thats my point. I wish he would just have said buy the cable. No way it is coming off in one pc. The speaker is also glued down extremely tight. I think I got it. Its still in one pc. Interesting enough. There also on ebay.
I really just want people to know about the power cable. If you have to replace screen on this phone. Get one. Your gona need it. Now it may be middle of july by the time I get the cable. I went ahead and tore everything else out of phone. Tomorrow I will put all back into new assy. But i wont know if it worked till cable gets here. I forgot to record taking out the other pcs. I was just to stressed. But I do have some good vid for most of it. Gripe is now over. il be back when cable gets in...
Click to expand...
Click to collapse
With any luck you may save someone else a headache!
pckarma112, so sorry for your frustration. Thanks for sharing your experience.
I was going to suggest the the same thing as Moody. Heat from a hair dryer usually helps soften the glue but isn't enough to destroy anything (usually).
Just so we are all understanding, can you show a pic or provide a link of what you purchased? Was it just a screen or an assembly?
Again, sorry for your issues. Hang in there.
Parts
Yes I can. That is if I can post links. So Il try. This is the link for the power cable: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItemVersion&item=291410104104&view=all&tid=1181571120019 This I just ordered yesterday. The deleivery is anywhere from middle of July to second week of August. Im keeping my fingers crossed that I got a good vender and will get a good one. They say they have already shipped it and gave me a tracking number. But the number is not showing up yet. Ive seen this before with china stuff. I will give it a couple days and check again.>... The next one is for the screen kit: http://www.ebay.com/itm/141653108269?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT > Cant say enough good things about this vendor and kit. It looks and feels outstanding and I recieved it in two weeks from china. That is pretty darn good. Now, the only thing is since I have no power cable. I do not know for sure if I got a good one. But, like I said. It feels like a quality part. The last item is a phone repair kit that really helped with this job. The metal and plastic spudger really helped with battery and other small parts like camera and vibrator. For the price I suggest you get one. Here it is: http://www.ebay.com/itm/111501320079?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT
As for the screw driver. Dont do what i did. I bought a cheapo 1.69$ one. It was crap. Lucky for me. I had one from a previous kit I bought and it worked fine. Hopefully these links will show up for you guys. If not I will try with a different browser.
Just so its clear. I do have a hair dryer that I keep for samsung screens. I thought about trying it on the cable. But I have worked on these kind before. There is a really fine line between warming the glue and melting the cable. This sucker had enough glue to hold the hoover damn together. Ive seen it before and Im pretty sure you would melt cable before the glue would give away. Thanks you guys for advise and just letting me vent. I do hope that anyone who attemps a repair can learn from my mistakes....lol. Thanks again.
I've been taking stuff apart and SOMETIMES successfully getting it back together for over 40 years, sometimes with the odd screw leftover, but hey, where do our extra screws come from eh?
I replaced the screen on the OnePlus for a friend a couple months ago and WOW, they need to make these screws JUST a LITTLE smaller, don't you think? I find that keeping a small magnet on hand comes in handy to keep track of those tiny a** screws.
pckarma112- Nice job on the post of Parts. Only problem is the first link failed. Said it was too old. Again, thanks for sharing and letting us learn from your mistakes.
Thanks for the *cough* compliments. The link is bad because seller is sold out. However, you can try this one:http://www.ebay.com/itm/111501320079?_trksid=p2060353.m2749.l2649&ssPageName=STRK:MEBIDX:IT......If that does not work then there is this:http://www.ebay.com/itm/Black-LCD-D...412?pt=LH_DefaultDomain_0&hash=item3f3f160554 This is same only black. Again, these people really treated me well. Im sure there will be new auctions when he restocks. There are also plenty of others. Price varies a little. Im really delighted that you find small screws to be a pita. Thats just awsome. lol Keeping a piece of tape on the table really helps. Just drop them on to the tape and I promise you will never lose another one. I would really like for this thread to be helpful to anyone that gets unlucky. So, I am trying to be ernest about it all. That includes honesty with no hidden attitude. When I say thanks. I really mean it.
By the time and god willing the power cable arrives. I will hit the big 60. This will not be the last phone I ever repair( I hope). But it sure has been one of the most interesting. Thanks again guys and may your screws never be loose.
Thanks
p51d007 said:
I've been taking stuff apart and SOMETIMES successfully getting it back together for over 40 years, sometimes with the odd screw leftover, but hey, where do our extra screws come from eh?
I replaced the screen on the OnePlus for a friend a couple months ago and WOW, they need to make these screws JUST a LITTLE smaller, don't you think? I find that keeping a small magnet on hand comes in handy to keep track of those tiny a** screws.
Click to expand...
Click to collapse
Thank you. You gave me a good laugh and it was much needed today. In fact. Its needed everyday in this world. The kit of screw drivers that I own are indeed magnetized. Thank God. Seriously though. If you think these are small. Try repairing a watch. Now your talking micro. I have worked on about a dozen or so with my brother. He is a master clocksman. Makes good money still and when ever he needs help. I get to learn from him and make a little too. So, Im blessed. I also lost track of where a couple screws will go on this phone. But, got it figured out. It is nice to know that none of us are perfect. Thanks again bro.