Hi , so i bought a Stratos 3 China version (A1928) and was on 4.0.19.5 version and did a trial run with it and the gps was working well. However, after updating to 4.2.6.0 and flashing it with the stock US rom , the searching of GPS was prompt with the error " No gps signal detected , please try again outdoors" . After searching the forum , i tried downgrading to 4.2.5.0 and it still doesn't seems to work. Any solution to work around it ?
Gps problem 4.2.7.0
I have the same GPS problem out I am in 4.2.7.0 and the data is random. I did your running and hiking.
I am a little disgusted by the oit saying given GPS at the top with the Stratos 3 and there disaster
The last time I had GPS localisation failure I've reboot the watch a all was working well after that. But I stay in 4.2.5.0 ftm
winni21 said:
The last time I had GPS localisation failure I've reboot the watch a all was working well after that. But I stay in 4.2.5.0 ftm
Click to expand...
Click to collapse
I reset the watch and it remains in 4.2.7.0, how to put in 4.2.5.0 and necessarily forgot the warranty, my stratos is 2 weeks old
bartnissa said:
I reset the watch and it remains in 4.2.7.0, how to put in 4.2.5.0 and necessarily forgot the warranty, my stratos is 2 weeks old
Click to expand...
Click to collapse
You need to unlock bootloader first then use this thread:
https://forum.xda-developers.com/smartwatch/amazfit/fw-tool-stock-global-international-t4031153
(Check previous version section) don't forget to factory reset the watch after flashing the fw.
winni21 said:
You need to unlock bootloader first then use this thread:
https://forum.xda-developers.com/smartwatch/amazfit/fw-tool-stock-global-international-t4031153
(Check previous version section) don't forget to factory reset the watch after flashing the fw.
Click to expand...
Click to collapse
winni 21 if I understood correctly I downloaded Install, that is to say this firmware 'Stratos3_Stock_US_4.2.5.0_Firmware.zip'
and I run with the watch connected to the pc and let it be ?
my model is the A1929 US
bartnissa said:
winni 21 if I understood correctly I downloaded Install, that is to say this firmware 'Stratos3_Stock_US_4.2.5.0_Firmware.zip'
and I run with the watch connected to the pc and let it be ?
my model is the A1929 US
Click to expand...
Click to collapse
If you have your bootloader unlocked yes that's it.
When it's done don't forget to factory reset the watch
winni21 said:
If you have your bootloader unlocked yes that's it.
When it's done don't forget to factory reset the watch
Click to expand...
Click to collapse
I don't know if it's a bootloader and I'm afraid of blocking my watch.
I do not see a simple tutorial for beginners how to install etc ...
thank you
bartnissa said:
I don't know if it's a bootloader and I'm afraid of blocking my watch.
I do not see a simple tutorial for beginners how to install etc ...
thank you
Click to expand...
Click to collapse
here is what I did, install adb setup and then as on the cmd adb devices image, it's ok that means I have the bootloader ???? :confus:
how to reset my watch connected with the computer or the button on the watch to disconnect to the computer.
if I reset the factory settings, it will come back to 4.2.7.0 ?
thanks
bartnissa said:
here is what I did, install adb setup and then as on the cmd adb devices image, it's ok that means I have the bootloader ???? :confus:
how to reset my watch connected with the computer or the button on the watch to disconnect to the computer.
if I reset the factory settings, it will come back to 4.2.7.0 ?
thanks
Click to expand...
Click to collapse
use this thread to unlock bootloader:
https://forum.xda-developers.com/smartwatch/amazfit/tutorial-unlock-bootloader-warning-void-t3654011
then you'll be able to flash 4.2.5.0 FW. if you factory reset the watch after you'll be still in 4.2.5.0 (do it from the menu off the watch or when it's booted and connected to the computer: adb reboot wipe)
winni21 said:
use this thread to unlock bootloader:
https://forum.xda-developers.com/smartwatch/amazfit/tutorial-unlock-bootloader-warning-void-t3654011
then you'll be able to flash 4.2.5.0 FW. if you factory reset the watch after you'll be still in 4.2.5.0 (do it from the menu off the watch or when it's booted and connected to the computer: adb reboot wipe)
Click to expand...
Click to collapse
sorry winni21, then the fastboot a priori was made image attached. the watch has restarted and I am still in 4.2.7.0 is that normal?
now to put the rom, how do I do?
winni21 said:
use this thread to unlock bootloader:
https://forum.xda-developers.com/smartwatch/amazfit/tutorial-unlock-bootloader-warning-void-t3654011
then you'll be able to flash 4.2.5.0 FW. if you factory reset the watch after you'll be still in 4.2.5.0 (do it from the menu off the watch or when it's booted and connected to the computer: adb reboot wipe)
Click to expand...
Click to collapse
sorry winni21, then the fastboot a priori was made image attached. the watch has restarted and I am still in 4.2.7.0 is that normal?
now to put the rom, how do I do? unlocked yes
what is the simple procedure once download please
Stratos3_Stock_US_4.2.5.0_Firmware
bartnissa said:
sorry winni21, then the fastboot a priori was made image attached. the watch has restarted and I am still in 4.2.7.0 is that normal?
now to put the rom, how do I do? unlocked yes
what is the simple procedure once download please
Stratos3_Stock_US_4.2.5.0_Firmware
Click to expand...
Click to collapse
ok so unzip Stratos3_Stock_US_4.2.5.0_Firmware.zip then run flash_US.bat wait process to be done.
once watch is rebooted wipe it
bartnissa said:
sorry winni21, then the fastboot a priori was made image attached. the watch has restarted and I am still in 4.2.7.0 is that normal?
now to put the rom, how do I do? unlocked yes
what is the simple procedure once download please
Stratos3_Stock_US_4.2.5.0_Firmware
Click to expand...
Click to collapse
watch hangs on screen no command with triangle exclamation mark.
I am disgusted
on which stage it has stopped? reboot your computer and whatch then launch only the flash_us.bat (you can not have 2 adp session at the same time)
winni21 said:
on which stage it has stopped? reboot your computer and whatch then launch only the flash_us.bat (you can not have 2 adp session at the same time)
Click to expand...
Click to collapse
I'm here on my watch!
I have to re-install adb?
STAGE 7 OU 8
it is not in fastboot reboot the watch and try again
winni21 said:
on which stage it has stopped? Reboot your computer and whatch then launch only the flash_us.bat (you can not have 2 adp session at the same time)
Click to expand...
Click to collapse
the watch is not recognized usb/pc
bartnissa said:
the watch is not recognized usb/pc
Click to expand...
Click to collapse
the execution waiting for the watch but it is not recognized
winni21 said:
it is not in fastboot reboot the watch and try again
Click to expand...
Click to collapse
if I restart the monr here is triangleleurs:leurs:
Related
Hi guys,
Here I have Amazfit Bip wich I cant connect to phone because when it asks to confirm pairing I cannot click on YES on the screen.
Any idea what should I have to do?
Thank you!
Hello, today I had the same problem. After installing some firmwares the screen doe not recognize any touch.
I think it is a fault happening while installing the firmware.
First i went back to the original chinese rom and the upgraded to the actual via ADB.
Aft that, everyting is fine again.
By the way. Are you too have the problem with lagging stepcount?
skylow said:
Hello, today I had the same problem. After installing some firmwares the screen doe not recognize any touch.
I think it is a fault happening while installing the firmware.
First i went back to the original chinese rom and the upgraded to the actual via ADB.
Aft that, everyting is fine again.
By the way. Are you too have the problem with lagging stepcount?
Click to expand...
Click to collapse
Hi mate,
Yes I had issue with stepcount.
But can you tell me how could I repair the watch as I cant pair it with the smartphone?
Thanks!
masterross said:
Hi mate,
Yes I had issue with stepcount.
But can you tell me how could I repair the watch as I cant pair it with the smartphone?
Thanks!
Click to expand...
Click to collapse
In my case i flashed "huangeheUS-1.3.3a-installer". Then deleted all the installation trash.
I did a full wipe:
adb shell reboot bootloader
fastboot erase data
fastboot erase cache
fastboot reboot
After that the screen was working again but the watch was in Chinese language.
So i flashed "Stratos_Stock_US_Firmware_2.3.5.0". Now everything is working and in English language.
Thx, but your watch is AmazFit PACE and mine is AmazFit BIP wich doesnt have usb interface unfortunately
masterross said:
Thx, but your watch is AmazFit PACE and mine is AmazFit BIP wich doesnt have usb interface unfortunately
Click to expand...
Click to collapse
Oh, i thought that the Bip has the same interface. Sorry.
Guys,
I opened the watch and cant see anything wrong.
I de-attach and attach battery, clean everything but still touch not works.
good night. it happened today that my xz1 crashed and rebooted, and since then it restarts, and I did not want to format it, because it has important videos that were not saved in the backup, and it also seems that the storage was exhausted, it would be possible to use adb to delete photos of the device with it in that state of loop restarting, going to the tool icon and restarting again ..
I tried to repair it by Xperia companion and it did not work, it keeps restarting in an infinite loop
Ok.. Try this download Xperia firm, and download the software for your region, then flash it with Newflash, ( https://www.google.com/amp/s/forum....newflasher-xperia-command-line-t3619426/amp/) read it first before you do anything..
lilbrat said:
Ok.. Try this download Xperia firm, and download the software for your region, then flash it with Newflash, ( https://www.google.com/amp/s/forum....newflasher-xperia-command-line-t3619426/amp/) read it first before you do anything..
Click to expand...
Click to collapse
Be warned though that NewFlasher wipes all the precious videos if you do not delete the to be flashed file (userdata.sin) for the data partion.
@Alex Rander
What I have done in such cases:
- Reset the phone (won't cure your boot loops)
- start it in fastboot mode
- fastboot boot twrp.img (OOPS - needs unlocked BL)
- then adb pull your data
- then set up new like librat recommends
DHGE said:
Be warned though that NewFlasher wipes all the precious videos if you do not delete the to be flashed file (userdata.sin) for the data partion.
@Alex Rander
What I have done in such cases:
- Reset the phone (won't cure your boot loops)
- start it in fastboot mode
- fastboot boot twrp.img (OOPS - needs unlocked BL)
- then adb pull your data
- then set up new like librat recommends
Click to expand...
Click to collapse
What you said is correct, but if he would have succeeded with Sony companion he have lost the videos anyways... If he unlocks his bl it will reset.. As he didn't mention whether or not he was rooted.. But if he was he could possibly enter twrp, advance, file manager and possibly move his files to an SD card..
my xz1 never moved on it with adb or anything, only thing I did was update it via flashtool, and probably by the xperia companion, I just sent it to the technical assistance, is it possible for them to fix or will have to send a new one?
Alex Rander said:
my xz1 never moved on it with adb or anything, only thing I did was update it via flashtool, and probably by the xperia companion, I just sent it to the technical assistance, is it possible for them to fix or will have to send a new one?
Click to expand...
Click to collapse
So why didn't you try using newflasher?
lilbrat said:
So why didn't you try using newflasher?
Click to expand...
Click to collapse
I tried using newflasher 3 times, but it was unsuccessful, twice with the same rom, and another with the rom of my country, it still did not work.
please someone help me please my verge is bootlooping when i tried to install amazmod using pc after than the watch stopped responding and gets black and it is not rooted and the bootloader is locked i have tried many things non of them are working for me, there is no good source for verge i could find
if anyoune knows something about this please can help me?
xxxanmol said:
please someone help me please my verge is bootlooping when i tried to install amazmod using pc after than the watch stopped responding and gets black and it is not rooted and the bootloader is locked i have tried many things non of them are working for me, there is no good source for verge i could find
if anyoune knows something about this please can help me?
Click to expand...
Click to collapse
Uninstall it, and as a last chance, factory reset your watch using adb reboot wipe command. Another way, If the watch still connects to Amazfit app, unpair the watch while Bluetooth is connected, this will factory reset the watch too.
i solved it finally
Saratoga79 said:
Uninstall it, and as a last chance, factory reset your watch using adb reboot wipe command. Another way, If the watch still connects to Amazfit app, unpair the watch while Bluetooth is connected, this will factory reset the watch too.
Click to expand...
Click to collapse
the issue was with the drivers, i tried it on windows 10 and using all in one tools, installed twrp recovery then flash the rom through STOCK FIRMWARE INSTALLER it really was hard for me to do as lack of drivers and non detecting issues with windows 7 but windows 10 solved it at all finally
overall dont mess with an unrooted, locked bootloader watch or mobile
peace
xxxanmol said:
the issue was with the drivers, i tried it on windows 10 and using all in one tools, installed twrp recovery then flash the rom through STOCK FIRMWARE INSTALLER it really was hard for me to do as lack of drivers and non detecting issues with windows 7 but windows 10 solved it at all finally
overall dont mess with an unrooted, locked bootloader watch or mobile
peace
Click to expand...
Click to collapse
same in here... Amazfit Verge
When I run the command .. it doesn't start in fastboot
kyawzinooygn said:
same in here... Amazfit Verge
Click to expand...
Click to collapse
When I run the command adb shell reboot bootloader, it doesn't start in fastboot. How they solved it?
Can some one help me. I have used "All in one tool" and uninstalled some apks.. Seems they are important apps. Watch is now struck in boot loop that comes after amazfit A symbol. Using the all in one tool, I can again go to this fastboot mode as shown in screenshot. Not sure how to reinstall the uninstalled apks. I am not tech savvy. Can some one help me step by step
xxxanmol said:
i solved it finally
the issue was with the drivers, i tried it on windows 10 and using all in one tools, installed twrp recovery then flash the rom through STOCK FIRMWARE INSTALLER it really was hard for me to do as lack of drivers and non detecting issues with windows 7 but windows 10 solved it at all finally
overall dont mess with an unrooted, locked bootloader watch or mobile
peace
Click to expand...
Click to collapse
Can you help me with boot loop. Uninstalled some apks with the all in one tool (seems some important apks) and the amazfit verge is struck in boot loop as shown in image.
Saratoga79 said:
Uninstall it, and as a last chance, factory reset your watch using adb reboot wipe command. Another way, If the watch still connects to Amazfit app, unpair the watch while Bluetooth is connected, this will factory reset the watch too.
Click to expand...
Click to collapse
What is the remote wipe command for factory reset under fastboot mode? Thank you
Saratoga79 said:
Uninstall it, and as a last chance, factory reset your watch using adb reboot wipe command. Another way, If the watch still connects to Amazfit app, unpair the watch while Bluetooth is connected, this will factory reset the watch too.
Click to expand...
Click to collapse
What is the remote wipe command for factory reset under fastboot mode? Thank you
I am not responsible for bricked devices, dead SD cards, etc!
I have not tested the global unlock, Global version unlock thread.
Make sure you make backups before unlocking the bootloader, as this operation will wipe all user data and apps.
Make sure your system version is the official and latest one.
Requirements
- 60% charge on the phone
- PC and usb data cable
- Installed fastboot and proper drivers on your PC
1. Install Deep Testing Apk attached in this post.
2. Click on the Apply Now button in order to get approval for bootloader unlock.
3. Check the status after apply using the Query Approval Status.
4. If you get an error, force stop the application, change your device language to Chinese and try again (if someone can post screenshot of what to tap, I would update this post)
5. Once the approval is done, tap Start Testing button, this will reboot your device in the bootloader.
6. Last chance, make backups at this point otherwise your data is gone.
7. Run command
Code:
fastboot flashing unlock
8. Done, you can now reboot into system normally
If I missed anything, kindly comment and I'll update OP.
myogui said:
I am not responsible for bricked devices, dead SD cards, etc!
Make sure you make backups before unlocking the bootloader, as this operation will wipe all user data and apps.
1. Install Deep Testing Apk attached in this post.
2. Click on the Apply Now button in order to get approval for bootloader unlock.
3. Check the status after apply using the Query Approval Status.
4. If you get an error, force stop the application, change your device language to Chinese and try again (if someone can post screenshot of what to tap, I would update this post)
5. Once the approval is done, tap Start Testing button, this will reboot your device in the bootloader.
6. Last chance, make backups at this point otherwise your data is gone.
7. Run command
Code:
fastboot flashing unlock
8. Done, you can now reboot into system normally
If I missed anything, kindly comment and I'll update OP.
Click to expand...
Click to collapse
Hi myogui
Do you have the firmware for RMX3300_11_A.19?
Do I run that command from the phone? When I start deep testing and phone reboots I only have the options to start, power off, recovery, and restart bootloader.
I can't get this to work on A19 firmware no matter what I do. Says not supported on this model even though I have the correct RMX3300 so I am going to upgrade to A20 and see if it works
Nope upgrading to A20 doesn't work either. Always get failed to submit in either english or chinese.
wildlime said:
Nope upgrading to A20 doesn't work either. Always get failed to submit in either english or chinese.
Click to expand...
Click to collapse
It did take a couple of tries to get it to work but still that was done in like 10-15 minutes. You could try to factory reset the phone first but if it's still doesn't work for you you'll be stuck re-installing everything on your phone.
wildlime said:
Nope upgrading to A20 doesn't work either. Always get failed to submit in either english or chinese.
Click to expand...
Click to collapse
Same problem. It work for me trying all Chinese languages (simple and another two). It seems stuck for like 30 minutes, then idk why I've exit and re enter the app and it worked.
i cant get my computer to recogize the phone when in bootloader. Anyone else run into this? i ran the fastboot command with the phone plugged in but its still waiting for a device to connect
Bnblare said:
i cant get my computer to recogize the phone when in bootloader. Anyone else run into this? i ran the fastboot command with the phone plugged in but its still waiting for a device to connect
Click to expand...
Click to collapse
Try another USB cable and make sure you are in the folder where fastboot program is.
Bnblare said:
i cant get my computer to recogize the phone when in bootloader. Anyone else run into this? i ran the fastboot command with the phone plugged in but its still waiting for a device to connect
Click to expand...
Click to collapse
Download the attached file, then install manually the driver, select the android_winusb.inf file.
myogui said:
Try another USB cable and make sure you are in the folder where fastboot program is.
Click to expand...
Click to collapse
hacls said:
Download the attached file, then install manually the driver, select the android_winusb.inf file.
Click to expand...
Click to collapse
Thanks! This is definitely a driver issues.
I have an RMX 3300 Chinese model. Build number is RMX3300_11_A.20. When I run the deeptesting_RMX3300.apk it says "Failed to submit application. This phone model does not support deep testing. "
robert3892 said:
I have an RMX 3300 Chinese model. Build number is RMX3300_11_A.20. When I run the deeptesting_RMX3300.apk it says "Failed to submit application. This phone model does not support deep testing. "
Click to expand...
Click to collapse
I finally managed to get past this point. But when I go to step 7 it says waiting for device. I'm using the same USB cable that works for ADB. Might try another cable tomorrow and/or another usb port.
Tried different cables and usb ports. Still stuck on 'waiting for device'
robert3892 said:
I finally managed to get past this point. But when I go to step 7 it says waiting for device. I'm using the same USB cable that works for ADB. Might try another cable tomorrow and/or another usb port.
Click to expand...
Click to collapse
Is a secret how you managed that?
criszz said:
Is a secret how you managed that?
Click to expand...
Click to collapse
I believe that the servers which grant permission for the deep testing app are busy at different times of the day. I simply retried the app during different times of the day until it worked. I still am working on a complete solution
robert3892 said:
Tried different cables and usb ports. Still stuck on 'waiting for device'
Click to expand...
Click to collapse
Fixed this issue finally by installing the android bootloader usb drivers
OK I have this working. I believe I will now need to relock the bootloader
robert3892 said:
OK I have this working. I believe I will now need to relock the bootloader
Click to expand...
Click to collapse
Don't relock the bootloader using the ADB lock command. This will brick your device!
Everithing ok, thanks man.
Hello Every one , mine has Xperia 1 iii bc62 ariginal firmware :61.0.A.11.23 release-keys, when i flashed with lasted firmware 61.1a.11.36 after completed with the newfasher tool i unplug the device press power button but it boot loop several time and show error "Your device is corrupt it cant be trusted and will not boot"
I try with different firmware but get no luck . can some one experient help me with that. thanks
tiinpii said:
Hello Every one , mine has Xperia 1 iii bc62 ariginal firmware :61.0.A.11.23 release-keys, when i flashed with lasted firmware 61.1a.11.36 after completed with the newfasher tool i unplug the device press power button but it boot loop several time and show error "Your device is corrupt it cant be trusted and will not boot"
I try with different firmware but get no luck . can some one experient help me with that. thanks
Click to expand...
Click to collapse
Question: 1. Did you wipe user Data and 2. Did you root it before or after updating?
Ainz_Ooal_Gown said:
Question: 1. Did you wipe user Data and 2. Did you root it before or after updating?
Click to expand...
Click to collapse
Hello, 1 no i didn't
2. I didn't not root it also
tiinpii said:
Hello, 1 no i didn't
2. I didn't not root it also
Click to expand...
Click to collapse
The firmware that you tried to install, is that your "native"?! Is it for XQ-BC62? If yes then why are you trying to update with flashing instead of normal update or xperia companion?!
Also is it for the same country/region as the original? I had the same error when by mistake I downloaded a UK version instead of EEA.
tiinpii said:
大家好，我的有 Xperia 1 iii bc62 原始固件：61.0.A.11.23 释放键，当我用最新的固件 61.1a.11.36 刷新时，在使用 newfasher 工具完成后，我拔下设备，按下电源按钮，但它启动循环几个时间并显示错误“您的设备已损坏，无法信任且无法启动”
我尝试使用不同的固件，但没有成功。有人可以帮助我吗？谢谢
Click to expand...
Click to collapse
你应该没有解锁手机，请刷入原来的固件版本再解锁刷机，我也有类似的问题就是这样解决的。希望能帮助到你
tiinpii said:
Hello Every one , mine has Xperia 1 iii bc62 ariginal firmware :61.0.A.11.23 release-keys, when i flashed with lasted firmware 61.1a.11.36 after completed with the newfasher tool i unplug the device press power button but it boot loop several time and show error "Your device is corrupt it cant be trusted and will not boot"
I try with different firmware but get no luck . can some one experient help me with that. thanks
Click to expand...
Click to collapse
I have just had the same issue using newflasher. I don't believe i made any mistake during the process. Had to do a Xperia Companion Repair to repair. Resulting in a complete loss of data.
defsix said:
I have just had the same issue using newflasher. I don't believe i made any mistake during the process. Had to do a Xperia Companion Repair to repair. Resulting in a complete loss of data.
Click to expand...
Click to collapse
What version of newflaher are you using?
Latest version from end of last year. I actually checked this after it failed
What did you type before you flash like yes and no in the beginning ?
defsix said:
Latest version from end of last year. I actually checked this after it failed
Click to expand...
Click to collapse
99% of all failures I have had when using Newflasher have been caused from poor USB connection. I now have a very specific USB cable that I only use when flashing files to Sony devices. I also close nearly all background programs and disconnect any non essential USB devices.
If you all use newlfasher type all N when it ask for Y or N except for keep userdata thats an Y, thats it, never had an issue with Newflasher on my Xperia 1 iii.
bentree said:
99% of all failures I have had when using Newflasher have been caused from poor USB connection. I now have a very specific USB cable that I only use when flashing files to Sony devices. I also close nearly all background programs and disconnect any non essential USB devices.
Click to expand...
Click to collapse
Yeah, first time I didn't use the Sony Original cable... Lesson learned.
Pandemic said:
What did you type before you flash like yes and no in the beginning ?
Click to expand...
Click to collapse
Sorry, I missed your question. No to all the questions, with reboot at the end
tiinpii said:
大家好，我的有Xperia 1 iii bc62 ariginal固件：61.0.A.11.23释放键，当我使用最新的固件61.1a.11.36刷新时，使用newfasher工具完成后，我拔下设备按电源按钮，但它启动循环几次并显示错误“您的设备已损坏，无法信任，无法启动”
我尝试使用不同的固件，但没有运气.有人可以帮我吗？谢谢
Click to expand...
Click to collapse
一定要解锁BL才能降级，建议网上搜索解锁教程
My Xperia 1 iii have same issue, also it keep showing "Your device is corrupt it cant be trusted and will not boot Your device will be powered off in 5 second"
I've tried all method to put it to recovery mode but failed.
Any one could help?
For my XQ-BC62, I ended up getting the device is corrupt issue after flashing the rom via fastboot instead of via fastbootd. (it's confusing bc you have to use fastboot to unlock the bootloader, not fastbootd). To fix it, Xperia companion software told me to use Emma, so I downloaded that and was able to restore stock firmware to the device.