Success is disgusted by some people, and will not share any files for free in the future.
Your Post Very Helpful For Us ,
I Am Test This File Then Post Result , Thanks For This File Provide !!!
johnny886 said:
In China, this Phone is called Nubia Play, and the Global version is called Redmagic 5G Lite,
but the mobile phone model is NX651J. Generally speaking, the two are only the difference in ROM.
This is the edl firmware of Nubia Play,CN version.which can repair your phone in edl mode.
All the files are from the official package without any modification!
How to do?
1.Open XiaoMiFlash.exe in the MiFlash folder
2.Click the select button to select the images in this firmware
3.The phone enters edl mode and connects to the computer with a usb cable
（If your phone is in edl mode (9008 mode) for a long time, you must long press the
power button volume + and volume-keys to force the phone to power off, and then re-enter edl mode）
4.Click Loading and see the COMxx that appears, indicating that your phone is connected. Then click Flash
5.Then just wait, prompting flash done！sucess! It means that the flashing has been completed,
long press the power button to restart the phone!
When you see the green notification light next to the front camera light up,
you can release the power button.
Good luck！Enjoy it！！！
Download link：
https://mega.nz/file/eNkVSA6T#2yN_JHtOxB_K4NHVTF3qT_asMMFtnEKBQ6sQ8b-y2nU
Click to expand...
Click to collapse
Only spanish?
GSM KING MAKER said:
Your Post Very Helpful For Us ,
I Am Test This File Then Post Result , Thanks For This File Provide !!!
Click to expand...
Click to collapse
Is global rom? Only spanish?
thequellu said:
Is global rom? Only spanish?
Click to expand...
Click to collapse
Its Not Global Rom , Only Chinese Firmware !
Why do I use scarlet letter when I use flash
The brick tool has worked on a few occasions ,thank you for that but now I need more help or suggestions, when playing between the Spain ROM and China version I lost the baseband and IMEI.Then I thought,locking the bootloader back would help obviously it did not work. Now even though I flashed the unbrick tool though miflasher edl mode I am stuck with a blank screen after the Nubia logo and port Qualcomm 900e in Windows device manager.
Tried already via recovery to flash an update China version or Spain version they flashed fine however still same scenario after Nubia logo.
Not sure what my options are.
Does this work for updating or just brick?
DargorDG said:
Does this work for updating or just brick?
Click to expand...
Click to collapse
It does work to fix the update errors and then use the OTA or USB Otg method
@johnny886
Thank you for the tool.Just wondering if there is a version for Android 11 as i updated to 3.16 android 11 firmware via the usb and now I get your device is corrupt.
Obviously my problem dates back to unlocking and then relocking the bootloader which somehow bricked the phone. Even though before relocking the tool worked once the bootloader was locked the phone wasn't able to boot into system but I was not getting the device is corrupt.
I am hoping for a way to unlock the bootloader or to be able to get back into the system to tick the option in the developer settings hence I am keeping my hope for an updated unbrick tool.
I donwload the file and uncompress it, when select the folder with XiaoMiFlash is shows "could't find flash script".
There are no flash_all.bat file on folder
any help, where is that file?
(mega interrupt the download process)
@ecatombe1234
In my case said the same with regards the script but had flashed fine once started.
Just be careful if you have the bootloader unlocked do not lock it again with the fastboot flash lock.
Thanks for you, really soon, response.
Yes, I try, put phone in edl mode, refresh, flash, and recive [... COM8]:ERROR_UNSUPPORTED_TYPE 0
@ecatombe1234
Usually this is down to the drivers used for Qualcomm Edl mode. Have you installed them ?
Is the EDL mode phone recognized in the device manager as Qualcomm??
Yes, I have correct drivers, I restored the phone last year, but not now.
Xiaomi tool detects phone in bootloader and in edl mode.
Windows detect phone in edl mode as: Qualcomm HS-USB QDLoader 9008 (COM8).
I tried with QFiL too, but I am not sure the config to work qith this, because it detect mobile in edl mode.
Any way, Xiaomi tool has very few config options, I can's understand the "could't find flash script", can any one give us ligth about this error?
It was xiaomi flash tool version, I tried a lot, finally this one works, it is the only one that works with corrupted android 11 version.
Download Xiaomi Flash Tool- v20210226
Mi Flash tool is meant for all Qualcomm powered Xiaomi and Redmi phones on which you can flash MIUI Fastboot ROMs. It works over the Fastboot connection to erase and…
droidfilehost.com
That will work to my dead boot nubia paly 5g?
@ecatombe1234
Thank you for the version even though this version got me a bit further in a Chinese testing menu still couldn't boot into system .
Must be something to do with the relocking of the bootloader.
Helo guys.. How can I downgrade from android 11 back to android 10 on this device? I recently updated my software but It is not stable yet. Certain apps for example PUBG mobile keep crashing whenever I try to launch it.
Mitchpop said:
@ecatombe1234
Thank you for the version even though this version got me a bit further in a Chinese testing menu still couldn't boot into system .
Must be something to do with the relocking of the bootloader.
Click to expand...
Click to collapse
I've been following your discussion on this thread and had the same problem after ota update to 3.16.
I also had initially difficulty flashing with MiFlash but finally it worked.
I immediately pressed the flash after entering EDL mode
My phone flashed and entered the Chinese mode. I then went to bootloader by hard pressing the power button and Vol down key.
In bootloader I entered recovery which allowed me to update using OTG. I used a flash with USB C and loaded the phone with NX651J v 22 and my phone is back to the previous settings.
Related
Hello my friend just made an update of his phone which is a redmi 3 pro
His little bro shutdowned the phone while update was in process. The result is that now the phone have a bootloop, can't access the recovery (blackscreen when trying) and have a locked bootloader.
So I am not sur how to unlock the BL if I can't install a dev rom and can't boot. Not sur how to get into the recovery with the 2 same problems.
Could anyone help me for this one? Which is hard to me.
Thanks
PS: I tried to do something with unpacking boot and remove a ",verify" thing in the ramdisk but I guess I'll need the unlockedbootloader to flash the new boot.img?
Kicroy said:
Hello my friend just made an update of his phone which is a redmi 3 pro
His little bro shutdowned the phone while update was in process. The result is that now the phone have a bootloop, can't access the recovery (blackscreen when trying) and have a locked bootloader.
So I am not sur how to unlock the BL if I can't install a dev rom and can't boot. Not sur how to get into the recovery with the 2 same problems.
Could anyone help me for this one? Which is hard to me.
Thanks
PS: I tried to do something with unpacking boot and remove a ",verify" thing in the ramdisk but I guess I'll need the unlockedbootloader to flash the new boot.img?
Click to expand...
Click to collapse
I have the similar problem with my Redmi3. The Fastboot screen is the only screen that I can get now. Let me know if you have answer. Thanks.
If you can acces fastboot then just connect the phone to computer in fastboot and enter fastboot oem edl in cmd (maybe you will need Minimal ADB and fastboot to do it). Then flash official ROM via MiFlash.
ohoh seems interesting then it won't say couldn't verify or smthg? will tell that to my friend asap, thanks
EDL mode allows flashing with locked bootloader. Some models have this mode locked, but I think that is not the case with Redmi 3.
Kicroy said:
ohoh seems interesting then it won't say couldn't verify or smthg? will tell that to my friend asap, thanks
Click to expand...
Click to collapse
to go to edl mode just turn off your phone.plug the cable to your laptop or desktop but not to your phone.now be ready to press both volume up and down button as you plug the usb cable to ur phone.immediately after inserting the usb cable press both volume buttons at the same time.it should vibrate and go to edl mode.edl mode appears in black screen so to know if its in edl mode or not open miflash and click refresh ,your device should be shown as com10,20 or com something like that .once you go to edl mode you know what to do if you have used miflash to flash roms.hope this helps you.
jokerpappu said:
to go to edl mode just turn off your phone.plug the cable to your laptop or desktop but not to your phone.now be ready to press both volume up and down button as you plug the usb cable to ur phone.immediately after inserting the usb cable press both volume buttons at the same time.it should vibrate and go to edl mode.edl mode appears in black screen so to know if its in edl mode or not open miflash and click refresh ,your device should be shown as com10,20 or com something like that .once you go to edl mode you know what to do if you have used miflash to flash roms.hope this helps you.
Click to expand...
Click to collapse
I have a problem with my redmi 3. It makes reboot and it does not charge if its not closed.
Can you help me to fix or do you now where i can find a solution.....
geuthym said:
I have a problem with my redmi 3. It makes reboot and it does not charge if its not closed.
Can you help me to fix or do you now where i can find a solution.....
Click to expand...
Click to collapse
Well about that i dont know.but your best bet to solve it is by changing the software.if that does not helps then you should take your device to a technician for repairing.
jokerpappu said:
Well about that i dont know.but your best bet to solve it is by changing the software.if that does not helps then you should take your device to a technician for repairing.
Click to expand...
Click to collapse
When i bouht it the software it was unnoficial then i put with miflash the china dev. All the problem start when i make updates apps and the android web view.
geuthym said:
When i bouht it the software it was unnoficial then i put with miflash the china dev. All the problem start when i make updates apps and the android web view.
Click to expand...
Click to collapse
try flashing official global rom then see if the problem still persists or not
Hey! I am back with some news of my friend!
He tried to run the EDL mode but when he does that the phone simply goes into the bootloop again... He asked a vendor from Aliexpress to get a french rom, is there a way that the phone doesn't have EDL because of the rom or something like that? I mean is EDL a hardware-thing or a software-thing
same problem
cukru said:
If you can acces fastboot then just connect the phone to computer in fastboot and enter fastboot oem edl in cmd (maybe you will need Minimal ADB and fastboot to do it). Then flash official ROM via MiFlash.
Click to expand...
Click to collapse
I have same problem, but this way is not work, because bootloader is locked. Im forget for replacing recovery.img in update package with twrp.
I had this problem before few monthes
my solution was to "force" putting this device on EDL mode
I clicked on vol up + vol down + power together and got into EDL mode, then miflash it.
google - xiaomi understanding download mode
it will send you into miui forum
then second method, download mode, it is what I've described
I know there is few hundered threads with "unbrick" in title but I read them all and nothing seems to work.
Friend brings me kenzo that he gets since his cousin brick it while trying OTA.
When I power phone its start to load system and it has 3 stages:
1. Show screen with "powered by Android" and 3 dots in the bottom, usualy about 4 min and restart
2. After restart just get black screen with Mi logo in the middle, for about 30 sec and restart
3. Instead of Android with dots bottom have white line progres bar, it takes 4 to 5 min and restart again.
After that stage 2 and 3 repeat for long as you have nervs to wait .
Phone can get in recovery and fastboot mode. And when I put him in test mode just show test screen and cant do anything.
In fastboot mode MiFlash recognize phone but report "device is locked" (try with 20160401 and 20160830).
After that i put him in EDL mode (fastboot reboot-edl) and MiFlash report successful flash. But nothing changes.
I try flashing global stable v8.0.5.0, china stable v8.0.4.0, global dev v6.10.13 and at the end global stable v7.2.5.0.
Any idea welcome. Thx
Have you tried to unlock bootloader? Perhaps install TWRP and do a system/dalvik/cache wipe and install MIUI through that?
banana_bender said:
Have you tried to unlock bootloader? Perhaps install TWRP and do a system/dalvik/cache wipe and install MIUI through that?
Click to expand...
Click to collapse
Cant do that. Even unofficial unlock need phone to be working to enable USB debbuging and accept RSA kay from PC.
Edit: Right now looking for ways to edit boot.img to unlock bootloader in attempt to get any useful recovery.
you can try this guide to flash twrp altogether with rom. after flashing, directly boot to twrp and move to custom rom
abihary said:
you can try this guide to flash twrp altogether with rom. after flashing, directly boot to twrp and move to custom rom
Click to expand...
Click to collapse
I will try... but dont think it will do the job. Will post result little later.
EDIT
It dose not work, just as I think.
All that kind of method/advice need 2 things:
1. Enabled USB debbuging - You cant do that on bricked phone even if you edit boot.img ( ro.debuggable=1 ) because fastboot will not execute command since you will not have option to accept RSA kay from PC on your phone and complete that action.
2. Dev ROM - since you have to enable OEM unlock and that option you have only in dev ROMs. Even Xiaomi official unlock requires that you must do it on dev ROM and that is a reason for "stuck on 50% in unlocking".
I try all that I can think: edit boot.img file, use patch emmc_appsboot.mbn, use edited flash_all.bat and rawprogram0.xml, insert sTWRP and ZCX TWRP in fastboot ROM... and all combination of that. Did it on 7.2.5.0 and 8.0.5.0 stable and 6.8.18 dev (since its last 5.1 ROM that I have).
Most of this attempts ends with "3 stages" explained in the first post. Some just show Mi logo for few sec and restart, once even power off phone. And once I even get phone to go directly to sideload/recovery state showing picture of the phone and usb cable.
Only thing left now is to find info is there difference in accessing to EDL mode between software (reboot-edl), deep flash cable and testpoint. IMHO there is none or little difference. Since software and deep flash can be troubled with bad USB cable or connector or USB board in phone.
WARNING, THIS GUIDE WILL WIPE ALL THE DATA IN YOUR DEVICE.
!!! Whatever you do, it is at your own risk !!!
This procedure will unbrick any Axon 7, returning it to stock. It fixes any kind of brick as long as your hardware is not damaged. You can't damage your hardware using software so if you have a healthy unit, you can recover it from any flashing "accident".
1. GET THE SOFTWARE
You need a Windows PC, Windows 10 is highly recommended. Do this:
01. Install MiFlash in your PC. It includes the Qualcomm Snapdragon SoC drivers, nonetheless you can always install the latest drivers.
02. Download the EDL flashable stock firmware package for your model:
A2017 (China): B14_MIFAVOR5 Android: 7.1.1
A2017G (Europe): B10_NOUGAT Android: 7.1.1
A2017U (Americas): B35_NOUGAT Android: 7.1.1
03. Unzip the firmware ZIP file to a folder in your hard drive.
2. ENTER EDL MODE
Option A: USING THE REBOOT COMMAND
If you still have access to your system but not to recovery or fastboot, then you just need to install any terminal app, open it and at the app's command prompt enter:
Code:
reboot edl
. You device will reboot into EDL mode. Now you can safely plug your Device to your computer. In your computer right click in the Windows Start Menu icon and select Device Manager. Under Ports (COM & LPT) your device should appear as Qualcomm HS-USB QDLoader 9008 using a virtual COM port. If you can see it, then you can continue to the flash section, step 14. Otherwise, if you do not see anything or a DFU device, then you'll need to explore the next option.
Option B: USING THE BUTTON COMBO
04. Press the VolUp and VolDn buttons in your device and keep them pressed.
05. Now press the power button until the red LED flashes, it does it really quick. Then release the buttons, starting by the power button.
06. Plug the device to your computer.
In your computer right click in the Windows Start Menu icon and select Device Manager. Under Ports (COM & LPT) your device should appear as Qualcomm HS-USB QDLoader 9008 using a virtual COM port. If you can see it, then you can continue to the flash section, step 14. Otherwise, if you do not see anything or a DFU device, then you need an EDL cable.
OPTION C: USING THE EDL CABLE
So, you need to get a Qualcomm EDL cable. With it you can recover from any situation. I use this one, DrakenFX uses this other model. There are cables out there not working properly so do not try to save 4 or 5 bucks and get yours from a reliable source. Alternatively you can solder your own by following this guide. If you are in an emergency (or your patience threshold is very low) and have a thin wire around you, then you can follow this DIY hack video.
Do you already have the EDL cable? then follow these steps:
07. Connect your bricked Axon 7 to your PC using the EDL cable.
08. Press the EDL cable button and keep it pressed.
09. Press the Power button of your bricked unit and keep it pressed too.
10. Wait 20 seconds.
11. Release the power button.
12. Wait 10 seconds.
13. Release the button of the EDL cable.
Voilà, your device is now in EDL mode. The device manager in your PC, under the ports category, should detect it as Qualcomm HS-USB QDLoader 9008. Now you can proceed to the flash section. If this procedure doesn't work, then your unit could have a hardware problem. Your only hope is to dissemble it by following this last resort guide.
3. FLASH FIRMWARE
14. Open MiFlash in your computer.
15. Click Browse button and select the folder you created in step 03 with the stock firmware files.
16. Click Refresh button and your device will appear listed as virtual COM port.
17. Click Flash button and wait for a few minutes until it finishes. Note that the bottom options are not applicable.
18. Now you have a stock Axon 7. Your data partition will still have garbage data, so you should enter recovery by pressing VolUp while rebooting your device with the power button. Release VolUp only when you reach Recovery. Using Recovery do a Factory Reset of your device.
That was the last step. Hopefully now you have a fully functional stock Axon 7.
By the way, this guide can also be used to return to stock any working device for selling or service!!!!
Cheers!!!!
Nice! I just disassembled mine and did it that way the other day.
thank you.
i will save the files and guide for rainy day.
i have A2017 that i converted into A2017U; which file do i need to download?
@Oki
Thnx for this guide :good:
Find the latest A2017G N-B10 here
Harmtan2 said:
Nice! I just disassembled mine and did it that way the other day.
Click to expand...
Click to collapse
Glad to see you solved your issue.
mb0 said:
thank you.
i will save the files and guide for rainy day.
i have A2017 that i converted into A2017U; which file do i need to download?
Click to expand...
Click to collapse
I don't know what you mean about converting an A2017 into an A2017U. They are the same device except for the radio, that that's a hardware difference. You should always use the right modem firmware for your radio hardware so you should use the A2017 modem firmware. After unbricking your unit, you can unlock it again and flash any universal firmware the same way you did before. It is a long but safe process.
yes, i meant to say that i flashed U radio over my A2017
so China version is for me.
mb0 said:
yes, i meant to say that i flashed U radio over my A2017
so China version is for me.
Click to expand...
Click to collapse
If you flashed the A2017U radio in a A2017 hardware and worked fine for you, then you can use the A2017U B35 stock firmware.
What will be the bootloader status after following this guide? I need my phone with a locked bootloader.
My phone shows up as Handset Diagnostic Interface (DFU) (COM3) but it doesn't get detected on Miflash program......
aLexzkter said:
What will be the bootloader status after following this guide? I need my phone with a locked bootloader.
Click to expand...
Click to collapse
It should be locked. But in case you end up with an unlocked phone, then locking it is very easy. You only need to connect your phone, enter into fastboot mode, download the adb/fastboot tools and execute the command fastboot oem lock from your computer.
Oki said:
It should be locked. But in case you end up with an unlocked phone, then locking it is very easy. You only need to connect your phone, enter into fastboot mode, download the adb/fastboot tools and execute the command fastboot oem lock from your computer.
Click to expand...
Click to collapse
I can't get into EDL mode. I hold down volume buttons, then power. When the red led lights up, I unpress power, then the volume buttons, connect the USB cable and nothing happens on my phone (black display) red led still on. On my computer I see ZTE Handset Diagnostic Interface(DFU) (COM3).
Edit: I managed to get into EDL mode thanks to Axon 7 EDL Tool but I got a "File analysis: error" "not important files found" so I went back to MiFlash and also got an error about the files. Will update the post when I get it to work.
aLexzkter said:
I can't get into EDL mode. I hold down volume buttons, then power. When the red led lights up, I unpress power, then the volume buttons, connect the USB cable and nothing happens on my phone (black display) red led still on. On my computer I see ZTE Handset Diagnostic Interface(DFU) (COM3)
Click to expand...
Click to collapse
You can enter EDL mode from the system. Just install any terminal app, open it and enter the command reboot edl
Oki said:
You can enter EDL mode from the system. Just install any terminal app, open it and enter the command reboot edl
Click to expand...
Click to collapse
xD My phone was bricked. I thought this tutorial was mainly targeted for bricked devices.
Anyway, my phone is working now. The downloaded EDL zip was corrupt so it only had a few files inside.
@Oki
Edit: I have a working phone on Nougat B10. But I can't lock the bootloader because I don't have access to fastboot. My phone's variant is A2017G
aLexzkter said:
xD My phone was bricked. I thought this tutorial was mainly targeted for bricked devices.
Anyway, my phone is working now. The downloaded EDL zip was corrupt so it only had a few files inside.
@Oki
Edit: I have a working phone on Nougat B10. But I can't lock the bootloader because I don't have access to fastboot. My phone's variant is A2017G
Click to expand...
Click to collapse
Glad to see you solved your issue. I misunderstood your problem. I thought you had access to the system and not to recovery or fastboot. Anyway, this guide is for unbrick or return to stock. I'll investigate the relock problem. Usually clearing devinfo partition should be enough to relock any bootloader.
Oki said:
Glad to see you solved your issue. I misunderstood your problem. I thought you had access to the system and not to recovery or fastboot. Anyway, this guide is for unbrick or return to stock. I'll investigate the relock problem. Usually clearing devinfo partition should be enough to relock any bootloader.
Click to expand...
Click to collapse
In order to get access to fastboot I had to use the tool Axon7Toolkit, select "unlock bootloader" option, make sure you have an old version of MiFlash installed (20161212) and then you can select "lock bootloader" on Axon7Toolkit.
Thanks for everything.
aLexzkter said:
In order to get access to fastboot I had to use the tool Axon7Toolkit, select "unlock bootloader" option, make sure you have an old version of MiFlash installed (20161212) and then you can select "lock bootloader" on Axon7Toolkit.
Thanks for everything.
Click to expand...
Click to collapse
Well, I am considering to link the older Marshmallow ROMs since the Nougat ROMs have some issues with fastboot. Anyway. It is going to take some time to test the alternatives. Thanks for letting us know!
Some of the most recent firmware for Axon 7 (@NFound's B12 bootstack, I think) doesn't support the EDL button combo. But if you have TWRP installed, you can boot to recovery, then reboot to EDL from there.
I kept getting the device registering in device manager in DFU mode. But I noticed that it briefly registers as QUSB_BULK before reverting to DFU. So I installed zadig winUSB driver and now it registers as QUSB_BULK when I turn on the device pressing all 3 buttons.
How can I proceed now?
Hi there
Thanks for this guide. I have a 2017U, so I got A2017U_B35_NOUGAT_FULL_EDL.zip file. After unzipping and connecting the phone to the computer it gets properly recognized and i can start the process from the MiFlash program. After reaching somewhere between 30-40% of the flashing process, it goes suddenly to 100% and it says that is finished. When I reboot the phone, it appears as if I was still under an unlocked bootloader (warning message + TUX penguin image) and the phone starts but during the initial setup process, i chose to start as a new phone but it says that "This device was reset. To continue, sign in with a Google Account that was previously synced on this device" and obviously this is not what I am interested for.
How can I get rid of this message and get a full clean install, with bootloader relocked and all that??
Thank you for any help you can provide!
Flogisto said:
Hi there
Thanks for this guide. I have a 2017U, so I got A2017U_B35_NOUGAT_FULL_EDL.zip file. After unzipping and connecting the phone to the computer it gets properly recognized and i can start the process from the MiFlash program. After reaching somewhere between 30-40% of the flashing process, it goes suddenly to 100% and it says that is finished. When I reboot the phone, it appears as if I was still under an unlocked bootloader (warning message + TUX penguin image) and the phone starts but during the initial setup process, i chose to start as a new phone but it says that "This device was reset. To continue, sign in with a Google Account that was previously synced on this device" and obviously this is not what I am interested for.
How can I get rid of this message and get a full clean install, with bootloader relocked and all that??
Thank you for any help you can provide!
Click to expand...
Click to collapse
There ate several ways to remove that. One involves TWRP 3.2.1-7 and the other Axon 7 EDL tool, if you dont have TWRP then use the second . Jusy go to the unlock menu and apply the google unlock.
A third way would be to setup the phone with your old google account and do afactory reset from within Android, not from the bootloader. That would remove also the owner safety.
Thank you so much for your guide and software bundle.
I even had to make a EDL cable to restore my device.
After flashing, I do not see vendor as a partition but looks like it is a folder. Is it OK for future ROMs ?
Hello, i have a hard bricked Huawei mate 10 ALP-l29 with all partitions deleted. Bootloader is locked and no chance to unlock.
Tried all services - nothing!
Is it any hope?
I like this phone damn.
LisKelAlb said:
Hello, i have a hard bricked Huawei mate 10 ALP-l29 with all partitions deleted. Bootloader is locked and no chance to unlock.
Tried all services - nothing!
Is it any hope?
I like this phone damn.
Click to expand...
Click to collapse
You deleted all positions with bootloader locked?
Bad idea. Sounds like your device is really hard bricked ... Sorry
......
It_ler said:
You deleted all positions with bootloader locked?
Bad idea. Sounds like your device is really hard bricked ... Sorry
Click to expand...
Click to collapse
Flashed wrong (online) software via DCPhoenix. It flashed but never turned on. Went black, no update mode, no revovery mode. Nothing. But PC detects it.
Solved via testpoint with Octoplus Huawei
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
UNBRICK TOTALLY BLACK SCREEN HUAWEI USING OCTOPLUS HUAWEI:
Download the SAME as on your phone OR NEWER SERVICE - OFFLINE FIRMWARE,
(2 versions here: https://mega.nz/file/lANCTZoR#GbFZEYnNOsyRLIAZVNYFO02cL5pp1OhTAN_naYyQgk0
https://mega.nz/file/kJVikZhA#Rn4VkQKYOJmKTrnKBLEHy8i82i7D3sB6MAT7hQWz4x4).
Enable downgrade on OCTOPLUS REPAIR option while in testpoint if you want to flash a lower version!!!
Open back cover
Remove bat and lcd CONNECTIONS
Connect to PC
Make testpoint
Reconnect bat and lcd
Find mobile driver (I should be USB SER or something like that) on PC Manager
Update driver manually BY INSTALLING HUAWEI INTEGRATED USB COM 1 DRIVER
...UPDATE, FROM PC, FROM this PC, HUAWEI INTEGRATED, USB COM1.
LAUNCH OCTOPLUS
REPAIR AND Update BACKUP (BOOTLOADER - OEM info) -Set the version you have.
Enable downgrade on OCTOPLUS REPAIR option while in testpoint if you want to flash a lower firmware version!!!
After success repair it will reboot in fastboot mode - temporary unlocked bootloader.
(Dont try flash TWRP - it will never load)
Flash software by selecting fastboot mode and only the 2 files - base update and cust update
extracted from downloaded zip
When firmware loaded to phone it will ask you to access download mode
If Octoplus cant access download mode, do it manually (+- buttons and power. When vibrates, RELEASE power and whait for download screen while still holding +- buttons. Release +- buttons when on download mode)
BE CAREFUL: DONT TURN ON THE PHONE, and DONT UBPLUG FROM PC - BOOTLOADER WILL BE RELOCKED AND YOU CANT FLASH!
Confirm FLASH in octoplus.
Flash...
Anyway, when Octoplus asks to access download mode, means bootloader is fixed
so you can flash also using sd card or usb key (insert dhe dload firmware to sd or usb)
by force download.
+-, power buttons.
I accidentally bricked my phone after successfully flashing a miui rom in MiFlash. After flashing on MiFlash, my device stopped functioning. The only response I could get from it was in the miflash. I already tried flashing firmware I watched on y0utu;e i think it works but there's an error saying "you are not authorized to download!!" In the middle of flashing. I'm worrying that there is no hope for my device anymore.
Is possible to put the device on EDL MODE.
Hold volume up and down and when you hold them connect the device on pc.
If you listen a sound is recognized like edl mode.
After that flash by miflash tool a stock rom without aythorazation.
You can find this rom at telegram in mi a3 miui updates..
Good luck.
Try to flash via miflash firmware conversion mia3 to cc9e https://sourceforge.net/projects/mia3-to-micc9e-conversion/files/Conversion_EDL_Firmware/
papsr6 said:
Is possible to put the device on EDL MODE.
Hold volume up and down and when you hold them connect the device on pc.
If you listen a sound is recognized like edl mode.
Click to expand...
Click to collapse
wetito said:
Try to flash via miflash firmware conversion mia3 to cc9e https://sourceforge.net/projects/mia3-to-micc9e-conversion/files/Conversion_EDL_Firmware/
Click to expand...
Click to collapse
Thank you so much you guys! This restored my phone. Note for anyone that want to restore the Xiaomi Mi A3 phone, you also have to install the Qualcomm HS-USB QDLoader 9008 drivers. I uploaded a zip file of the drivers for anyone that want to download it.
After you restore the phone. You can use the miflash program to flash a fastboot stock rom. After you downloaded and extracted the fastboot stock rom, you have to the replace the original prog_firehose_ddr.elf file in the images folder with a modified one. I uploaded the zip file of the modified prog_firehose_ddr.elf file for anyone that want to download it.
Xiaomi Firmware Updater
The ultimate script that provides firmware packages for Xiaomi devices.
xiaomifirmwareupdater.com
If you get the error message 'cannot receive hello packet' while in EDL Mode. You have to power cycle the phone by holding the power button for about 15 seconds. After the phone is turned on, turn it off. Then go back to EDL mode by holding the volume up and down button and then connecting the phone to the computer.
I'm also uploading XiaoMi Mi Flash 20.3.14.0 for anyone that want to flash to the stock fastboot firmware.
xdadev_user11 said:
Thank you so much you guys! This restored my phone. Note for anyone that want to restore the Xiaomi Mi A3 phone, you also have to install the Qualcomm HS-USB QDLoader 9008 drivers. I uploaded a zip file of the drivers for anyone that want to download it.
Click to expand...
Click to collapse
you're welcome! i'm happy my hold posts can be usefull
my mi a3 got hard brick ( i had any thing working - no charging led - no vibration)
after searching a lot i did this :
1: https://c.mi.com/thread-3527044-1-1.html
2: when your phone is powered off and you want to enter EDL mode hold power and volume up and down after 15 sec plug cable to pc
then use QFIL
after that i got #fire hose fail# error in QFIL
So i found this solution:
3: www.youtube.com/watch?v=IxDzvRnB7fY
then returned to 2 step and i recovered my phone to fastboot screen and then used mi flash tools to install stock frimware
wetito said:
Try to flash via miflash firmware conversion mia3 to cc9e https://sourceforge.net/projects/mia3-to-micc9e-conversion/files/Conversion_EDL_Firmware/
Click to expand...
Click to collapse
xdadev_user11 said:
Thank you so much you guys! This restored my phone. Note for anyone that want to restore the Xiaomi Mi A3 phone, you also have to install the Qualcomm HS-USB QDLoader 9008 drivers. I uploaded a zip file of the drivers for anyone that want to download it.
After you restore the phone. You can use the miflash program to flash a fastboot stock rom. After you downloaded and extracted the fastboot stock rom, you have to the replace the original prog_firehose_ddr.elf file in the images folder with a modified one. I uploaded the zip file of the modified prog_firehose_ddr.elf file for anyone that want to download it.
Xiaomi Firmware Updater
The ultimate script that provides firmware packages for Xiaomi devices.
xiaomifirmwareupdater.com
If you get the error message 'cannot receive hello packet' while in EDL Mode. You have to power cycle the phone by holding the power button for about 15 seconds. After the phone is turned on, turn it off. Then go back to EDL mode by holding the volume up and down button and then connecting the phone to the computer.
I'm also uploading XiaoMi Mi Flash 20.3.14.0 for anyone that want to flash to the stock fastboot firmware.
Click to expand...
Click to collapse
Really good. It seems like a miracle that my PC detects my phone connected to a COM3 port. Anyway, it does not make a difference when holding the power button for the 'hello packet' message.
Anyway, an EDL wire is necessary to flash it.