my x10 die suddenly, there was 94% battery left, not plugged out long, few hrs later notice phone was off,and it will not power on again, press power to try to turn it on all it does is vibrate and that's it.
tried to flash stock 2.1 back on but not sure if it did anything, took over night or flash tool to finish, still no boot after that, press power and it vibrates that's all, sometimes it doesn't even vibrate, battery is good, works fine in another x10, put a fully charge battery in it and same result.
anyone know what happened to it?
was running eternity 3a rooted with DT.
I'm going to have to send that in for warranty, hope they won't find anything on it and void the warranty.
Was the phone quite hot at the time or heating up when trying to boot?
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
sharathx10 said:
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
Click to expand...
Click to collapse
That usually does the trick. Unplug battery for 1 minute, reinsert it and try again.
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
do you have a SD card inside. Might be a bad SD card try taking it out and booting it. Happened to me before.
blagus said:
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
Click to expand...
Click to collapse
Hi, just wanted to jump in and ask a few questions about this situation.
Do you always experience this issue? How long before it freezes? What "act" are you doing to prevent freezing? Does the phone work normally afterwards?
Hope you can help me out with some answers, I want to look into this.
instead of starting a new thread,i'll post here..
i have this restart problem..
Before this i try to fix my friend X10.. after many tries and a month acctually,i give up..
Now one more of my friend gave me another X10 which have the same problem..
Problem:
The phone will boot but after several minutes it will auto shut down and when i try to power up no vibrate and stuck at black screen.
when i pull the battery out and on again it vibrate and boot.just after boot animation it will shut down again..
Solution that i have tried so far:
Update with SEUS.
Send to profesional phone service to downgrade to 1.6.
Upgrade/flash with flash tool with GENERIC
Upgrade/flash with flash tool with X10_1.0_SE_StockRom_MultiTouch
Wipe user data in flash tool & x recovery
after several tries i got it work and i root and install x recovery.
Flash from xrecovery with custom rom Eternity.build003a.signed
format memory card.
Change battery.
All the solution i've tried doesn't make the problem dissappear.
anyone have ideas or solution?
Hey guys i've a problem with my x10
So one night i was playing with it than the other day the phone would start
so i thought yeah right might be the battery or something. i took it to my friends x10 it was with 87% charged so i exclude this
Than i tried to flash with flashtool a new kernel and i get stuck at 9% or 15% depending on the kernel i use.
With SEUS it starts to repair but it says. No new updates avaiable after a few moments.
Some information regarding my phone
Unlocked Bootloader
FXP KERNEL
MM TEAM MIUI V4
The phone vibrate but doesn't start or load the kernel.
What do i do?!
Srry for my bad english
Thx in advance
Usrle flashtool to reflash kernel or firmware.
already did but i get stuck at 9% or 15% flashing the kernel
I'm downloading a full generic rom x10a
having similar problem
Hi, I had similar problem as well
X10i running FXP CM7 suddenly just wont boot n charge after I turn off the phone
it wont boot after flashing anything (firm or kernel) except the official firm
now that I end up with a cap R bootloader but flashtool claim that bootloader is rooted
do I still keep the bootloader unlock?
i guess you have a locked bootloader since the original firmware is loading just fine even tho rooting has nothing to do with the bootloader it self. i'm only guessing.
I'm stuck at. Flashing Loader
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
[XBOCT]™ said:
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
Click to expand...
Click to collapse
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
same problem repeat
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
mooving said:
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
Click to expand...
Click to collapse
i'm using
X10a_2.1update1_r2.1.A.0.435_Generic.ftf
And it get stuck at Flashing loader
Idk but i can "read" the kernel when i dump the propriets but i can't "right" when i try to flash something
Anyone?
guys?
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
LJE said:
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
Click to expand...
Click to collapse
maybe i'm wrong idk maybe is a soft brick. thats why i'm asking for some help.
almomdegal said:
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
Click to expand...
Click to collapse
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Try wotanserver's flashtool...
http://www.wotanserver.com/en/
Good luck
SysGhost said:
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Click to expand...
Click to collapse
Didn't work, i even use my friends battery to flash it and it didn't work
almomdegal said:
Didn't work, i even use my friends battery to flash it and it didn't work
Click to expand...
Click to collapse
Well, if the battery issue was fixed, and you're sure the battery is fully charged, then try this: (Quoting from my other post)
I've charged/replaced the battery, and are having trouble with starting up. Earlier flash failed. Now what?
Don't worry. It's pretty darn hard to truly brick this device. Even if the screen remains black, there's still hope.
Once that the battery issue has been dealt with, you can move on:
Download the latest Flashtool and the proper global firmware (FTF-file) for your device from here:
http://forum.xda-developers.com/show...ight=flashtool
1: Extract/Install the Flashtool to a folder of your liking.
2: Copy the ftf-file to the "firmware" folder in the Flashtool folder you just created above.
3: Start Flashtool. Click the Bolt icon (flash). A Window appear. There, choose "flashmode". Cllick OK.
4: A new window appears. In the list on the left, choose the Generic firmware you downloaded and copied into the "firmware" folder. Should have a similar name as the file itself. (Or manually open the ftf-file from the "..." icon on the top right.)
5: Hit "OK. Follow the instructions you get on the screen:
1 - Unplug the device.
2 - Power off the device. (Unplug and replug the battery to be sure it really off, and not stuck in black screen)
3 - Press the "back" putton, and hold it down while performing the next task.
4 - Plug the device into the computers USB.
Click to expand...
Click to collapse
Forced flashing should now start.
Click to expand...
Click to collapse
time to accept the fact that it is really brick
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
mooving said:
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
Click to expand...
Click to collapse
yeah i guess so.
I just needed this closure i'll send it to service today
Hello,
I have a small question concerning this phone.
When the phone is totally switched off, will it boot when you plug the usb cable for charging ?
I'm looking for this feature
And other question : is it usable in France with 3G (there is no 4G yet here)
Thanks
My Atrix boots up but only goes to a screen where it shows the battery charging. And i'm sure there's a way to change the radios for that, you would just have to flash something for it. Hope this helped, first post ever!
Thanks for your answer
strange beacuse here some people say it's booting into phone mode when charging : http://forum.xda-developers.com/showthread.php?t=1209918
I haven't found a way to do that yet...
i have also these problems when i change the rom of atrix 4g ...have u change the original rom to custom rom ....may be this is because of custom rom...try to install official rom
I had install a new ROM and a new CWM
But I'm very curious so i touch to "wipe battery stat", now my baterry doesn't recharche and it still 23% and continues to decrease
What can I do?
sorry for my bad english, i'm french
If it's Stock based ROM, it happens, a common bug. Try restarting your phone after charging a bit. If not, try pulling the battery out and back in.
Thanks but i already try this, and he do the same thing.
So I diside to flash one of my backup and now,
ALLELUIA He works good
This problem is already solved please ignore this and solution is below if someone is facing something similar. Thank You.
Let me tell you what exactly happened so you can tell me what is the exact problem.
Problem started when i changed my SIM card. After changing my SIM card my phone was always showing 100% battery and after a day or more sudden death of battery. Then i try to recharge it back by plugin the charger in phone off mode. First i thought my battery is OK just i have to wipe battery states and everything will be fine. So i did wipe of battery states like 100 times no change.
Then i thought may be i need to re install the OS so i did that but no change and i always noticed that every time when my goes off since it shows me 100% battery every time, my battery backup was less.
So i thought my battery is drains so fast, maybe there is some problem in my battery so i should replace it. But it tried my battery in my friend's neo V and it's working fine in his mobile showing right percentage and everything so now i want to put original GB firmware so i started installing the firmware but i think because of low battery installation process was stuck at 4% so finally i removed the cable while installation was still on now it is not even recharging in phone off mode when i connect cable to mobile (LED shows nothing). And now i can see red blinking LED when i connect cable. I think phone is all dead now.
So please guys help me what should i do ?
I solved this problem by putting battery out and in again i was able to enter into flashmode and i installed .62 firmware and finally its charging hopefully my battery is OK.
Buddy thatz kernel problem use any other kernel like lupus, suave or any other it will be fyn.. Problem is in night elf kernwl and alliance kernel so din worry ur phn battery all ok..!
Assuming uh have mt 11i (neo v)