Related
my x10 die suddenly, there was 94% battery left, not plugged out long, few hrs later notice phone was off,and it will not power on again, press power to try to turn it on all it does is vibrate and that's it.
tried to flash stock 2.1 back on but not sure if it did anything, took over night or flash tool to finish, still no boot after that, press power and it vibrates that's all, sometimes it doesn't even vibrate, battery is good, works fine in another x10, put a fully charge battery in it and same result.
anyone know what happened to it?
was running eternity 3a rooted with DT.
I'm going to have to send that in for warranty, hope they won't find anything on it and void the warranty.
Was the phone quite hot at the time or heating up when trying to boot?
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
sharathx10 said:
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
Click to expand...
Click to collapse
That usually does the trick. Unplug battery for 1 minute, reinsert it and try again.
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
do you have a SD card inside. Might be a bad SD card try taking it out and booting it. Happened to me before.
blagus said:
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
Click to expand...
Click to collapse
Hi, just wanted to jump in and ask a few questions about this situation.
Do you always experience this issue? How long before it freezes? What "act" are you doing to prevent freezing? Does the phone work normally afterwards?
Hope you can help me out with some answers, I want to look into this.
instead of starting a new thread,i'll post here..
i have this restart problem..
Before this i try to fix my friend X10.. after many tries and a month acctually,i give up..
Now one more of my friend gave me another X10 which have the same problem..
Problem:
The phone will boot but after several minutes it will auto shut down and when i try to power up no vibrate and stuck at black screen.
when i pull the battery out and on again it vibrate and boot.just after boot animation it will shut down again..
Solution that i have tried so far:
Update with SEUS.
Send to profesional phone service to downgrade to 1.6.
Upgrade/flash with flash tool with GENERIC
Upgrade/flash with flash tool with X10_1.0_SE_StockRom_MultiTouch
Wipe user data in flash tool & x recovery
after several tries i got it work and i root and install x recovery.
Flash from xrecovery with custom rom Eternity.build003a.signed
format memory card.
Change battery.
All the solution i've tried doesn't make the problem dissappear.
anyone have ideas or solution?
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
I had a recent soft bricked due to some "unknown" problems which I couldn't figure out.
Anyways,I was able to boot into download mode and successfully flashed the stock jellybean firmware via Odin.
Now the problem is that my battery is empty and the phone is stuck on an what I think is an "Empty Battery Bootloop" was the battery icon blinking every 5 seconds or so.
Any ideas how to revive it ?
PS : I am unable to boot into recovery as well.
I have attached a screenshot of the issue I am facing.
Ur screenshot says... 404 error
Re-linked.
Maybe something went wrong while you were flashing the ROM via odin. First of all did you tick Only the right options while flashing in odin?
Supposing you did,
1. Maybe the ROM file which holds information for your battery might be facing curroption.
2. Maybe the kernel (the default one coming with the stock ROM) was not flashed properly.
In either case, I would suggest trying to boot into download mode and try to flash the whole thing all over again. If the problem persists, flash a different kernel/ROM or both.
II'm pretty sure that should fix the problem though.
Sent from my GT-I9100
Tried flashing via Odin for like three consecutive days.Still no luck.
I have googled it and found out that some users were facing the same problem when their battery was completely empty and the phone wont start because it didnt had enough juice to boot up.You know how to solve that problem?
Tried flashing via Odin for like three consecutive days.Still no luck.
I have googled it and found out that some users were facing the same problem when their battery was completely empty and the phone wont start because it didnt had enough juice to boot up.You know how to solve that problem?
antechx said:
Tried flashing via Odin for like three consecutive days.Still no luck.
I have googled it and found out that some users were facing the same problem when their battery was completely empty and the phone wont start because it didnt had enough juice to boot up.You know how to solve that problem?
Click to expand...
Click to collapse
Just keep it on charging wid 0.7mA or a 1mA charger for few hrs... if still it doesnt work..use a usb cord to charge via lappy...
Also use someone else's battery to boot up... and make a wipe data via stock recovery
Charged with USB for about 4-5 Hours.I cant get hold of a 1mA charger here.Using another battery is nearly impossible for me since none of my friends seem to have a S2.
Any other phone which has a battery identical to ours? (Or a Samsung phone with 4 pins possibly.)
Charged with USB for about 4-5 Hours.I cant get hold of a 1mA charger here.Using another battery is nearly impossible for me since none of my friends seem to have a S2.
Any other phone which has a battery identical to ours? (Or a Samsung phone with 4 pins possibly.)
Nope. Don't try a battery not designed for the device. Asking for trouble.
Time to change it with a new battery or hook up with an external charger?
PS : Took it to a local mobile repair shop and asked for a universal battery charger.
When I gave him the battery,the first thing he asked was if the phone ever got wet.
He said there's some I don't know what on the battery due to licking it.
I recently replaced the charging circuit from a trusted Samsung shop and he says it's totally fine.
Seems like some kind of corrosion on the battery.Any ideas on how to remove it ?
Anyone ?
hi
i have xperia Go, recently I was changing its rom from stock rom to CM11, i followed all the steps that were mention in tutorial and as i restart my cell phone it wont turn on, even the sony logo is not showing, it just flashes the status LED in white one time, vibrates and blank.. I tried many tutorials but nothing works and battery discharged, now my cellphone is not even charging the battery, i've tried with all the ways even i open up the cell phone took the battery out and try to charge it with some diff battery but its not getting charged, I think there is a different way to charge it, please
Please help me just that I could charge my cell phone and recover it, please reply me soon..
Thank you
Regards
hawk_waleed said:
hi
i have xperia Go, recently I was changing its rom from stock rom to CM11, i followed all the steps that were mention in tutorial and as i restart my cell phone it wont turn on, even the sony logo is not showing, it just flashes the status LED in white one time, vibrates and blank.. I tried many tutorials but nothing works and battery discharged, now my cellphone is not even charging the battery, i've tried with all the ways even i open up the cell phone took the battery out and try to charge it with some diff battery but its not getting charged, I think there is a different way to charge it, please
Please help me just that I could charge my cell phone and recover it, please reply me soon..
Thank you
Regards
Click to expand...
Click to collapse
Try flashing the stock ftf file using flashtool. At least this way you will have a working phone. Then you can figure out flashing CM11 again.
My battery percentage stucks at mostly 97% to 99% never goes full charge, thou ampere sees it as fully charged on 97% or %98. How can i fix this thing? Without opening the hardest back cover in the century of smartphones.
Edit: Tested with RR Oreo 6.1.0 07231028 build and it went up to 100% fully without single interruption. But on MIUI it never goes beyond 97% i have to replug and unplug the cable several times to get it to 99%.
Same ..bt i changed rom bt nothing happned.what can i do
same with mine. Before Im using AOSP rom then I revert back to Masik U 2.5. I need to power off to reach 100% if not its always 98% and plug and unplug.
Thanks
How u fix this
After switching from miui 10 to miui 9 i had this problems: battery never full charge, phone gets hot while charging, at 15% left jiuce phone switches off. I tryed to clean all and flash, i even relocked bootloader it fixed it temporary.
So I called service, guy told me that when you go back with os version sometimes drivers go bad, sometimes wifi, battery, signal, etc. He told me to send him a device and he will try to fix this. I sent him and he fixed it. Btw i noticed that it was installed miui 9.2.6.0 NEGMIEK. He didnt told me what he did but you can try to flash this version of miui maybe it will fix.
It looks like MIUI based misreading or like the reply #3 said maybe driver issue. I'm upgrading my device to MIUI 10 8.8.30 to see if it fixes this thing up. If not i'll have to sadly request assistance..
bdogan1912 said:
My battery percentage stucks at mostly 97% to 99% never goes full charge, thou ampere sees it as fully charged on 97% or %98. How can i fix this thing? Without opening the hardest back cover in the century of smartphones.
Edit: Tested with RR Oreo 6.1.0 07231028 build and it went up to 100% fully without single interruption. But on MIUI it never goes beyond 97% i have to replug and unplug the cable several times to get it to 99%.
Click to expand...
Click to collapse
When on miui 9/10, root it, install a root explorer then go to data/system. There will be two or three files named batterystats.bin, batterystatsdaily.xml and one other file (can't remember the name as I am using Masik 2.5 and it doesn't have these files). Just delete them after your phone charges to 97 or 99 % , close all background apps and again plug in the charger and check if it goes to 100%......
I tryed that before, it will give temporary fix, even reflashing 9.5.6 miui didnt help, better ask for assistance they have another tools for flashing roms. Guy from service told me before that he dont need unlocked bootloader to flash rom. Becouse i told hom that i relocked bootloader and i have to wait 360 hours to relock again. Sorry for bad english.
daca0 said:
I tryed that before, it will give temporary fix, even reflashing 9.5.6 miui didnt help, better ask for assistance they have another tools for flashing roms. Guy from service told me before that he dont need unlocked bootloader to flash rom. Becouse i told hom that i relocked bootloader and i have to wait 360 hours to relock again. Sorry for bad english.
Click to expand...
Click to collapse
Yean, there is no need for unlocked bootloader to flash stock miui rom. They use EDL mode to flash the rom which automatically locks the device. You can try this method on your own only if you know what to do or else go to the service centre...
download terminal app from google play store (like Terminal Emulator for Android)
or
if you have orangefox twrp, go in ADVANCED - TERMINAL
and type
Code:
su
rm /data/system/battery*
alternatively, you can use file manager from orangefox
after you have to turn off the smartphone
Open the phone and remove battery for a while, and plug in again....
this definitely fix the problem...
I have a same problem
But I have a solution
Try one time charge don't disconnect a cable while charging
Battry gets 100% charged
Did anybody find any solution for this? I tried everithing, but on MIUI it doesn't charge up fully. It stucks at 97%. And it won't charge further even after a power off.
minikahona said:
Did anybody find any solution for this? I tried everithing, but on MIUI it doesn't charge up fully. It stucks at 97%. And it won't charge further even after a power off.
Click to expand...
Click to collapse
My solution was to disconnect battery from motherboard for 5 minutes and connect it back. I didnt turned phone on, just connected charger (green battery only on screen)
This should help.
If you dont want to dissasemble your phone, calibrate your battery with root and app. But first discharge it to 0% and plug charger and turn it on. From 0% it should charge 98% or 100%. If 100% shows you can be free, if 98% shows try method with app.
Good luck!
skrubxgt said:
My solution was to disconnect battery from motherboard for 5 minutes and connect it back. I didnt turned phone on, just connected charger (green battery only on screen)
This should help.
If you dont want to dissasemble your phone, calibrate your battery with root and app. But first discharge it to 0% and plug charger and turn it on. From 0% it should charge 98% or 100%. If 100% shows you can be free, if 98% shows try method with app.
Good luck!
Click to expand...
Click to collapse
Thank you for your reply. I already tried the 0 to 100% but unfortunately it doesn't wotk. It only reach 97%. Someboy mentiond in this thread that they reached 100 on cutom roms and this is what my phone does too. I tried the unofficial pixel experience pie rom, and my phone reached 100%. But when i reverted back to stock, or xiaomi.eu it only charge till 97%. I don want to take it apart, so I think that's it. I have to live with it.
Got the same issue on mine.
Only charge to 96% when the phone is on and 97% when the phone is off.
Same issue on Miui 10 global and EU 8.12.27.
Besides opening the phone to unplug the battery, had anyone tried to flash via fastboot miui 9 again?
On miui 9 i didn't had this issue.
Later i will try to flash miui 9.5.11.0 via fastboot to see if it fix the issue and report back.
Thanks.
Edit: tried 9.5.11.0 same result.
Will try now pixel experience official and unnoficial
I have a probelm too
My mobile battery stuck on 97%
How to fix it