hi
i have xperia Go, recently I was changing its rom from stock rom to CM11, i followed all the steps that were mention in tutorial and as i restart my cell phone it wont turn on, even the sony logo is not showing, it just flashes the status LED in white one time, vibrates and blank.. I tried many tutorials but nothing works and battery discharged, now my cellphone is not even charging the battery, i've tried with all the ways even i open up the cell phone took the battery out and try to charge it with some diff battery but its not getting charged, I think there is a different way to charge it, please
Please help me just that I could charge my cell phone and recover it, please reply me soon..
Thank you
Regards
hawk_waleed said:
hi
i have xperia Go, recently I was changing its rom from stock rom to CM11, i followed all the steps that were mention in tutorial and as i restart my cell phone it wont turn on, even the sony logo is not showing, it just flashes the status LED in white one time, vibrates and blank.. I tried many tutorials but nothing works and battery discharged, now my cellphone is not even charging the battery, i've tried with all the ways even i open up the cell phone took the battery out and try to charge it with some diff battery but its not getting charged, I think there is a different way to charge it, please
Please help me just that I could charge my cell phone and recover it, please reply me soon..
Thank you
Regards
Click to expand...
Click to collapse
Try flashing the stock ftf file using flashtool. At least this way you will have a working phone. Then you can figure out flashing CM11 again.
Related
my x10 die suddenly, there was 94% battery left, not plugged out long, few hrs later notice phone was off,and it will not power on again, press power to try to turn it on all it does is vibrate and that's it.
tried to flash stock 2.1 back on but not sure if it did anything, took over night or flash tool to finish, still no boot after that, press power and it vibrates that's all, sometimes it doesn't even vibrate, battery is good, works fine in another x10, put a fully charge battery in it and same result.
anyone know what happened to it?
was running eternity 3a rooted with DT.
I'm going to have to send that in for warranty, hope they won't find anything on it and void the warranty.
Was the phone quite hot at the time or heating up when trying to boot?
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
sharathx10 said:
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
Click to expand...
Click to collapse
That usually does the trick. Unplug battery for 1 minute, reinsert it and try again.
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
do you have a SD card inside. Might be a bad SD card try taking it out and booting it. Happened to me before.
blagus said:
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
Click to expand...
Click to collapse
Hi, just wanted to jump in and ask a few questions about this situation.
Do you always experience this issue? How long before it freezes? What "act" are you doing to prevent freezing? Does the phone work normally afterwards?
Hope you can help me out with some answers, I want to look into this.
instead of starting a new thread,i'll post here..
i have this restart problem..
Before this i try to fix my friend X10.. after many tries and a month acctually,i give up..
Now one more of my friend gave me another X10 which have the same problem..
Problem:
The phone will boot but after several minutes it will auto shut down and when i try to power up no vibrate and stuck at black screen.
when i pull the battery out and on again it vibrate and boot.just after boot animation it will shut down again..
Solution that i have tried so far:
Update with SEUS.
Send to profesional phone service to downgrade to 1.6.
Upgrade/flash with flash tool with GENERIC
Upgrade/flash with flash tool with X10_1.0_SE_StockRom_MultiTouch
Wipe user data in flash tool & x recovery
after several tries i got it work and i root and install x recovery.
Flash from xrecovery with custom rom Eternity.build003a.signed
format memory card.
Change battery.
All the solution i've tried doesn't make the problem dissappear.
anyone have ideas or solution?
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
gonix said:
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Click to expand...
Click to collapse
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Screen-shots are from the old PC Companion, byt they still looks very much like them in the new version
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Emperor.dk said:
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
Click to expand...
Click to collapse
Oh I know someone who has the same x10 with me. I guess Ill have to try your suggestion.
SmG67 said:
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Click to expand...
Click to collapse
It doesnt help because when Im in the part where it says, press the back button while inserting the usb, the phone cannot be detected and so the update cannot continue.
This problem is already solved please ignore this and solution is below if someone is facing something similar. Thank You.
Let me tell you what exactly happened so you can tell me what is the exact problem.
Problem started when i changed my SIM card. After changing my SIM card my phone was always showing 100% battery and after a day or more sudden death of battery. Then i try to recharge it back by plugin the charger in phone off mode. First i thought my battery is OK just i have to wipe battery states and everything will be fine. So i did wipe of battery states like 100 times no change.
Then i thought may be i need to re install the OS so i did that but no change and i always noticed that every time when my goes off since it shows me 100% battery every time, my battery backup was less.
So i thought my battery is drains so fast, maybe there is some problem in my battery so i should replace it. But it tried my battery in my friend's neo V and it's working fine in his mobile showing right percentage and everything so now i want to put original GB firmware so i started installing the firmware but i think because of low battery installation process was stuck at 4% so finally i removed the cable while installation was still on now it is not even recharging in phone off mode when i connect cable to mobile (LED shows nothing). And now i can see red blinking LED when i connect cable. I think phone is all dead now.
So please guys help me what should i do ?
I solved this problem by putting battery out and in again i was able to enter into flashmode and i installed .62 firmware and finally its charging hopefully my battery is OK.
Buddy thatz kernel problem use any other kernel like lupus, suave or any other it will be fyn.. Problem is in night elf kernwl and alliance kernel so din worry ur phn battery all ok..!
Assuming uh have mt 11i (neo v)
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
Press and hold power button for 30 seconds, then release power button
Then connect your mobile with pc/laptop
Let it be charged for an hour
Then reboot it into fastboot and flash stock lollipop
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
mklkumar4 said:
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
Click to expand...
Click to collapse
Hey, thanks for your help.
I know how to enter into fastboot mode and all that stuff... but when I try to turn on my device, nothing happen, and if I connect my Moto E to the PC the device manager detects it as: qhsusb_bulk
It appears that the boatloder corrupted itself for some reason, a lot of people have the same issue.
I think it is hardbricked, but if you have some info that could help me, I'd be grateful
1st try to unlock bootloader if you are not able to do that, try to flash stock firmware this may help you
And please send screenshots of all the stuff that you can access in ur bricked device...! It will be helpful for me to understand