Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
Press and hold power button for 30 seconds, then release power button
Then connect your mobile with pc/laptop
Let it be charged for an hour
Then reboot it into fastboot and flash stock lollipop
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
mklkumar4 said:
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
Click to expand...
Click to collapse
Hey, thanks for your help.
I know how to enter into fastboot mode and all that stuff... but when I try to turn on my device, nothing happen, and if I connect my Moto E to the PC the device manager detects it as: qhsusb_bulk
It appears that the boatloder corrupted itself for some reason, a lot of people have the same issue.
I think it is hardbricked, but if you have some info that could help me, I'd be grateful
1st try to unlock bootloader if you are not able to do that, try to flash stock firmware this may help you
And please send screenshots of all the stuff that you can access in ur bricked device...! It will be helpful for me to understand
Related
I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???
brick is normal!
you should donate the brick to xda-developers now!
What you mean is normal ? is their anyway way i can get it fixed or is it just a paper weight now ?
probably runed out of battery. you should charge the battery in some way. try to power on the device while pressing camera button. it should show a boot loader screen. the you should flash a G4 SAFE ROM (with no spl/ipl) like "wizard love". if that doesnt help, sorry mate, you have a brick
are you able to enter bootloader?
hold down camera and either press power or reset button
No im not able to do anything on the phone lastnight it would go into bootloader randomly evey now and again but it isnt doing nothing now.
Ugh , i hope it is just the battery if it isnt then theirs nothing i can do for the phone unless i can get it in to bootloader mode right ?
your battery is dead...that's why you can't enter bootloader.
Moving to wizard G4.
Only the original charger is capable to charge your battery (it has a little bit more power), if it's fully charged... go into bootloader mode and install your official ROM the normal way.
It worked for me.
correct
im dealing with the same issue and my battery isnt dead
tasky smokey newbie bricks!! yomy !!
charly_mx said:
tasky smokey newbie bricks!! yomy !!
Click to expand...
Click to collapse
That's not very encouraging and nice thing to say.We all came here as newbies,not a big deal.
We all hate to see a guy loose his device like this,after all it's a developer's forum,we shud be atleast concerned and help out,if we can.
Hope you two be able to get your devices working again soon.
Good luck
Fixed
I just wanted to thank everyone for your help , i got my new battery in yesterday and my phone booted up flashed back to at&t orginal rom. Thank So Much.....
Hey guys i've a problem with my x10
So one night i was playing with it than the other day the phone would start
so i thought yeah right might be the battery or something. i took it to my friends x10 it was with 87% charged so i exclude this
Than i tried to flash with flashtool a new kernel and i get stuck at 9% or 15% depending on the kernel i use.
With SEUS it starts to repair but it says. No new updates avaiable after a few moments.
Some information regarding my phone
Unlocked Bootloader
FXP KERNEL
MM TEAM MIUI V4
The phone vibrate but doesn't start or load the kernel.
What do i do?!
Srry for my bad english
Thx in advance
Usrle flashtool to reflash kernel or firmware.
already did but i get stuck at 9% or 15% flashing the kernel
I'm downloading a full generic rom x10a
having similar problem
Hi, I had similar problem as well
X10i running FXP CM7 suddenly just wont boot n charge after I turn off the phone
it wont boot after flashing anything (firm or kernel) except the official firm
now that I end up with a cap R bootloader but flashtool claim that bootloader is rooted
do I still keep the bootloader unlock?
i guess you have a locked bootloader since the original firmware is loading just fine even tho rooting has nothing to do with the bootloader it self. i'm only guessing.
I'm stuck at. Flashing Loader
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
[XBOCT]™ said:
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
Click to expand...
Click to collapse
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
same problem repeat
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
mooving said:
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
Click to expand...
Click to collapse
i'm using
X10a_2.1update1_r2.1.A.0.435_Generic.ftf
And it get stuck at Flashing loader
Idk but i can "read" the kernel when i dump the propriets but i can't "right" when i try to flash something
Anyone?
guys?
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
LJE said:
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
Click to expand...
Click to collapse
maybe i'm wrong idk maybe is a soft brick. thats why i'm asking for some help.
almomdegal said:
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
Click to expand...
Click to collapse
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Try wotanserver's flashtool...
http://www.wotanserver.com/en/
Good luck
SysGhost said:
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Click to expand...
Click to collapse
Didn't work, i even use my friends battery to flash it and it didn't work
almomdegal said:
Didn't work, i even use my friends battery to flash it and it didn't work
Click to expand...
Click to collapse
Well, if the battery issue was fixed, and you're sure the battery is fully charged, then try this: (Quoting from my other post)
I've charged/replaced the battery, and are having trouble with starting up. Earlier flash failed. Now what?
Don't worry. It's pretty darn hard to truly brick this device. Even if the screen remains black, there's still hope.
Once that the battery issue has been dealt with, you can move on:
Download the latest Flashtool and the proper global firmware (FTF-file) for your device from here:
http://forum.xda-developers.com/show...ight=flashtool
1: Extract/Install the Flashtool to a folder of your liking.
2: Copy the ftf-file to the "firmware" folder in the Flashtool folder you just created above.
3: Start Flashtool. Click the Bolt icon (flash). A Window appear. There, choose "flashmode". Cllick OK.
4: A new window appears. In the list on the left, choose the Generic firmware you downloaded and copied into the "firmware" folder. Should have a similar name as the file itself. (Or manually open the ftf-file from the "..." icon on the top right.)
5: Hit "OK. Follow the instructions you get on the screen:
1 - Unplug the device.
2 - Power off the device. (Unplug and replug the battery to be sure it really off, and not stuck in black screen)
3 - Press the "back" putton, and hold it down while performing the next task.
4 - Plug the device into the computers USB.
Click to expand...
Click to collapse
Forced flashing should now start.
Click to expand...
Click to collapse
time to accept the fact that it is really brick
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
mooving said:
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
Click to expand...
Click to collapse
yeah i guess so.
I just needed this closure i'll send it to service today
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Veesais said:
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Click to expand...
Click to collapse
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
ParanoidKang said:
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
Click to expand...
Click to collapse
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Veesais said:
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Click to expand...
Click to collapse
Now the screen may not show, but try booting into fastboot mode by press and hold the Trackball+Power buttons together.
I'm not sure about the nexus one, but newer nexus devices have factory images, supplied by Google. If they exist for the nexus one, you should be able to save your device by flashing them through fastboot. That is if the images exist and you can get to fastboot.
Sent from my Nexus 4 using XDA Premium 4 mobile app
I got a P9000 in the late spring, and have been really happy with it. Unfortunately I dropped it on the ground, and the screen cracked, after which the touch function did not work (but the phone did) I finally managed to get a new screen from China, and it has been installed by a local shop dealing with mobiles. However, the shop told me they could/would not deal with anything else but changing the LCD screen. The phone switches on (I can hear starting jingles and emails downloading etc) but the screen just turns from black to dark blue and stays that way. I have been trawling through the forums, but not sure what to do next. Take it that I need to flash it, and have followed the instructions given here, but it just seems to time out. Anyone got the patience to walk me through this?
UKrugger said:
I got a P9000 in the late spring, and have been really happy with it. Unfortunately I dropped it on the ground, and the screen cracked, after which the touch function did not work (but the phone did) I finally managed to get a new screen from China, and it has been installed by a local shop dealing with mobiles. However, the shop told me they could/would not deal with anything else but changing the LCD screen. The phone switches on (I can hear starting jingles and emails downloading etc) but the screen just turns from black to dark blue and stays that way. I have been trawling through the forums, but not sure what to do next. Take it that I need to flash it, and have followed the instructions given here, but it just seems to time out. Anyone got the patience to walk me through this?
Click to expand...
Click to collapse
I am facing same thing here. The screen is not coming up at all, But I can hear sound too. ANyone else who has changed the screen successfully before?
yes, i changed the screen successfully. After screen replacement i flashed the newest rom with flashtools and all was ok.
DonMagnifico said:
yes, i changed the screen successfully. After screen replacement i flashed the newest rom with flashtools and all was ok.
Click to expand...
Click to collapse
Can you describe the precise process you followed. I seem to get stuck when I try to flash the phone
UKrugger said:
Can you describe the precise process you followed. I seem to get stuck when I try to flash the phone
Click to expand...
Click to collapse
skeleton1911 describe in this thread how to flash the P9000:
http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
in this thread from skeleton1911 you find all links to the needed files:
http://forum.xda-developers.com/showpost.php?p=66784596&postcount=146
change screen start logo screen after light on/off all the time 2sec
DonMagnifico said:
skeleton1911 describe in this thread how to flash the P9000:
http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
in this thread from skeleton1911 you find all links to the needed files:
http://forum.xda-developers.com/showpost.php?p=66784596&postcount=146
Click to expand...
Click to collapse
hello, thank you for you help. i've change the screen p9000 and when i put battery the screen logo elephone turns on and turns off two second always.is it normal and is it essential new flash when you put a new screen. in periph manager i see two second USB Vcom MT 65xx preloader but it's disapear 2seconde all the time because logo elephone light on and off two second. If you give me a solution, you are the best.
the pc don't recognize telephone of course. but i'm tm trying your methode but i've meet difficult with install pilot.
thank you XDA
thank you to help me, all the day i'm trying solutions,after the screen change, Flashtool tell sucess download, but it continues to turn on and off with the logo elephone starts. in peripheral it appears and disappears every two seconds. i don't know if there is a room in my phone. how to inject the files in the phone with a Peripheric always on and off. help me please. after flashtool ok download the screenis black and nothing i move battery and after logo elephone on/off but nothing else. someone know the reason on/off and appear an desappear in device : Mt65xx USBVCOM.
tanguy66 said:
hello, thank you for you help. i've change the screen p9000 and when i put battery the screen logo elephone turns on and turns off two second always.is it normal and is it essential new flash when you put a new screen. in periph manager i see two second USB Vcom MT 65xx preloader but it's disapear 2seconde all the time because logo elephone light on and off two second. If you give me a solution, you are the best.
the pc don't recognize telephone of course. but i'm tm trying your methode but i've meet difficult with install pilot.
thank you XDA
Click to expand...
Click to collapse
You are in a boot loop. This is not a bad sign, now you know the screen works. It's normal that you have to flash the Rom again after replacing the screen. if you use flashtool, start download in flashtools before you connect your phone to the PC, then hold vol+ on your P9000 and connect the phone to the pc.
DonMagnifico said:
You are in a boot loop. This is not a bad sign, now you know the screen works. It's normal that you have to flash the Rom again after replacing the screen. if you use flashtool, start download in flashtools before you connect your phone to the PC, then hold vol+ on your P9000 and connect the phone to the pc.
Click to expand...
Click to collapse
always the same problem: light on off all 2 seconds, with B+vol+ i see recovery 1 seconde. i haven't the time to do something. question is it possible the battery bad, the logo flash all the time if the battery bad the logo don't go isn't it. please help i'm trying plenty solution but no good . thank you.
tanguy66 said:
always the same problem: light on off all 2 seconds, with B+vol+ i see recovery 1 seconde. i haven't the time to do something. question is it possible the battery bad, the logo flash all the time if the battery bad the logo don't go isn't it. please help i'm trying plenty solution but no good . thank you.
Click to expand...
Click to collapse
no, it's not the battery. You made a mistake by flashing the rom, now you are in a boot loop. Ignore the message on the screen. Try to flash the rom again. start flashtool, select the scattertext, click download, hold vol+ button on the phone and connect the phone to the PC
PLEASE HELP me, can you give me a solution to start up the phone again
hello , before flash tool all is ok flashing GOOD, now it's more bad now i have no lignt no logo, and when use flash tool always stop download 20% BROM error: status dowwnload exeption (0xc0050003) (HINT) : , i don't know if i have a good battery
yesterday i have a new image appears it'a big beautiful battery only one bar after logo several times. i'm found an d try all solutions, 4 days , i sleep at 1 oclock. help to find a solution. how to know or test if the telephone is dead or little life.
OK now i arrived with flash tool i begin all zero, and message OK Good, i'm verry worried, no light , no logo??have you a solution to know if the battery now? thank you help.
do you know when the message tell OK,it means all things an room is now ok in the phone. I'm not sure
just now i'm testing battery with tester 3v 1ma it's good. how to do to light screen now. it's strange.
and with electric power it must work normaly ,or not if the battery dead?
i think you flashef the wrong preloader. flash the phone again with the newest firmware. in #5 you find a link to the needed files.
DonMagnifico said:
skeleton1911 describe in this thread how to flash the P9000:
http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
in this thread from skeleton1911 you find all links to the needed files:
http://forum.xda-developers.com/showpost.php?p=66784596&postcount=146
Click to expand...
Click to collapse
After a couple of tries, I did manage to get this working. Initial failure seemed to be me not pressing the "Vol +" button. Thanks very much for your help
DonMagnifico said:
i think you flashef the wrong preloader. flash the phone again with the newest firmware. in #5 you find a link to the needed files.
Click to expand...
Click to collapse
thank you. i use flash tool v5.1620. i have windows 7 32 bit,mtk 65 vcom is update, i'm not sure what do you mean. newest firmware. i have last room for p9000. can you tell more details please or more link to succeed. i read, and i trying a lot, now i swimming again.
UKrugger said:
After a couple of tries, I did manage to get this working. Initial failure seemed to be me not pressing the "Vol +" button. Thanks very much for your help
Click to expand...
Click to collapse
ok , i don't understand with flash tool i have plenty of time a big download is ok, if the download is ok why it's doesn't working.
the phone is often remains dark. I put in charge the battery with two 2mn special machine at my work , and it's wake up the phone souddenly appears again the elephone logo and battery with 1 once bar, I don't know if it's me or the battery or something else. normally if I plug in USB i must have lignt Electric power? but nothing.
thank you and not let me down please i need you.
tanguy66 said:
ok , i don't understand with flash tool i have plenty of time a big download is ok, if the download is ok why it's doesn't working.
the phone is often remains dark. I put in charge the battery with two 2mn special machine at my work , and it's wake up the phone souddenly appears again the elephone logo and battery with 1 once bar, I don't know if it's me or the battery or something else. normally if I plug in USB i must have lignt Electric power? but nothing.
thank you and not let me down please i need you.
Click to expand...
Click to collapse
Sorry, I can' t help you more. All I know i telled you. But write a private message to skeleton1911, he has a great experience in reactivating Phones. May be he can help you.
P9000 screen replacement
Hi . I had my p9000 about 2 months when I sat on it and cracked the screen,the casing was very slightly curved so I gave it to a shop to repair,now nearly 2 months later they say they can't get it to start up. They tried a new battery and I told them what I'd read on this forum regarding flahing the rom but They gave me back the phone with a new screen and nothing else, so I told them i'm not paying for 1/2 a repair and told them to remove the new screen and give me back the phone as it was . What do you think could be the problem if a repair shop cannot repair a screen and install new sorftware is there hope for it?
Hi, i broked my screen again so i am not a newbie about this... but this time after flashing the Phone show nothing at all... the small LED Dot is shining when android is boot, so i dont think the cable is connected wrong. The touch works fine..What can it be??
Hy, Guys.
first i want to say
Sorry for my English i am from Austria. so my first Language is German.
and also sorry for a second post,
but no one write me back so i thought i post my problem here again!!!!
My LG G4 H815 runs with Genesys 4.8 or 4.6.(dont know anymore) Bootloader Unlocked.
a few Days ago i had only 8% Battery so i put my Power cable in the device and go to sleep.
Next day i want to start my Phone an...........
NOTHING.
my G4 is Dead!!!!
i dont get it.
i try´d to start norm.
nothing.
put out the battery, put it back, try to start but
NOTHING...
Tryed to boot in Recovery but also NOTHING.
I tryed to power my Phone on without battery and Power Cable but no life sign.
no LED or Display Light goe´s on.
Now i put my G4 with usb on the Laptop but it did not reconize the Phone.
PLEASE GUYS PLEASE HELP ME.
I UNLOCKED MY BOOTLOADER!!!
And now i think my WARRANTY is gone.
I think the repair cost´s are verry high or do somebody know if LG Repair my PHone for free with unlocked BOOTLOADER???
sorry guys but i am done.
my nervs are gone..
If someone could help me that would be AMAZING and i could pay a few BEER´s-:fingers-crossed::good:
Thanks
Does the led blinks while charging(if this device has a led)
Regards milkyway3