I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???
brick is normal!
you should donate the brick to xda-developers now!
What you mean is normal ? is their anyway way i can get it fixed or is it just a paper weight now ?
probably runed out of battery. you should charge the battery in some way. try to power on the device while pressing camera button. it should show a boot loader screen. the you should flash a G4 SAFE ROM (with no spl/ipl) like "wizard love". if that doesnt help, sorry mate, you have a brick
are you able to enter bootloader?
hold down camera and either press power or reset button
No im not able to do anything on the phone lastnight it would go into bootloader randomly evey now and again but it isnt doing nothing now.
Ugh , i hope it is just the battery if it isnt then theirs nothing i can do for the phone unless i can get it in to bootloader mode right ?
your battery is dead...that's why you can't enter bootloader.
Moving to wizard G4.
Only the original charger is capable to charge your battery (it has a little bit more power), if it's fully charged... go into bootloader mode and install your official ROM the normal way.
It worked for me.
correct
im dealing with the same issue and my battery isnt dead
tasky smokey newbie bricks!! yomy !!
charly_mx said:
tasky smokey newbie bricks!! yomy !!
Click to expand...
Click to collapse
That's not very encouraging and nice thing to say.We all came here as newbies,not a big deal.
We all hate to see a guy loose his device like this,after all it's a developer's forum,we shud be atleast concerned and help out,if we can.
Hope you two be able to get your devices working again soon.
Good luck
Fixed
I just wanted to thank everyone for your help , i got my new battery in yesterday and my phone booted up flashed back to at&t orginal rom. Thank So Much.....
Related
Ok, so I tried to flash my G4 wizard to wm6, went all the way through the flash, got to 99% and stopped, giving me a comm error. I did the recovery and im in an endless flash to 99% loop. When I turn it on, I get the bootloader (3 stripe) screen, with the following:
RUU upper right corner
IPL 2.25.0001
SPL 2.25.0001
USB lower left corner.
I have spent the last 4 hours reading posts and cannot fix this thing. Any help would be greatly appreciated.
did u flash it back to carrier rom?
Flash it back to the original carrier ROM (should be available on the website) and then use ShellTool to flash the ROM. make sure that you follow the instructions exactly, otherwise, you will end up with a bricked rom.
-Nstefanelli-
The only rom I can find on Cingular's web site, once downloaded says its corupted, and I cant find one on XDA at all. Anybody know where else I might find one?
Wizard Love rom is another one you could try.
Wizard Love got me goin again, I love me some wizard.
Thanks for the help guys!!!
Same Problem I Have Faced.... And Also Solved.
u have Radio Rom problem....
search the latest radio rom and upload to your rom... and restart your pda...
reply me..... sooon because same problem i had faced and solved also.
Same problem
I was having the same problem yesterday. Eventually i got it to work again. It was a little confusing though because i used the rom from the HTC website to get it up and running again with wm5 and then used ShellTool from the sticky in this forum to flash it with a wm6 rom. From what i gather it's because my phone was CID locked, something that none of the roms include in their instructions to watch out for. Maybe a sticky in the forum for newbs like me containing things to watch out for while flashing roms?
A side note:
I had to download the rom from the HTC site twice in order for it to flash back to the original OS. The first time i downloaded the rom i kept getting an error. I guess it was a bad download or something but the second one worked in the first shot.
think i bricked my wizard
oops !!!!
think i flashed a g3 rom onto my g4 wizard and for a while it stayed in bootloader screen (tricolour) now the wizard is dead with no charging light when plugged in and performing hard reset does nothing
please help !!!!!!!!!!!!!!!!!!!!!!
gripper said:
oops !!!!
think i flashed a g3 rom onto my g4 wizard and for a while it stayed in bootloader screen (tricolour) now the wizard is dead with no charging light when plugged in and performing hard reset does nothing
please help !!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
There is no help for you if you did flash a non-official G3 rom onto your phone.
Recent Official carrier releases are the only roms that contain bootloaders that are safe to flash into a G4. (Note older carrier releases could possibly fry your phone as well as they may not contain G4 bootloaders)
If you flashed a custom rom with IPL/SPL your device is done for good.
Though you said it went to the bootloader prior to going dark so you may just have a dead battery and a bad flash. Get a battery from a friend or buy one and then see if the device will power on. If you can't get it to power on with a known good battery then it is most likely fried. If it does boot at least to bootloader then you should be able to recover your device. Most chargers will not charge the battery of your phone unless the phone is fully booted into windows. So it is very important to have a contingency plan in case of a bad flash with these phones as playing/troubleshooting while trying to recover from a bad flash will drain your battery possibly leaving you with not enough juice to complete a flash.
hi zzan
thanks for the reply, i think your right about the battery it actually turns on for about 10 seconds now into bootloader but then the battery dies again so i gonna source a battery.
gripper said:
oops !!!!
think i flashed a g3 rom onto my g4 wizard and for a while it stayed in bootloader screen (tricolour) now the wizard is dead with no charging light when plugged in and performing hard reset does nothing
please help !!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Remove the battery for about 5 minutes, then put it back in.. then try booting in bootloader mode <tri color screen> .. then flash with an OFFICIAL Carrier ROM ..
I flashed my hermes yesterday <changing the spl and stuff> and it was dead for a little bit, until I took the battery out and put it back in.. <for some reason it was like a de-fibrilator..>
Try that.
hi madcap,
not looking good i toook it to a phone engineer and he says it is corrupt ? he has tried flashing it, apparently there is a guy who will put in a new chip ? i am such a fool i bricked my phone just to get rid of o2 stuff !!!!!
gripper said:
hi madcap,
not looking good i toook it to a phone engineer and he says it is corrupt ? he has tried flashing it, apparently there is a guy who will put in a new chip ? i am such a fool i bricked my phone just to get rid of o2 stuff !!!!!
Click to expand...
Click to collapse
A new chip?!?!??
The problem is the in the IPL area which can now be flashed only via JTAG (cable system that doesn't require booting files since it operates directly on the chip)
Take it to an official repair.
Hi,
I have almost the same problem. I tried to flash to WM6.1 for wizzard, it got to 99% and failed (connection lost). I then tried the recovery process but that didnt work.
Now I can boot to the booloader, and see the IPL/SPL versions (2.25.0001) and can see USB on the lower left. But , it is not making a connection to my PC. None of the RUU, ROMS, HardSPL, or SoftSPL apps can connect to it.
They all report some connection error, "Device not found", or "Connection Error 264"...
I have read a bunch on this forum, and tried alot of stuff but nothing worked.
I started up my own thread on my issue, but hope someone could help me, help someone else in the process here..
How can I get this thing flashable again?
Thanks
Madcap180 said:
Remove the battery for about 5 minutes, then put it back in.. then try booting in bootloader mode <tri color screen> .. then flash with an OFFICIAL Carrier ROM ..
I flashed my hermes yesterday <changing the spl and stuff> and it was dead for a little bit, until I took the battery out and put it back in.. <for some reason it was like a de-fibrilator..>
Try that.
Click to expand...
Click to collapse
This worked for me and now I can connect the apps to the phone again. But after I try to install the default rom, everytime at 80% it looses the connection again.. .
Anyone know a good WM6.1 rom that works with 8125 G4
end123 said:
This worked for me and now I can connect the apps to the phone again. But after I try to install the default rom, everytime at 80% it looses the connection again.. .
Anyone know a good WM6.1 rom that works with 8125 G4
Click to expand...
Click to collapse
Fully recharge your battery, then try to flash again. Low/dead/misreporting battery will kill a flash as surely as disconnecting the cable in mid-flash. Oh, and try WizFlo...really cool! (I had to fiddle with the Opera Browser install to get the Internet connection to work correctly, but who cares, it was worth it!)
First of all sorry for my english not good.
Start : with my HD2 have brick after task29 and not success to flash new ROM I'm take USB. cable out and try to open my HD2 in to boot loader by put volum down + power bottom but screen not show any image or 3 color my phone it only long vibration pull battery out waiting 30 minute and put battery in and try to open my phone to boot loader but is same only long vibration.
Now : can not do any think with it when try to plug power in my phone is auto startup and long vibration.
I'm search on google and in this forum not have some one face problem same as me please help me to fix this.
Any body please help me, I'm love it because now we can run both WM. and Android
Upppp waiting for your help
Did you try a long press of the reset-button?
You could try to put the original Stock Image from HTC onto the root-folder of your SD-Card, rename it to LEOIMG.nbh and Push Vol up + Vol down during start and follow the on-screen instructions if it works.
Otherwise use Search-Function in the forum.
ı have jtag HTC for samsung and HTC devices if u want send for repair to me..
www.sevgigsm.net/forum
admin..
I use ORT
Did you check to make sure your radio version was correct before flashing? This is probably the number one reason for bricking.
Check this thread it may help you if you did the flash properly:
http://forum.xda-developers.com/showthread.php?t=668347
i got same problem now...
no screen, no boot, vol down+ power oso same
no screen just a long vibration
anybody help?
I am using the correct radio so don't tell me I am using a wrong radio or something, I have been flashing for 4 months so I know EXACTLY how to flash.
now i can neither get into tri-color or hard reset so don't tell me to flash or smth like that, just tell me how to recover properly
Don't tell us to use search or something because seems like only 2 of us is encountering this problem in the internet
I'm exactly the same problem as TS coz it juz auto go vibrate when plug in battery
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
at the long vibrate, when i plug in to my pc, it will keep on got usb connected and disconnected sound
and dont know what device is connected as not shown in found new hardware and device manager
I also have been searching all possible keywords about what me and TS encountered but all linked to completely UNRELATED results(like search for long vibrations only link to people asking how to make vibration long and 1st result is this thread)
bountygiver said:
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
Click to expand...
Click to collapse
Silly question, but are you holding (and keep on holding) the Volume-Down button while you press the power button?
of course YES
i told you i have been flashing for so long
Leo from T-Mobile. Hi! I've got same problem. After flashing new (next) rom phone definetely died. Phohe is currently simfree and with HSPL. Only one reaction is short vibration after press power button. I searched everywhere. My phone has no bootloader but system see him as Qualcom CDMA Technologies MSM. Thats all, any ideas? Please and thanks for advice.
czaruch said:
Thats all, any ideas?
Click to expand...
Click to collapse
Yes, you flashed a non tmous stock rom that included a ..51.. radio and it destroyed your phone.
What rom? exact filename please.
thank you so much.
I bricked a Leo with the .51 radio. I think I read that is a European or otherwise foreign radio. Since your ROM has Euro in the name.......
czaruch said:
ROM_Leo_HTC_WWE_EastEurope_1-66.
Click to expand...
Click to collapse
The full filename for that rom is
RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Si gned_15.32.50.07U_2.07.51.22_2_Ship.exe
it comes with a version x.xx.51.x radio, and they do Not work on tmous (t mobile us) phones. They kill them
Your phone is dead, sorry. No known fix.
warranty or repair (or JTAG if you are brave and have the money)
a friend of mine bricked his phone. he then tried to microwave it, but that didn't work after that he took a power wire from an old computer, cut it and connected it directly to the phone's parts where the battery would go...this completely f-ed his phone up (he also used a lighter to fake a powersurge of the battery). Then he called htc and a few weeks later he got a new hd2!
GOOD LUCK
lol, he doesnt need to do any of that, its allready as dead as it can be. Loads of epople have had them replaced under warranty with this kind of brick. It wont start, so htc/tmo cant see that its been hacked.
Hi! I understand and realy sad. Somebody know where could I fix it in UK? And how much for this pleasure. Thanks.
i would contact htc, see what they have to say. (dont say you flashed it, it just stopped working")
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Veesais said:
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Click to expand...
Click to collapse
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
ParanoidKang said:
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
Click to expand...
Click to collapse
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Veesais said:
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Click to expand...
Click to collapse
Now the screen may not show, but try booting into fastboot mode by press and hold the Trackball+Power buttons together.
I'm not sure about the nexus one, but newer nexus devices have factory images, supplied by Google. If they exist for the nexus one, you should be able to save your device by flashing them through fastboot. That is if the images exist and you can get to fastboot.
Sent from my Nexus 4 using XDA Premium 4 mobile app
Hy, Guys.
first i want to say
Sorry for my English i am from Austria. so my first Language is German.
and also sorry for a second post,
but no one write me back so i thought i post my problem here again!!!!
My LG G4 H815 runs with Genesys 4.8 or 4.6.(dont know anymore) Bootloader Unlocked.
a few Days ago i had only 8% Battery so i put my Power cable in the device and go to sleep.
Next day i want to start my Phone an...........
NOTHING.
my G4 is Dead!!!!
i dont get it.
i try´d to start norm.
nothing.
put out the battery, put it back, try to start but
NOTHING...
Tryed to boot in Recovery but also NOTHING.
I tryed to power my Phone on without battery and Power Cable but no life sign.
no LED or Display Light goe´s on.
Now i put my G4 with usb on the Laptop but it did not reconize the Phone.
PLEASE GUYS PLEASE HELP ME.
I UNLOCKED MY BOOTLOADER!!!
And now i think my WARRANTY is gone.
I think the repair cost´s are verry high or do somebody know if LG Repair my PHone for free with unlocked BOOTLOADER???
sorry guys but i am done.
my nervs are gone..
If someone could help me that would be AMAZING and i could pay a few BEER´s-:fingers-crossed::good:
Thanks
Does the led blinks while charging(if this device has a led)
Regards milkyway3
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
Press and hold power button for 30 seconds, then release power button
Then connect your mobile with pc/laptop
Let it be charged for an hour
Then reboot it into fastboot and flash stock lollipop
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
mklkumar4 said:
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
Click to expand...
Click to collapse
Hey, thanks for your help.
I know how to enter into fastboot mode and all that stuff... but when I try to turn on my device, nothing happen, and if I connect my Moto E to the PC the device manager detects it as: qhsusb_bulk
It appears that the boatloder corrupted itself for some reason, a lot of people have the same issue.
I think it is hardbricked, but if you have some info that could help me, I'd be grateful
1st try to unlock bootloader if you are not able to do that, try to flash stock firmware this may help you
And please send screenshots of all the stuff that you can access in ur bricked device...! It will be helpful for me to understand