Related
O2 XDA model PM 300 dead during upgrade
I need help, my XDA is not running at all no sing of life , I try with holding camera and reset button nothing no sine ,
If anyone know how to start on or get into the tri-color screen , pls help
Regards
can u turn it on or is it completely dead??
if not, try another battery
I need help from all of you
I can’t start xda that is a problem, is dead , battery it was around 75 % , I need help if know of to start aging after my mistake during upgrade I install old upgrade and it stop on 3 colors screen in I move a usb cable after that I can not start any more if you have any info which it can help I will appreciatively
Regards to all
remove the batterry for a days time and check the next day have tried the same and with success
ipl 2.10
spl 3.08
radio 2.19
os 2.20 jesterz
You should find an extra usb cable and expose the black and red wires. Plug the oposite end into the usb port on your computer, then hold the red wire on the positive end of the battery and put the black wire on the negative end of the battery. Do this for about 30 seconds then put your battery back into your phone. This will restart your battery.
real help
I don’t have problem with battery , battery is working OK , I test in other xda , I have problem with XDA , is dead during upgrade , I put wrong upgrade and it stop on 3 colours and I move I usb cable and after I can not start power on or rest . If anyone know how please reply
Regards to all
haveriii said:
O2 XDA model PM 300 dead during upgrade
I need help, my XDA is not running at all no sing of life , I try with holding camera and reset button nothing no sine ,
If anyone know how to start on or get into the tri-color screen , pls help
Regards
Click to expand...
Click to collapse
Hi
Have u tried to force bootloader mode (the tri coloured screen),it is done, by pressing down the camera and while keeping it pressed,than press the power on button with other hand. It will switch on the device in bootloader mode( into the tri color screen) from there than flash the original Rom of ur carrier,which came pre-installed on the device or any other Official Rom from the same carrier.U can download official rom from ur carriers site.
Hope this will help and revive ur device.
secondly follow this excellent thread and read and ask for help there. Goodluck
http://forum.xda-developers.com/showthread.php?t=294107
help plz urgent
hi! friends need an urgent help plz while i was updating the rom my o2 got stuck with some blank screen written with "SERIAL" on the top and "VS1.02" at the bottom plz help how to get back my phone software
Can you enter bootloader? Hold the COMM manager button and soft reset.
@fardeen20
Please do not cross post the same thing in several threads. You have been answered alread. I have deleted the repeated posts for you. strike 1
Wow! There is a moderator for this forum!
Have you tried entering bootloader when the device is plugged into the charger? I know you say the battery works, but that doesn't mean the device can use the battery. Does the device do anything when plugged in or powered on?
dead prophet
im havin the same issue... my prophet wont even wake up... no power.. batt was more than 80% before flashed.. what can i do to get the power back..?? pls reply
Bootloader
Can someone post a picture of how the bootloader screen should look like?
I know it is a stupid question, but maybe that will help me solve my problem as well.
http://wiki.xda-developers.com/index.php?pagename=prophet_bootloader
may help.
i need the tool for upgrading htc pm300
I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???
brick is normal!
you should donate the brick to xda-developers now!
What you mean is normal ? is their anyway way i can get it fixed or is it just a paper weight now ?
probably runed out of battery. you should charge the battery in some way. try to power on the device while pressing camera button. it should show a boot loader screen. the you should flash a G4 SAFE ROM (with no spl/ipl) like "wizard love". if that doesnt help, sorry mate, you have a brick
are you able to enter bootloader?
hold down camera and either press power or reset button
No im not able to do anything on the phone lastnight it would go into bootloader randomly evey now and again but it isnt doing nothing now.
Ugh , i hope it is just the battery if it isnt then theirs nothing i can do for the phone unless i can get it in to bootloader mode right ?
your battery is dead...that's why you can't enter bootloader.
Moving to wizard G4.
Only the original charger is capable to charge your battery (it has a little bit more power), if it's fully charged... go into bootloader mode and install your official ROM the normal way.
It worked for me.
correct
im dealing with the same issue and my battery isnt dead
tasky smokey newbie bricks!! yomy !!
charly_mx said:
tasky smokey newbie bricks!! yomy !!
Click to expand...
Click to collapse
That's not very encouraging and nice thing to say.We all came here as newbies,not a big deal.
We all hate to see a guy loose his device like this,after all it's a developer's forum,we shud be atleast concerned and help out,if we can.
Hope you two be able to get your devices working again soon.
Good luck
Fixed
I just wanted to thank everyone for your help , i got my new battery in yesterday and my phone booted up flashed back to at&t orginal rom. Thank So Much.....
Hi there,
this is my 1st post so i hope to be a lucky one...
I installed minicm7 on my phone and everything was ok untill the 1st reboot.
Phone asked me for " Sim unlock network code " or something like that
so i restored my backup and started to use utilities
to unlock bootloader and other staff...
I was so " busy " that i didnt notice that my battery is out of battery
and my phone powered off in the middle of the process.
I cant turn it on now, i cant charge it, pc dont recognise it ( pc companion to ) and power button + menu, or back button etc dont work...
I charged my battery in a phone store, hoping that i could do something
but my phone is dead... it dosent response and i m afraid tha i damaged it.
Any idea / advice ?
ps. Sorry for my english, i hope that i made myself clear enough
ps2. I read similar threads but they didnt helped me at all
I havent managed to turn it on yet...
Any help plz ?
ps. If i send it at sony-ericcson store
will they charge me or warranty applies ?
If your phone doesn't even go into flash-mode there's not much you can do yourself
And I think they will notice you messed with it (rooted, unlocking bootloader), so they will charge you, I suppose
Isnt there anything at all tha i could do
before i send it for service ?
If you can't get it into flashmode, no, nothing at all
ok, thanx
i ll send it when i ll get paid...
unfortunatelly i ll have to wait for 1 more week
Good luck
If the reboot not work, just try it again and again.
if it still doesnt work, just try to flash it again.
I believe, normally the Android will not dead.
Do u try instal SEUS and restore orginal android
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Veesais said:
Hi there!
This thread is my last hope, so please dont let me down folks...:cyclops:
The story short - one sunny morning i turned on my HTC Nexus One and it got stuck with te X on the screen for about 15 minutes, non of the buttons responded, so i did the first thing that came in my mind - i pulled out the battery. After inserting the battery the phone went full brick, i mean literally, no reaction on anything, even conected to the wall charger, there is no sign of life, no charging LED, nothing. Connected to the PC, it says USB device not recognised.
I dont think this is a hardware proble, the phone workwd fine until this interrupted power on. Phone runned on stock Androud, i have not played aroun with it - no bootloader unlock, no rooting.
I searched the internet for a solution, tried a lot of button combinations like in this thread:
http://forum.xda-developers.com/showthread.php?t=1069032
but still no luck, i cannot restore or flash it while my PC does not recognise the phone.
Found some info about those Usb Jig things, but they work only on Samsung phones, so, is there a way to force the phone to go in recovery mode, or give any sign of life so i can try to recover it or flash a diferent ROM?
The warranty has ended, so no hope there.
Hope there is a way out of this, and, sory for my bad english. :good:
Click to expand...
Click to collapse
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
ParanoidKang said:
Well no, bricked is a term used when you are rooted and flash a bad rom,kernel,etc. You have no root, so you cannot be "bricked". Just a software failure, you cannot flash another rom because, again, you have no root or custom recovery. Your best bet is trying to send it back to your carrier and get it replaced
Click to expand...
Click to collapse
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Veesais said:
The warranty time is out, so there is no help from the carrier, unless for cash...
But there must be a way to bring it back to life.
Click to expand...
Click to collapse
Now the screen may not show, but try booting into fastboot mode by press and hold the Trackball+Power buttons together.
I'm not sure about the nexus one, but newer nexus devices have factory images, supplied by Google. If they exist for the nexus one, you should be able to save your device by flashing them through fastboot. That is if the images exist and you can get to fastboot.
Sent from my Nexus 4 using XDA Premium 4 mobile app
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
Press and hold power button for 30 seconds, then release power button
Then connect your mobile with pc/laptop
Let it be charged for an hour
Then reboot it into fastboot and flash stock lollipop
WAIFWAIF said:
Hello, everyone!
As you might guess I don't know if my device is hard bricked.
It began when I rooted my Moto E, installed a ROM and then the battery started to discharge way too fast than normal.
I tried to calibrate the battery but it didn't work, at some point the battery only lasted a couple of hours until one day my device turned off and it didn't turn on again.
When I plug the original charger or any other, only the white led blinks, I have already changed the battery for a new one, but the same thing is happenning, only white led blinks.
It is possible to "suddenly" hard brick a device? Because the only thing I did was to unlock the bootloader and install a ROM (Cardinal AOSP 1st and then cm-13.0-20161108-NIGHTLY-condor)
(Sorry for the mistakes, not native english)
Click to expand...
Click to collapse
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
mklkumar4 said:
don't worry i'm here to help you, once i was also a noob
firstly i need to know your knowledge level do you know how to reboot you phone into fastboot mode
have you installed any custom recovery to you device if yes it'll be so easy to resolve your problem
so give me those info :good:
Click to expand...
Click to collapse
Hey, thanks for your help.
I know how to enter into fastboot mode and all that stuff... but when I try to turn on my device, nothing happen, and if I connect my Moto E to the PC the device manager detects it as: qhsusb_bulk
It appears that the boatloder corrupted itself for some reason, a lot of people have the same issue.
I think it is hardbricked, but if you have some info that could help me, I'd be grateful
1st try to unlock bootloader if you are not able to do that, try to flash stock firmware this may help you
And please send screenshots of all the stuff that you can access in ur bricked device...! It will be helpful for me to understand