Hi.
I tried to flash mxq pro. I connected the mxq to the laptop through USB cable but nothing happened. Then I plugged in the mxq to the power supply while it being conmnected to the laptop.
Could that have damaged the usb port in the laptop since the mxq was on power?
Thanks
upgrade124 said:
Hi.
I tried to flash mxq pro. I connected the mxq to the laptop through USB cable but nothing happened. Then I plugged in the mxq to the power supply while it being conmnected to the laptop.
Could that have damaged the usb port in the laptop since the mxq was on power?
Thanks
Click to expand...
Click to collapse
No this shouldnt cause any damage, some devices need both usb and ppwer connected to complete the flashing process, are you holding the reset button while connecting? You may need to use mask rom mode to force it to be detected if reset button isnt working Look on my YouTube Channel for "AMLOGIC Unbrick using mask rom mode" this video shows the process https://youtube.com/c/AidanMacgregor
Related
Hello
I buy this box from gearbest and comes faulty, is DEAD!
When I Plug power, only blue led lights on, nothing more.
I try to put firmware on sdcard, press reset button (inside AV Plug), connect power cable. But doenst work.
I also try use USB BURNING TOOL, But software never detects anything.
Some people talk to connect 2 pins in V NAND Flash, for s805. But in my Board I dont knbow if is possible or not, and how I can do it.
Hey, have same problem, but after unsuccessful flash. After disassembly, i found rs232 pins, but i'm no guru to know how. Any help would be appreciated. T95m 2/8gb
Jan
Hello everyone, I have a T95z Plus Amlogic S912 2g ram octa core 16 gb rom, it used to work fine, but one day suddenly it stopped booting, so i tried to reflash it with the burning tool, but then i realized that when i plug it to a computer, it works, it boots and everything is fine, it even works if i disconnect it from the power source, leaving it jus powered by the computer throught the usb cable, anyway, i did flashed the rom with the burning tol, and the problem continues, the box doesnt work while connected throught the power brick, but it works fine just connected to the pc with the usb port
sniffviper said:
Hello everyone, I have a T95z Plus Amlogic S912 2g ram octa core 16 gb rom, it used to work fine, but one day suddenly it stopped booting, so i tried to reflash it with the burning tool, but then i realized that when i plug it to a computer, it works, it boots and everything is fine, it even works if i disconnect it from the power source, leaving it jus powered by the computer throught the usb cable, anyway, i did flashed the rom with the burning tol, and the problem continues, the box doesnt work while connected throught the power brick, but it works fine just connected to the pc with the usb port
Click to expand...
Click to collapse
had same trouble my power cord was bad put new power cord working fine
Hello guys
I'm really desperate creating this topic, but about a problem i have with the flashtoom for my x96 Mini S905w
So far, i've tried
Using different versions of the USB burning tool program (2.06, 2.09,2.16)
Using differente firmwares (atvx 2FF, 2C, 2F, official x96 mini firmware 12052018, amlogic upgrade firmware)
Using Windows 10 and windows 7
Ticking and unticking erase flash (with normal erase, force, erase all) in every combination
Plugging USB while pressing the reset button with and without power plug
All of them give the same error : 0x10303004 (as attached in the image) at 4% percent uboot
Whats worse, the box seems to be softbrick (black screen on tv, nothing showing, even tried flashing with usb card maker with no luck, no recovery showing at all) at some point, still blue light, still recognized by computer but no sign of image or recovery on tv, even with sd card or usb recovery to flash (yes, i pressed the reset button too)
Am i missing something or something that i havent try yet? is it brick for good? I even open the box and attach the image, i think im using the correct firmwares. Please let me know if theres any solution to this. Im attaching the error log too.
Try T95S1 Image
Still having problems?
I think you will have to use the short pin method.
I can send you the photo of the board and which pins you have to short.
I'm not home right now.
Enviado do meu POCOPHONE F1 através do Tapatalk
can someone help me...how to enter recovery in X96 mini i want to flash it but i can not... there is a pin in AV hole which i keep pressing but no recovery mode, also PC does not see device etc...heeeeeeeeelp
You are flashing ROMs for s905w, instead of s905x.
Check below links for compatible ROM
http://firmware.duckdns.org/
https://forum.freaktab.com/forum/tv...s905x/others-aml-s905x/firmware-roms-tools-bx
https://mega.nz/#F!GEpQmQhZ!ezNEXQdnyNIhm2axjnfTIg
If your LED is red and not turning blue, try to power on using USB male A cable and power adaptor.
elazu1 said:
Hello guys
I'm really desperate creating this topic, but about a problem i have with the flashtoom for my x96 Mini S905w
So far, i've tried
Using different versions of the USB burning tool program (2.06, 2.09,2.16)
Using differente firmwares (atvx 2FF, 2C, 2F, official x96 mini firmware 12052018, amlogic upgrade firmware)
Using Windows 10 and windows 7
Ticking and unticking erase flash (with normal erase, force, erase all) in every combination
Plugging USB while pressing the reset button with and without power plug
All of them give the same error : 0x10303004 (as attached in the image) at 4% percent uboot
Whats worse, the box seems to be softbrick (black screen on tv, nothing showing, even tried flashing with usb card maker with no luck, no recovery showing at all) at some point, still blue light, still recognized by computer but no sign of image or recovery on tv, even with sd card or usb recovery to flash (yes, i pressed the reset button too)
Am i missing something or something that i havent try yet? is it brick for good? I even open the box and attach the image, i think im using the correct firmwares. Please let me know if theres any solution to this. Im attaching the error log too.
Click to expand...
Click to collapse
I installed a firmware I didn't like on my Scishion V88 PRO. I opened USB BURNING TOOL, connected my TV BOX (which does not have a reset button, not even inserting a toothpick into the AV input) to reinstall the previous firmware. But by connecting the USB cable to the PC, USB BURNING TOOL no longer detects the BOX! What may have happened? There is a solution?
NB: Before restarting the restoration, I had reset the device, and when I turn it on, only the AMLOGIC form appears and remains locked on it.
Thank you for those who will try to help me
I tried to flash the ATV Xperience rom using the steps shown in the Youtube tutorial, but I could never get the USB Burning Tool to even recognize my box. It's not the tool per se, but that my computer never sees a USB connection when connecting the A95X MAX OTG port to my PC. So here's a list of stuff I've tried:
1) Connect the OTG port of the A95X MAX (the USB 2.0 port next to the HDMI) and connected that into the Amlogic's Burning Tool, device does not show up in the list, no power plug.
2) Connect the OTG port of the A95X MAX, with power plug. Device still does not show up.
3) Connected HDMI from TV to the A95X MAX, held down reset button inside the A/V 3.5mm port, plugged in the DC plug, kept holding it down, never saw recovery.
4) Box used to boot after a long wait, but it doesn't even boot anymore.
mayb this video can help..
https://m.youtube.com/watch?v=2ZfLxgJtmps
or just ask at freaktab forum....
https://forum.freaktab.com/forum/tv...al-wifi-gig-lan-bt4-2-support-2-5inch-ssd-hdd
missing the driver for your android box.
reinstall usb burning tool, it should ask to install a "worldcup" driver as well.
some Android boxes dont like USB 3 (Cable or ports)
Thanks for the suggestions, none of them worked, I pulled the damn thing apart and reflowed the usb connectors and its ESD diodes.
Chinese designed anything is just absolute garbage, learned my lesson with Teclast and Amax, won't be repeating this again, gonna give my money to Samsung from here on out, their software isn't great, but they can make some damn fine hardware...
Watch this installation guide video, if you want to install ATV Xperience without PC/LAPTOP.