Related
Received a brand new Ace yesterday, and immediately rooted it with super one click with no problems.
However I then tried to run the 'Galaxy Ace Unlock apk' which I'd found elsewhere.
It generated an unlock pin, but after rebooting it stuck on the Galaxy Ace flash screen. After 5 minutes I pulled the battery out, waited, then rebooted. Now it doesn't even get to the Galaxy Ace screen when switched on.
The screen backlight comes on (with a black screen) for a couple of seconds, then off, then on - but it never gets any further.
So far I've tried
- Flashing Stock Froyo via Odin
- Flashing VillainRom via Odin
In both cases the phone enters download mode, Odin completes all steps without error, but on reboot I am left with the black screen of death again!
Anything else I could try?
I have the same problem.
Have you found a solution?
zongamin said:
Received a brand new Ace yesterday, and immediately rooted it with super one click with no problems.
However I then tried to run the 'Galaxy Ace Unlock apk' which I'd found elsewhere.
It generated an unlock pin, but after rebooting it stuck on the Galaxy Ace flash screen. After 5 minutes I pulled the battery out, waited, then rebooted. Now it doesn't even get to the Galaxy Ace screen when switched on.
The screen backlight comes on (with a black screen) for a couple of seconds, then off, then on - but it never gets any further.
So far I've tried
- Flashing Stock Froyo via Odin
- Flashing VillainRom via Odin
In both cases the phone enters download mode, Odin completes all steps without error, but on reboot I am left with the black screen of death again!
Anything else I could try?
Click to expand...
Click to collapse
Hey!
Dose you RESET FACTORY SETTINGS and FORMAT CACHE in recovery, before flashing with ODIN?
CHEERS!
Did the light lit when you entered the download mode? That's the indicator.
I got the same proble, tried several firmwares with odin but, when the phone reboots it starts flashing again
Hey!
You all, try THIS one.
CHEERS!
casiocas said:
Hey!
You all, try THIS one.
CHEERS!
Click to expand...
Click to collapse
I tried it, several times with different firmwares but it doesn´t do anything. The phone, when rebooting with odin, keeps flashing the black screen
moe_szislack said:
I tried it, several times with different firmwares but it doesn´t do anything. The phone, when rebooting with odin, keeps flashing the black screen
Click to expand...
Click to collapse
Hey!
Just wanted to ask, FROM WHERE you downloaded you UNLOCK soft. Can you give me the link? PLEASE!
CHEERS!
casiocas said:
Hey!
Just wanted to ask, FROM WHERE you downloaded you UNLOCK soft. Can you give me the link? PLEASE!
CHEERS!
Click to expand...
Click to collapse
Sorry if it sound rude, it wasn´t my intention.
I download the soft form samfirmwares.com.
Cheers
moe_szislack said:
Sorry if it sound rude, it wasn´t my intention.
I download the soft form samfirmwares.com.
Cheers
Click to expand...
Click to collapse
Ok, I get. But SORRY, then I cant help. You must contact then, from where you downloaded it.
Just I hope you get fixed your phone(If you most take it to SERVICE, try to explain them that you tryed RESET FACTORY SETTINGS. It work for several ppl-s here, who must take his phone to SERVICE). Just be 10 times SURE, that you cant flash or recovery you phone, or they can do the same and see that your phone WAS ROOTED or FLASHED the CUSTOM ROM(JUST BE SURE, THEY CANT ACCESS YOU PHONE or you lose you WARRANTY).
I hope all ENDS good! Fingers crossed for you phone!!!
CHEERS!
casiocas said:
Ok, I get. But SORRY, then I cant help. You must contact then, from where you downloaded it.
Just I hope you get fixed your phone(If you most take it to SERVICE, try to explain them that you tryed RESET FACTORY SETTINGS. It work for several ppl-s here, who must take his phone to SERVICE). Just be 10 times SURE, that you cant flash or recovery you phone, or they can do the same and see that your phone WAS ROOTED or FLASHED the CUSTOM ROM(JUST BE SURE, THEY CANT ACCESS YOU PHONE or you lose you WARRANTY).
I hope all ENDS good! Fingers crossed for you phone!!!
CHEERS!
Click to expand...
Click to collapse
I forgot to say that I put a sim card (from other country) inside the ACE to check if it was unlocked.
Can it be the problem?
moe_szislack said:
I forgot to say that I put a sim card (from other country) inside the ACE to check if it was unlocked.
Can it be the problem?
Click to expand...
Click to collapse
Hey!
I want to help you, REALLY, but a bout that queation, I CANT ANSWER, RIGHT NOW. DONT KNOW EXACTLY. SORRY!
I try to find answers tomorrow(we have here 23:27). Tomorrow to work.
CHEERS!
casiocas said:
Hey!
I want to help you, REALLY, but a bout that queation, I CANT ANSWER, RIGHT NOW. DONT KNOW EXACTLY. SORRY!
I try to find answers tomorrow(we have here 23:27). Tomorrow to work.
CHEERS!
Click to expand...
Click to collapse
Ok, Thank you
Need help screen just flashes and blinks..
Tried multiple rom flashes...odin says pass but the ph doesn't boot up
Sent from my SAMSUNG-SGH-I897 using XDA App
misterio_mr111 said:
Need help screen just flashes and blinks..
Tried multiple rom flashes...odin says pass but the ph doesn't boot up
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
The same thing happens to me, Anybody has any idea?
Just send it to the service center.
No other recovery method is know.
I have been in every forum arond for this kinda brick and there is no solution for YOU to do. Also there is absolutely no way for Samsung to see either say that after the first boot the battery went dead and it never started again. It will be covered by your warranty and brand new ace! Now dont go making stupid mistakes again hope i helped
Sent from my GT-S5830 using XDA App
Apk/sim bricked my phone.
Unlock Apk also bricked my phone in the same manner.
The app generating the code is not the problem on it's own, it's when you put the "other" Sim card in and reboot that does the damage.
I got a buzz when i could still get Download Mode and Odin gave me a PASS when i reflashed, but alas the phone never rebooted and it still flashed black at me.
I'm trying everything to bring it back to life before it goes to the Service Centre and i have to give them some blag as to why it's bricked.
Other than Download Mode i can get "Emergency Dload Mode"(ARM9) & RAMDUMP.
BLZBud said:
Unlock Apk also bricked my phone in the same manner.
The app generating the code is not the problem on it's own, it's when you put the "other" Sim card in and reboot that does the damage.
I got a buzz when i could still get Download Mode and Odin gave me a PASS when i reflashed, but alas the phone never rebooted and it still flashed black at me.
I'm trying everything to bring it back to life before it goes to the Service Centre and i have to give them some blag as to why it's bricked.
Other than Download Mode i can get "Emergency Dload Mode"(ARM9) & RAMDUMP.
Click to expand...
Click to collapse
I got the same problem and still nobody has found how to unbrick the phone.
I´ll keep searching
moe_szislack said:
I got the same problem and still nobody has found how to unbrick the phone.
I´ll keep searching
Click to expand...
Click to collapse
Even Samsung don't have an easy way to repair it, hence they replace the mainboard to fix the issue.
Hi all,
I have looked for a similar post, I found out that many people experienced something like that trying unlocking their phones, but I haven't found out any solution.
Here is my situation:
I have tried to unlock my s5830 (orange spain carrier), I have used a method which it seems to be dangerous for the phone, but of course I have found out it was dangerous after I have already tried it
Anyway after I discovered the unlock number contained in the perso.txt file in the efs folder, my phone restarted without service once and after that it went in a bootloop mode, it goes on a download mode, but there is no way to get back recovery mode or a normal boot.
I flashed the s5830 several times with many firmware, but no one worked, and the phone is still stuck in an infinite loop, in which I am not even able to see the samsung logo coming out at the very beginning.
I know many phones got bricked in this way, I wanted to know if anybody has been able to recover the phone or if anybody know any possible solution.
And if not, do you know if the warranty is covering this problem? I just got the phone a couple months ago; i have unlocked other devices before, but this is the first time I have experienced a problem so I am quite new about warranty as well. Please HELP ME
Merry Christmas guys!!!
Thanks in advance
sfrat said:
Hi all,
I have looked for a similar post, I found out that many people experienced something like that trying unlocking their phones, but I haven't found out any solution.
Here is my situation:
I have tried to unlock my s5830 (orange spain carrier), I have used a method which it seems to be dangerous for the phone, but of course I have found out it was dangerous after I have already tried it
Anyway after I discovered the unlock number contained in the perso.txt file in the efs folder, my phone restarted without service once and after that it went in a bootloop mode, it goes on a download mode, but there is no way to get back recovery mode or a normal boot.
I flashed the s5830 several times with many firmware, but no one worked, and the phone is still stuck in an infinite loop, in which I am not even able to see the samsung logo coming out at the very beginning.
I know many phones got bricked in this way, I wanted to know if anybody has been able to recover the phone or if anybody know any possible solution.
And if not, do you know if the warranty is covering this problem? I just got the phone a couple months ago; i have unlocked other devices before, but this is the first time I have experienced a problem so I am quite new about warranty as well. Please HELP ME
Merry Christmas guys!!!
Thanks in advance
Click to expand...
Click to collapse
if you can get into download mode im guessing there is some hope for you.
go here: http://droidangel.blogspot.com/2011/05/samsung-galaxy-ace-s5830-original-stock.html
look for: S5830XXKP9
and make sure you have odin 4.38 and flash with that.
try to install cwm and install a customrom
Sent from my GT-S5830 using xda premium
sfrat said:
Hi all,
I have looked for a similar post, I found out that many people experienced something like that trying unlocking their phones, but I haven't found out any solution.
Here is my situation:
I have tried to unlock my s5830 (orange spain carrier), I have used a method which it seems to be dangerous for the phone, but of course I have found out it was dangerous after I have already tried it
Anyway after I discovered the unlock number contained in the perso.txt file in the efs folder, my phone restarted without service once and after that it went in a bootloop mode, it goes on a download mode, but there is no way to get back recovery mode or a normal boot.
I flashed the s5830 several times with many firmware, but no one worked, and the phone is still stuck in an infinite loop, in which I am not even able to see the samsung logo coming out at the very beginning.
I know many phones got bricked in this way, I wanted to know if anybody has been able to recover the phone or if anybody know any possible solution.
And if not, do you know if the warranty is covering this problem? I just got the phone a couple months ago; i have unlocked other devices before, but this is the first time I have experienced a problem so I am quite new about warranty as well. Please HELP ME
Merry Christmas guys!!!
Thanks in advance
Click to expand...
Click to collapse
with the cellphone off, put out ur baterry for a minute, then maintain ur finger into the volume down button and the power button tell a friend or if u can alone insert the batery while quickly pressing volume down and power button to get into download mode, and flash.
Hehehe,bootloop is horrible,you just have to get in download mode & flash with 2.3.4 firmware with Odin,just that steps and you save your SGA.
I got bootloop many times and Odin saved me.
Sent from my SGA
robinandroid said:
try to install cwm and install a customrom
Sent from my GT-S5830 using xda premium
Click to expand...
Click to collapse
he cant go back in recovery mod............
If you can go to recovery mode than you can just wipe the data and cache. This saved me many times. Otherwise on what ever OS you may be , just create new user name after removing samsung android drivers. Login from new user name and than re install drivers again and now flash your phone from firmware which was installed on your phone before you bricked it. This helped me a few times.
dr_vishal said:
If you can go to recovery mode than you can just wipe the data and cache. This saved me many times. Otherwise on what ever OS you may be , just create new user name after removing samsung android drivers. Login from new user name and than re install drivers again and now flash your phone from firmware which was installed on your phone before you bricked it. This helped me a few times.
Click to expand...
Click to collapse
hey guys thanks for the answers, but unfortunately i am not able to reach the recovery mode, my phone just reach the download mode.....i will try with the xxkp9, even if i have already tried it...I guess i have tried at least 15 firmwares without any success
Helping to make your Christmas Merry
It seems that you've already received a lot of help for unbricking your device. So I'll try to help out in unlocking your phone after you finished unbricking it.
This is the method I personally used on my locked Ace:
http://forum.xda-developers.com/showthread.php?t=1335548
It's perfectly safe. 100%.
King Kaze said:
if you can get into download mode im guessing there is some hope for you.
look for: S5830XXKP9
and make sure you have odin 4.38 and flash with that.
Click to expand...
Click to collapse
I have tried the XXKP9 again, it is not working, as usual Odin ends to load the firmware and then it goes back in the endless loop mode....there is no chance to get it back?
franzks said:
It seems that you've already received a lot of help for unbricking your device. So I'll try to help out in unlocking your phone after you finished unbricking it.
This is the method I personally used on my locked Ace:
http://forum.xda-developers.com/showthread.php?t=1335548
It's perfectly safe. 100%.
Click to expand...
Click to collapse
thank you very much I will follow your advice...IF I will be able to get my phone back which seems impossible =(
@dr_vishal
Thank you first of all, I have tried to uninstall and reinstall the android device driver, but it doesn't seems to be the problem, Odin ends with a "PASS" at the end, I guess there still is comunication in the between the two devices...
Hopefully it will be a Merry Christmas =)
It's not impossible. I'm relatively new here but I have noticed quite a few "bricked" threads already. Most of them (if not all) have been able to fix their device. I haven't seen a single person permanently brick their device, so I would guess that your chances of fixing it are really high. Just be patient and keep describing your situation and more experienced help will certainly arrive. I'd really like to help out but I have no idea how to fix it as I have not experienced bricking my phone yet.
Anyway, if the method for unlocking I suggested works for you kindly press the Thanks Button. Merry Christmas!
franzks said:
It's not impossible. I'm relatively new here but I have noticed quite a few "bricked" threads already. Most of them (if not all) have been able to fix their device. I haven't seen a single person permanently brick their device, so I would guess that your chances of fixing it are really high. Just be patient and keep describing your situation and more experienced help will certainly arrive. I'd really like to help out but I have no idea how to fix it as I have not experienced bricking my phone yet.
Anyway, if the method for unlocking I suggested works for you kindly press the Thanks Button. Merry Christmas!
Click to expand...
Click to collapse
Thank you franzks!
I promise I will try your method and I am positive it will works, but I need to get my phone back...so I will add few new information I have found out talking to a friend of mine which has my same device and the same carrier as well.
The version built-in is:
GINGERBREAD.BVKQ9
S5830BVKQB
[email protected]#1
Any suggestion about the firmware I am suppose to flash in?
I am actually passing through all the version contained in the address droidangel you gave me...at the moment no one is working...I will keep trying...
sfrat said:
Thank you franzks!
I promise I will try your method and I am positive it will works, but I need to get my phone back...so I will add few new information I have found out talking to a friend of mine which has my same device and the same carrier as well.
The version built-in is:
GINGERBREAD.BVKQ9
S5830BVKQB
[email protected]#1
Any suggestion about the firmware I am suppose to flash in?
I am actually passing through all the version contained in the address droidangel you gave me...at the moment no one is working...I will keep trying...
Click to expand...
Click to collapse
Guys,
I am out of ideas, I have tried each single firmware I have seen around internet, no one is working, any tip or advice or suggestion?
I messed up with the efs, and I guess that's all, the phone is gone....now it needs a JTAG or whatever is its name....
maybe to get the warranty still valid I should broke totally the phone over charging it....??
sfrat said:
Guys,
I am out of ideas, I have tried each single firmware I have seen around internet, no one is working, any tip or advice or suggestion?
I messed up with the efs, and I guess that's all, the phone is gone....now it needs a JTAG or whatever is its name....
maybe to get the warranty still valid I should broke totally the phone over charging it....??
Click to expand...
Click to collapse
Did you try that?
http://forum.xda-developers.com/showthread.php?t=1153310
just a thought
a lot of people have talked about reflashing it and all but have you managed to get into the recovery mode at all once you have reinstalled the rom with odin? if you can get to that you just need to hit factory reset, wipe cache and wipe dalvik and normaly after that it will work fine... so far ive been stuck in soft brink 3 times and each time doing the wipes from the recovery mode has worked...
Pinting said:
Did you try that?
http://forum.xda-developers.com/showthread.php?t=1153310
Click to expand...
Click to collapse
I've tried to use the oneclick, but it seems it doesn't recognize the phone, since, i guess, it's made for a galaxy s.
The others are not my case, since I am able to get download mode, and all these are made to can get it back.
Anyway I found out a post in which the people were talking about the s5500, which apparentely is similiar to my device, and the owners of that model experienced a similar problem doing the same process....anyway in that post the people needed to use a Jtag, which is the only way to get it back....so I though it could be the same solution for my problem...but I don't know anybody with Jtag, so the only way is contacting the service center.
thanks anyway, when I will be back at home after Christmas I will try to find the ticket and I will probably try to get it back in warranty, since is preatty new...
@torchwolfery
I am not able to reach recovery mode, there is no way to get it back, even flashing the phone with different firmwares, all I got is download mode, and apparently that is completely pointless...since the only change in the phone behavior is that if i install a certain firmwares it doesn't even have the back-light working when it is stuck in bootloop.
Warranty is your only hope (as it was mine once and it worked).
I didn't think it was possible to brick these phones. There I have tried so much to try and brick it but I have not been able to as it still always goes into 'download' mode. The only advice I can give you is double check that you are using the correct version of Odin which is v4.38 and that you use cooper v1.0 as your OPS. If dont mind me asking, but exactly what did you do or do you remember the steps you took to brick it? What buttons are you using for 'recovery' mode.
Also please clarify if Odin is going in a loop or does the phone come on and then keeps rebooting? If it is the phone that keeps rebooting, then wiping cache and data partition should do the trick. This can be done by going into recovery mode (which I am aware you cannot get into) or if you can manage to get into the dialler quick enough before the reboot, by dialling *7267*3855# and that should format the relevant partitions (data and cahce) and bring it back to factory settings. Without further info, I cannot really tell exactly what the situation is.
The fact that you are getting 'download' mode, I dont think that it is bricked because it will still allow you to write the relevant directory/files to the relevant blocks. Either way, would be interested to know.
Hi my process of root and installation gone very bad. now my mobile does not power up by itself but only when its connected with PC via USB cable it flashes intermittently, please see the attached photo.
How it happens:
1. SG II was okay and functional so i entered into recovery mode and did wipe clean of data and then cache.
2. Entered into download mode and tried Odin and install custom Rom but there were few rejected attempt.
3. Odin was terminated and mobile battery removed to try again
4. It shown me "software update failed logo" plz see image i uploaded.
5. my phone still connectable with Odin, so i flashed it with "MyGKernelV1.1.1_CWM5.tar" as we found it in one forum to fix this error message.
6. Took battery out and this boot-loop stuck on my mobile. (See the first image uploaded, its kind of screen saver as this logo keep going on n off)
Odin 3 does not register it connected on my PC, i cannot enter into recovery or download mode.
Please, let me know if anyone got idea to fix it, will appreciate lot, as after 3-4 hours search through numerous forums and pages, i am frustrated.
Pictures uploaded to show my case are searched online to be close enough but they represent same problem.
Regards
Sunny
model:GT-I9100G
Baseband: I9100GZCLPK
Kernel:3.0.8-1067026
Build No: IMM76D.ZQLR7
That's forced download, get a stock ROM meant for your device and flash it via odin.
Now that I think about it the only thing I saw was the pic you posted so I dunno if your pc sees your device.
if it does, cool.
If it doesn't try another cable/port/pc/re install kies and on and on. Check the last page of the phistachio thread about unbricking, there's a lot of guys with that exact problem.
PS: I didn't want to edit it either so I kept typing. Crazy.
Sent from the little guy
Thanks mate, yep Odin doesnt not show it connect to PC so i got hard ball to play...i was fixing my mate's mobile and got kinda bad feeling that his mob bricked , he will be devastated if i cannot make it work...
...thanks again ...your words sounds nice to me and i will give it a go..
gastonw said:
That's forced download, get a stock ROM meant for your device and flash it via odin.
Now that I think about it the only thing I saw was the pic you posted so I dunno if your pc sees your device.
if it does, cool.
If it doesn't try another cable/port/pc/re install kies and on and on. Check the last page of the phistachio thread about unbricking, there's a lot of guys with that exact problem.
PS: I didn't want to edit it either so I kept typing. Crazy.
Sent from the little guy
Click to expand...
Click to collapse
sunnym_1999 said:
Thanks mate, yep Odin doesnt not show it connect to PC so i got hard ball to play...i was fixing my mate's mobile and got kinda bad feeling that his mob bricked , he will be devastated if i cannot make it work...
...thanks again ...your words sounds nice to me and i will give it a go..
Click to expand...
Click to collapse
Since it's showing you that forced download screen (it's the device's way to beg you to flash something because as it for now, nothing is working for it) I can tell you that is not THAT bricked just yet. You just need your pc to see it.
Try other Odin versions and make sure you get the right ROM for your device.
BTW, are you sure it's a I9100G device? did you check under the battery?
Before i started wiping and cleaning it, i made note of its model no, baseband etc ...so all that info is right.
Also, to give you better idea, this mobile current state is this one attached again..it keep flashing this screen info when connected with laptop otherwise it stays blank.
gastonw said:
Since it's showing you that forced download screen (it's the device's way to beg you to flash something because as it for now, nothing is working for it) I can tell you that is not THAT bricked just yet. You just need your pc to see it.
Try other Odin versions and make sure you get the right ROM for your device.
BTW, are you sure it's a I9100G device? did you check under the battery?
Click to expand...
Click to collapse
And it shows I9100G.
What happened with the other screen? Does it show up at all?
Sent from the little guy
No that screen was there for a while till i did Step 4 and dis appeared when i applied that patch on step five ....please see my very first post on top..
gastonw said:
And it shows I9100G.
What happened with the other screen? Does it show up at all?
Sent from the little guy
Click to expand...
Click to collapse
Oh, sorry, now I remember. It was when you flashed something from other site.
So, no DL mode? 100% sure? usb jig is your next step then.
Sent from the little guy
gastonw said:
Oh, sorry, now I remember. It was when you flashed something from other site.
So, no DL mode? 100% sure? usb jig is your next step then.
Sent from the little guy
Click to expand...
Click to collapse
That's what i figured out,
looking on
http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-download-mode-jig/
:good: thanks mate...
Okay so my phone randomly rebooted 2 days ago and when it got to the LG logo screen it froze. I tried to hard reset it, i went in to the hard reset menu clicked yes once then confirmed the hard reset by selecting yes a second time and the phone froze on highlighted yes. I have pulled the battery and tried to do this multiple times to no avail. So next i went to my PC and started google searches. Often i found things such as being stuck in boot loop which my phone wasn't, it was just frozen at the LG logo screen. Regardless I like to think of myself as self educated tech savvy (which now from reading all of your posts im not, im not even a little bit, in fact im tech stupid.) I did follow post through to the LGUP tool and downloaded a stock KDZ and got my phone into download mode>firmware update screen, i was able to get al the correct drivers and get LGUP to recognize the device and i loaded the stock KDZ and tried to do a Complete wipe reinstall. The program as able to interact with my device and went through the process, i thought i had fixed my phone. After a fresh install(or what i thought was a fresh install) i rebooted after the update and went to the LG logo screen and froze. The only difference is now when my phone starts, right before the LG logo appears i get the green android robot with what looks like open working "guts" real quick before it goes to the Logo and freezes. So back to the drawing board and i wanted to attempt some of the things ive seen like TWRP recovery etc but here i am getting lost. Forgive me if im posting things that have been answered but i keep getting confused. I dont know what the difference is between fastboot boot loader recovery mode or any of that is. also i kept noticing time and time again that my phone has to be in USB debugging mode and i dont know if it is. I cant turn my phone on to get it into USB debugging mode now anyways. Im okay with my warranty being voided and im okay with rooting if thats what i have to do to make it work. I have installed ADB and fastboot and some twrp recoveries etc but im clueless. Lastly know that i never Rooted my phone or anything but i was a torrent downloader. forgive me im triyng to provide as much information as possible.
PLEASE NOTE - I had to sign up to post here obviously and i loved how it said if you have an IOS go buy an android and come back LOL
Message Tung Kick. He can get u out of anything
Hit thnx if this helpd
tried
joshualuna said:
Message Tung Kick. He can get u out of anything
Hit thnx if this helpd
Click to expand...
Click to collapse
i tried to message tung kick and it said user not found?
sjeffreysmith said:
i tried to message tung kick and it said user not found?
Click to expand...
Click to collapse
Use Messenger on FB
i appreciate the resonse
joshualuna said:
Use Messenger on FB
Click to expand...
Click to collapse
is that the name to search for on fb? "tung kick"
sjeffreysmith said:
is that the name to search for on fb? "tung kick"
Click to expand...
Click to collapse
Try again on here but lower case and name is one whole wrd. tungkick
joshualuna said:
Try again on here but lower case and name is one whole wrd. tungkick
Click to expand...
Click to collapse
not having luck with him yet but ill keep trying. is there any other posts or something you could point me towards?
sjeffreysmith said:
not having luck with him yet but ill keep trying. is there any other posts or something you could point me towards?
Click to expand...
Click to collapse
http://forum.xda-developers.com/tmobile-lg-v10/development/debrick-phone-h901-qualcomm-9008-t3440359
This thread by him may help.
jsu718 said:
http://forum.xda-developers.com/tmobile-lg-v10/development/debrick-phone-h901-qualcomm-9008-t3440359
This thread by him may help.
Click to expand...
Click to collapse
SD card my only option?
I got a P9000 in the late spring, and have been really happy with it. Unfortunately I dropped it on the ground, and the screen cracked, after which the touch function did not work (but the phone did) I finally managed to get a new screen from China, and it has been installed by a local shop dealing with mobiles. However, the shop told me they could/would not deal with anything else but changing the LCD screen. The phone switches on (I can hear starting jingles and emails downloading etc) but the screen just turns from black to dark blue and stays that way. I have been trawling through the forums, but not sure what to do next. Take it that I need to flash it, and have followed the instructions given here, but it just seems to time out. Anyone got the patience to walk me through this?
UKrugger said:
I got a P9000 in the late spring, and have been really happy with it. Unfortunately I dropped it on the ground, and the screen cracked, after which the touch function did not work (but the phone did) I finally managed to get a new screen from China, and it has been installed by a local shop dealing with mobiles. However, the shop told me they could/would not deal with anything else but changing the LCD screen. The phone switches on (I can hear starting jingles and emails downloading etc) but the screen just turns from black to dark blue and stays that way. I have been trawling through the forums, but not sure what to do next. Take it that I need to flash it, and have followed the instructions given here, but it just seems to time out. Anyone got the patience to walk me through this?
Click to expand...
Click to collapse
I am facing same thing here. The screen is not coming up at all, But I can hear sound too. ANyone else who has changed the screen successfully before?
yes, i changed the screen successfully. After screen replacement i flashed the newest rom with flashtools and all was ok.
DonMagnifico said:
yes, i changed the screen successfully. After screen replacement i flashed the newest rom with flashtools and all was ok.
Click to expand...
Click to collapse
Can you describe the precise process you followed. I seem to get stuck when I try to flash the phone
UKrugger said:
Can you describe the precise process you followed. I seem to get stuck when I try to flash the phone
Click to expand...
Click to collapse
skeleton1911 describe in this thread how to flash the P9000:
http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
in this thread from skeleton1911 you find all links to the needed files:
http://forum.xda-developers.com/showpost.php?p=66784596&postcount=146
change screen start logo screen after light on/off all the time 2sec
DonMagnifico said:
skeleton1911 describe in this thread how to flash the P9000:
http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
in this thread from skeleton1911 you find all links to the needed files:
http://forum.xda-developers.com/showpost.php?p=66784596&postcount=146
Click to expand...
Click to collapse
hello, thank you for you help. i've change the screen p9000 and when i put battery the screen logo elephone turns on and turns off two second always.is it normal and is it essential new flash when you put a new screen. in periph manager i see two second USB Vcom MT 65xx preloader but it's disapear 2seconde all the time because logo elephone light on and off two second. If you give me a solution, you are the best.
the pc don't recognize telephone of course. but i'm tm trying your methode but i've meet difficult with install pilot.
thank you XDA
thank you to help me, all the day i'm trying solutions,after the screen change, Flashtool tell sucess download, but it continues to turn on and off with the logo elephone starts. in peripheral it appears and disappears every two seconds. i don't know if there is a room in my phone. how to inject the files in the phone with a Peripheric always on and off. help me please. after flashtool ok download the screenis black and nothing i move battery and after logo elephone on/off but nothing else. someone know the reason on/off and appear an desappear in device : Mt65xx USBVCOM.
tanguy66 said:
hello, thank you for you help. i've change the screen p9000 and when i put battery the screen logo elephone turns on and turns off two second always.is it normal and is it essential new flash when you put a new screen. in periph manager i see two second USB Vcom MT 65xx preloader but it's disapear 2seconde all the time because logo elephone light on and off two second. If you give me a solution, you are the best.
the pc don't recognize telephone of course. but i'm tm trying your methode but i've meet difficult with install pilot.
thank you XDA
Click to expand...
Click to collapse
You are in a boot loop. This is not a bad sign, now you know the screen works. It's normal that you have to flash the Rom again after replacing the screen. if you use flashtool, start download in flashtools before you connect your phone to the PC, then hold vol+ on your P9000 and connect the phone to the pc.
DonMagnifico said:
You are in a boot loop. This is not a bad sign, now you know the screen works. It's normal that you have to flash the Rom again after replacing the screen. if you use flashtool, start download in flashtools before you connect your phone to the PC, then hold vol+ on your P9000 and connect the phone to the pc.
Click to expand...
Click to collapse
always the same problem: light on off all 2 seconds, with B+vol+ i see recovery 1 seconde. i haven't the time to do something. question is it possible the battery bad, the logo flash all the time if the battery bad the logo don't go isn't it. please help i'm trying plenty solution but no good . thank you.
tanguy66 said:
always the same problem: light on off all 2 seconds, with B+vol+ i see recovery 1 seconde. i haven't the time to do something. question is it possible the battery bad, the logo flash all the time if the battery bad the logo don't go isn't it. please help i'm trying plenty solution but no good . thank you.
Click to expand...
Click to collapse
no, it's not the battery. You made a mistake by flashing the rom, now you are in a boot loop. Ignore the message on the screen. Try to flash the rom again. start flashtool, select the scattertext, click download, hold vol+ button on the phone and connect the phone to the PC
PLEASE HELP me, can you give me a solution to start up the phone again
hello , before flash tool all is ok flashing GOOD, now it's more bad now i have no lignt no logo, and when use flash tool always stop download 20% BROM error: status dowwnload exeption (0xc0050003) (HINT) : , i don't know if i have a good battery
yesterday i have a new image appears it'a big beautiful battery only one bar after logo several times. i'm found an d try all solutions, 4 days , i sleep at 1 oclock. help to find a solution. how to know or test if the telephone is dead or little life.
OK now i arrived with flash tool i begin all zero, and message OK Good, i'm verry worried, no light , no logo??have you a solution to know if the battery now? thank you help.
do you know when the message tell OK,it means all things an room is now ok in the phone. I'm not sure
just now i'm testing battery with tester 3v 1ma it's good. how to do to light screen now. it's strange.
and with electric power it must work normaly ,or not if the battery dead?
i think you flashef the wrong preloader. flash the phone again with the newest firmware. in #5 you find a link to the needed files.
DonMagnifico said:
skeleton1911 describe in this thread how to flash the P9000:
http://forum.xda-developers.com/elephone-p9000/how-to/how-to-guideline-install-mtk-drivers-t3344042
in this thread from skeleton1911 you find all links to the needed files:
http://forum.xda-developers.com/showpost.php?p=66784596&postcount=146
Click to expand...
Click to collapse
After a couple of tries, I did manage to get this working. Initial failure seemed to be me not pressing the "Vol +" button. Thanks very much for your help
DonMagnifico said:
i think you flashef the wrong preloader. flash the phone again with the newest firmware. in #5 you find a link to the needed files.
Click to expand...
Click to collapse
thank you. i use flash tool v5.1620. i have windows 7 32 bit,mtk 65 vcom is update, i'm not sure what do you mean. newest firmware. i have last room for p9000. can you tell more details please or more link to succeed. i read, and i trying a lot, now i swimming again.
UKrugger said:
After a couple of tries, I did manage to get this working. Initial failure seemed to be me not pressing the "Vol +" button. Thanks very much for your help
Click to expand...
Click to collapse
ok , i don't understand with flash tool i have plenty of time a big download is ok, if the download is ok why it's doesn't working.
the phone is often remains dark. I put in charge the battery with two 2mn special machine at my work , and it's wake up the phone souddenly appears again the elephone logo and battery with 1 once bar, I don't know if it's me or the battery or something else. normally if I plug in USB i must have lignt Electric power? but nothing.
thank you and not let me down please i need you.
tanguy66 said:
ok , i don't understand with flash tool i have plenty of time a big download is ok, if the download is ok why it's doesn't working.
the phone is often remains dark. I put in charge the battery with two 2mn special machine at my work , and it's wake up the phone souddenly appears again the elephone logo and battery with 1 once bar, I don't know if it's me or the battery or something else. normally if I plug in USB i must have lignt Electric power? but nothing.
thank you and not let me down please i need you.
Click to expand...
Click to collapse
Sorry, I can' t help you more. All I know i telled you. But write a private message to skeleton1911, he has a great experience in reactivating Phones. May be he can help you.
P9000 screen replacement
Hi . I had my p9000 about 2 months when I sat on it and cracked the screen,the casing was very slightly curved so I gave it to a shop to repair,now nearly 2 months later they say they can't get it to start up. They tried a new battery and I told them what I'd read on this forum regarding flahing the rom but They gave me back the phone with a new screen and nothing else, so I told them i'm not paying for 1/2 a repair and told them to remove the new screen and give me back the phone as it was . What do you think could be the problem if a repair shop cannot repair a screen and install new sorftware is there hope for it?
Hi, i broked my screen again so i am not a newbie about this... but this time after flashing the Phone show nothing at all... the small LED Dot is shining when android is boot, so i dont think the cable is connected wrong. The touch works fine..What can it be??