I dropped my phone in water for maximum 5-6 seconds. I pulled the battery out, dried it with a towel then ...(later i realize it was stupid) tried to turn it back on. It just did a fast boot loop without even pressing the power button. It's like the power button was stuck?
Then i read the online guides about the rice. So i put the phone in a rice container for 12 hours. I took it out and turned it on (using the power button). This time, it actually turned on, loaded up the KISS screen (I'm using ICS KISS) then it would just reboot to Vibrant again.
I also tried vol + and got download mode but when i did vol - i did not get recovery
Turned it off, put it back into the rice. Hoping things might change. Got a backup phone for the time being.
Question is... Can I simply flash the phone to stock or is a component linked to the main SDCard corrupted?
Thanks for the help!
Hello there! Are you comfortable with talking the phone apart? If so (only if you are), i myself would take out the battery asap with no power connect to the device. Then i would simply take it apart and leave it in parts to let dry. I would also look around for possible corrosion around soldered connections. If corrosion (usually white powdery looking kinda like a battery terminal in a car), i would take rubbing alcohol and a tooth brush and scrub it away. Then let it sit and let dry. Once dried out reassemble and insure that the connection ribbons are very securely in place. Sometimes when a phone is dropped and starts to boot loop, it just means a connector isn't all the way connected anymore. But considering that water is in the picture, it could be a combination. By the way this is at your own risk and this is what i would personally do and have done with success. Ive seen phones with plenty of water still in them after the rice thing. I hope this helps you out man. Good luck and if you do choose to take apart your phone just take your time and be careful. I would only take out the main board and the board that connects to it and not worry about anything else that isn't a board. Sorry for the book lol.
Sent from my SAMSUNG-SGH-I717 using XDA
If you Google "how to install front faced camera vibrant mobiletech video", watch the youtube video because they take apart the back of the phone. It not as hard as you think. Then put it in a bag if rice like the above post said. Good luck!
Sent from my SGH-T959 using xda premium
Ok, Here's what happened
I was cleaning the toilet at home and foolishly placed my phone on the tank, as I finished I picked up my phone, slipped out of my hand and fell in the toilet. I know I know, why did I take my phone to the toilet? I have no idea, its the first and last time have done that.
Anyway, I removed the battery, sim and sdcard straight away and tried to dry the phone off as much as possible, then placed the phone and battery separately in a concealed bag filled with dry rice (to absorb moisture), I can now boot my phone.
The problem is that the phone says I need to charge my battery, now when I try and connect the charger, it says, 'Charging has stopped due to overheating'.
My question to all you pros, is this a battery or phone issue? I don't really want to order a new battery to find it's a problem with my phone. If it helps, when I tried charging it, I noticed excessive heat down one side of the phone, as shown in the attached image.
Be gentle :crying:
...
You didn't mention how LONG you kept the phone components in bags of rice before trying to reassemble and power the phone.
If it was anything less than several days (if using rice as a desiccant, most recommendations I have seen are a week, minimum) and this is the only technique you attempted to use to dry the phone out, then it is very likely the phone was not completely dry when you powered it back up, and you may have permanently damaged key electronic components by allowing an electrical charge to flow through them before they were completely dry.
MistahBungle's call of the board responsible for the USB port is a good guess on which component, though.
Thanks for your replies guys.
I only kept it in the bag for 48 hrs. As you mentioned this probably wasn't long enough. I may just try and claim through our house insurance as it does cover smart phones, I don't have normal phone insurance because I've never needed it until now.
Thanks again for your help.
This was my question before I converted it into a tutorial:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
This tutorial was made possible by @xange and @georgeiulian89. Thanks!
Usually when you drop your phone, you would be doomed. Or so you thought. With this tutorial, you can save A LOT of money buying a new phone or repairing the wet phone!
HOWEVER, I CANNOT GUARANTEE THAT YOUR PHONE CAN REVIVE. THIS WORKED FOR ME (SHALLOW DIP IN WATER). YOU MIGHT ALSO NEED A NEW BATTERY (IF YOU THINK YOU CAN REVIVE IT)
Steps(suggested by xange, proved):
1. Remove your phone from the water source IMMEDIATELY! (duh) DO NOT ATTEMPT TO SWITCH IT ON OR PRESS ANY BUTTON.
2.Remove the battery, SIM and micro SD cards.
3.Dry the body with a dry cloth. Try not to use tissue paper as it will leave residue.
4.Disassemble the phone, all the way to the motherboard. I used a small slotted screwdriver (the one with only one edge)as there are screws shaped like stars. If you have that type of screwdriver you can use it. Similar disassembly video here: www.youtube.com/watch?v=ginuDIeNCs8
WARNING: INTERNAL PARTS ARE VERY SENSITIVE TO STATIC, METAL,ETC. BE CAREFUL. ALSO REMOVE THE CONNECTIONS TO THE FRONT COVER AND DIGITIZER (display) BEFORE REMOVING THEM.
5.Direct a blowing fan to all the internal parts to dry them. Keep the screws and parts in an accessible area. Leave it for 30 minutes. DO NOT DRY IT WITH A HAIRDRYER. YOU ARE JUST TRYING TO SCREW YOUR PHONE.
6.Reassemble the phone and insert the battery ONLY. NOTE: Make sure the ribbon connector is clean before connected, if dust (or any tiny electric conductor) sticks on the connector while connecting them, you will have high chancesof damaging the phone. Then, switch on the phone. If not,
A) CHARGE IT: Your phone battery might be 100% dead(until normal charging can't power it on). For me I pressed and held the Back button while plugging the charger into the phone (Flashmode). The LED should blink red and eventually, green. This is when normal charging starts.
B) REPLACE THE BATTERY: You'll need to do so especially when the (once)white area near the connectors of the battery has turned red, indicating battery damage.
C) SEND IT TO A (optional: AUTHORIZED) SERVICE CENTER: Out of luck. This is the furthest I can help.
ALTERNATIVE DRYING METHODS:
A)PUT IT IN RICE FOR A DAY: NO, Asians won't come to repair your phone. Rice acts like silica, which absorbs moisture like sponge. I suggest you disassemble the phone first as rice might get into the small holes around your phone.
B)SOAK IN ALCOHOL, THEN PUT IT OUT: Disassemble it first, too. Though I haven't tried this method, there are those who have proved it to work.
C) RADIATOR DRYING (suggested by georgeiulian89): I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on.
C)DRY IT WITH A HAIRDRYER: NO. RISKY METHOD. Water will evaporate, then condense back somewhere once you've done hairdrying your phone it will condense back. I tried it and it condensed on my phone's camera lens. (It's a hairdryer, not a phonedryer!)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hope this tutorial helps those out there whose phones have went swimming (or diving)
THANK ME IF I HELPED
Jessss
Sent from my Xperia Neo V using XDA Premium 4 mobile app
karanrajkapur said:
Jessss
Sent from my Xperia Neo V using XDA Premium 4 mobile app
Click to expand...
Click to collapse
If you mean yes, then HOW?
fenzo3 said:
If you mean yes, then HOW?
Click to expand...
Click to collapse
What i believe is you've broken your battery and i didn't get anything what you asking about the display. It doesn't light up or what???
Sent from my Xperia Neo V using XDA Premium 4 mobile app
I dropped my Xperia Neo into water for 3 times, yet still operable, i mean, it survived 3 times of dropped into a pail of water, NO JOKES! .
What you should do is, the moment you dropped your phone into water, pick it out of water immediately, open the back cover and take out the battery immediately to prevent further electric short circuit. You will need some small tool to open every single screw to get the mother board come out (careful when unplug those ribbon sockets, if it breaks, you may have to pay to replace it) and dry (using hair dryer?) every single spot in the phone, except the screen, the screen should be tightly seal and should have no water enter into it. maybe the rubber physical buttons you have to take out and dry it too. (DON'T open the screen no matter what happen, unless water really enters the screen, or else the dust enter and stick at the screen you will have a REALLY HARD TIME { i mean it } to clean those dust out of the screen) confirm everything is dried and then assemble it. (from here onwards, it is a luck test whether you still able to save your phone or not, a line between hell and heaven) Put in your battery, It is normal you may not able to turn on your phone at first, give it a charge about 20 minutes and leave it there (red LED may blink repeat-ly for a while and you will not able to turn it on, just leave it) then switch it on, If you still can't turn it on, try change the battery. If symptom persist, god bless you, i tried my best helping you. ( it means it may not 100% probability to save your phone, but it is a way i did to save my phone)
Eventhough my phone survived dropping into water for 3 times, but it has some problems now, a random one, the phones get really really hot for no reasons for a short period (about 1 hour to 2 days) the heat comes from the motherboard after my inspection, maybe some water droplet enter into the chips and causing electric short circuit?
Good luck.
xange said:
I dropped my Xperia Neo into water for 3 times, yet still operable, i mean, it survived 3 times of dropped into a pail of water, NO JOKES! .
What you should do is, the moment you dropped your phone into water, pick it out of water immediately, open the back cover and take out the battery immediately to prevent further electric short circuit. You will need some small tool to open every single screw to get the mother board come out (careful when unplug those ribbon sockets, if it breaks, you may have to pay to replace it) and dry (using hair dryer?) every single spot in the phone, except the screen, the screen should be tightly seal and should have no water enter into it. maybe the rubber physical buttons you have to take out and dry it too. (DON'T open the screen no matter what happen, unless water really enters the screen, or else the dust enter and stick at the screen you will have a REALLY HARD TIME { i mean it } to clean those dust out of the screen) confirm everything is dried and then assemble it. (from here onwards, it is a luck test whether you still able to save your phone or not, a line between hell and heaven) Put in your battery, It is normal you may not able to turn on your phone at first, give it a charge about 20 minutes and leave it there (red LED may blink repeat-ly for a while and you will not able to turn it on, just leave it) then switch it on, If you still can't turn it on, try change the battery. If symptom persist, god bless you, i tried my best helping you. ( it means it may not 100% probability to save your phone, but it is a way i did to save my phone)
Eventhough my phone survived dropping into water for 3 times, but it has some problems now, a random one, the phones get really really hot for no reasons for a short period (about 1 hour to 2 days) the heat comes from the motherboard after my inspection, maybe some water droplet enter into the chips and causing electric short circuit?
Good luck.
Click to expand...
Click to collapse
I followed a disassembly video for the Neo, but unfortunately the Neo V has a slightly different assembly, so I could not remove the screen to get access to the motherboard. Also, before I put it in rice, I tried to turn it on (Sony said it was water-resistant) after 12 hours in rice. The screen went all weird but I could hint the LegacyXperia kernel logo. That was before my phone booted up normally, and died upon charging.
For your heat problem, perhaps rust? Water should have evaporated from the heat and condensed everywhere in the motherboard.
Would soaking it in alcohol help?
fenzo3 said:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
Click to expand...
Click to collapse
I guess that it's a problem with the battery, not with the display (probably the battery has been short-circuited). I dropped my phone (Xperia Neo) in water 3 days ago. I've took it out after about 10-15 seconds (this was the time until i've realised that it dropped). The phone was still working fine, it didn't shut down by itself. What i did: I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on. Gues what: it works without any problem, just like before the incident. You should check the water damage indicator on the battery (it's a white strip near the connectors of the battery). If it's white, the phone don't have any problem, but if it's pink or red, the phone was damaged by the water. Mine it's white, with some very little pink on the edge (before it was completely white).
georgeiulian89 said:
I guess that it's a problem with the battery, not with the display (probably the battery has been short-circuited). I dropped my phone (Xperia Neo) in water 3 days ago. I've took it out after about 10-15 seconds (this was the time until i've realised that it dropped). The phone was still working fine, it didn't shut down by itself. What i did: I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on. Gues what: it works without any problem, just like before the incident. You should check the water damage indicator on the battery (it's a white strip near the connectors of the battery). If it's white, the phone don't have any problem, but if it's pink or red, the phone was damaged by the water. Mine it's white, with some very little pink on the edge (before it was completely white).
Click to expand...
Click to collapse
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
fenzo3 said:
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
Click to expand...
Click to collapse
To get rid of 100% battery issue, you might just want to flash stock ftf in the first place, give it a full charge and then flash your desired driver.
Sent from my Xperia Neo V using XDA Premium 4 mobile app
fenzo3 said:
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
Click to expand...
Click to collapse
try battery calibrator by zeppelinrox. i couldn't recall where he put the script. try search around XDA.... good luck.
---------- Post added at 09:26 PM ---------- Previous post was at 09:16 PM ----------
fenzo3 said:
This was my question before I converted it into a tutorial:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
This tutorial was made possible by @xange and @georgeiulian89. Thanks!
Usually when you drop your phone, you would be doomed. Or so you thought. With this tutorial, you can save A LOT of money buying a new phone or repairing the wet phone!
HOWEVER, I CANNOT GUARANTEE THAT YOUR PHONE CAN REVIVE. THIS WORKED FOR ME (SHALLOW DIP IN WATER). YOU MIGHT ALSO NEED A NEW BATTERY (IF YOU THINK YOU CAN REVIVE IT)
Steps(suggested by xange, proved):
1. Remove your phone from the water source IMMEDIATELY! (duh) DO NOT ATTEMPT TO SWITCH IT ON OR PRESS ANY BUTTON.
2.Remove the battery, SIM and micro SD cards.
3.Dry the body with a dry cloth. Try not to use tissue paper as it will leave residue.
4.Disassemble the phone, all the way to the motherboard. I used a small slotted screwdriver (the one with only one edge)as there are screws shaped like stars. If you have that type of screwdriver you can use it. Similar disassembly video here: www.youtube.com/watch?v=ginuDIeNCs8
WARNING: INTERNAL PARTS ARE VERY SENSITIVE TO STATIC, METAL,ETC. BE CAREFUL. ALSO REMOVE THE CONNECTIONS TO THE FRONT COVER AND DIGITIZER (display) BEFORE REMOVING THEM.
5.Direct a blowing fan to all the internal parts to dry them. Keep the screws and parts in an accessible area. Leave it for 30 minutes. DO NOT DRY IT WITH A HAIRDRYER. YOU ARE JUST TRYING TO SCREW YOUR PHONE.
6.Reassemble the phone and insert the battery ONLY. Then, switch on the phone. If not,
A) CHARGE IT: Your phone battery might be 100% dead(until normal charging can't power it on). For me I pressed and held the Back button while plugging the charger into the phone (Flashmode). The LED should blink red and eventually, green. This is when normal charging starts.
B) REPLACE THE BATTERY: You'll need to do so especially when the (once)white area near the connectors of the battery has turned red, indicating battery damage.
C) SEND IT TO A (optional: AUTHORIZED) SERVICE CENTER: Out of luck. This is the furthest I can help.
ALTERNATIVE DRYING METHODS:
A)PUT IT IN RICE FOR A DAY: NO, Asians won't come to repair your phone. Rice acts like silica, which absorbs moisture like sponge. I suggest you disassemble the phone first as rice might get into the small holes around your phone.
B)SOAK IN ALCOHOL, THEN PUT IT OUT: Disassemble it first, too. Though I haven't tried this method, there are those who have proved it to work.
C) RADIATOR DRYING (suggested by georgeiulian89): I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on.
C)DRY IT WITH A HAIRDRYER: NO. RISKY METHOD. Water will evaporate, then condense back somewhere once you've done hairdrying your phone it will condense back. I tried it and it condensed on my phone's camera lens. (It's a hairdryer, not a phonedryer!)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hope this tutorial helps those out there whose phones have went swimming (or diving)
THANK ME IF I HELPED
Click to expand...
Click to collapse
add in: make sure the ribbon connector is clean before connected, if dust(or any tiny electric conductor) stick at connector while connecting them, you will have high chances to spoilt the phone.
Water got into my phone(obviously) and I tried turning it on because of water resistance. It didn't respond. So I tried charging it. Tell my why the phone's battery screen flashed? NVM that, I tried the ol' bag full of rice trick. I left it there for about 12 hours. I tried again, and I got into recovery, but with a reddish tint. Well, I tried re-installing my ROM, hoping that it was an easily fixable issue. When the rom was installing, I unplugged my phone, instant power off. And my phone was at 100% before the install. I panicked, and knowing that I had to use my phone soon, I did probably the stupidest move ever, and put it on AN ELECTRIC HEATER. I left it there for 5 minutes, because that heater gets so hot that the air in my whole house is dry after ~30 minutes. Now sometimes when I turn it on, if the charger isn't in, the apps initialize, then power off, other times I get nothing. If I put the charger in, I sometimes get a white-ish triangle with a red thermometer(I'm guessing temperature warning?) and sometimes the battery flashes periodically. Please help, because of family health problems I need to be able to use my phone.
EDIT***: Phone WILL turn on now, condensation on both cameras, and battery temp too low to charge, so now there's a broken thermometer.
GG3K said:
Water got into my phone(obviously) and I tried turning it on because of water resistance. It didn't respond. So I tried charging it. Tell my why the phone's battery screen flashed? NVM that, I tried the ol' bag full of rice trick. I left it there for about 12 hours. I tried again, and I got into recovery, but with a reddish tint. Well, I tried re-installing my ROM, hoping that it was an easily fixable issue. When the rom was installing, I unplugged my phone, instant power off. And my phone was at 100% before the install. I panicked, and knowing that I had to use my phone soon, I did probably the stupidest move ever, and put it on AN ELECTRIC HEATER. I left it there for 5 minutes, because that heater gets so hot that the air in my whole house is dry after ~30 minutes. Now sometimes when I turn it on, if the charger isn't in, the apps initialize, then power off, other times I get nothing. If I put the charger in, I sometimes get a white-ish triangle with a red thermometer(I'm guessing temperature warning?) and sometimes the battery flashes periodically. Please help, because of family health problems I need to be able to use my phone.
EDIT***: Phone WILL turn on now, condensation on both cameras, and battery temp too low to charge, so now there's a broken thermometer.
Click to expand...
Click to collapse
This phone is not water resitant. So trying to turn it on, before it dried completely was not that great of an idea. You could still have someone disassemble it, clean the board in alcohol and replace the battery. I think you just overheated the battery and you might have several shorts on your "mainboard". So please stop using it, until someone cleaned the board at least in some isopropanole or even better isoprop in an ultrasonic device. Dont just throw it in completely, but the "mainboard" only.
Sent from my SM-G925F using XDA Free mobile app