I figured out my previous TWRP issue, but I'm scratching my head trying to install a new ROM. I take a clean micro sdcard, format it, and look for the ~ 3GB image file I put on it, but it's not there. If I (through TWRP) go up, I see a bunch of folders, and nothing one folder down. I'm missing something stupid....what s it?
TIA!
Steve
crackface said:
... look for the ~ 3GB image file I put on it, but it's not there....
Click to expand...
Click to collapse
What are you looking with?
Screenshots might help us to understand.
Which system is installed btw?
My apologies for not providing enough info, I figured it out. I was using the wrong button combination. Thank you for the response though!! It was working mostly towards the end but I wasn't hitting the right buttons to bring up the TWRP buttons. I asked a mod to remote it, but guess they didn't see it in time.
I did post another issue I still can't seem to figure out when installing google apps. Any input would be greatly appreciated!!
I feel like a jerk, I didn't even post the keypresses that got me where I needed to be, and now I forgot what they were. I'll figure out what those were and repost them here. Sorry!
*EDIT*
OK, found them. From a cold boot (power off) I held Vol up and Home button (no power). It then goes to TWRP splash page, and if you hold long enough you'll get the 8 buttons (Install, Wipe, etc). A few people elsewhere described a different button push set which threw me off a little bit.
crackface said:
I feel like a jerk, I didn't even post the keypresses that got me where I needed to be, and now I forgot what they were. I'll figure out what those were and repost them here. Sorry!
*EDIT*
OK, found them. From a cold boot (power off) I held Vol up and Home button (no power). It then goes to TWRP splash page, and if you hold long enough you'll get the 8 buttons (Install, Wipe, etc). A few people elsewhere described a different button push set which threw me off a little bit.
Click to expand...
Click to collapse
That button combo is peculiar.
My T825 (what's yours?) reacts to home+pwr+vol-up which starts TWRP.
Does yours really start from pwr-off state that way?
Related
Hey guys I need your help asap!!!
I already rooted my HTC Thunderbolt but I'm still fairly new to all of this. I was going through my phone and I seen that I had a firmware update available so I decided to start it up. I thought it would be a quick and easy update so started the update and left the room. I came back 2 hours later and my thunderbolt had a black screen with a exclamation mark inside of a triangle to the left of a little android guy. I couldn't leave that screen unless I pressed the power button and volume keys at the same time. Once rebooted everything looks normal, and everything begins to load up but only 10 secs later my phone begins to power down again and I have no control of it. Once powered down, a loading droid comes up as if something is starting to download, but once the loading bar reaches the middle of the status bar, the image I mentioned earlier comes up again.
If it helps the last two things I have changed on my thunderbolt was I flashed Lean Kernel extreme and installed Launcher Pro....Any help is appreciated, I just hope I didn't do what I think I did (bricked it)
Hardknocks82 said:
Hey guys I need your help asap!!!
I already rooted my HTC Thunderbolt but I'm still fairly new to all of this. I was going through my phone and I seen that I had a firmware update available so I decided to start it up. I thought it would be a quick and easy update so started the update and left the room. I came back 2 hours later and my thunderbolt had a black screen with a exclamation mark inside of a triangle to the left of a little android guy. I couldn't leave that screen unless I pressed the power button and volume keys at the same time. Once rebooted everything looks normal, and everything begins to load up but only 10 secs later my phone begins to power down again and I have no control of it. Once powered down, a loading droid comes up as if something is starting to download, but once the loading bar reaches the middle of the status bar, the image I mentioned earlier comes up again.
If it helps the last two things I have changed on my thunderbolt was I flashed Lean Kernel extreme and installed Launcher Pro....Any help is appreciated, I just hope I didn't do what I think I did (bricked it)
Click to expand...
Click to collapse
Tried a factory reset?
It doesn't give me time to get to my Rom manager
You are rooted so u shouldnt have done that update...
hold the power button and the volume down button at the same time...see if you can boot into recovery....
damn...so what do you suggest???
read my post # 5
yeah when I do that I just reboot back to the phone again then 10secs after Im rebooted, it says "powering down" and gives me the same exclamation mark inside the triangle and the little android guy next to it
Hardknocks82 said:
yeah when I do that I just reboot back to the phone again then 10secs after Im rebooted, it says "powering down" and gives me the same exclamation mark inside the triangle and the little android guy next to it
Click to expand...
Click to collapse
when you hold down the power button and volume down and it reboots....doesn't it go to a white screen? I beleive it says recovery in blue......if you use the volume down to highlight it...then press the power button.....it should reboot into recovery.......
alright I just turned it off and I pressed the power button and the volume down....the white screen came up and its now asking me if I want to start update. If I press the "no" option I should be good right? I just want to make sure before I do anything else
Hardknocks82 said:
alright I just turned it off and I pressed the power button and the volume down....the white screen came up and its now asking me if I want to start update. If I press the "no" option I should be good right? I just want to make sure before I do anything else
Click to expand...
Click to collapse
what you have to do....is let the phone reboot normally.....then when the phone bbot up...connect to your computer.....delete the radio file on your SD card...it will say something like PG51....zip...then hold the power button and volume down.....then it will not ask you for an update when it reboots...then you can go and highlight recovery...
Do you think it will be just as effective if I took my sd card out and just deleted that file you mentioned?? because seeing that my phone turns off after only a few secs of it being rebooted I dont have enough time to syc it to my computer
Hardknocks82 said:
Do you think it will be just as effective if I took my sd card out and just deleted that file you mentioned?? because seeing that my phone turns off after only a few secs of it being rebooted I dont have enough time to syc it to my computer
Click to expand...
Click to collapse
that will work!!! take out the card...delete the radio file....should be PG51xx.zip...put it back...hold power button and volume down button...phone reboots into white screen...use volume button to highlight recovery...then push power button....phone will reboot into recovery.....
also..save the file that you are deleting off the sd card...you will need to reinstall after you restore the rom you want...
okay so I guess I ended up doing it the hard way but its cool I guess...
basically I held the volume down button and then pressed and held the power button until hboot comes on like you said but it didn't allow me to select anything other than "yes" or "no" to continue the update or not. It will check the file, then ask if I wanted to update. I pressed volume up for yes. After update, I pressed power to reboot.
After pressing the down key to stop the update, and I seen that it didn't work after 5 or 6 tries (because it just rebooted and did nothing), I just pressed the volume up.
Once it rebooted after I pressed the volume up key it restored my phone like the first day I got it. its a little annoying because now I have to download everything again but at least its not bricked
Thanks a lot man, I completely appreciate your time and effort...
glad you
Hardknocks82 said:
okay so I guess I ended up doing it the hard way but its cool I guess...
basically I held the volume down button and then pressed and held the power button until hboot comes on like you said but it didn't allow me to select anything other than "yes" or "no" to continue the update or not. It will check the file, then ask if I wanted to update. I pressed volume up for yes. After update, I pressed power to reboot.
After pressing the down key to stop the update, and I seen that it didn't work after 5 or 6 tries (because it just rebooted and did nothing), I just pressed the volume up.
Once it rebooted after I pressed the volume up key it restored my phone like the first day I got it. its a little annoying because now I have to download everything again but at least its not bricked
Thanks a lot man, I completely appreciate your time and effort...
Click to expand...
Click to collapse
glad you got it...but all you had to do is delete the PG51..zip file off your SD card and you would have been able to reboot into recovery...if you have the P51...zip file on your phone.....it will ALWAYS ask you to update....
For the record, when that black screen with the exclamation mark comes up, you are in recovery. All you had to do was press menu. I just made this same mistake like a noob, now I gotta wait until my lunch break to fix it.
This is a pretty common mistake
Hello guys. At first i´m so sorry for my bad english, so i´ll show you a video of my problem.
Phone - HTC Hero, Android 2,1
Video:
I can´t post outside links in my messages...
youtube. com/watch?v=V1BwQZsoKCk
It will not go to sleep mode when pressing the end/power key. But it still takes phone OUT of sleep mode, but now I have to wait for the screen timeout instead of pressing the button again.
I tried to find answer to my question, but i failed... I tried Reboot, Spare Parts - i don´t know if it worked properly, Hard reset, but the power button still not working properly.
Thank you! Marty
Restore you phone to the default setting and softares
Sent from my awesome X8 using Tapatalk
I tried that... No results
Marty Chill said:
I tried that... No results
Click to expand...
Click to collapse
Try to restore your phone to the default, or try to install a custom rom
Sent from my awesome X8 using Tapatalk
Now i did a ROOT and i try to flash in some ROMs but it still not works + it cancels my outcoming and incoming calls...
Sounds like you have a failing power button.. like I do.
It's a real pain in the ass... been looking for solutions for quite a while, besides physically replacing the circuit board the button is on...
I know this is old but for anybody researching the same problem... after trying MANY different apps for taking over power button tasks, the only real solution was to buy a replacement "Flex Cable" assembly on eBay. Takes some bravery to install but everything works now.
But that's just my experience.
I suppose that the simplest way out id button remapper that you can find hear at xda.
By using such software you can easily turn any of the other physical keys of your device into the power button.
lucaoldb said:
I suppose that the simplest way out id button remapper that you can find hear at xda.
By using such software you can easily turn any of the other physical keys of your device into the power button.
Click to expand...
Click to collapse
True, and they did work once the phone was up and running. However, when something went wrong on my rom and I needed to get into recovery to re-flash... I was SOL.
Yes, remapping is applied only after the kernel is loaded... So remapping is quite useless if the phone is switched off.
Hi All,
I have flashed EUViewPad 7 based on Stock rom. installed SD Card Booster, CPU Master and etc.
The flash is fine since I managed to boot it and install several apps.
Until I needed to reboot the device since the hacker keyboard always forces to close. I rebooted it and poof I am in infinite boot animation without a way to remove the battery. afraid to fiddle just waited the battery to drain so I can test again(This happened on my O1. just removed the battery, put it back and its ok)
I have drained the battery after almost 8 hours of non stop boot animation. But this device won't turn on anymore. It just vibrates when I press the on button.
Tried opening the back(crap I have scratched the back covering. now it has large scratches ) but the battery is taped . My question folks is what is the possible solution to my problem aside from removing the battery(can't even get to clockword recovery)
Thanks
Not too sure about your device, but doesn't yours have a reset button like the viewpad?
Should be a small hole on the bottom edge right next to the microphone.
Try pressing that with a paperclip if you're having boot problems.
Anyway, if you've drained the battery completely, make sure to leave it charging for a little while. Too low battery voltage will make it unable to start. 15 mins or so should be more then enough.
Try starting with both volume buttons + power pressed. Keep holding it until you see "entering recovery mode."
Let me know if this gives any results.
Amalgation said:
Not too sure about your device, but doesn't yours have a reset button like the viewpad?
Should be a small hole on the bottom edge right next to the microphone.
Try pressing that with a paperclip if you're having boot problems.
Anyway, if you've drained the battery completely, make sure to leave it charging for a little while. Too low battery voltage will make it unable to start. 15 mins or so should be more then enough.
Try starting with both volume buttons + power pressed. Keep holding it until you see "entering recovery mode."
Let me know if this gives any results.
Click to expand...
Click to collapse
Ahh I have that reset button beside the microphone hole. Will try this later on. Thanks for your help and for your custom rom
Uh oh... Tried pressing the small hall beside microphone, pressed on button. No luck. tried pressing that hole and on at the same time No luck again.
Is it possible that it will mess up the whole boot process due to boot animation loop??
silencer07 said:
Uh oh... Is it possible that it will mess up the whole boot process due to boot animation loop??
Click to expand...
Click to collapse
I'm afraid and it sounded like, from your descriptions, that the boot process has been messed up .... so, what do you got to lose by trying to "wake" it up or at least respond to commands, right ?
Try holding the power button & use a small pin to press RESET - leave it connected to the power supply/charging unit.
Try holding both volume Up & Down key & use a small pin to press RESET
Try holding both volume Up & Down key along with the Power button at the same time, and press RESET (you might want to get someone to help you to this)
Try holding the volume Down (left) key & Power button, and press RESET with a small pin.
Does any of these work in getting the screen to show life, be patient as you might have to hold it for 10 to 30 seconds before it cycle & restart/display the 3 birds ...
Chances are you will need to flash a stock ROM with the SULT3 utility, and then if successful, root it again & start over (carefully) - it might work or it might not even connect via usb at all .... worth a try, got nothing to lose at this point.
As a last resort, contact Cherry Mobile and get it repaired & sending it back to the shop .... check the warranty details in your locale, opening the rear case & exposing the battery, might or might not void your warranty coverage.
Hi Letiride,
I have tried the combinations you have specified but no avail. I can't boot this so my PC with correct drivers cannot even recognize i plugged this.
Is my Tablet already bricked?? I have bought this second hand so no warranty already.
Huhuhu Did I already have one of the "Vibrator" Android phone
silencer07 said:
tried the combinations but no avail. I can't boot this so my PC with correct drivers cannot even recognize i plugged this.
Is my Tablet already bricked?? .... bought this second hand so no warranty. (
Click to expand...
Click to collapse
Oh mine, no - if it won't power up or boot into Recovery or FTM mode, I'm afraid it's critical if not officially certified "paperweight". Try uninstalling your PC's usb drivers for the device, or use another computer & install SUTL3 utility from Viewsonic, and see if it can at least beep & signal some USB sequence loading the drivers.
Here's a link to Droid Explorer posted elsewhere in XDA (instead of pointing you to "Search" for it) Install it if you can get the yours powered on, but use it with care as it's a very "powerful" tool to explore all the hidden workings of the Android device(s).
http://forum.xda-developers.com/showthread.php?t=558108
My feeling is that the core image & boot file(s) were corrupted, damaged & overwritten, and it need to be reformatted & reflashed from a stock *.nb0 file, someone with adb might be able to - maybe, just maybe - rescue it.
Let's see if one of our fellow developers might have a better solution on where to begin b/c this is about as far as I can offer - well, you can always put on eBay for parts & hoped you didn't spend a lot as 2nd. hand.
Uhhh looks like i have no other choice but to have this repaired at service center and pay
Hey guys,
today i got my transformer prime. After the succesfull update to ICS ....11. a camera firmwareupdate was detected.. i downloaded it and installed it... after a restart i stuck @ the bootscreen and cannot go out of it. dont know how to do a fully System reset where i can install on of the updates which i can download from the support site from asus.. Pleas help me. otherwise i have to send my device back to amazon.
My input-
On the next boot, hold volume down.
Tiny text appears, release volume down.
When icons show up, choose factory reset via volume down then volume up.
Hope for the best.
I'd wait to see if anyone else has a solution. I think I've seen this before in another discussion.
_Gir_ said:
My input-
On the next boot, hold volume down.
Tiny text appears, release volume down.
When icons show up, choose factory reset via volume down then volume up.
Hope for the best.
I'd wait to see if anyone else has a solution. I think I've seen this before in another discussion.
Click to expand...
Click to collapse
I have already tried that but it does not help. I have send it back to amazon for fixing it.... I need a full reset where i can flash the completly rom... something like CWM but we are not having it yet cause of the ****ing bootloader...
Ive been messing around with this for a few days now with no luck.
My was acting sluggish a few days back so i restarted it. Well low and behold Im getting the "Starting RSD protocol support" message on top of the dual core logo now.
I've searched around, and have have tried all i can think of. I have SBFed the phone multiple times, using the tutorial here, with no luck.
After SBFing the phone it just returns to the same state.
The battery IS fully charged, so we can rule that out. Maybe, just maybe, the volume toggle is stuck but it clicks up and down with no issues.
Anyone have any ideas? Ive been pulling my hair out on this one. Phone is on Verizon prepaid so its grandfathered in at 95/month UNLIMITED data , and they dont seem to willing to let me switch back to my Droid X or anything else for that matter.
Thanks in advance for anyone with ANY ideas or suggestions.
edit as a side note i have been rooted for 6 months no issue/and am on Eclipse. I had not changed any settings in a few months and had not installed any apps in a few week. This was pretty out of the blue.
My first thought (before I read you had this thought also) was that your volume up button might be stuck. Or the trigger inside anyway. If thats the case, you will probably have to find a way to get that button off but I have no idea if thats possible without breaking your phone. Other than that, I dont know what else could cause it. Especially if you SBF and it still does it.
Try this to see if you have a faulty volume button. Turn the phone off and turn it back on while holding the volume DOWN button. I forget what the first option is but it will say something at the top. first of all, if your volume button is stuck in the up position, it might start whatever the first option is. If not, press the volume down button until you get to Android Recovery. Then press up. If you do this, I'm guessing your volume up button is working as it should. Pressing up will start the recovery. When you see the triangle image, press volume up and volume down at the same time. try wiping cache and data and restart and see if that does anything.
jsgraphicart said:
My first thought (before I read you had this thought also) was that your volume up button might be stuck. Or the trigger inside anyway. If thats the case, you will probably have to find a way to get that button off but I have no idea if thats possible without breaking your phone. Other than that, I dont know what else could cause it. Especially if you SBF and it still does it.
Try this to see if you have a faulty volume button. Turn the phone off and turn it back on while holding the volume DOWN button. I forget what the first option is but it will say something at the top. first of all, if your volume button is stuck in the up position, it might start whatever the first option is. If not, press the volume down button until you get to Android Recovery. Then press up. If you do this, I'm guessing your volume up button is working as it should. Pressing up will start the recovery. When you see the triangle image, press volume up and volume down at the same time. try wiping cache and data and restart and see if that does anything.
Click to expand...
Click to collapse
Yeah, I should have included that, it wont go into recovery by pressing the down button while turning on. Guess it might be the actual switch. Anyone have any ideas on that?
edit And suprise if you hold the up button while turning on you get the RSD support msg! (if its working properly) Its gotta be something hardware at this point. i hope not...
Yeah, if you hold Up while powering on, it will start RSD automatically. If you hold down, it gives you other options to scroll through. It could very well be hardware related if that isnt working. Unless someone else has anything else to say about it.