After an unsuccessful update, the phone was bricked. It cannot be turned on, but when is connected to the PC, the Qualcomm Port 9008 port become active.
Is it possible to unbrick the phone via Qualcomm EDL mode or any other way?
What? What do you mean it cannot be turned on? Even when breaking a samsung phone's firmware, "download mode" should still be active and working. In that case, you have to reflash a whole firmware again. Unfortunately, there's a chance that you will have to give up on your data.
GiulianoB said:
What? What do you mean it cannot be turned on? Even when breaking a samsung phone's firmware, "download mode" should still be active and working. In that case, you have to reflash a whole firmware again. Unfortunately, there's a chance that you will have to give up on your data.
Click to expand...
Click to collapse
I actually found a solution. I left the battery on the phone to be completely discharged. Then I pressed 3 buttons (volume (+), volume (-) , and power) and connect the computer via USB cable with the phone. The phone went into an emergency recovery mode. I tried to use Odin, but didn't work out. After pressing the power button (for 5 sec.) The phone restarts and the update started over.
Nevertheless, thank you.
eternal_optimist said:
I actually found a solution. I left the battery on the phone to be completely discharged. Then I pressed 3 buttons (volume (+), volume (-) , and power) and connect the computer via USB cable with the phone. The phone went into an emergency recovery mode. I tried to use Odin, but didn't work out. After pressing the power button (for 5 sec.) The phone restarts and the update started over.
Nevertheless, thank you.
Click to expand...
Click to collapse
Try entering download mode.
Power off your device.
Press and hold volume up and down buttons at the same time, then connect it to your PC while you still hold them. It will automatically enter download mode.
Flash firmware.
Related
I deleted framework-res.apk by accident instead of replacing it. My phone became unresponsive so I took the battery out and put it back in and once it turned on it gets stuck at the booting logo. I cannot get it into download mode either. I pressed vol up+down and then plugged in the usb. I've also hard reset it pressing the vol + home + power button. I've tried every button combination suggested on the forums and none work. When it connects to my computer it is detected as an MTP and not software/usb. Is there anything I can do to replace the firmware with a stock version? Thank you very much.
Press VolumeUP button and insert USB cable into phone
garik345 said:
Press VolumeUP button and insert USB cable into phone
Click to expand...
Click to collapse
I did this and the phone got into the S/W mode and my computer detects it in the drivers but none of the flashing programs recognize it. I tried using the LG support tool, KDZ flasher, and LGNPST. None of them detect the phone. The LG Support shows the phone in the beginning to show the model and drivers, but once I click update software it can't detect it anymore and crashes. Any advice on how to get stock firmware in this situation?
I cannot turn on device, enter recovery, enter download mode (volume down + power), and phone does not vibrate or have any sign of power. Phone was about 60% when I attempted to flash something and it powered down and bricked my phone..
USAN03 said:
I cannot turn on device, enter recovery, enter download mode (volume down + power), and phone does not vibrate or have any sign of power. Phone was about 60% when I attempted to flash something and it powered down and bricked my phone..
Click to expand...
Click to collapse
What build were you on? What were you trying to flash, and using what tool?
You can usually recover from interrupted flash attempts by rebooting into the downloader.
You're missing part of the downloader boot. Starting from powered down (best to pull battery), hold down home and volume down. Then hold power. When the phone vibrates, release power but continue to hold volume down and home.
Hopefully you can get into download mode and be able to recover.
k1mu said:
What build were you on? What were you trying to flash, and using what tool?
You can usually recover from interrupted flash attempts by rebooting into the downloader.
You're missing part of the downloader boot. Starting from powered down (best to pull battery), hold down home and volume down. Then hold power. When the phone vibrates, release power but continue to hold volume down and home.
Hopefully you can get into download mode and be able to recover.
Click to expand...
Click to collapse
I was running a carbon nightly, twrp, and was trying to flash a kernel.
I did what you listed above, but phone does not vibrate..
Try jtag
Just curious. is it possible? Recently my volume down key suddenly stops working for no known reason. And because my phone's recovery mode is triggered by volume down+power, i cant possibly enter recovery mode because of that problem.
Volume up+power is ok, but that's factory mode. This is a pain for me because if i cant go to recovery, if i got my phone bootloop in the future, i cant fix my phone. And i found one more problem, my pc wont detect my phone too. So basically if i got my phone bootlooped there's no solution to fix it. It only charges but adb and usb connected wont show in my status bar even the drivers is installed in my pc. Seems that two problem is linked.
So is it really possible? I want to make the key combination for my phone's recovery be power button+vol up not power but.+vol down.
And i dont find factory mode useful so i will dispose it.
aeonfox said:
Just curious. is it possible? Recently my volume down key suddenly stops working for no known reason. And because my phone's recovery mode is triggered by volume down+power, i cant possibly enter recovery mode because of that problem.
Volume up+power is ok, but that's factory mode. This is a pain for me because if i cant go to recovery, if i got my phone bootloop in the future, i cant fix my phone. And i found one more problem, my pc wont detect my phone too. So basically if i got my phone bootlooped there's no solution to fix it. It only charges but adb and usb connected wont show in my status bar even the drivers is installed in my pc. Seems that two problem is linked.
So is it really possible? I want to make the key combination for my phone's recovery be power button+vol up not power but.+vol down.
And i dont find factory mode useful so i will dispose it.
Click to expand...
Click to collapse
somebody?
I have tried the power + volume down and plug the usb into the pc and I get to the Modified recovery where you can go into safe mode or factory reset, etc. I have done it before but it was Kingo root that did it. It's not working because I can't get to usb debugging mode. I need to go back to stock. Thanks
kwcummins22 said:
I have tried the power + volume down and plug the usb into the pc and I get to the Modified recovery where you can go into safe mode or factory reset, etc. I have done it before but it was Kingo root that did it. It's not working because I can't get to usb debugging mode. I need to go back to stock. Thanks
Click to expand...
Click to collapse
If you are using the LGUP method, you do not need to even go into download mode. If you are on the Verizon bootlooped screen you should be able to flash it back to stock right then and there.
Also there is no real recovery method that you can use so you will have to wipe it completely clean unless you have backups.
LGup says phone 'unknown' so it won't work. It worked yesterday. Not sure what happened. Tried the battery pull method but it still doesn't work.
mcbeat257 said:
If you are using the LGUP method, you do not need to even go into download mode. If you are on the Verizon bootlooped screen you should be able to flash it back to stock right then and there.
Also there is no real recovery method that you can use so you will have to wipe it completely clean unless you have backups.
Click to expand...
Click to collapse
kwcummins22 said:
LGup says phone 'unknown' so it won't work. It worked yesterday. Not sure what happened. Tried the battery pull method but it still doesn't work.
Click to expand...
Click to collapse
Does it go into the normal LGUP screen or is it something different?
fixed
i recopied the 'common' folder and it worked.malware detector may have deleted files? weird. up and working again. Thanks
kwcummins22 said:
LGup says phone 'unknown' so it won't work. It worked yesterday. Not sure what happened. Tried the battery pull method but it still doesn't work.
Click to expand...
Click to collapse
I had the same issue with my VS990. LGUP was not seeing the phone. Using the Recovery menu via power + volume down, I booted my phone into USB debugging mode. LGUP was then able to recognize my phone. I then chose the tot file, chose upgrade instead of refurbished, and clicked start. It auto restarted my phone into Download Mode and started the upgrade. If you can get the phone into USB debugging mode, you'll be set.
kwcummins22 said:
I have tried the power + volume down and plug the usb into the pc and I get to the Modified recovery where you can go into safe mode or factory reset, etc. I have done it before but it was Kingo root that did it. It's not working because I can't get to usb debugging mode. I need to go back to stock. Thanks
Click to expand...
Click to collapse
Plug a USB cable into your phone with your phone powered off, hold down on the Vol Up button and plug the USB cord into your computer. It should immediately boot into download mode. I have verified this works on my Verizon V10.
rustypie said:
Plug a USB cable into your phone with your phone powered off, hold down on the Vol Up button and plug the USB cord into your computer. It should immediately boot into download mode. I have verified this works on my Verizon V10.
Click to expand...
Click to collapse
I just confirmed that works good job
Huh. I did mine from a regular boot up, but in debug mode. LGUP commanded it to reboot into DL mode for me.
Download mode on the LG V10 is achieved the same way all other recent LG smartphones have been. Power the device off completely by either the power menu or battery pull. Plug your USB cable into your computer. I didn't have an issue with USB 3.0. Hold Volume up and plug in the phone to the computer. Keep holding Volume up until the phone says download mode. It will do a small loading screen then it will change, this is normal. You can leave download mode by pulling out the battery or by holding the power button for 10-15 seconds.
bantzt said:
Download mode on the LG V10 is achieved the same way all other recent LG smartphones have been. Power the device off completely by either the power menu or battery pull. Plug your USB cable into your computer. I didn't have an issue with USB 3.0. Hold Volume up and plug in the phone to the computer. Keep holding Volume up until the phone says download mode. It will do a small loading screen then it will change, this is normal. You can leave download mode by pulling out the battery or by holding the power button for 10-15 seconds.
Click to expand...
Click to collapse
YOU SIR! Are the ONLY person to GET IT RIGHT! BINGO! Thank YOU!
hi
pls can someone help me? my lg-h901 can't boot into bootloader mode i have tried everything still not working, volume down + power on it reboot to normal, volume down + usb cable plug into pc it saw battery icon and reboot to normal, volume up and down + usb cable plug into pc nothing. i will be very great full if someone tell me what to do thanks in advance
achuho said:
hi
pls can someone help me? my lg-h901 can't boot into bootloader mode i have tried everything still not working, volume down + power on it reboot to normal, volume down + usb cable plug into pc it saw battery icon and reboot to normal, volume up and down + usb cable plug into pc nothing. i will be very great full if someone tell me what to do thanks in advance
Click to expand...
Click to collapse
I think you might be doing it wrong...
Download Mode -> Hold volume up, and plug into usb while STILL holding volume up, release once in download mode
Reset Screen -> Hold volume down + power, then plug into usb whil holding down buttons, release when screens comes on.
Ok, now for my problems. I got my phone into DM, used LGUP to install VS99026A_00_0118.kdz on my VS990. I let it go overnight. Came back to see it failed at about 73%, Error "can't get laf property", ever since then I can't get back into DM again, my LG splash screen will come up, then I get the android guy saying "Erasing...", then it reboots to splash screen again, waits a sec, then turns off. I managed to get into the reset screen with vol dn + pwr + usb method, tried to go into safe mode, now I have same issue getting back to that screen too.
Any help?
my lg v10 stops at download mode screen and don't go furhter
I have a V10 stuck in the bootloop. I was able to get it to boot past the lg screen 1 time but it very quickly rebooted again and is still stuck. And when I try download mode using LG Bridge, my computer says "no phone connected" and my phone stays on the "Download Mode" black screen. How can I fix it?
Tannerlini said:
I have a V10 stuck in the bootloop. I was able to get it to boot past the lg screen 1 time but it very quickly rebooted again and is still stuck. And when I try download mode using LG Bridge, my computer says "no phone connected" and my phone stays on the "Download Mode" black screen. How can I fix it?
Click to expand...
Click to collapse
i have same problem please help
my computer says "no phone connected" and my phone stays on the "Download Mode" black screen. How can I fix it?
I tried to root my phone by magisk.
After flashing a patched boot.img, it's failed to boot into system and I got a message that "the device need factory reset". I clicked yes and everything seems ok,I can boot into system. Then I tried to flash img again. So I boot into bootloader. Unfortunately, this time I got a black screen. The phone doesn't response me anymore.
I tried the software repair in xperia companion but It cannot dected my phone when I hold on volume down and plugged in it. I also tried hold on volume up + power but nothing happened. Hold on power key also no response. The led light always black, only become red when I connect it to my pc.
What should I so now and what's my phone's status? I searched something about 9008 mode and edl but I don't know how to check whether my phone is really turn into that status, my pc cannot dect my phone.
Have the same problem, only with the 5 iii instead. Still looking for a fix.
Try to switch the phone off; then just plug it into your PC without holding the Vol- key. It has happenned a couple of times with me that the phone does not want to boot up, with attempts to get it into FLASH mode by holding the key down throwing more confusion into the mix.
I think there is a low battery protection. Make sure the phone is charged up. Keeps the device from death during a flash.
Red led mean a very low battery. Keep it plugged (not to PC but to power adapter) for 2-3 hours and then try again a force reset.
Never, never try flash or other stuff under 50% battery
Also force restart is keep pressed vol+ and power button (or vol- and power button) till you fell a vibration.
Try this after a good charge
Evil_Sephiroth said:
Red led mean a very low battery. Keep it plugged (not to PC but to power adapter) for 2-3 hours and then try again a force reset.
Never, never try flash or other stuff under 50% battery
Also force restart is keep pressed vol+ and power button (or vol- and power button) till you fell a vibration.
Try this after a good charge
Click to expand...
Click to collapse
It might require experimenting with service modes and different chargers. I had an early Xperia 1 III that bootlooped while charging after setting up the fingerprint reader. It seems that charging is disabled during booting. It has to finish or enter a service/fault mode.
my phone is having this after doing fastboot --slot=b reboot recovery (which actually I had to do fastboot --set-slot=b and then fastboot reboot recovery). the notification light blinks red. have tried vol up + power, vol down + power, and vol up + down + power for like 30 seconds and nothing
tomatoketchup said:
my phone is having this after doing fastboot --slot=b reboot recovery (which actually I had to do fastboot --set-slot=b and then fastboot reboot recovery). the notification light blinks red. have tried vol up + power, vol down + power, and vol up + down + power for like 30 seconds and nothing
Click to expand...
Click to collapse
I feel sorry for you brother...such a nice device...OK let's talk what happened, the state now your device is in is called hardbrick and it had a corrupted bootloader or no boot loader, but your device is still alive, in your PC in device manager it lists as Qs USB mode with some number after it like qsusb9008...now this device can only be brought to life with the help of a blankflash file which can flash your boot loader in snapdragon service mode...actually no snapdragon can be hardbricked permanently now you need appropriate blankflash file for your device.. Please don't open the device if some repairmen suggests to do JTAG nothing is necessary all you need is blankflash file which is shared to only Sony testers groups.... Who tests ROMs before release and they hardbrick so they share those files to them.... Please don't loose hope....it takes time but certainly it can be bought back to life... And dont try any flashing utility as there is no functional boot loader on it now and nothing will work...Sony won't provide that for sure and they will say then can only solve by mother board replacement ,don't believe therm your device is perfect it only needs blankflash file as it entered into final safe mode... I ain't regular on XDA if you need any info contact me via my mail [email protected] g ma I'll .com
Have any of you tried this - https://developer.sony.com/develop/open-devices/get-started/flash-tool/download-flash-tool/
ok in my case it was the charging IC