Hello everyone, I hope to find some help here regarding the bluetooth connection on the console of my car. Since the Oos 11 version, the network reception indicator on the console remains fixed. I no longer have the reality of network reception, whereas on Oos 10 it worked very well. Would there be a manipulation to do to rectify this concern. Thank you
Related
Hi,
I have an unlocked HTC hero from orange. It is having some strange problem relating gps(global positioning system). The gps works extremely well when I am connected to network through 2g network but do not works at all when I am connected through 3g. I don't see any relationship between them also I can use gps in airplane mode but can not use it when there is no sum inserted. What I think is that as the phone share common gps, 2g and 3g chip when the phone turns off 2g radio it also turns off the gps chip. Is somebody else experiencing the same problem. I also reset the device but problem persists. Is there something I can do. Is it hardware fault or bug in the software considering gps is working very fine on 2g. I currently have latest genuine Rom from orange so cannot try changing the Rom.
Thankyou
Arpit
I know this question has been asked a lot of times, but I just want to know if this is a hardware problem that will always be here, or if this is a software bug.
My WiFi signal strength is full if I'm directly next to my router. For every step I take, I loose 1 stripe. So if I'm 5-6 meters awy from ym router, I don't have a signal at all. This is not my router, I've tested it with 2 other routers and a number of AP on campus - all the same problem.
I have the latest CM 11 spyder nightly build, I tried to disbale 5GHz (without any luck). My "Avoid poor connections" is obviously disabled. I deleted everything in data/misc/WiFi and also tried running wifical.sh without any improvements.
Does anyone know why this happens? Is there and fix/patch for this?
I am also having this same problem.
Find a fix yet?
Solved
Hi,
I found a way to fix it, days ago I changed the loud speaker of my xt916 , and after this my signal of wireless don't pass one bar, so I open him again and forced the two contacts beside the speaker to take a higher and lean better in the antenna's contact. After this my wirelles take the 3-4 bars as well.
Sorry about the English, i'm learning.
I recently purchased an Xiaomi Redmi Note 3 Pro phone (kenzo), it covers all the bands that rogers uses in my area in Canada, I believe.
https://en.wikipedia.org/wiki/Rogers_Wireless
I can connect with the phone on LTE, HSPA+ with no problem, if available. Sometimes, if I am in certain area's, the signal indicator drops to 3G .... it shows a decent signal, but no calls or data can go through.
In this example on the following chart, the first WCDMA connection,my phone only indicates 3G and I can not make a call or use data. When my call attempt is done, it goes back to LTE. Then I try again. Then for the second WCDMA connection on the chart, I am connected as H+, I can make a call and use data. Whenever this phone connects to CID 31072 the problem happens. When I connect to CID 31075, no problem. These are just examples of towers that I reach from my home. I get the same problem occuring other areas.
Any suggestions on what I need to change on my phone? Is my phone making a kind of 3G connection for some reason, which Rogers doesn't support? I have tried everything I can think of, Miui dev versions, CM13, LineageOS 14.1 etc, change Android Radio Menu settings, etc.
Nothing seems to fix this issue.
Any advice would be greatly appreciated!
I have been using Network Signal Guru, and have figured out that the phone will connect calls data on 3g if the band it finds is B5-850M .... if the tower tries to connect to is B2-PCS-1900 the call fails.
I tried to block the use of band 2 with Network Signal Guru, but it seems to still use it when it finds it.
I have since flashed a LineageOS rom and used the Network Signal Guru to disable band 2 WCDMA. The phone has not been experiencing the issue at all since. I am cautiously optimistic that I have found a solution. Still not sure why this band doesn't work here though.
Hello there! Two-three days ago I installed Lineage OS 14.1 20170907 build on my Oneplus two, but I am facing network fluctuations on the jio sim i.e. for a moment the network is full and the next moment the network is on one bar in the same spot. There is no drop in network but battery drain can be observed due to this. From what I am guessing, it is constantly searching for networks even though I have put in on LTE only mode. Is there a solution to this? If so, it would be very helpful!
Thanking you in advance!
Hello all,
I started to have some problems with signal strength.
It's not ROM-related (currently the newest CrDroid).
If I cut my WiFi and set the phone to prefer LTE signal sometimes I'm not able to use data. It's constantly switching between LTE / LTE+.
Sometimes it will connect and it's fine but most of the time it isn't.
It only happens in places when the signal is poor.
If I set the phone to prefer 3G it works perfectly normal.
My gf got the same phone and didn't experience that issue.
I believe that for some time after I received this phone it worked normally.
Maybe it's firmware related issue?
I heard about an issue with the poor signal on this phone...
Thank You in the advance for your answers.