I have a Redmi 5 plus(Vince) device in which I have flashed custom ROM. In case of Androis 10 based custom ROM it is working perfectly. Currently I have Pixel Experience Plus android 10 installed. But if I try to install any custom ROM based android 11,12 or 13 then the device is stuck in boot animation. I don't know what I am doing wrong. I am wiping the Delvik cache, Cace and data then flashing the rom and then rebooting. Please someone help me.
You must be on Latest firmware v11.0.3.0 or v11.0.2.0
or try to formata data type yes.
NOSS8 said:
You must be on Latest firmware v11.0.3.0 or v11.0.2.0
or try to formata data type yes.
Click to expand...
Click to collapse
Yes it's working. Now I am using Spark Os 13. Thanks a lot
Related
when i install cyangenMod 13 it freeze at:
Patching system image unconditionally
i use twrp 3
--------------------
cyangenMod 12
same problem
-------------
only cyangenMod 11
works
Did you have the original Kit Kat firmware before you tried the newer CM roms? If you started upgrading from Jelly Bean, then that's why.
i use odin to install official 4.4 rom
then install twrp
but still same problem
thank you
@prowm
What I would suggest you is to use CWM Recovery. Also be sure to do a full wipe before, where I don't think that this was the problem here
Or TWRP 2.8 as the older version hadn't any issues with any rom (for me at least ))))
TimurAlaskara_TR said:
@prowm
What I would suggest you is to use CWM Recovery. Also be sure to do a full wipe before, where I don't think that this was the problem here
Or TWRP 2.8 as the older version hadn't any issues with any rom (for me at least ))))
Click to expand...
Click to collapse
Previously I did not have any problem used cyangenmod 12 and 13
But now I do not know the problem occurred caused
Experimented twrp 2.8 and twrp 3
i do full wipe davlik cashe and data , system
but still same problem
thank you for your reply
prowm said:
Previously I did not have any problem used cyangenmod 12 and 13
But now I do not know the problem occurred caused
Experimented twrp 2.8 and twrp 3
i do full wipe davlik cashe and data , system
but still same problem
thank you for your reply
Click to expand...
Click to collapse
Try cwm anyway a completely different recovery may prevent that issue
TimurAlaskara_TR said:
Try cwm anyway a completely different recovery may prevent that issue
Click to expand...
Click to collapse
test cwm but same issue
Please link to the recovery and rom you're trying to use.
es0tericcha0s said:
Please link to the recovery and rom you're trying to use.
Click to expand...
Click to collapse
when updating partition details
faild to mount system/ ( invalid argument )
i test many roms
cm13
http://forum.xda-developers.com/gal...m-13-0-ms013g-cyanogenmod-13-grand-2-t3299635
recovery
http://forum.xda-developers.com/gal...recovery-twrp-2-8-6-0-touch-recovery-t3107535
roms ok :
ROM OS Version: Lollipop
ROM Kernel: Linux 3.4.x
Based On: TouchWiz
http://forum.xda-developers.com/galaxy-grand-2/development/rom-motion-rom-ll-t3295055
and
http://forum.xda-developers.com/galaxy-grand-2/development/rom-adityarom-v3-0-t3387388
and
cm11
http://forum.xda-developers.com/gal...lopment/alpha-cm-11-0-galaxy-grand-2-t2972750
Did you wipe system when switching roms? Also, you can try mounting system in TWRP / mount
es0tericcha0s said:
Did you wipe system when switching roms? Also, you can try mounting system in TWRP / mount
Click to expand...
Click to collapse
i wipe system and data
problem solved
i install first cyangenmod 13 then install newer
thanks for all
Hi!
I flashed CM 13 on my RedMi 3, after some weeks I wanted to go back to XiaoMi.EU MiUi so I wiped dalvik, cache, data and system partitions then I restored the backup but it didn't boot up (it showed Mi logo then it reboots); I tried to make a clean flash but it still didn't boot up.
I flashed latest china developers firmware but it didn't boot up too; I tried with global developers and I found that the bootloader has been blocked (I don't know why), I unlocked it and tried again but it still didn't boot up.
I tried to flash vietnamese unbrick firmware but it stil didn't boot up.
I reflashed CM 13 but it doesn't boot up.
What's happened? I ran out of ideas. :silly:
Sorry for my bad english.
try this:
http://en.miui.com/forum.php?mod=redirect&goto=findpost&ptid=342268&pid=6219442
retakal said:
try this:
http://en.miui.com/forum.php?mod=redirect&goto=findpost&ptid=342268&pid=6219442
Click to expand...
Click to collapse
It didn't work. Thanks anyway.
After a lot of experiments I got CM 12.1 working; unfortunately it's the only one ROM that boots. :|
@Anik_khan: Have you ever tried to go back to MiUi from CM 13?
EDIT: Sometimes when I try to turn it off it reboots and sometimes it reboots 5/6 times before boot up.
I tried to flash English unbrick ROM and XiaoMi.EU fastboot ROM too but they don't boot.
On CM 12.1 audio doesn't work. I start thinking that's an hardware fault because I tried all possible solutions.
I tried latest @Anik_khan's CM 13, latest XiaoMi.EU weekly and FlyMe too but they don't boot (on CM 13 I don't even see bootanimation). If I flash a custom Kernel (for example MYKernel) on CM 12.1 it doesn't boot anymore.
I suggest you to go to Mi service center.
Hi,
I've got a RN3, snapdragon version, 3GB of RAM. Unlocked bootloader. TWRP 3.0.2-2
I've been using CM for a while, android 6.0.1 and I've been trying now for a few days to move to Nougat.
I've tried different roms: NitrogenOS, lineage OS, resurrectionRemix.
I've also tried flashing different versions os miui firmware: 7.3.16, 7.3.23, 7.3.30
So, after all that, the result is always the same. The flashing seems successful, the phone boots but then I cannot go through the initial setup screen.
I choose the wifi network but when I try to enter the password, the screen resets every 5 seconds or so. I know it's resetting/reloading because the password I've typed so far goes away and I have to start again. It happens every few seconds and I cannot setup wifi properly.
I tried changing the password to aaaaaaaaaa to make it easy and quick to setup. Once I go through that, it stays for ever in the next screen "checking information" (or something like that). Again, it seems to be reloading this screen every few seconds.
is there something am I missing? Maybe I'm flashing firmware/rom in the wrong order?
I'm back with android 6.0.1 now and the phone works fine.
thanks in advance for your help.
Flash Kenzo Firmware , Rom & Nougat Gapps not MM , next reboot system
Sent from my Redmi Note 3 using Tapatalk
VaibhavKumar07 said:
Flash Kenzo Firmware , Rom & Nougat Gapps not MM , next reboot system
Sent from my Redmi Note 3 using Tapatalk
Click to expand...
Click to collapse
thanks @VaibhavKumar07
so, this is exactly what I've tried a few times.
what about wipes and all that stuff?
I don't mind doing a clean install and reinstalling/reconfiguring everything.
I've tried different things, but for example what is mentioned in the thread "CM13/14/14.1/AOSP N firmware for KENZO/KATE [VoLTE][12.1.2017]"
-Reboot to TWRP recovery
-Flash firmware
-Factory reset (data, cache and dalvik-cache)
-Flash your favorite Marshmallow or Nougat ROM
-Reboot your phone
is that still valid for the nightly builds from April 2017?
On Cm firmwares I was unable to get VoLTE working so recommend you to flash Miui beta firmware search in SD Rom or guide section you'll find em if not message me again .
Regarding procedure :
- First flash Twrp 3.1.1.0 from official site cuz that's latest
- Next go & wipe check everything except SD card & OTG
- Flash Firmware
- Flash Rom
- Flash Gapps Arm *64 Android N from Open apps
- Flash Any Add-ons if required like kernel or Sound enhancement mods ( optional )
- Clean cache/dalvik cache
- Reboot
Mention the Rom you're flashing!
Sent from my Redmi Note 3 using Tapatalk
So, I did all that several times, except for flashing the latest twrp version. I'm on 3.0.2-2 because it flashes ok but when rebooting it's back to 3.0.2-2. I'm doing this from fastboot. I'm not only loading, but flushing. It seems to be ok but then it's gone after reboot.
Anyway, I've tried this procedure with 3 different roms:
ResurrectionRemix
LineageOS
Nitrogen OS
flashing latest versions for each rom.
Could the twrp not updating properly have something to do with this issue? does the latest version fix some flashing issues with Nougat?
the thing is that if flashed and boots, but it doesn't run properly as mentioned.
I will try to get latest twrp version working and report back if that makes any difference.
VaibhavKumar07 said:
On Cm firmwares I was unable to get VoLTE working so recommend you to flash Miui beta firmware search in SD Rom or guide section you'll find em if not message me again .
Regarding procedure :
- First flash Twrp 3.1.1.0 from official site cuz that's latest
- Next go & wipe check everything except SD card & OTG
- Flash Firmware
- Flash Rom
- Flash Gapps Arm *64 Android N from Open apps
- Flash Any Add-ons if required like kernel or Sound enhancement mods ( optional )
- Clean cache/dalvik cache
- Reboot
Mention the Rom you're flashing!
Sent from my Redmi Note 3 using Tapatalk
Click to expand...
Click to collapse
so, still fighting with this.
i managed to upgrade to twrp 3.1.0-1, all good.
however, i still have the same problem with the initial screen, it keeps reloading every few seconds and can't finish the setup or even skip it.
i've tried different versions of firmware. I've also tried flashing the latest miui rom (dev and global) and then a custom rom.
i've tried different builds (different dates) of the following roms:
nitrogenOS
lineageOS
aospextended
mokee
resurrectionremix
exact same behaviour with all these roms.
what am I doing wrong? i'm on marshmallow and everything works fine, but stuck moving to nougat. do I have to flash something not mentioned already to move from custom MM to custom Nougat?
txutxe said:
so, still fighting with this.
i managed to upgrade to twrp 3.1.0-1, all good.
however, i still have the same problem with the initial screen, it keeps reloading every few seconds and can't finish the setup or even skip it.
i've tried different versions of firmware. I've also tried flashing the latest miui rom (dev and global) and then a custom rom.
i've tried different builds (different dates) of the following roms:
nitrogenOS
lineageOS
aospextended
mokee
resurrectionremix
exact same behaviour with all these roms.
what am I doing wrong? i'm on marshmallow and everything works fine, but stuck moving to nougat. do I have to flash something not mentioned already to move from custom MM to custom Nougat?
Click to expand...
Click to collapse
Try this once (Clean) :
Flash Nitrogen
Reboot
Flash gapps and firmware.
Hope it may work for you.
U have to install playstore by Google installer
Miui China developer rom for redmi 3s- http://bigota.d.miui.com/7.8.28/miui_HM3S_7.8.28_bcce15b673_6.0.zip
Tell us about performance nd how good 9 is frm 8
Chances are high that either xiaomi eu or multirom will release this china rom soon with google apps preinstalled.
Link is broken
Sent from my Redmi 3X using Tapatalk
How to update Redmi 3S Prime to miui 9 7.8.28? This version is not showing in miflashtool
Bhavesh_L said:
How to update Redmi 3S Prime to miui 9 7.8.28? This version is not showing in miflashtool
Click to expand...
Click to collapse
This is a nightly build. Just for closed Beta Team actually. It is forbidden to leak the download link
But if you want to install it, use custom recovery, such as Twrp official or unofficial. Wipe dalvik, cache, system and data..
Then flash the rom you just downloaded.
Reboot into your twrp once again. It is important to avoid bootlooping. And go to advance > disable dm-verify or flash lazy flasher > reboot into system.
Done.
Rukijo said:
This is a nightly build. Just for closed Beta Team actually. It is forbidden to leak the download link
But if you want to install it, use custom recovery, such as Twrp official or unofficial. Wipe dalvik, cache, system and data..
Then flash the rom you just downloaded.
Reboot into your twrp once again. It is important to avoid bootlooping. And go to advance > disable dm-verify or flash lazy flasher > reboot into system.
Done.
Click to expand...
Click to collapse
DONT wipe system and data.You need to dirty flash from latest miui developer.
fxsheep said:
DONT wipe system and data.You need to dirty flash from latest miui developer.
Click to expand...
Click to collapse
wiping everything and flashing both rom + lazy flasher will boot fine. tested by myself
Official Global beta miui 9 7.9.8 !!
Download
http://en.miui.com/download-303.html
ghemanth said:
wiping everything and flashing both rom + lazy flasher will boot fine. tested by myself
Click to expand...
Click to collapse
I do too but stuck at mi logo .
fxsheep said:
I do too but stuck at mi logo .
Click to expand...
Click to collapse
Twrp recovery, and format data
Sent from my Redmi 3S using XDA-Developers Legacy app
[email protected] said:
Twrp recovery, and format data
Click to expand...
Click to collapse
Oh ,yes.I mistakenly wiped system.
How to go back to MIUI A10 based ROMs from OSS Vendor based ROMs without losing decryption and data:-
* Requirements: Decrypted Storage (if not Decrypted Format data before doing those steps), MIUI A10 Stock ROM, Orange Fox Recovery (TWRP didn't work very well for me) and DFE (attached)
* Steps:-
1. Wipe data, cache, dalvik cache
2. Flash MIUI ROM
3. Reboot recovery
4. Wipe data, cache, dalvik cache
5. Flash MIUI vendor based rom
6. Reboot recovery
7. Flash dfe
8. Reboot to system
Voila! Now you have your data as well as decrypted storage
Thank me later xD
Nice one. Thanks!
Suraj Pandey said:
How to go back to MIUI A10 based ROMs from OSS Vendor based ROMs without losing decryption and data:-
* Requirements: Decrypted Storage (if not Decrypted Format data before doing those steps), MIUI A10 Stock ROM, Orange Fox Recovery (TWRP didn't work very well for me) and DFE (attached)
* Steps:-
1. Wipe data, cache, dalvik cache
2. Flash MIUI ROM
3. Reboot recovery
4. Wipe data, cache, dalvik cache
5. Flash MIUI vendor based rom
6. Reboot recovery
7. Flash dfe
8. Reboot to system
Voila! Now you have your data as well as decrypted storage
Thank me later xD
Click to expand...
Click to collapse
Can you please provide link to miui stock rom?
https://xiaomifirmwareupdater.com/firmware/surya/stable/V12.0.9.0.QJGMIXM/
Would this fw work?
ramnoob said:
Can you please provide link to miui stock rom?
https://xiaomifirmwareupdater.com/firmware/surya/stable/V12.0.9.0.QJGMIXM/
Would this fw work?
Click to expand...
Click to collapse
Not fw you'll have to flash the whole rom.
You can flash any Android 10 MIUI ROM (Except Elite) . I used MIUI pulse in my case.
Suraj Pandey said:
Not fw you'll have to flash the whole rom.
You can flash any Android 10 MIUI ROM (Except Elite) . I used MIUI pulse in my case.
Click to expand...
Click to collapse
Can you please give me link?
ramnoob said:
Can you please give me link?
Click to expand...
Click to collapse
Here you go. Download the one meant for your region
Xiaomi Firmware Updater
The ultimate script that provides firmware packages for Xiaomi devices.
xiaomifirmwareupdater.com
Ok, im on A11 PixysOS v4.0.6. Can i move back for MIUI Rom with this method?
i tried this method but my device reboots to recovery
can't boot into system
tried all available recoveries(TWRP,OFOX,PBRP)
PUMPU said:
Ok, im on A11 PixysOS v4.0.6. Can i move back for MIUI Rom with this method?
Click to expand...
Click to collapse
You can go back to MIUI ROM but you'll lose data and storage will get encrypted.
antarix said:
i tried this method but my device reboots to recovery
can't boot into system
tried all available recoveries(TWRP,OFOX,PBRP)
Click to expand...
Click to collapse
Which ROM and which recovery did you try first?
safest method i to use Miflash without locking then install TWRP then your desired Custom MIUI ROM
leinadark said:
safest method i to use Miflash without locking then install TWRP then your desired Custom MIUI ROM
Click to expand...
Click to collapse
And lose your data as well lol. Read the heading.
My guide is about how to revert back without losing data for people who don't wanna lose data