Hi.
I tried flashing a rom on a H96 Pro Plus 3+32GB box with an Amlogic S912, chip.
First couple of times when i tried flashing, it went up to 3-4% and gave out an error. Then i unchecked the erase flash and erase bootloader options and it went to 8% and then gave out an error once again.
After a couple of tries with the erase bootloader and erase flash options. It succeded flashing. But when i plugged in the box. There was no picture, there was just a blue light on the box.
The computer won't recognize the box after that, i've tried putting a rom on a SDcard, i've tried shorting some pins, not sure if they were the correct ones, but no luck. There is power going to the box, the blue light is on, but it won't turn on or display any signal.
Please help!
Thanks in advance!
Hi if you just search u would find the answer faster than writing this thread
anyway
hopefully it will help
other wise you should give more detailed and explained info
mazjed said:
Hi if you just search u would find the answer faster than writing this thread
anyway
hopefully it will help
other wise you should give more detailed and explained info
Click to expand...
Click to collapse
Hi.
Trust me i've searched for a week without any success. Unfortunately the video didn't help me since my problem currently is that the box is getting power but there is no hdmi signal, nor the box is getting recognized by the pc after flashing the rom.
Thanks for trying to help.
then the only chance you have is the short method
mazjed said:
then the only chance you have is the short method
Click to expand...
Click to collapse
Hi
I tried shorting pins, like in the tutorial but nothing happened. Not getting recognized still.
Hi
Ok, so i've fixed the tv box and it turns out i was doing something wrong. I didn't have power plugging it in. I was relying on the usb connection to give enough power to the box. I've done this to get back the box. Please if you don't know what you are doing, get someone that really knows. I'm not responsible for any damage that may happen. This is just what i've done to recover the box.
1. Hold the reset button on the box
2. Plug in USB in the pc and in the box
3. Wait 2 seconds and then plug in power.
4. Hold the 5th and 6th pin (i think). Please watch the video andmake sure that you know what you are doing, since 1 bad move could render the box totally unusable. Thanks. you should hold the pins for a couple of seconds and it should pop up
Also i wasn't able to install Aidenrom (while flashing it gives out an error) or Atvexperience (it cant get imported by usb burning tool)
I reinstalled the default rom. And i was using USB Burning Tool V 2.0.8
Thanks for your help.
Related
Here is the problem:
My phone is stuck on the screen you see immediately after pressing the power button, which has a big "Vibrant" and a smaller "Samsung" both white on black. Whatever I do, it won't get past that.
Here is what happened:
- I had Eclair on it for a long while, and updated to Froyo via Kies, also a long while ago. Then, tired of bad performances, I followed a tutorial to install ICS on it. It worked fine for a month and I was very pleased of the newly gained performances. However this week, (while I was on vacation away from my computer and even internet in fact) it started giving me messages saying something about "Memory low, close some applications" (paraphrasing), even thought my memory indicator said that I was using around 160 MB, which should not be that bad. Then, after a couple of hours like that, applications started to crash (because of low memory I assume). I killed applications not that useful, but it did not change the message. Then, the core application also started to crash, whatever I did. I rebooted several times to get it to start fresh, but as soon as I booted, I got the low memory message and the core crashing. At one point, it would get stuck on the ICS 3D flying boot scene, and not past that.
- So, I rebooted in recovery mode and tried to see if I had an option to just restore part of the ROM so I could use my phone anew. I wanted to avoid restoring it completely since I did not have the information about my APN (I have the T-Mobile Vibrant, but I live in Canada and I'm on Videotron's network), and performances before ICS where really bad (lagging, freezing, name it). Also, I figured it was only a booting problem, so (biggest mistake is here I believe) I tried to restore the boot only. I found somewhere in the advanced options of Clockwork an option to restore parts of the backed-up ROM. So I did it, but I got an error saying something about the checksum I think. There I realized that I was trying to restore an Eclair boot backup to an ICS ROM, so the checksum error probably came from that. I try it a second time... same result. Then, when I rebooted it stopped at the Vibrant screen I described above.
What I tried to resolve it:
- Tried to go back to recovery mode by holding the three buttons as usual. Cannot get in. The only thing that "works" is that if I hold the power button for 6-8 second, it will reboot. And get stuck at the same place.
- Search intensively on the web to see if anyone had the same kind of issue. Saw a lot of the "Exclamation mark bricked" type, resolved by going in recovery mode. Not useful to me.
- Tried to connect it to my computer and see where I could go from there. I am unable to mount the device. If the phone is powered down, as soon as I connect it, it starts to boot (and get stuck you know where). Windows does not recognizes the device, and gives me the message "This device cannot start. (Code 10)". I tried to use the drivers from ADB and those from Kies with the same results.
- I tried to install Android Debug Bridge, but without the phone mounted, it doesn't work.
- I tried to see if Odin would detect it, with the same results
- I tried to pray, but there is no answer there yet. :crying:
So here I am, with the following things still untried:
- I would try the "resistor" way of booting in download mode it that could help. However, I don't have soldering iron, don't know how to solder and don't have the parts required, so that would take me a lot of time just the try this option, without any clue that I would resolve my problem with this. I am willing to go that way if I am pretty sure it will work
- I haven't tried using the Riff Box, and I have no idea what it is and where it would get me. I would not even know where to get access to that.
On a final note, this is my only phone in the house, and to make the matter worse, I changed providers with this phone, so my older cell phones don't work with Videotron's SIM card... I would rather have the issue resolved fast if possible, because otherwise, I'll have to buy a new phone. Let's say that I would have better uses for that cash, so I hope it does not come to that.
So that concludes my sad story for today.
Any clues welcome. If the answer is "get a new phone", I would rather do it that trying stuff for two weeks and having to buy a new phone anyway.
Try reinstalling the drivers and add the nexus drivers since some people report that you may need it. Then get into download mode for Odin, on my phone its both volume buttons, but now power, then keep holding while put the USB in. The pit and pda and reparation should be selected, since that's what I do.
Sent from my SGH-T959 using xda app-developers app
pbeaumont said:
- I would try the "resistor" way of booting in download mode it that could help. However, I don't have soldering iron, don't know how to solder and don't have the parts required, so that would take me a lot of time just the try this option, without any clue that I would resolve my problem with this. I am willing to go that way if I am pretty sure it will work.
Click to expand...
Click to collapse
This method should work for you, what your talking about is called a "USB Jig". You can buy one for around $5 online, I would recommend www.mobiletechvideos.com to buy from. Before you buy the jig I would try booting into download mode with the gingerbread button combos just in case you somehow installed them. Download mode is volume + and power button. Recovery is volume - and power.
Sent from my SGH-T959 using Tapatalk
iKoolkid said:
Try reinstalling the drivers and add the nexus drivers since some people report that you may need it. Then get into download mode for Odin, on my phone its both volume buttons, but now power, then keep holding while put the USB in.
Click to expand...
Click to collapse
I uninstalled and reinstalled the drivers several times, to no effect. In fact, whatever driver there is, it does not matter since Windows always give the message about device not able to start. So I just can't use Odin.
iTz KeeFy said:
This method should work for you, what your talking about is called a "USB Jig". Before you buy the jig I would try booting into download mode with the gingerbread button combos just in case you somehow installed them. Download mode is volume + and power button. Recovery is volume - and power.
Click to expand...
Click to collapse
I just tried the gingerbread combo buttons, but no more results. I will try to get a Jig assembled asap, it would still be faster than ordering it and waiting 10 days to get it. I'll let you know how it goes.
I went and made myself an USB Jig and tada!, it worked!
So I'll now reinstall something with Odin and report a last and final time to confirm everything went right.
Many thanks guys!
Still no joy, I now only get the following message while connection the phone to the computer "windows has stopped this device because it has reported problems. (code 43)". I tried to use the drivers from Kies, the ones from ADB (unsigned, therefore cannot install them on my Windows 7 x64).
Tried to uninstall, then reinstall. Rebooted and reinstalled, and finally tried every USB port on my computer. Always the same result. Anyone has a clue?
Will try tomorrow on the computer @ work...
pbeaumont said:
Still no joy, I now only get the following message while connection the phone to the computer "windows has stopped this device because it has reported problems. (code 43)". I tried to use the drivers from Kies, the ones from ADB (unsigned, therefore cannot install them on my Windows 7 x64).
Tried to uninstall, then reinstall. Rebooted and reinstalled, and finally tried every USB port on my computer. Always the same result. Anyone has a clue?
Will try tomorrow on the computer @ work...
Click to expand...
Click to collapse
Have you tried a different usb cable?
Sent from my SGH-T959 using Tapatalk
Tried it on a different computer, with a different USB cable. Both cables and computer used to work to connect the phone.
I am at a loss for options to try right now... Any suggestion?
Just to clarify, if Odin is up and you connect your phone to the computer, does Odin give you a com port?
sent from my magic box to yours
samsgun357 said:
Just to clarify, if Odin is up and you connect your phone to the computer, does Odin give you a com port?
sent from my magic box to yours
Click to expand...
Click to collapse
Nope, not at all. The OS never gets to the point where it detects correctly the phone and mounts it.
First thing I have to ask is do you have a stock front facing camera?
sent from my magic box to yours
samsgun357 said:
First thing I have to ask is do you have a stock front facing camera?
sent from my magic box to yours
Click to expand...
Click to collapse
^^^You learn fast my friend. I'll hit you up a bunch of thanks later on when I get off work. I've hit my limit for the day already on my PC and I can't whip out my phone while I am here.
OP, I am following this thread cause I have a spare Vibe that is doing somethings similar and not being recognized by my PC. I have actually read your OP more than a few times and tried all that you have, even sent it away to a developer friend of mine. He hasn't been able to get it to recognize yet either. Xenoism is in the same boat too. Keep trying and if you get Odin to see it, please come back here and post how. We'll do the same.
Here is another thread about it (Help please! Unique problem!!!)
samsgun357 said:
First thing I have to ask is do you have a stock front facing camera?
sent from my magic box to yours
Click to expand...
Click to collapse
No, it is a T-Mobile Vibrant, and thus has only one camera facing the back. However, I fail to see how it could be relevant...
Woodrube said:
^^^You learn fast my friend. I'll hit you up a bunch of thanks later on when I get off work. I've hit my limit for the day already on my PC and I can't whip out my phone while I am here.
OP, I am following this thread cause I have a spare Vibe that is doing somethings similar and not being recognized by my PC. I have actually read your OP more than a few times and tried all that you have, even sent it away to a developer friend of mine. He hasn't been able to get it to recognize yet either. Xenoism is in the same boat too. Keep trying and if you get Odin to see it, please come back here and post how. We'll do the same.
Here is another thread about it (Help please! Unique problem!!!)
Click to expand...
Click to collapse
Ok, thanks for that. Today, Ill go buy myself a new phone (probably SIII) since I don't seem to have much other choices. I'll still try to get this one to work and keep you posted if I get any results.
I'll start out that I'm new to android, been an avid blackberry user that just purchased my note 2. I followed the casual root application, and unlocked and rooted my device. I went to install cm 10.2 mod on my device after wiping the device in development mode then proceeded to install from sdcard and it failed. Now my device will not respond to either download mode or development mode or power on in any way (including using a charger and removing and replacing the battery). I'm kind of stuck and not sure how to approach the correct solution to get my device back up and running. I did make sure that the cm mod I downloaded was for my specific device. Is it possible that maybe the root/unlock method failed and thats where I went wrong when installing the cm mod? I also get no response when the device is plugged into my pc. So its not being read by odin currrently.
Since it appears I have hard bricked my device, not quite sure what steps I can do to recover. I get no power to the device in any situation, I've read online about jtag, if anyone could point me in a direction it would be helpful. Thanks in advance.
Sorry forgot to mention this was a verizon branded note 2
achiquitachaser said:
I'll start out that I'm new to android, been an avid blackberry user that just purchased my note 2. I followed the casual root application, and unlocked and rooted my device. I went to install cm 10.2 mod on my device after wiping the device in development mode then proceeded to install from sdcard and it failed. Now my device will not respond to either download mode or development mode or power on in any way (including using a charger and removing and replacing the battery). I'm kind of stuck and not sure how to approach the correct solution to get my device back up and running. I did make sure that the cm mod I downloaded was for my specific device. Is it possible that maybe the root/unlock method failed and thats where I went wrong when installing the cm mod? I also get no response when the device is plugged into my pc. So its not being read by odin currrently.
Since it appears I have hard bricked my device, not quite sure what steps I can do to recover. I get no power to the device in any situation, I've read online about jtag, if anyone could point me in a direction it would be helpful. Thanks in advance.
Click to expand...
Click to collapse
I guess no one has an idea of where to go with this now?
achiquitachaser said:
I guess no one has an idea of where to go with this now?
Click to expand...
Click to collapse
connecting to pc does your note responds or pc shoes something
remove your battery connect to pc and go to download mode by pressing the button combo if odin shows a port
and you are connected then you are saved if not I guess its tym for service center
anyways try
P.S be sure that you have latest drivers installed on pc and use the original usb cable for conecting
sangalaxy said:
connecting to pc does your note responds or pc shoes something
remove your battery connect to pc and go to download mode by pressing the button combo if odin shows a port
and you are connected then you are saved if not I guess its tym for service center
anyways try
P.S be sure that you have latest drivers installed on pc and use the original usb cable for conecting
Click to expand...
Click to collapse
Thanks for the reply sangalaxy, like I mentioned the phone does not respond at all for download mode, not recognized by Odin or showing any power when connected to a charger. Hence why I was thinking its hard bricked.
I'm not sure if I can send it to samsung, since I bought the phone off craigslist.
achiquitachaser said:
Thanks for the reply sangalaxy, like I mentioned the phone does not respond at all for download mode, not recognized by Odin or showing any power when connected to a charger. Hence why I was thinking its hard bricked.
I'm not sure if I can send it to samsung, since I bought the phone off craigslist.
Click to expand...
Click to collapse
yea sometimes it will not recognize anything and will not show on screen but will work silently
did you tried connecting it to pc without battery as I said and go to download mode by pressing buttons may be odin will recognize
if not you don't have any choice but go to samsung
Your right I didn't fully read your post to try those instructions, unfortunately it didn't work but thank you for the help. It is definitely appreciated. I think I have found someone off eBay with a good reputation for jtagging android devices that might be a solution.
achiquitachaser said:
Your right I didn't fully read your post to try those instructions, unfortunately it didn't work but thank you for the help. It is definitely appreciated. I think I have found someone off eBay with a good reputation for jtagging android devices that might be a solution.
Click to expand...
Click to collapse
ok friend hope it gets fixed
The phone notified me there is a system update so I went ahead. Unfortunately, towards the end, it gave me an error message. I remember seeing the big Android robot lying flat on its back.
Now, the phone is completely dead. When I connect it to my computer I can hear the "new hardware connected" sound then immediately the disconnecting sound. This goes on and on for ever.
I tried using the tools provided on Leagoo's site, but they're useless as the computer is not able to recognize the phone.
Is there a hard reset key combination?
Thanks.
Eddie
silentmonolith said:
The phone notified me there is a system update so I went ahead. Unfortunately, towards the end, it gave me an error message. I remember seeing the big Android robot lying flat on its back.
Now, the phone is completely dead. When I connect it to my computer I can hear the "new hardware connected" sound then immediately the disconnecting sound. This goes on and on for ever.
I tried using the tools provided on Leagoo's site, but they're useless as the computer is not able to recognize the phone.
Is there a hard reset key combination?
Thanks.
Eddie
Click to expand...
Click to collapse
I've here 4 brick-phone (friends have updated with the same result!).
leagoo support didn't answer to my polite email of support.
Anyone can give us a sugestion to recover it!?
j045 said:
I've here 4 brick-phone (friends have updated with the same result!).
leagoo support didn't answer to my polite email of support.
Anyone can give us a sugestion to recover it!?
Click to expand...
Click to collapse
In the end, I was able to finally recover it. I just kept trying and trying: while the phone was connected to the computer, I removed the battery, then I put it back in; as well I was disconnecting it from the computer, then plug it back - I did this several times until the software on the computer was able to recognize it.
Even so, when I managed to reflash it, around 60%-70%, I got a message that it failed; so I tried again - it failed around 80% then I tried one more time and it was successful. Now the phone is working fine.
So my advice to you is to keep trying - leave the software on and click on the "download firmware" or whatever it was called, meanwhile keep unplugging the phone (and play with the battery as well).
Good luck! (you will need it)
Same problem, but leagoo responded with driver, firmware, flash tool, instructions and a video.
But nothing changed, so i have to retry.
Thanks for your post.
Edit:
I was thinking that was a hardware problem with micro usb connector!
ItalianWolf said:
Same problem, but leagoo responded with driver, firmware, flash tool, instructions and a video.
But nothing changed, so i have to retry.
Thanks for your post.
Edit:
I was thinking that was a hardware problem with micro usb connector!
Click to expand...
Click to collapse
i did it! just tried a lot of times, but firmware from leagoo doesn't work, display shows only "stipes".
I found another firmware (don't remember where) and then all things went good.
Now the phone notified me there is a system update, i have to do it?
I followed the instructions provided at the MEGA UNBRICK something thread situated here http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108/
Anyway, when I hold the volume-up button for 10 seconds, followed by plugging the Onyx with the PC, the system does't detect the device. What can I do now? And is there any alternative method to unbrick a hardbricked phone? I urgently need help
If you installed the drivers and the computer is not reckognizing the device, that's bad news. How did you manage to accomplish that?
aredpanda said:
If you installed the drivers and the computer is nota reckognizing the device, that's bad news. How did you manage to accomplish that?
Click to expand...
Click to collapse
I don't know. And ijust in case if you were being sarcastic, I used the same computer to replace the recovery of this phone.
Im not being sarcastic. The problem with the Android modding scene is that people got too used to blindly following steps without really knowing how they are affecting their devices. In order to get better chances at getting help, you'll need to describe what and exactly how you were altering your phone.
aredpanda said:
Im not being sarcastic. The problem with the Android modding scene is that people got too used to blindly following steps without really knowing how they are affecting their devices. In order to get better chances at getting help, you'll need to describe what and exactly how you were altering your phone.
Click to expand...
Click to collapse
I was using Bliss ROM with BluSpark kernel. Anyway, I downloaded 2 ROMS today, Sailfish OS and the stock H2OS for OPX. I wiped the phone and first flashed the Sailfish OS, but the phone was stuck in a bootloop which only was showing the oneplus logo and the text "Powered by Anrdoid". After that, I entered recovery, and did the normal pre-flash wipe again. This time I flashed the H2OS, but after I gave "Reboot to System", my phone just wont do nor display anything. Hardbricked, dead
Can you boot it into recovery? Your bat may be dead from extensively flashing stuff, so plug the phone to the power cable and press and hold VolDown+Power for some good 30s, then you can conclude your phone wont boot into recovery and maybe need an unbrick.
aredpanda said:
Can you boot it into recovery? Your bat may be dead from extensively flashing stuff, so plug the phone to the power cable and press and hold VolDown+Power for some good 30s, then you can conclude your phone wont boot into recovery and maybe need an unbrick.
Click to expand...
Click to collapse
Yeah, it didn't boot into recovery
Does the led light up when you plug the phone to the wall? If it does let it charge for an hour before attempting anything else.
After that and before trying anything else, make sure driver signature check is off and test mode is on. This varies slightly for Windows 7/8 vs 8.1/10. Which version are you running?
aredpanda said:
Does the led light up when you plug the phone to the wall? If it does let it charge for an hour before attempting anything else.
After that and before trying anything else, make sure driver signature check is off and test mode is on. This varies slightly for Windows 7/8 vs 8.1/10. Which version are you running?
Click to expand...
Click to collapse
No, it doesn't
aredpanda said:
Does the led light up when you plug the phone to the wall? If it does let it charge for an hour before attempting anything else.
After that and before trying anything else, make sure driver signature check is off and test mode is on. This varies slightly for Windows 7/8 vs 8.1/10. Which version are you running?
Click to expand...
Click to collapse
I turned off the signature check, W8
If your led doesnt light when your phone is plugged to the wall, this is behind the hard unbricking procedure and your phone is indeed, dead.
Sent from my ONE E1003 using Tapatalk
This issue has been resolved via PM,
Can a mod please close this thread?
No idea what it could be besides corrupt firmware which I've never heard of happening before. The Qualcomm utility should work just fine. Leave it plugged in for an hour or two and see if anything happens
Did you install the qualcomm drivers? If not do it again carefully with driver enforcement off. It works like a charm. Have bricked my device twice as of now and it worked.
Hi.
Yesterday I've recived my ordered Vontar. I was not a fan of the system so i changed it via sd card. I've done it a couple of times with different ones but it something strange happened. Now, when i turn on this device with a 'reset' button and a sd card in it, it won't show 'updating' screen. In fact, I can't even go to 'apply update from ext' - the 7z file won't show under this option. But, I can install TWRP from Slimbox therad and wipe all. Also i tried to 'install' img file via TWRP but in the end it show 'System not installed'. I checked all the comments in this section but i found no answers. I think that's the only place for me to receive help because i was searching the web for 5 hours and now i'm out of ideas. I'm using custom roms on my phone since 2015 but this tv boxes are new to me.
Please help me.
Thanks in advance.
andreyGM said:
Hi.
Yesterday I've recived my ordered Vontar. I was not a fan of the system so i changed it via sd card. I've done it a couple of times with different ones but it something strange happened. Now, when i turn on this device with a 'reset' button and a sd card in it, it won't show 'updating' screen. In fact, I can't even go to 'apply update from ext' - the 7z file won't show under this option. But, I can install TWRP from Slimbox therad and wipe all. Also i tried to 'install' img file via TWRP but in the end it show 'System not installed'. I checked all the comments in this section but i found no answers. I think that's the only place for me to receive help because i was searching the web for 5 hours and now i'm out of ideas. I'm using custom roms on my phone since 2015 but this tv boxes are new to me.
Please help me.
Thanks in advance.
Click to expand...
Click to collapse
This usually indicate that either the bootloader is not compatible, The DTB dosnt have the right gpio pins assigned to the reset button making it non functional among other reasons, i Strongly advise against using an SD card to try new firmwares as you can end up in a situation like this where your box is semi broken with no way to get out of it, you should buy/obtain a USB A Male to USB A Male Cable & Use USB Burning Tool As This Is How to Recover From a Bad Flash & Not 100% Compatible Firmwares and even recover a "Bricked Box" that looks like it wont even power on (no LED or output to TV), Been Using This Method For Years And Havent Bricked A Box Beyond Repair Yet
aidanmacgregor said:
This usually indicate that either the bootloader is not compatible, The DTB dosnt have the right gpio pins assigned to the reset button making it non functional among other reasons, i Strongly advise against using an SD card to try new firmwares as you can end up in a situation like this where your box is semi broken with no way to get out of it, you should buy/obtain a USB A Male to USB A Male Cable & Use USB Burning Tool As This Is How to Recover From a Bad Flash & Not 100% Compatible Firmwares and even recover a "Bricked Box" that looks like it wont even power on (no LED or output to TV), Been Using This Method For Years And Havent Bricked A Box Beyond Repair Yet
Click to expand...
Click to collapse
Thanks for an advice. Yesterday i was very scared because of this situation. I thought that i wasted about 50$ but now i'm more chilled. Somewhere i've read that Vontar is basically the same as for example as HK1 but installing it's OS was not a great idea (I've done similar things on my Huawei G620s with the similar phone OS). I will try the USB method and reply the result. My ordered cable will be in a few days. Again, thanks for a reply. This thread could be useful if someone will have the same problem like me.
andreyGM said:
Thanks for an advice. Yesterday i was very scared because of this situation. I thought that i wasted about 50$ but now i'm more chilled. Somewhere i've read that Vontar is basically the same as for example as HK1 but installing it's OS was not a great idea (I've done similar things on my Huawei G620s with the similar phone OS). I will try the USB method and reply the result. My ordered cable will be in a few days. Again, thanks for a reply. This thread could be useful if someone will have the same problem like me.
Click to expand...
Click to collapse
Good Luck & Let Us Know How You Get On
aidanmacgregor said:
Good Luck & Let Us Know How You Get On
Click to expand...
Click to collapse
Like You said. Two minutes and Vontar is running a new OS without any problems. My SD card will come back to my car as a navigation. Thank You.