Related
Hello,
unfortunately my stylus cap came off.
Now the longer part of the stylus is stuck in the XDA :-(
Any ideas how to get it out again?
many thanks
golf
if you cant put the upper part into the xda and screw it a bit on and then pull it out
then maybe a longer metal or what ever stick with the same size thread
would be able to get screwed into the pen and then you can pull it out
Thanks for the very quick reply.
When it happened for the first time I was able to "reconnect" screwing the top part on.
But now it's not deep enough. I just doesnt connect, because the main part slid in to far or the thread doesn't grip :-(
I called O2 and they said I would have to send it in...
Very anoying...
well a long screw with the same size and the top would be able to connect would it not ?
You need to get something with the same thread as the top half but longer, then just screw it in and pull the lower half out, if it is broken off then thats a different story.
Thanks folks.
I will stop by at a DIY shop and see if I can find a long screw somewhere...
cheers
golf
I had this happen to me. I put some Krazy Glue in the top half and then pushed it onto the bottom half - waited about 20 sec, then it pulled out without a problem. My issue was the both screw threads became completely stripped.
Jon.
I used the handle end of a small artist's paint brush.
The tapered, plastic shaft was just the right size to push into the stuck portion of the stylus.
Obviously you'll need to hunt around for the right size, but most households will have something similar.
Thank you, the screw did it
I am happy to inform you that with your help yesterday I managed to release the stylus.
A long screw did the the trick for me easily.
Now the only problem left is the unstable screen color, but that's something I have to live with...
thanks again
golf
I had seen a couple threads with custom colored trackballs etc...
Look flat out i'll be honest i'm not tryin' to do anything special I got royally hammered with my brother and woke up 30 miles from home the next day missing a shoe, my back cover, and my trackball will not go left anymore...
Cleaned it quite a bit even a mild bit of wd40 on a rag hoping to break up anything abrasive which has semi-worked but now seeing various custom trackballs i'm curious...
Would anyone be able to point me in a direction for how to replace it? I'll find the ball itself unless you wanna link that too ... but is it nothing more than a ball just like an old mouse? I know people have tried to replace blackberry trackballs and never really gotten them to stay back in there so I thought i'd ask ...
thanks !
you need to fully disassemble the phone to get to the trackball assembly. Use the HTC manual that can be found by searching it, it is a step by step process with all the screws pictured so you can get it back together. It is a tricky procedure, make sure you are up for a challenge if you have never had a phone like this apart before. this is one of the harder phones to work on.
BTW, Blackberry trackballs come out the front, by removing the trim ring. No such easy process on the G1!
They have youtube videos as well!
Threads dead bud... appreciate your excitement to help
lol... did you end up getting a new track ball ?
Changed mine just for the color ...LED didnt work. Doh
I dont know why it is with these newer model phones, but just from the suggestion posts that came up when i entered the title of this thread, but My LGOT and i guess even the G2 have an issue where dusts starts to build up under the sceen....
Ive only had my phone for a little over 2 weeks, but even after the first couple days, i noticed that there were already a few trickles of dirt right around the middle of my screen.
I guess my main question is, is there anything i can do about this, has anyone had the same troubles, and what can we do to prevent this from happening?
In Thailand this is general problem of LG Optimus One
you should contact LG Customer support
they'll open your phone and blow dust out
if dust cause touchscreen malfunction they'll change new one for you
some people guess that dust already in the phone due to assembly process from factory
some guess maybe dust go through usb port
I have my phone since 2 days and i already have a dust spot in the lower right corner. This is annoying! If this spot is growing i will contact the costumer support.
Sent from my LG-P500 using XDA App
I am working on dusty area, but no dust under screen. Phone is 1 month old.
Me I have not this problem, but remains me the same issue with the iPhone 2/3 (google iphone dust screen).
I think it's a common problem with capacitive screen, but no "easy" solutions to fix it...
poor construction quality, imho.
chtamina said:
poor construction quality, imho.
Click to expand...
Click to collapse
this is one of those instances where a really cheap phone shows its faults. the phone is free on contract and little of $200 without. with it being so incredibly cheap, there is going to be something wrong that causes concern.
Im okay with it happening as long as it gets fixed and the problem is acknowledged by both LG and the phone carriers. it seems like many people are having this problem at the moment and T-Mobile is willing to exchange it in store, so good on them for being considerate.
i have the same issue. Don't know how to prevent that
ooyyeh said:
I have my phone since 2 days and i already have a dust spot in the lower right corner. This is annoying! If this spot is growing i will contact the costumer support.
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
Same Here! Very annoying because the phone is less than one week old!
I actually have not this problem my device is now over 2 weeks old. Maybe it depends on the area you are or temp.? ect...
Sent from my LG-P500
No dust here either. I have a silicon case, I don't think it helps very much.
just disassemble it. There is no warranty seal. You'll find the dust inbetween the lcd screen and the capacitive overlay.
Sent from my LG-P500 using XDA App
stefanblag said:
just disassemble it. There is no warranty seal. You'll find the dust inbetween the lcd screen and the capacitive overlay.
Sent from my LG-P500 using XDA App
Click to expand...
Click to collapse
Can you show us a Video on how to do that?
I had problem with my device, called my operator and they exchanged my phone. New phone seems alright
Sent from my LG-P500 using XDA App
just disassemble it. There is no warranty seal. You'll find the dust inbetween the lcd screen and the capacitive overlay.
Sent from my LG-P500 using XDA App
Hi! please tell us how to do it!
I too have this problem Can any one please let us know how to get rid of it.
I have the same problem with my Optimus One, dust is starting to gather on the right bottom corner and it seems to have increased since the first time I saw it. I've thought about buying a can of compressed air and trying to blow it near the edge of the screen but maybe that will just make it spread even further.
I've also thought about unscrewing the screws on the back panel of the phone and clean it but I'm afraid that it will affect the capacitive screen in some way making it less responsive and that after I assemble it back together it'll become even less air tight and thus accumulate even more dust.
Maybe I'll reclaim my warranty but I'll have to un-root my phone and wipe it clean before leaving it at the store and it's going to be a pain in the ass to reinstall everything when it returns.
Will they replace the mobile for this problem?
You can back up everything by titanium backup and copy the titanium backup folder from sd to your pc or pen drive. In your newly replaced phone you can copy back this folder to sd card and after installing titanium backup application you can restore everything.
S3nd41 said:
I have the same problem with my Optimus One, dust is starting to gather on the right bottom corner and it seems to have increased since the first time I saw it. I've thought about buying a can of compressed air and trying to blow it near the edge of the screen but maybe that will just make it spread even further.
I've also thought about unscrewing the screws on the back panel of the phone and clean it but I'm afraid that it will affect the capacitive screen in some way making it less responsive and that after I assemble it back together it'll become even less air tight and thus accumulate even more dust.
Maybe I'll reclaim my warranty but I'll have to un-root my phone and wipe it clean before leaving it at the store and it's going to be a pain in the ass to reinstall everything when it returns.
Click to expand...
Click to collapse
Sent from my GT-I5700 using Tapatalk
Wow, DUST really get into the phone and I thought I was the only person experiencing this... actually it's on the "RIGHT BOTTOM PART" as posted S3nd41 and probably half of the users here has this problem....
Anyone have problems opening the back cover like me? My fingernails hurt, A LOT, and i seem to not know the right way to open it.. Anyone have tips?
Might seem silly, but its serious, at least for me.
Sent from my LG-P500 using XDA App
I had a bit of trouble with this one at the start too... You will have to force it a bit but the trick is to push with your thumb (follow the sticker guide on the back of your phone on where to position your thumb). Pulling with your index finger will only hurt you.
I didnt take that sticker off until after a month of use ^_^ Left a different shade of black underneath...
Hello XDA Community!
I seem to be having a serious issue with my phone and cannot seem to find a solution online, so I am hoping that someone here will be knowledgable enough to assist me!
When I slide my keyboard out on my sk17i, my screen refuses to change orientation or respond to my touches. Having tested this further, it seems that it is the screen itself that will not change, but keys pressed and touches are registered. I have figured out that I can slide the keyboard out about 40% (just over the bottom row of letters) and the screen seems to change orientation to landscape AND responds visually to my touches. Any more than that and it just stops.
I looked online and someone suggested passing a magnet (fridge) over the keyboard. I did that and it worked once for about a minute. After that it returned to this state and there doesn't seem to be anything I can do about it. I have just put in an order for new facias and a new hardware keyboard to repair it as I have had it since the day it was released and some components are getting on a bit.
Does anyone know what the issue is? I only can think of one thing and that is a flex cable issue, but I cannot be sure at all...
I'd appreciate any help that can be given!
At first glance, yes, seems like a flex cable/ribbon issue. You screen will remain frozen when the keyb is completely open because the framebuffer stops receiving signal from the motherboard. It wont take long until your screen shows artifacts or goes completely blank even when the keyb is closed. Your touch digitizer might also be affected by a bad flex cable.
I suggest you replace it as soon as possible, but don't try to do it yourself unless you have experience repairing phones. I tried to do mine and ruined the LCD display, making my repair cost three times as much
PD: magnet over the keyb? never heard of that.
Pixelado said:
At first glance, yes, seems like a flex cable/ribbon issue. You screen will remain frozen when the keyb is completely open because the framebuffer stops receiving signal from the motherboard. It wont take long until your screen shows artifacts or goes completely blank even when the keyb is closed. Your touch digitizer might also be affected by a bad flex cable.
I suggest you replace it as soon as possible, but don't try to do it yourself unless you have experience repairing phones. I tried to do mine and ruined the LCD display, making my repair cost three times as much
PD: magnet over the keyb? never heard of that.
Click to expand...
Click to collapse
Many thanks for that! The flex cable is out of stock right now, so that is quite worrying, I hope it lasts the next month or so! I think I should be okay with repairing it, since I've worked with very small and delicate electronics before in Engineering. Just will have to be super extra careful! Any advice about what to watch out for?
And yup, magnet seemed to work once, I saw it on a very old thread, but that was the only advice given there.
Well, good luck! Be extremely careful with the display though, the original display assembly has unprotected corners and borders on the LCD so it's very easy to break it, especially on the lower side near the softkeys. Replacement parts often come with plastic and/or metallic protectors on them, which help keeping the LCD safe. Guess SE never meant for people to crack the phone open hehe.
again, good luck with that.
Pixelado said:
Well, good luck! Be extremely careful with the display though, the original display assembly has unprotected corners and borders on the LCD so it's very easy to break it, especially on the lower side near the softkeys. Replacement parts often come with plastic and/or metallic protectors on them, which help keeping the LCD safe. Guess SE never meant for people to crack the phone open hehe.
again, good luck with that.
Click to expand...
Click to collapse
Aah okay! I guess I shouldn't bother replacing the facia then, don't want to break the screen! Thank you once again!
Well, all my parts have now arrived, so tonight I'll be attempting this! Hopefully this goes well and fixes the problem!
ECGadget said:
Well, all my parts have now arrived, so tonight I'll be attempting this! Hopefully this goes well and fixes the problem!
Click to expand...
Click to collapse
Best of luck to you, mate.
Replacing a flex ribbon/cable on the mini pro is no easy task, requires patience and steady hands when sticking the big square part onto the metallic slider while making sure all of the other components (home button, camera, led and sensors) keep aligned in place. Do it wrong and you're in for an even more tedious mission haha.
PD: here's a crappy pic from when I did mine
Pixelado said:
Best of luck to you, mate.
Replacing a flex ribbon/cable on the mini pro is no easy task, requires patience and steady hands when sticking the big square part onto the metallic slider while making sure all of the other components (home button, camera, led and sensors) keep aligned in place. Do it wrong and you're in for an even more tedious mission haha.
PD: here's a crappy pic from when I did mine
Click to expand...
Click to collapse
Thanks for that! I was just struggling to take the motherboard off, and looking at the picture helped me see where I could try to pry it open!
Yeah, the mobo can be a b*tch to take off. Glad I could help. Be sure to tell us how it goes.
Pixelado said:
Yeah, the mobo can be a b*tch to take off. Glad I could help. Be sure to tell us how it goes.
Click to expand...
Click to collapse
Well, after a cracked front facia (thanks to the previous repair that I had on it two years ago), and my temperamental lights, my phone works a charm! Replaced the flex cable, motherboard mount and hardware keyboard. Once again, thank you so much for your advice, I have decided to hang around this place much more often!
Repaired two years ago? Wow, your phone is kind of a veteran haha, mine is about to turn 2yo in about two months. Gotta get a birthday cake.
Good to know everything went fine. See you.
Pixelado said:
Repaired two years ago? Wow, your phone is kind of a veteran haha, mine is about to turn 2yo in about two months. Gotta get a birthday cake.
Good to know everything went fine. See you.
Click to expand...
Click to collapse
I've had my phone since two weeks before it was released in 2011 xD
I'm sure your phone will love the cake
Noticed a new glitch with my phone though... the softkey and keyboard lights start to light up when I switch the screen on, but as soon as the screen switches on the lights switch off?
Never heard of such problems. What rom are you on?
I am running a stock gingerbread 2.3.3 rom, just rooted it a year ago. No other changes, apart from shoving CWM onto it for backup/restore
Hey guys, I just saw this post after hours of frustration!, I recently changed my damaged slider mechanism on my sk17i and I had to transfer the ribbon cable from the one mechanism to the other but I glued it with 2mm adhensive that is used for screen, and the problem is when I open the phone it is always on landscape mode, like the phone thinks the keyboard is always out! Before I tried this repair
everything worked perfect
How the phone understands if the keyboard is out or not?
Please tell me what I could have done wrong, I would appreciate your help here!
Sorry for my bad english
Thank you in advance!!!
I've been trying to figure that out myself too, it seems to be some kind of optical sensor. Whatever it is, it just works for me hehe.
Pixelado said:
I've been trying to figure that out myself too, it seems to be some kind of optical sensor. Whatever it is, it just works for me hehe.
Click to expand...
Click to collapse
And you dissasembled it and re-assembled with no problems?
r3izor said:
And you dissasembled it and re-assembled with no problems?
Click to expand...
Click to collapse
Welcome to XDA.
Like Pixelado said, it is probably an optical sensor. My advice would be to disassemble the phone again (without unsticking the flex cable though) and make sure everything is back in its correct place. It make just be something is a little out of place, which is very easy to do! Good luck!
r3izor said:
And you dissasembled it and re-assembled with no problems?
Click to expand...
Click to collapse
Yes sir. I have never re-used a flex ribbon though. I removed the broken factory ribbon and stuck a new one in. No problems.
Pixelado said:
Yes sir. I have never re-used a flex ribbon though. I removed the broken factory ribbon and stuck a new one in. No problems.
Click to expand...
Click to collapse
Then as long as I dont know where the sensor is in order to find out my mistake, I am afraid my phone will be permanently on landscape :crying:
Thank you for your replies guys!