UPDATE: This tool has been superseded by a newer version. This new tool does not work for Radio version 1.05.12 (see below). The new tool works for 1.05.12A and later. For more information on the new tool see the new thread
==============================================
This is old information. Only use this method for 1.05.12
Despite some set-backs and not precisely the easy tool we want (yet), we didn't want to hold this back.
We are proud to present the new unlock tool for the XDA II!
One of the prerequisites for using this tool is puting the XDA II in bootloader mode.
Unfortunately this will also mean a hard reset of the device: you will loose all current data!
So the advice is: MAKE A BACK-UP FIRST! (And test that it works).
Puting the device in bootloader mode requires pressing three buttons at once:
The Power button, the Action button (also called Navigation pad)
and the Reset button in a hole at the bottom with the stylus.
When you run this tool on your PC, it will run in a DOS box and extract the unlock code from the device.
It will probably not work on Windows 98, but it does on Windows 2000 and XP.
This tool was tested with Radio version 1.06.x. It might not work on Radio version 1.10.x!
It won't unlock the device for you. You can do it through the standard interface.
When you run it, it looks like this:
Code:
XDA Developers XDA2UNLOCK tool
This program will extract the unlock code from your XDA II.
For this to be possible, a few steps are necessary:
1. The XDA II needs to be put in bootloader mode.
NOTE: THIS WILL WIPE ALL YOUR DATA SO FIRST BACK-UP!
You enter the bootloader by holding the Power button and the Action button
while pressing the stylus in the reset hole on the bottom.
In the bootloader mode, the display will be gray and say Serial at the top.
2. Next put the device in the USB cradle. The display will now say USB
and the first time Windows will detect a new device.
3. Disable USB in Active Sync in 'File -> Connection Settings'
Now the device is ready to extract the unlock code.
Type YES when you have completed the above steps and want to continue: YES
Communication port opened.
waiting for radio bootloader
reading first block...
reading second block...
Unlock code: 2040248
When you insert a blocked SIM in your XDA2,
you can enter the above code in the SIMLock box.
Alternatively, you can connect to the wireless modem
and enter the following AT command:
AT%HTCLOCK=0,2040248,1
Do not forget to enable USB in Active Sync again!
For download, go to http://wiki.xda-developers.com/wiki/xda2unlock
Please write comments, questions, supporting explanations etc in this thread.
:lol: WOW
The bar is stocked up with a few extra barrels of beer for the celebration.
he's the best!
You are really the beast one!
have a bear and many thanks for your greater job.
Last thing would be to making writeable the extended rom, as the last 10 MDAII i had, they're not writeable anymore.
Thanks and ciao.
working on that one. seems to be protected rather good. I suspect that unprotecting it will involve reformatting the partitions. and then reloading them with data.
have a bear and many thanks
Dave
Help ! please , I got a problem , everything runs ok until :"reading second block"... the DOS box disapear !!! no code ....what can I do ????
On the XDA II , I can read on the screen : "xda2unlock"
What can I do , please ? Thanks a lot !
tenzin said:
Help ! please , I got a problem , everything runs ok until :"reading second block"... the DOS box disapear !!! no code ....what can I do ????
Click to expand...
Click to collapse
Woops, my mistake. I added an extra "Press enter" line so it pauses.
You can download the new version from the usual place:
http://xda-developers.com/xda2/xda2unlock.exe
.... i'm new here but i think it's a very good community..
tnx a lot for your brain sharing...
pLu
source available
As a good tradition we also made the source code available at:
http://xda-developers.com/xda2/xda2unlock.zip
WONDERFULL !!! Thanks, thanks, thanks : my xda2 is free !!!
I love you !! :wink: :mrgreen: It's a fantastic Christmas present !...... you're the best ...Cheers !
It worked!
Since O2 charge £15 to do that (and there's no guarentee that they'll do it)... I'm donating it to you!
Thanks a lot guys!
Congrats. You are a great blessing to the tech community. Though I'm in Nigeria and I doubt if I will get an XDAII soon, but now I know whenever it comes unlocking will not be a problem.
God bless and preserve you.
Great: it even works! :wink:
Thanks for giving us Freedom of Provider
I've tested it too
It works fine on my O2 locked XDA2. Brilliant. I take back all I said.
thanks works like a dream!!!
THANK YOU
Mogelijkheid gebruik van MDA i.c.m. andere providers
Heb het unlock-programmaatje even uitgerpobeerd en werkt ook voor de MDA2! Ben dus erggg blij;-)
We hebben de MDA2 op voorraad en kan door ons gratis worden aangeboden i.c.m. een (zakelijk) T-Mobile Optimaal-abonnement!
Dus heb je interesse, just let me know;-)
Grtz,
Sander
Thanks, It ended up being very easy.
Thanks!
:lol:
Excellent guys. Worked like a dream! Many, many thanks.
A Message to SANTA!
WELL You have DONE IT Again!
THANK YOU!
May all your dreams come true!
Mine did! :wink:
Related
Have I fried my XDA 2?
I've had this thing 1 hour and I was running the latest rom upgrade from O2. While it was checking the rom in my XDA2 it came back saying "Error 120: Country ID Error". Now the thing is stuck in a serial bootloader 1.03 mode and grey screen.
I'd not made ANY changes to config of the XDA before trying to upgrade it.
Any ideas?
Don't lose hope mate! I had a very similar problem, with the same result, only my screen said "Serial v1.01" Black text on grey background, no backlight. When I placed it into the USB Cradle it changed to "USB v1.01". It would do this even after I took the battery out for 20 minutes, the moment I relaced the battery, without even pressing the power button. I believe this is correct operation for the XDA II when it's "between ROMs" so to speak, perhaps someone in authority will confirm this?
Anyway, after rebooting the XDA II and the PC, and re running the upgrade sequence about 10 times it worked, and I now have a perfectly functional XDA II. Made me sweat, and swear, for a few hours though, I can tell you.
Keep trying and good luck. Sorry I can't help more!
Andy
I have the same problem... still not working eventhough tried many many times..
It wont even go to bootloader mode.. (pressing power, navigation and reset button)
I come up with serial on top but when i plug-in to a usb cradle it turns to USB and v.1 06 at bottom..
I also tried with different roms.. (QTEK and MDAII) upgrade utility but it only comes up with a window "checking the information on your pocket pc.. .please wait" then the xdaII screen went blank (like no power) and the utility does nothing else..
can someone help? or have i lost the xda II totally?
Hi,
Same problem for me!
Please let me know how it can be solved.
:evil:
I am in the same deep **** ma self! please any1 who knows please help us!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Sent back to the place where you buy your XDA... :? that's the only way...
Sent back to the place where you buy your XDA... that's the only way...
Click to expand...
Click to collapse
ITS NOT THE ONLY WAY.. because what we did is actually out of warranty.. we are trying to be different with others.. besides if you can't put a good answer you better not reply at all.
alimx said:
Sent back to the place where you buy your XDA... that's the only way...
Click to expand...
Click to collapse
besides if you can't put a good answer you better not reply at all.
Click to expand...
Click to collapse
alimx, You could be more polite replying to him, he was giving you a suggestion, why you become RUDE!!
well, If i have an answer or a solution to your problem then I prefer NOT to give it to you, jerk!!
:evil: :evil: :evil:
alimx,
when it says "Serial" and "v1.06" then changes to "USB" when you place in the cradle, IT IS in bootloader mode.
I had this same problem with a recent i-mate I bought for my boss. It won't let you downgrade or switch to any other ROM besides the 1.66 i-mate ROM.
1. Open Activsync without the unit in the cradle.
2. Go to Activsync and uncheck the box where it says "Allow USB Connection with this Computer" (seems strange I know but it works)
3. Put the i-mate in the cradle. It should say "USB" and "v1.06" at the bottom.
4. Download and run the i-mate ROM version 1.66 from clubimate website.
5. Allow it a few minutes and it should finally come up with the screen about converting blah blah to blah blah ROM.
For some reasons, the new i-mates coming out that have the 1.66 ROM will not allow a downgrade to ANY OTHER ROM. Which I think is BS.
For the guy having trouble with 1.10 Radio version. My suggestion is to re-run the 1.66 ROM (I think it's your only option at this point until a new ROM is issued from i-mate). It may fix things. My 1.10 radio version seemed better the second time I loaded the ROM (I know it shouldn't make a difference but it seemed to).[/list]
Hi
When i tried the upgrade program version 1.0 from orange 166 DK my XDAII started at least to show error codes when upgrading.
Before it only become black
My unit was á new QTEK 2020 with french system 1.66, boatloder 1.06 maybe newer units needs the latest himalya upgrade software.
I will keep trying
Dear all.
I had the very same problem couple nights ago. All I did was soft and hard reset, all of which didn't help. But just before I lost my hope, I re-cradled my XDA II, at that time my xda's screen was still black and displayed "Serial", then I chose different upgrade version and installed it from my PC and everything turned out fine.
HTH Cheers,
I am having the same trouble
I am trying all these suggestions, but with no luck so far! (my screen displays v1:01 When I try and install anything on it, my pc can't detect the device
Any more advice?
HI
I found this
http://www.sourceo2.com/O2_Developers/Devices/O2_Xda_II/XdaIIRom.htm
I downloaded the xdaII launch rom, and it is working!! My screen tells me it is upgrading!!
Hope this helps!
Have fun
pw
my appology
My appologise goes to nakamichi... and alexlloyd54... sorry, i didn't mean rude.
I have bootloader version: 1.03
When I turn on my xda i see only screen:
serial
v1.03
i think that my xda is dead how can i repair this?
I try flash my device using sd but i dont have this option in my bootloader..
You should be able to upgrade your device using the HimaUpgradeUt program. See my post here for information on what to look out for, etc.
I think thats is not good way because i cant connect my device to pc using activesync.. i have only bootloader mode on my xda..
That doesn't matter, the upgrade doesn't need Activesync. It looks after its own connections.
I just connect my xda in bootloader mode to usb. The activesync not saw may device but i run HimaUpgradeUt.exe and my device start upgrade! I have Germany ROM now i upgrade this To same English ROM.. Before i do this that way program show mi error 102.. now its look like everthing be good.. we will see for 5 minutes.
sorry for my english
i am from poland
OK. Let me know what happens.
The program just finish operation.. but on my device screen is still:
Upgrading
radio stack
Please Wait...
I dont know what i should do..?
That's OK. As long as the PC said 'Congratulations' its all done. Take your device out the cradle, hard reset it and it will run the standard setup.
Everythink is great! My Pocket Pc work! Thank You for Your advise.
Maybe somebody know where I can find some Rom to Xda.. Without O2 Rom because i have it. Maybe there is some rom kitchen like for xda 1
Excellent news For information about customising the Extended ROM, search for Extended ROM on the forums.
to dcs: I'm now upgading my o22'Rom from v2.06 to 2.20 (translated frm chinese --> english). after I completed fixing country ID, I have a new erro (erro102: CE image file checksum erro. the Rom image file to be used for the update is corrupt). I try to download again and update but I fail, the erro is 102. please show me hoe to pass this erro.
thank
If u see the log after HimaUpdIt ul see some like this;
16:27:04 Connection with USB
16:27:37 Begin stage 1
16:28:11 End stage 1
16:28:12 Begin stage 2
16:28:12 Write block1
so, he searches for his own connection! Dont worry just download the rom, himaupdit file and upgrade ur xda Tell us how it works
Can anone tell me how i could unlock my wallaby lock on T-mobile?
i have already upgraded the ROM to 4.01.12
and radio to 4.21.00
protocol version is 32S54... but get Unlock Code screen everytime i insert my simcard...
please please please, im begging.... i read one article explaining about SpecialEditionROM but the link is dead... any option pls.???
http://wiki.xda-developers.com/index.php?pagename=UnlockWiz/Wallaby
T-Mobile Unlock
Lumpi,
I, too, have T-Mobile that I need to unlock. My problem is that I can't figure out how to install the XDA ROM that allows the unlock--the link at the bottom of the XDA page doesn't work.
Skip A
http://wiki.xda-developers.com/index.php?pagename=Wallaby
I can't open the step by step instructions for installing 'special edition 1.2'.
Some Wallabys don't support the GSM network that T-Mobile uses (at least in the UK), so if your phone works with other SIMs from Vodafone/O2 then chances are it will never work with T-Mobile. In this case, it's a hardware limitation and there is nothing that can be done about it.
Dear Stefan I want to meet u in person in stuttgart
LumpiStefan said:
http://wiki.xda-developers.com/index.php?pagename=UnlockWiz/Wallaby
Click to expand...
Click to collapse
Dear Stefan i will be in stuttgart for a church conference from 3 april to 12 april.
I have t-mobile wallaby PW10B1 ROM 4.02.04 eng 8/24/05 radio 6.18.00 protocall version 324e4. I am unable to unlock using xdadev_all_unlock.exe they give errors.the other ROM version u mentioned site http://cuba.calyx.nl/~jsummers/XDA/XDA-developers-SER-v12.exe is not working. can u please help me. is it possible to add a camera and GPS reeciever to my pda? i dont have serial cable.is it possible i can wire them all?
kjpeter said:
I am unable to unlock using xdadev_all_unlock.exe they give errors.
Click to expand...
Click to collapse
This is the wron tool. That does not work on the Wallaby device.....
kjpeter said:
the other ROM version u mentioned site http://cuba.calyx.nl/~jsummers/XDA/XDA-developers-SER-v12.exe is not working.
Click to expand...
Click to collapse
I think you´re concerning on, that the link for downloading is not working...
Try this one: ftp://xda:[email protected]/Wallaby/ROM/Special/special_rom_1.2.exe.zip
kjpeter said:
can u please help me. is it possible to add a camera and GPS reeciever to my pda? i dont have serial cable.is it possible i can wire them all?
Click to expand...
Click to collapse
GPS-receiver should be no big problem. It should be a gps-receiver with PS2/serial-Connector. Any USB wouldn´t work....
How dou you want to conenct a camera?
If you didn´t get the unlocking worked, we can try if we can make a meeting when you are in Stuttgart, than i will take a look at it....
Stefan
I downloaded SE rom 1.2 and when i run exe in dos window i have a message - ERROR GetConnectionType.
i used activesync 4.5 beta on xp .
(actually i had activesync 3.5 on my xp pc but on wallaby-activesync itsays incompatible activesync .so i changed from 3.5 to 4.5 beta )
any help stephen?
how to upgrade the activesync in my pda?
you dont
upgrade it
Try using the 3.7 or the 4.0/4.1 Version of Active Sync.....
Stefan
xda2unlock
I put in boot loader mode the pressing left side sound control switch put it in to USB flash mode and ran xda2unlock.exe at desktop got XP shutting down that xda2unlock.exe. at that time i put active sync USB on stop. couldnt do any thing.
while try once i saw serial rs232 on wallaby screen i dont know how to acivate it again and try abouve procedure.
is there any other way to unlock my mobile.?
I want to connect to gprs and browse net.
wallaby unlock
i was finnally able to unlock mine yesterday (02/25/07) but you need to change 2 things before being able to use the unlocker.exe program . first you wont be able to do it via the usb connection it just wont work due to the rom currently installed use the sd mem card method to flash the rom using a card reader and OSIMagetool.you need to change the rom to the ROM: 3.17.03 ENG (XDA special edition) you need to do this so you can flash the radio and the current rom wont allow you to do it and then change the radio to version to Radio: 6.24.00 (mine was 6.25.02 and its whats not allowing the unlock to work ) then the unlocker.exe will work . the instructions are on this url http://www.romkitchen.de/tools/manual2_unlock.htm and the software i used is on this url http://www.romkitchen.de/tools/form.php .The instructions here changed the boot loader but it wasnt needed to get my phone unlocked you can probably skip that step also . good luck
Please, link is not working
The link ftp://xda:[email protected]_1.2.exe.zip is not working anymore.
Could someone please, point me in any other direction I can look for?
Thank you very much.
Manuel J.
P.S. Still searching
http://www.romkitchen.de/tools/special_rom_1.2.exe.zip
LumpiStefan said:
http://www.romkitchen.de/tools/special_rom_1.2.exe.zip
Click to expand...
Click to collapse
Thank you so much.
Manuel lJ.
want to meet u in stuttgart
Dear lumphistephen i dont know your personel mail id so this message ,i am reaching stuttgart on 2 april will be there till 15th april for church confernce how can i contact u there?
My Host Mr.Gunter Janzens phone number 0711-4579360 or 0711-457790 or 0175 689 5555 (mobile).Also u r welcome for the meetings where friends from all over the world come there for christian fellowship.can u please
give personel mail id .mine is [email protected]
Hi guys,
Hi,
I'm a hp rw6828 user and is very much enthusiast to try out those wm6 roms made by those experts. However, i did a mistake while trying to flash.
I tried flashing with a rom from wantat but i forgotten to delete the EBOOT.nb0 before i clicked "upgrade". Then the program stopped at 6% for a long time and didnt move. I disconnect the cables and tried to turn the device on.
THe device can go into the wm6 and the start button can be use but the screen is "moved" to the right side and other function is not working.
After that, i did a hard reset and the the os seem to work like normal. However, when i tried to go into bootloader mode by pressing both "_" and soft reset. That didnt work. I tried another way by taking out the batt, leave it for a 10mins, press both "_" and soft reset, put in batt, release soft reset then "_" keys. That didn't work either.
But, just lately, i've tried taking out batt, holding the camera key and softreset, place back batt, release soft reset n camera button. This method works and i get what it seems to be an atom bootloader?
i get a black background with "MN1 Bootloader Mar 29 2006 13;52;14 copyright..... 1) debug module through UART 2) jump to DM Enter your selection.
I've searched the forums and found few ways to downgrade back to wm5 but those aren't the same conditions with what im facing. Can someone recommend how can i downgrade back to wm5 with the conditions that im facing? All you help is much appreciated. THank you.
You are lucky , at lease your device now become atom. My was totally cannot on power and just vibrate. Till I have to sent it back to HP SC and change the main board . Can you understand chinese , if yes than I have a solution you may try . Else you have to wait . I just download a program and doing some testing , the program is in chinese language .
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
elus said:
Thx for you reply. I guess u can say that. I'm from msia but cant read chinese.
Is it possible to solve the problem by sending back to hp using warranty claim? I think i still have warranty left but its ending very soon. One more week i think.
Click to expand...
Click to collapse
I don't think you still can claim under warranty unless you can make your phone total can't on and access to windows mobile. Last time I sent it back they charge me RM 385 to change the main board . I did talk to their technical personal , it seen like they don't know what is bootloader and flash it back to original rom . What they do was just change the main board with preloaded program .
Good luck
If you think that you can claim you warranty , than you just go a head . If not , may be you can access my thread "HP6828 WM6" , download any one of the rom that I post , follow the instruction accept downgrade bootloader . Enter your phone in bootloader mode . If you can start the process , than it will flash a new hp bootloader into your phone .
Against . Good luck
Cheers
I'm from malaysia also.
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
elus said:
Ok. I'll try your method to restore the bootloader. Thx for the fast reply. I'll keep u update with the progress. Thx again.
Click to expand...
Click to collapse
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
nhocbanme said:
You've flash ATOM Bootloader, there are many ways to restore to HP Bootloader ... don't worry !!!
Click to expand...
Click to collapse
Can share the information how to restore back the HP original bootloader ? And the procedure . Thanks
First you must have HP bootloader file (Eboot.nb0) 1.01 or 1.05 are OK.
- Use DRUU to restore Bootloader : replace ATOM bootloader file with HP bootloader file
- Use miniSD to restore Bootloader : copy Eboot.nb0 to miniSD card, go to bootloader ... wait 1' it will auto hard reset.
After flash successfull remmember remove Eboot.nb0 from miniSD.
- Reflashing Bootloader using JTAG. (Use only when can't use two above menthods)
HP Bootloader 1.01 : http://rapidshare.com/files/82853862/HP_BL1.0.1.rar
HP Bootloader 1.05 : http://rapidshare.com/files/82853924/HP_BL1.0.5.rar
nhocbanme could you please specify which specfic DRUU should be use for your method? Thank you.
You should use DRUU of Chartreux, replace Eboot.nb0 and choose OS and Eboot
Remember copy a HP68xx ROM (diskimage_Ver.nb0) to C:\Windows\Temp with DRUU of Chartreux then start...
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
elus said:
nhocbanme, you explanation seems vague to me. Probably cause im still new. Could you please give a clearer instructions? Thank you
Click to expand...
Click to collapse
-You must extract RUU in C:\Windows\Temp (no sub folder) then replace Eboot.nb0 with Hp bootloader 1.01/1.05
-Copy a diskimage_Ver.nb0 (any ROM WM6 for HP 68xx) to C:\Windows\Temp
-Run the DRUU program and choose OS and Eboot and start.
Goodluck !!!
It worked! Thx a lot nhocbanme and wantat. The methods restore the atom bootloader to hp bootloader. The DSUU by chartreux is a good tool.
Now, i would like to put this solution up into the wiki. How may i do so? Thank you.
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
williamSun said:
hi, im william from M'sia. i like to know how you recover your previous installed AtomROm back to WM5.
can u provide some step to step detail
if possible upload some files can let me flash from memory card in the bootloader screen
ur reply are highly appreciated
thx ~~
Click to expand...
Click to collapse
OK, please read my topic, I'll post a WM5 ROM flash via miniSD
help !!
im facing another problem again...
this time i changed the file extension EBOOT0502_MNT_01.01.03.nbf to EBOOT0502_MNT_01.01.03.nb0
(file from HP official WM5 SP34074, inside the installed folder )
and copy to memory card and put in 6828 then started to go bootloader screen
few minutes later my screen goes blank, and i tried with the revive methods
which is
-press the 2 softkey " - " and reset button
-put in the battery ,
-release reset, then release softkey
but didt work out!!!!no repsponse at all..tried many times..possible dead ad???
plz help me abit ..big troblem!
I dont think i can help u much here as im still new. From the looks of your problem, i guess u forgotten to cut the first 12bits (or something like that) of your bootloader when u use it to flash via mini sd. Maybe you can try the JTAG method mentioned in the atom wiki to restore your bootloader. Good luck.
Thanks guys!
The same exact thing happened to me yesterday..I was already about to sell my ipaq as a dead unit and i came upon this thread and after following the steps it did made ipaq alive again..
thank you very much guys,i hope you continue to help more people..
god bless and best of luck to you
more power xda-dev!
HardSPL kit for NEON400 (CDMA)
=======================
Brought to you by JockyW (jockyw2001)
March 19, 2010
Download: http://forum.xda-developers.com/attachment.php?attachmentid=295986&d=1268994888
DISCLAIMER: I WILL NOT BE RESPONSIBLE IF YOU BRICK YOUR DEVICE USING THIS TOOL
THIS HARDSPL IS ONLY FOR NEON400 AND NOT FOR NIKI
Instructions
-------------
1. connect your NEON400 with your PC by USB cable and boot into Windows Mobile
2. wait until ActiveSync is ready (icon green)
3. run "flash-hardspl.bat" to flash the HardSPL. It will create a backup of your current SPL
(called "spl-backup.bin") and creates a file "check.bin" in subdirectory "1" (for diagnostic purposes)
4. the phone will be rebooted automatically
5. you can now flash any cooked or original rom, splash screen or radio rom
Notes
-------
- if your device is application locked the batch file will run with errors. To app unlock your device
Download PHM Registry Editor - v0.70 from here:
http://www.pocketpcfreeware.com/en/index.php?soft=31
Copy it to your device and execute it.
Modify this registry key:
HKLM/Security/Policies/Policies/0000101B if set to dword:2, change it to dword:1
Reset using power button and try again.
- the HardSPL is based on the SPL v0.28.0000 (Neon_C, Shipped)
- a quick verification for correct installation is to boot into SPL tri-colour bootloader screen. In the top-left corner it should display "0.28.Hard"
- to flash back the stock SPL 0.28.0000 run "flash-stock-0.28.0000.bat"
- to flash your original SPL run "flash-your-backup.bat"
Roms
------
I have reconstructed the original NEON400 Bell and Telus WM6.1 Pro Build 19965.1.2.3 roms from dumps.
You can find them here: http://www.sendspace.com/file/zkxsyc
With these roms you can easily set up a kitchen for NEON400.
Check this Kaiser kitchen tutorial for a jump start:
http://wiki.xda-developers.com/index.php?pagename=Kaiser ROM Kitchen Tutorial
Credits
--------
- itsme for his fantastic open source itsutils package
- Tadzio for his ImgfsTools
- pof and Olipro for many HardSPL patches
- cobra_21ca for testing HardSPL
- cpuguy, Roadhog ([email protected]) and edgarpoe for dumping the roms
Donate
--------
If you like the HardSPL and appreciate the time and effort I have put into this then feel free to send a PayPal donation to [email protected]
or click the donate button in my signature.
Enjoy,
JockyW
-- reserved --
Thank you JockyW I know you have done a lot of work on this from all our emails about this I will be making a donation tonite!
Thank you EVERYBODY for all your hard work!!!!!!!!!
Moderators, please sticky this! Also, would some chefs please start cooking NEON400 ROMS?
Yay!!
88fingerslukee said:
Thank you EVERYBODY for all your hard work!!!!!!!!!
Moderators, please sticky this! Also, would some chefs please start cooking NEON400 ROMS?
Yay!!
Click to expand...
Click to collapse
will try bro.but the rom will not be tested on my device.as I am having a nike only.so will need testers also
regards
Hey thankyou for making my day! I searched high and low (xda and ppcgeeks) for neon400 threads. Im all giddy that i had the privilige to be a part of the project.
I started cooking for my vogue recently after months of trying out everybody elses roms. I love it! I'm happy my father in law's bell neon needed the factory reset. (although he was pissed to loose his contacts. (i installed pimbackup for him now)
deepankerjha said:
will try bro.but the rom will not be tested on my device.as I am having a nike only.so will need testers also
regards
Click to expand...
Click to collapse
Let me know if you need someone to test, I will gladly test!
Donation
Jocky just sent you a donation for all the work you put into this, thank you!
Oh man I love you for this!
JockyW, I just tried to flash the bell rom with no success but the telus rom will load with no problem.
The bell rom gets stuck at the HTC start page immediately after the phone is turned on.
cobra_21ca said:
JockyW, I just tried to flash the bell rom with no success but the telus rom will load with no problem.
The bell rom gets stuck at the HTC start page immediately after the phone is turned on.
Click to expand...
Click to collapse
Hmm weird. Looks like the dump isn't perfect. Will check it.
jockyw2001 said:
Hmm weird. Looks like the dump isn't perfect. Will check it.
Click to expand...
Click to collapse
What did you find out?
hi,
i used your tool....and broke my device..
after the automatc reboot, my device turned off....and now it doesnt react on anything!
the power function is lost, the akku isnt charging, the device isnt starting, just black screen without any led lighting....
nice work ( the device was 2 weeks old
You installed the NEON400 hspl on your Niki I assume. The Neon hspl is *not* for Niki and will brick it. For Niki you find my hspl below ...
Connect your Niki to your PC and check if you are prompted to install drivers. If it does, your niki can very likely be unbricked using a modified version of my Frankenkaiser tool.
yes when i connect, windows starts searching driver for an device called: data interface
but doesnt find it
what tool do i need?????
Sam40918 said:
yes when i connect, windows starts searching driver for an device called: data interface
but doesnt find it
what tool do i need?????
Click to expand...
Click to collapse
i've sent you a PM
thx, i tried - but phone is not able to be seen by the software you told me
Sam40918 said:
thx, i tried - but phone is not able to be seen by the software you told me
Click to expand...
Click to collapse
Please don't use this thread, stick to PM
Hello please help me Myphone is closed,my phone not cdma phone your topic to programs install to myphone.My telephone model htc niki 100 (Turkish version) I am from Turkey , my telephone not guaranti,300 $ repair money in turkey help my telephone opened program your topic upload ?
it's written in red and in largest fontsize the neon400 is not for niki