Hi
I installed piece of Software called GPS Assist to acompany by TomTom Nav software. Big Mistake.
Did a Soft Reset, and it gets to the Today screen, displays half the items on it (sometimes less or more after every reset) and then just freezes.
Tapping the screen or any hardware buttons wont do anything. Im guessing something that runs for GPS Assist is starting on bootup, and freezing it.
I really dont want to do a Hard Reset, I've been careless lately and not backed it up in quite a while.
Is there anything I can do, some way of getting into the bootup and stopping services..or anything like that ?
Thanks
David
XDA 1
WM2003
4.00.11
R4.16.00
hmmmm
Hey, for me have the same issue. but i tried installing Transformer 1.1.... Even I tried Hard reset... not working... have u found the solution????
I am using HTC ELF...
If any one have solution plz post it...
probably you will have to hard reset it, it has been a long time since i used a wallaby, you should of installed a program called safe mode which allows you to do what it says and go into safe mode on the pocket pc, spb pocket plus has a similar function too. This would of at least allowed you to boot up the wallaby and uninstall the offending program.
have you tried just leaving it on for half an hour ,connected to the pc. it might not be actually crashing just locked in a never ending loop?
And you did hold the power button in while using the stylus to reset(A hard reset) not just used the stylus to reset(Soft reset)?
Related
I can't ound the answer with the forum search.
My Wallaby does not have a hard-reset switch. How can I hardreset it without to disassemble and take out and in the battery?
Sometimes I try functions in the bootloader menu, and after it, the Windows does not start. Only display the background with the radio and wince version number. In this case only the hardreset helps.
Any idea?
Sallala said:
How can I hardreset it without to disassemble and take out and in the battery?
Click to expand...
Click to collapse
It would be possible to write a program which causes a hard reset. But in the situations where you'd need it, you can't run the program anymore. You could try wiring in a new pushbutton if you're really (really!) good with a soldering iron, otherwise I'd refrain from playing with the bootloader on such a unit.
If you leave it in bootloader mode, this will drain the batteries really quick (causing a hard reset) since the backlight stays on and power-management happens. This would still take up to a few hours, but would save you the hassle of opening it up.
Thank you!
So there is not a special key-combinations like the new iPAQ-s.
I use it for three days. I must to hard reset two times. (After I try to changed something in the bootloader)
In the first time, I pressd various key combinations, and I could hardreset it, but I can't remember how
Ok, your tipp is a good, if I'am not at home, and do not reach my torx
Gabor
I find it hard to believe that there is no button combination for a hard reset
have you tried reading your Wallaby manual?
In any case, I have an app installed called THM Task Manager, and it has a "shutdown" option which INCLUDES hard reset. I haven't tried this yet (for obvious reasons) but you're free to so if you'd like.
Hope this helps
Carlo
you have not tried inserting the unscrewed cap of your pen into the lower right pinhole on the side of your xda?
There is no hardreset micro-switch inside.
On the mainboard there is only the place for the switch, but no switch.
I read the wiev the manual for the Qtek1010 only, that I downloaded, and not found any text about hard-reset key-combinations.
I bought it from a guy, who build a working xda from two killed devices. I gave only a sync cable, no manual or anithing else.
Hard-reset program sometimes can't help. As I wrote, I needed hard-reset two times, after I changed something in the bootloader. The device stops at the windows welcome screen, wher the version number displays. I can't start any hardreset program at this tiem.
Thank you,
Gábor
ic, so it's a sort of "refurbished, frankenstein" unit. the guy must've forgotten to put on the micro switch, when he was putting the thing together.
you could disconnect the battery and wait till the backup batt drains too. that should hard reset the thing, when you reinsert the main battery
Download PHM Task manager here:
http://www.phm.lu/Products/PocketPC/TaskMgr/
Install it.
Then go to the shutdown menu - there in is a "hard reset" option
Follow the warnings etc and execute - your device will then be hard reset!
FYI,
JB
PS: please post if this solves your Frankenstein units problem...
I thought the hard reset was a hardware feature on the xda that isolates the battery physically from the board, is that possible to implement in software??
Admittedly - I never used this method on my old XDA; however, I have used this on two Toshiba PDA's (e740 and an e755) and it works.
To the best of my knowledge, this works via software by telling the device to release/erase everything in volatile RAM - ie a hard reset w/o cycling the battery.
-JB
Hi
Unfortunately I was in the middle of upgrading the software to version 172181 when I decided, for some strange reason, to pick the phone up out of the cradle and make a call. DOH!
I can no longer get the phone to boot up / turn on it is just stuck on the low light o2 backscreen and shows
r 1.17.00
g 1337.20
d 1.72.00wwe
Im quite literally just stuck on that screen, the phone wont seem to reset, reboot or hard reset or turn on or off.
I assume im doing the hard reset correctly on/off button and reset button with stylus.
I did see somewhere to use the on/off button, camera button, record button and reset button with stylus but this does not appear to work either.
I don't know whether the condition is terminal or not but anyone can help i would really appreciate it I have a lot of information on there that is very valuable to me.
hi
had same problem D/pad on/off button and reset release reset first and it should put it back in bootloader mode then do upgrade again, it did work for me
thanks newquaymarc
ive done that now ive got a low light page that says
"serial" at the top
"v1.03" at the bottom
any idea what i should do next?
Oooh upgrade seems to be installing \o/
Thanks
would you happen to know if there is any way I can manage my contacts from the pc? i searched activesync and there appears to be nothing there. My old motorola bought up kind of a virtual phone on the pc and managing and adding contacts was easy.
sisfis said:
would you happen to know if there is any way I can manage my contacts from the pc? i searched activesync and there appears to be nothing there. My old motorola bought up kind of a virtual phone on the pc and managing and adding contacts was easy.
Click to expand...
Click to collapse
Are you serious? Outlook/Contacts! Nothing easier.
hi again
ative sync should kick express in and that will manage contacts/calender
would using thunderbird as the default email client **** this up then?
sisfis said:
Hi
Unfortunately I was in the middle of upgrading the software to version 172181 when I decided, for some strange reason, to pick the phone up out of the cradle and make a call. DOH!
I can no longer get the phone to boot up / turn on it is just stuck on the low light o2 backscreen and shows
r 1.17.00
g 1337.20
d 1.72.00wwe
Im quite literally just stuck on that screen, the phone wont seem to reset, reboot or hard reset or turn on or off.
I assume im doing the hard reset correctly on/off button and reset button with stylus.
I did see somewhere to use the on/off button, camera button, record button and reset button with stylus but this does not appear to work either.
I don't know whether the condition is terminal or not but anyone can help i would really appreciate it I have a lot of information on there that is very valuable to me.
Click to expand...
Click to collapse
i was attempting to upgrade this xda that i just bought to this same version. is this the newest one? what version of windows is it? i got an error in the middle of the upgrade now it just shows the connection type at the top of the screen and V1.01 on it. tried the UpgradeUt_noID file but it says that it cant connect after about 3 minutes
sisfis said:
Hi
Unfortunately I was in the middle of upgrading the software to version 172181 when I decided, for some strange reason, to pick the phone up out of the cradle and make a call. DOH!
I can no longer get the phone to boot up / turn on it is just stuck on the low light o2 backscreen and shows
r 1.17.00
g 1337.20
d 1.72.00wwe
Im quite literally just stuck on that screen, the phone wont seem to reset, reboot or hard reset or turn on or off.
I assume im doing the hard reset correctly on/off button and reset button with stylus.
I did see somewhere to use the on/off button, camera button, record button and reset button with stylus but this does not appear to work either.
I don't know whether the condition is terminal or not but anyone can help i would really appreciate it I have a lot of information on there that is very valuable to me.
Click to expand...
Click to collapse
It's bcoz the flashing/upgrading/installing of ur fone seems not to be finished. Always follow instruction. If you really want to do something, think twice so you never messed up. nweiz, try to load it again in bootup mode and re-flash it. there are a lot of ROM for the Himalaya, you can download one. Try to search. again, FOLLOW INSTRUCTIONS!
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
kameisama said:
So here's a peculiar incident:
I have a CDMA TP with a stock ROM and a few basic apps I gathered from these forums and others. I've had it for less than a week.
Tonite, I went to check my text messages. Suddenly, the screen went black and the phone stopped responding. After pressing the power button and fiddling with the keys, I pulled out the stylus and did a soft reset. No response. Confused by this, I tried again, but still nothing. I removed the battery, and turned the phone back on. It froze at the "Touch Pro" screen with the rom/radio/etc info at the bottom. After repeating this a few times I decided to do a hard reset. So, I turn the device on and perform the hard reset. By this point the TP is only turning on SOME TIMES, and I have to take the battery out and put it back in often just to get it to start successfully. So, I finally get the device to boot up and it starts to configure WinMo. Suddenly, while configuring, it freezes. Now I try to turn it back on, and nothing happens.
Basically the device is stuck like this, shifting between not turning on at all and turning on but freezing at the "Touch Pro" screen.
So, my question is, what the heck is going on here? Has anyone else had this problem, or does this sound familiar to anyone? Any help would be greatly, greatly appreciated.
p.s. Yes, the battery is fully charged.
Click to expand...
Click to collapse
Time to take it in and get a new one.....
Same problem here phone started b not coming out of lock mode. Backlight is on but no display on screen (if i tilt the screen left and right i can see light coming from behind) did about 6 hard resets and still same problem. also power button works whenever it wants to. this phone sucks @ss, i want my mogul back. on a second note my replacement will be here on wednesday.
Touch Pro stock rom purchased back in nov when it came out
yeah, i've had the same problem, i found if i hit my phone on the back or side and then batter pull and hit the soft reset while off, not the power button to turn it back on, it comes back on with color on the screen not just blank black screen with backlight, this works mostly every time, but when it doesn't, i just hold the power button down and do battery pull and hit the power button and it works, its like its got a combo of things you have to do before it works.. weird
Boot Up
I have also had similar problems. I for some reason sometimes have to remove my SD card and boot up without it for some reason. Not all the time, but every once in a blue moon. Not too sure how that affects anything, but you may try that too.
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Mayonesa said:
well i started a thread here ***help*** because i kinda have the same problem.
i downloaded some cabs, nothing fancy but i had some problems with a theme i downloaded. when i went to deleted i couldnt..... to make a story short, i took it to the sprint store where they tried to do a master reset/ hard reset and it wont take it. it wont do a thing... they say some important files are missing...
the phone works but not the way it should... the time on the home screen wont show up. and some other small things...
dont know how this happened but i would like to know... im worried about new programs to the phone now. ( getting a new one)
still want to see if i can fix this one.
Click to expand...
Click to collapse
Have you tried re flashing the ROM?
it wasnt HTC's fault for your phone's not booting...thats what happens when u try to mess with the hardware too much and you dont know what your doing
Would you want to sell???
Reboot Brick HTC process
****DOn't take battery out after hard boot***
1.just watch videohttp://www.youtube.com/watch?v=sk56olMkCtU and do what they do but dont take battery out. LEAVE phone STUCK on BOOT screen. Nothign else will move or work but you want phone just like that.
2. connect usb cable to active sync. (this may not link up but leave usb connected anyhow) Do not delete phone profile.
3.use rom like Download MightyROM6_Herman.exe avail at: http://www.lilrico.com/Mighty/mightyromblog/?p=454
4 although active sync is still attatched but may not be connecting. It will connect thru usb anyway when you run the rom software. http://www.youtube.com/watch?v=fV2I2WAFkg4&NR=1
This worked and kept phone from cutting on and off. and restored ROM. don't know about original htc boot. but your phone will work under this rom for now and you can go from there.
hey thanks plain ole dumb, it works now.
man I thought it was over.
thanks again
Hi..
i used the search but could not find anything..
I am having some issues with eh phone..
it freezes up when even i want to use it..
i can use it for a few minutes and then freezes up.
everything goes really slow or just doesn't react.
i didn't open anything special
just tried a hard reset..
only added google maps but didn't open it.
have exchange and hotmail syncing.
that's it..
soft reset helps for a few minutes and then it crashes again..
i really have no clue why this happens..
does anybody have a suggestion that i could try?
Thxn!
Well, could be simply a hardware problem (either a faulty one or f.i. a loose connection after dropping it).
Do you use your S740 only since a short while (new device) or have these problems started after a while ?
I use it now for a year and 4 months (actually with quite a few apps installed) and it's incredibly stable.
Sometimes it gets a bit slow, and then I do a soft reset.
But thats maybe bi-weekly.
I suspect that using McGuider navigation software alongside other apps (like Opera mini/java and Audio Notes and always bluetooth on) is the cause most of the time.
Only with SmartToolkit I had some structural problems of freezing.
There's one thing you can try:
I did read in some cases with people with serious problems, who needed a hard-reset, that only after a few hard resets their S740 again worked as new.
So try a few more hard-resets.
good luck
peseta said:
Well, could be simply a hardware problem (either a faulty one or f.i. a loose connection after dropping it).
Do you use your S740 only since a short while (new device) or have these problems started after a while ?
I use it now for a year and 4 months (actually with quite a few apps installed) and it's incredibly stable.
Sometimes it gets a bit slow, and then I do a soft reset.
But thats maybe bi-weekly.
I suspect that using McGuider navigation software alongside other apps (like Opera mini/java and Audio Notes and always bluetooth on) is the cause most of the time.
Only with SmartToolkit I had some structural problems of freezing.
There's one thing you can try:
I did read in some cases with people with serious problems, who needed a hard-reset, that only after a few hard resets their S740 again worked as new.
So try a few more hard-resets.
good luck
Click to expand...
Click to collapse
Thank you for the reply..
its not a new phone..
worked perfect the last couple of months.
this just started this week..
I will try doing a few more hard resets.
Hope that works...
Thanks so far!
Hy
I had the same problems after Hard Reset.I fixed it by Loading the akku to 100%,Switching off the phone,Removing the akku,Removing the SIM,Removing the StorageCard,Insert the Akku,Hold Down the Volume down button+the button in the middle of the cursor und short press on the power button and folow the text on the screen!Let the phone finish all and let it reboot and let it install all the original stuff!After a few reboots and when the phone seams to be finished you can install the Sim and start the phone again,let it install all the provider stuff,when its finished you can install the Storage....if you let the sim and the storage in the phone and make a reset something wents wrong at installing!
MFG
So by accident I launched a CHT file from my SD Card which essentially crashed sense. No biggie, did a hard reset and thought I would be okay.
Wrong.
When I hold down the end key (to either load johcos' end key or even if i uninstall it) my screen is dead. The hard keys work, but not the screen.
Anyone have a suggestion? I have been using tmo-us stock rom without problems until yesterday when this started. I realize I could flash a new rom and maybe it is time...but tis very annoying this is happening after a hard reset.
Thanks.
still not working after flashing energy rom
argh.
flashed energy.
same problem.
now have to work...but any suggestions? my long hard key is dead and freezes my phone. hard reset/ new rom did nothing.
thanks.
same with android
so now anytime my phone goes to lock screen the screen stops functioning though the hardkeys work just fine.
thought i would try android and be savvy...but wrong.
same problem.
any ideas? i am ready to take a hammer to this damn thing...
This recently happened to my GF's phone, She said she was just playing a game one day, it froze so she popped the battery out and rebooted. Now every time she uses the End/Power ( red ) hard button to shutoff or wake up the device, the screen stays locked and won't respond.
I have tried soft reset, hard reset, different lock screens and what not. The only solution I found, besides sending it in, is to let the screen shut off by itself, and then wake it up with the Call/Send ( green ) hard button.
You can also try using the End/Power hard button to lock it, but then as long as you wake it with the Call/Send hard button it should be fine.
It has worked every time now. Try it and see if it helps! It's a little annoying but it saves money and insurance!
Going to repost this in all those previous listed threads to see if it helps anyone else.
Good Luck!