Hello, i'm new in this forum. I have the following problem: I have to install a MDA II on a PC in our company, but for security reasons i have to disable all communication functions like blue tooth and internet before doing this.
Is this possible? How can I do this?
greetings,
xda-developer
If it's for security reasons then don't connect to the PC.
Other wise how secure will it be. If you hack the registry for bluetooth and take out the sim for phone (to inhibit internet access) then that person can put in a SDIO with WIFI or Bluetooth an yet has communication oppertunities again. Or he can put in another SIM so the phone is up again.
Most of above is also valid if you would give that person a plain PocketPC.
Regards,
Mark
if you disable phone and bluetooth then why get a xda2 at all ?
@markutah
thank you for your answer. I have to connect the MDA for synchronizing email and contacts with Outlook. Although Internet and Bluetooth have to be deactivated, the phone-function must still be available.
I thought of deinstalling or hiding the Internet Explorer in the registry (the user isn't skilled enaugh to modify the registry to turn on again). Unfortunately, I have no idea for doing this. And I have no idea how I could disable bluetooth.
@Rudegar
A user (the chief of our company) have bought a MDA II from T-Mobile (and he really don't care about our security policies). I'm not allowed to change or ignore these policies, but on the other hand I have to connect the MDA to the PC. :?
I think Internet is easy: In the connection profiles on the Proxy settings tab uncheck "this network connects to the internet".
This must be done for both work and internet profile.
But for bluetooth? I can't help you. Maybe a little bit stupid but instruct him not to turn bluetooth on would I say.
Mark
how will se be syncing with outlook ?
if by usb then no problem
about bluetooth then there are some posts in the forums if you search where people give the registry values you have to change to disable bluetooth and remove the icons (of cause by reversing those changest he could turn it back on unless you remove it by hammer and screwdriver )
about grps then you can just delete the settings in
settings connections -> connections and remove the extry's regarding grps
of cause if he want he could just type them back in
but another way is to get the phone company to block grps
on most cellphone company's it's not enabled as default and you have to ask them to turn it on, so i asume you could ask them to turn it off
the buttomline is that you can make anything 100% secure
Thank you all very much. The MDA is connected to our network now.
greetings,
xda-developer
Related
Hi Guys,
really dumb question ... how do you disconnect from gprs once connected ?
I can not see an end button anywhere !!!
cheers
i have just worked out that if you disable phone, it turns off GPRS...
surely that is not the correct way to do it? :roll:
sorry to nag .....
does anyone know how to cut gprs once connected ??
maybe its so obvious, noone knows it !
maybe its so easy, no one can be bothered to write ?
let me know please !
install monitor
Install the spb gprs traffic monitor is the answer.
You can also simply tap the signal sign (at the top of today screen), it'll show your GPRS connection and then you can simply tap end buttom Cheers
not on ppc2003 .,... there is no end button on the signal sign :-(
Install the spb gprs traffic monitor is the answer.
-----------------------------
is this the solution for PPc2003 ?? surely there must be an inbuilt feature which allows you to disconnect GPRS without the need of installing other software ??
please advise
I have the same problem and i asked in deffirent places in this forum but no anwser till now.
ARZLEB said:
Also i have a problem when connecting to GPRS there is no d/c button i had to push long the red close button to d/c my GPRS session after 5 seconds exactly i will loose service signal i have to turn off/on phone to re obtain signal!
any one noticed this?
:?
Click to expand...
Click to collapse
I hope someone would anwser this!
Can maybe the developers step and and show us the light?
Much appreciated :wink:
now have you got ppc2003 to connect to uk 02 grps?
what the correct settings as i can not get mine to connect at all
please pass the on
hi grim,
sorry mate, i only use Orange Gprs :?
try
Homepage: http://pda.o2.co.uk/
APN address: mobile.o2.co.uk
Username: mobileweb
Password: password
Email servers (POP): mail.o2.co.uk
Email servers (SMTP): smtp.o2.co.uk
DNS Servers: 193.113.200.200 and 193.113.200.201
nope I can not get it to connect to grps at all
i must be doing something wrong? anyone done it ok to 02 uk grps?
This appears to be a "new feature" of WM2003, always on GPRS . It does seem to timeout the connection after a little in-activity.
I'm in the same boat and cant for the life of me imagine why they have programmed this way. I can only imagine it's a bug and will be fixed.
Thought I was just stupid
We'll technically I am I was soft restting to stop it to start with
Looks like I'll have to put on Spb mon
You can also turn off the phone (tap the reception button and click "turn phone off"
and turn it back on !
also cuts GPRS
Right, Ali-Butt, it's also the way I do it ! : turn the phone" off",GPRS is also diseable, then come back to put the phone "on" ... if someone find a better way :idea: ....post-it please
Well the best solution i discovered is to use Sbp GPRS monitor, since you wont benefit from the Auto Connection / Disconnection while checking your email since the device will connect but never d/c. So all connections and d/c and done manually by you instead of using the Off / On methode use the Disconnect button in the GPRS monitor for the time being until they find a solution for this bug and yet you wont have to turn to phone off and on, consume power or someone calling in this exact min to find that your phone is switched off.
If you dont have Sbp GPRS monitor i am whilling to share it with the ppl having this problem.
:wink:
I've installed 2003 and it's all great. A few problems with the syncing but after 3.7 (strange, I had 3.7 anyway though since I've reinstalled it off the MS website it looks different to the 3.7 it used to be??) it did eventually work. Scary few mins though!!
I bought All-locations GPRS counter a few months back, but the one thing it doesn't really have is an end connection button. I also bought SPB's PocketPlus but it's saying that it's not compatible with PPC 2000????? Does anyone else have this problem? I've tried logging onto their website but it seems to be down all the time. This program used to automatically cut the gprs connection if say I'd loaded MSN and then shut it down. Very handy!! If anyone knows how to get past this or where they've put an update to work on 2003, please let me know.
In the meantime ARZLEB, if you could find it in your heart....
Cheers
V
'Always on' is a great idea, PPC2003 can disconnect automatically and re-connect when a phone call comes in so why is it an issue? The only reason I can think of is cost (if you have something polling the internet racking up MB's).
For delivering mobile applications and corporate push E-mail, this feature is essential.
These devices are not really targeted at the consumer market more at the business user so the carriers will love this feature to deliver extra services and generate GPRS data revenue.
Hi All
the best solution is the easy one , simply press on the hardware button ( the red button ) for about 2 seconds and it will disconnect the GPRS Connections !! easy ha !! :wink:
Cheers
Ahmad
Is it possible to sync using activesync over the internet without running an exchange server? I'd like to be able to sync my XDA while I'm out and about to my PC at home.
:shock: :?: :?:
been trying to do the same for ages , but never found out how to do it
It can be done, under a few conditions:
1. You need to have a static IP address for you PC
2. You need to install Pocket Hosts or a similar free utility to map the WINS host name to your PC's IP address.
3. Your carrier / ISP must not have a firewall that blocks ports 5678 or 5679 (T-mobile seems to block this)
Remote active sync was designed with a local area network in mind and it is configured to connect to you computer by using the WINS name and not using an internet based DNS name. When you connect over an internet connection from your XDA, it is not able to find you PC.
If you install a free utility such as Pocket Hosts (http://zimac.de/cestuff.htm) you can configure the Pocket PC to be able to find you PC. This utility will allow you to configure you Pocket PC to map your PC Name to an IP address (similar to the HOST file on a Windows based PC)
Before I had the unlimited GPRS plan, I created a dial up connection to an ISP on my PocketPC Phone and it works perfectly. However, when I try the same thing over the GPRS connection, it does not work. From my end, it looks like T-Mobile blocks ports 5678 or 5679 on their firewall, which are the ports that remote active sync uses to complete the connection. (It looks like it is about to work, but then fails to complete the connection)
I have tried to convince t-mobile to fix this, but they keep claiming that it will not work out of the box, they don't know how to make it work, and they won't support it. They try to "upsell" me the sidekick or other device. I can't seem to get through to the right people. It seems crazy that a setting on their end blocks us from being able to sync over the air. After all, what is the point of a data connection if you are still restricted to using a cradle to sync. I understand that they don't want to support this and walk people through setting this up, but blocking the functionality seems pointless.
Anyone tested this on ATT? With number portability starting, I may have to explore other options. Anyone have an in at T-mobile that can get them to open up these ports on the firewall?
try www.yahoo.com
get an account (if you don't have one already)
login -- click on mail
the click the tab for addresses
on the next line to the right you will see the word "sync"
this will take you to download intellisync for yahoo
then follow instructions
sync you pda and your good to go, you will have your info on the internet and sync from anywhere
one more thing if youown a palm os and a pocket pc pda and you want to have both devices with same info (contacts, mail, notes etc. etc.)
the change the settings on your intellisync for your other device and resync
hope this helps it did for me...
Hi, I'm from the Philippines and my Network is SMART Communications. I tried synching with my active sync via GPRS but it seems it can't find my PC eventhough I used Pocket Hosts utility. It seems they block the port too. Anybody from Smart to please open the gate for us.
I've setup up my Win2k PC as dial-up server. And with the help of the Pocket Hosts utility, I can now be able to sync my Outlook over the air. But the call charges is killing me.
Jose
I've been investigating this myself too - and have to say T-Mobile's attitude is also alive and well here in the UK on O2 (via crapphone-whorehouse data support team).
I was actually shouted at by one of their 'tech' guys when I tried to persuade them that it could technically be done, but I needed to find out whether they were blocking the relevant ports. He eventually hung up on me! Fantastic service, eh!
I've been trying to get ActiveSync working over the Internet for the past few days and have finally managed to get it to work reliably. There are a couple of things that I have found...
Firstly, at least one of the ports required for ActiveSync does seem to be blocked when using GPRS (Vodadone UK in my case). Setting up a normal dial-up ISP connection results in first time connections to ActiveSync every time. It would be nice to know why there is problem over GPRS.
Secondly, my device was still connecting as Guest. Whilst reading through various other forums I found a fix that seem to work for this but it involves deleting a registry key. I wouldn't recommend it as I have know idea what else this key might be used for but it certainly solved the problem for me. The key I removed is HKLM/Ident/Username value is guest. The key is replaced automatically at some point (maybe after a reset) so if it stops working, you have to go and delete it again! There must be a better way....
That's great information, thanks.
I now have my device remote synching!
Just to summarise my steps to get things working on my XDA II:
1) XDA: Set up new work connection (don't you just hate the organisation of conenctions...) to a dial-up ISP over GSM, as O2 UK also block the ports required for activesync.
2) PC: Open sockets 990, 999, 5678, 5679 on my firewall
3) XDA: Use pockethosts to set up the IP address for my PC name
4) XDA: Change HKLM\Ident\User from guest to my normal PC logon user id
5) PC: Set allow network connections in activesync
6) XDA: Manually Connect to the ISP connection
7) XDA: Open activesync and click synch - away we go!
As an update to this, I had to do a full restore at the weekend after loosing all my data on the XDAII. The problem was not related to these changes but it made me look again at the Ident key. There are two keys normally like...
HKLM/Ident/Name Value<Your chosen PDA Name>
HKLM/Ident/OrigName Value<Pocket_PC>
This time I changed only HKLM/Ident/OrigName to the same value as in HKLM/Ident/Name and it connected first time. Also, this value does not seem to be reset unless you do a hard reset on the device. This may be better than changing the Username value though I have yet to try either on another computer where my preferred connection should actually be as a Guest.
Got it working
Thanks to andyclap's suggestions I finally got it working. It looks like T-mobile does not block any ports, but without the registry hack the error I got was the same as when I tested this over a dial up connection and blocked the ports on my firewall.
The other change since my last post is that I am using WM2003 and it requires you to set up a VPN connection to the PC instead of just using PocketHosts for the name resolution.
Every month I have paid much money for phone and internet fee(9800 yen). I want to disable internet connection because it is not necessary for me.
thanks in advance
you can create a new internet connection and replace the default with it.
thanks for reply but how to make new connection.
Hello. What do you mean? You mean I can use it for a non-softbank account? (via 3g?) Of course, I suppose we could just delete the whole softbank account, and therefore it would not be able to "connect" via 3G, and we could connect via a wireless account, but then softbank mail would not work, right? I wonder if it is possible to just disable connecting to the internet via explorer.... any ideas?
@taicyber: i ran into a similar problem. sometimes while in my carrying case, my keitai would connect to the internet via internet explorer, and my monthly fee for internet usage was much higher than it should have been. so i took a couple steps. first, i changed the internet button on the front of the phone to a different function (that's apparently the button that often gets accidentally pressed). after that, i changed pie's (pocket internet explorer's) start page to a local file (ie. the help file). that step solved the majority of my problems. what was happening when it auto-connected was that yahoo.co.jp was the start page, and that page has HUNDREDS of little pics and ads that refresh every few minutes and drive those packet amounts up. if you make it a local file you'll no longer have those mystery packets being sent. and it doesn't affect your mms/sms in any way. having the dummy file as a start page made it safe for me to change the pie button back to it's default function of opening up pie.
also, just for reference, i don't think you have to worry about the phone being connected to the 3g network too much. unless a page that refreshes itself frequently is opened, then no data is sent. the only problem i run into with 3g being connected is that it kills my battery faster.
thanks shunsai. I have experience like you said. and I also changed the button and defalult.html(in /windows).But I am not sure if my phone will connect internet via other way.
Hey it might not be super helpful in this case, but for me I disable gprs using a piece of software called 'NoData'. it will let you quickly switch on / off data connections. Search the forums for NoData and you'll find links to it.
The issue sounds specific to Softbank the carrier though so YMMV.
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (for the Hermes). It should currently be "BTPAN1".
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc")
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. I imagine this will drain your battery in a hot minute, so bring your charger.
UPDATE (28-Oct-2007): Attached are some more beta releases of patched intshare.dll. I've created versions for most of the adapter names people have requested. By renaming this dll to intshare.dll and copying it to \Windows, Internet Sharing will use TIACXWLN1 (or whichever dll you use) when Bluetooth PAN is selected. I.e., if you use this, you will not need to make the registry changes above.
This will handle the registry part, but of course you'll still need to set up the ad-hoc network on your own.
UPDATE (03-Nov-2007): I've attached a beta version of the patched Internet Sharing app. It's in its own cab so it won't overwrite your existing IS. This app replaces Bluetooth PAN with 802.11b/g Wireless Ethernet. No registry hacking required. This app is well suited to replace the MS version on cooked ROMs.
If you use an adapter other than TIACXWLN1 then replace intshare.dll just as before.
UPDATE (08-Nov-2007): Attached is v 0.9.1 of the Internet Sharing Mod. This update addresses the 10 minute disconnect bug most people have experienced.
best,
fluxist
This is the first thing I'll try when i'm at home again!
I can't believe this! Waiting for this since i got my Hermes. Thx for this development. This is the greatest effort since Hard-SPL and WM6 upgrade.
Now I can connect my XBOX360 to the Internet without starting my PC and sharing it over PC-LAN. USB-Charger is at the Front of the XBOX360.
I hope it will work.
You said the Max-Connections can be reworked. Does this mean it will support Ad-Hoc AND WLAN-Routing to many recepients too?
This worked for me too on a Kaiser/TYTN II
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
odessaranger said:
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
Click to expand...
Click to collapse
not sure what you mean by replacing the connection. With ICS, obviously you cant share your connection over BT while sharing it over WIFI. and you can normally use wifi to connect to another computer by using an ad-hoc connection and manually entering a private ip on the same subnet for each computer.
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
boniestlawyer said:
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
Click to expand...
Click to collapse
Were you able to use more than one client connected?
I'll admit..when I saw this my first thought was that this was another "How can I do internet sharing via wifi" and the title was just misleading..instead I find myself very impressed with your accomplishment. Very well done! As a "hack" untill you figure out how to mod the dll which I'm sure is only a matter of time now that you have pointed everyone in the right direction, you can export the registry key for both the Bluetooth adapter and the Wifi one and "import" whichever one you want to use at a given time...it's not pretty but it should work.
Some issues of concern would be that the AP is wide open and can be connected to by anyone with no password etc...the bluetooth pairing allowed some security but using the wifi doesn't have the same shared key protection...or am I missing something obvious?
fluxist said:
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
When I used it I was only able to get one client to connect, however there is a reg value, HKLM\Comm\BTPAN1\Parms\MaxConnections that may help if it is changed from 1 to 2 (or whatever). But I haven't tried.
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. So that's a good thing, although I imagine this will drain your battery in a hot minute, so bring your charger.
I was going to release a patched intshare.dll so that the normal Internet Sharing utility can do this, but I'm having trouble changing the section addresses in the dll to the right values after I add data. If anyone knows how to do this PM me and I'll give you the details.
best,
fluxist
Click to expand...
Click to collapse
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
I ran into same issue with XP internet sharing. Another workaround is to have a linux machine do NAT( since you can specify the IP used there) to whatever other clients you want and have it connected via bluetooth dun or bluetooth PAND (which is the solution I use to give internet to my replaytv and a couple of laptops in the house)...my edge connection is my main internet feed..a cacheing proxy such as wwoffle, squid of my personal preference "polipo" helps alot to when using gprs/edge etc since it helps with the latency.
fluxist said:
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
Click to expand...
Click to collapse
Impact on BT?
What a brill find. Well done.
Does it break anything with bluetooth?
Tx
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
if someone manages to get this working with xbox 360 make a tutorial plx ;D
superflysocal said:
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
Click to expand...
Click to collapse
thats what i wanna know , could i use my hsdpa connection via wifi to my psp?
I'll do a tutorial when i'm at home again. Maybe somebody with know-how can make a cab-file v1.0 for this "WLAN-Modem hack".
This surely will be a great app.
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
when you say click "IEEE 802.11b/g Compatible Wi-Fi" do you mean the wifi network adapters in my case would be "tiacxwln compatible wireless ethernet"? im trying it on a 6700 WM5
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
Got it - except on my device it's Programs -> accessories -> IS
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
Check - but is the T1ACXWLN1 device specific? If so, how can I find the interface ID on my device?
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
For me it's settings -> connections -> network cards, but I don't have an IEEE 802.11 listed. I connected to an existing AP, and found that my 'SDIO WLAN Wireless Adapter' does receive a DHCP address, so I tried changing it to 192.168.1.1...
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
Found this and set up my WING-FI network.
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
The client PC connects to WING-FI, but never receives an IP address...
What could I be doing wrong? Is it the hardware ID in the registry? I've created the network with WPA, then after the connection problems, with no security - but still no change.
Thanks!!
Ryan
neonstorm said:
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues...
Click to expand...
Click to collapse
Very likely the string TIACXWLN1 needs to be something different. Check HKLM\Software\WZCSV\Parameters\Interfaces\
There should be a key there with the name of your wireless adapter. It should end in "1".
And if not there, it should also be visible under HKLM\Comm\
Let us know how it works out.
EDIT: I just noticed you typed T1ACXWLN1. The string must be TIACXWLN1. That's "i" not one.
fluxist
I own a PPC6700 as well and I was able to get it working no problem other than the fact that our wireless adapter is not the same as the one mentioned. The reg edit is the same it's just the first network adapter in the list when you create the network settings.
fluxist said:
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
Click to expand...
Click to collapse
If you send me the dll I could look into it.
i have some experience with editing dlls.
good work man
Ma Ameo X7500 Is Automatically Connecting 2 Internet Every Time And Am Loosing A Lots Of Moneyn
How Can I Jus Disable The Option Like Connect To Internet When I Want Or Something Like That
Go to www.modaco.com and download nodata.cab
You may need to ask yourself 'why is it connecting' and why is it costing so much?
Generally, if you have a POP3 email account, set up, it will connect at the interval you have set in Activesync or Messaging.
The X7500 also has QuickGPS which will try and update itself at intervals- the actual data use it tiny though, so should nt cost much. To stop it, open QuickGPS and alter the settings.
Do you have any other programs that connect to the internet? Do you want them to only connect via WiFi- if so, the link by Confucious is excellent.
If you want to use GPRS data sometimes, you need to modify the connection settings and remove the Password and untick 'Save Password'; this will mean that any connection attempt will always prompt for a password, which you can then abort if you want to (of course if the connection attempts are frequent and you can't trace the source, this could become a pain in itself!)
Confucious said:
Go to www.modaco.com and download nodata.cab
Click to expand...
Click to collapse
THANKS FOR UR ATTENTION 2 MA THREAD
THAT HELPED
NOW ITS NOT CONNECTING LIKE THAT
NeilM said:
You may need to ask yourself 'why is it connecting' and why is it costing so much?
Generally, if you have a POP3 email account, set up, it will connect at the interval you have set in Activesync or Messaging.
The X7500 also has QuickGPS which will try and update itself at intervals- the actual data use it tiny though, so should nt cost much. To stop it, open QuickGPS and alter the settings.
Do you have any other programs that connect to the internet? Do you want them to only connect via WiFi- if so, the link by Confucious is excellent.
If you want to use GPRS data sometimes, you need to modify the connection settings and remove the Password and untick 'Save Password'; this will mean that any connection attempt will always prompt for a password, which you can then abort if you want to (of course if the connection attempts are frequent and you can't trace the source, this could become a pain in itself!)
Click to expand...
Click to collapse
THIS IS ALSO A PRETTY GUD INFO
LET ME LOOK THROUGH
THNX MAN