[XDA/MDA, PPC 2002, O2/Mobilkom Austria]
Hi developers,
In the evening I took my XDA into the docking-station for realoading the accumulator. On the next morning I removed the XDA and suddenly there were only coloured vertical stripes and horizontal banners an the screen. The hole night the XDA was also connected as so many times before to my notebook, wich was also realoaded.
Except this problem the XDA runs without problems. I am able to control it with my notebook in combination with the "Pocket Controller".
Suspect 1: The problem appears exacty at the 11.9. in the morning.
Suspest 2: Some hours later after the "therapy" (see later) the display ran normally for Display about 10 min..
"Therapy":
1. I removed the four sceews backwards and fixed it again (it helped two times in the last after my XDA felt on the floor - there were simelar symtoms)
2. I removed the backwards-cover and the only screw (black) inside i saw.
3. I checked the contacts by view - ok
4. I closed the cover, then Hard-Reset, Installed the backuped system-informations with activSync, then Hard-Reset again, 15 Min. reaload
--> O WUNDER: The display ran for about 10 min. normally, than stripes again
5. Many hard- and soft-resets
6. Virus-Check with "PC-cillin for Pocket 2.0"
7. Shaking & knocking
NO SOLUTION.
Does the XDA (1) have a backup-battery and where?
Does anybody have some ideas?
Please help..
I like so many other have recently received my gTablet. I have done nothing so far except to charge it and start it to become acquinted with the interface.
When I powered on this morning the system seemed to hang at the gTablet logo. After about 1 minute I pressed the power on button to power off. The next time I restarted I had to go through the whole startup sequence again.
The only thing I noticed that changed is the background. Before it was leaves falling on water, now I have a ocean view.
Has anyone else experienced something similar?
Thanks
Yes, this happened to me too. I updated it, and after two or three startup/shutdowns I got the setup wizard. I did not get this when I started it up the first time.
I then found that I needed to re-install flash. The wallpaper can be changed back by long pressing the screen and selecting Wallpapers -> Live Wallpapers.
I probably know this may be a hardware issue, but wondering if anyone has found a remedy--did a search and cannot seem to find if anyone is experiencing the same problem(s).
Bought used SGS2 that had Cognition 1.6 on it, Flashed Checkrom HD, Flashed back to stock JI3 w/ new bootloader and left un-rooted.
-Screen turns on after screen timeout (15 seconds or 30 seconds)
-Changed to pin unlock--same thing--turns on and remains on
-Screen won't go black/back to screen timeout
-If i push the power button, screen turns off, then after about 20 seconds or so, screen turns back on and stays on
All reboots remain the same, pulled battery, remains the same--screen comes back on. Completely drains the battery
Any ideas? ????
I'm afraid i don't have a warranty and i've already tried contacting this pitiful seller...
***********
Update: 12/1/11
- Replaced USB Flex cable purchased from ebay, but it was version 2.1 instead of 2.2 that i replaced
- Issues of screen randomly staying on is for the most part, gone, except i've woken up to the screen being on a couple times w/ a text message (and screen stayed on)
- Cannot connect to USB via download mode anymore
- Cannot connect to PC (states unrecognized)
- I get random "Back button" presses while using an App or the browser--sometimes multiple times where it goes back to the home screen
- Charging is slow and only reporting "Charging USB"
- Purchased another one from a different Ebay supplier--hopefully, it's version 2.2
*********
Update: 12/12/11
- Replaced with 2.2 revision flex cable from ebay seller yqmama
- Cleaned flex cable connections on main PCB with electronics cleaner
- Charging is now saying AC when plugged in
- Download mode and Recovery via USB work flawlessly
- No other problems seem to be apparent, except the back button went crazy once since replacement
- Seems that the phone is now ready for daily use
My guess would be a rogue app causing it. Have you checked what's waking the phone? Something like BetterBatteryStats should be able to help you pinpoint it, if that is indeed the cause.
If that's not it, at any point have you tried factory resetting the phone?
If you're using JuiceDefender, make very sure you disable the timeout function. It's known to turn on screen by itself.
Sent from my GT-I9100 using Tapatalk
I literally have no apps installed after i did a factory reset, and i formatted usb storage. I can try betterbatterystats, but i feel like i'm almost at a loss.
Update:
-Installed CM7 nightlies and random screen turning off and on went away, but new problem--capacitive buttons would not work
-Installed CheckRom 3.3.1 and all was going fine 11/15/11
-Installed apps (didn't use TiBackup) from market
-Installed theme from KitchenPro (ICS Domination)
-Added widgets from homescreen (added SamsungWeatherClock--i.e. accuweather)
-Went home, connected via Wifi
-Saw screen turn off and on several times
-Used Watchdog--came up with Event/O and Suspend as acting up
Are these what is causing my screen to wake and stay on sometimes??
updated 1st post w/ findings thus far after replacing USB Flex cable (charge port)
Have a very similar problem as you describe with a water damaged Galaxy S2. I replaced the USB flex cable and it solved the problem I was having with the phone refusing to stay off. However, the screen will not turn off, when I briefly press the power to turn the screen off, it goes off for a second and then it turns back on. I am going to be replacing the home button flex cable when the part arrives. When I open it up to do that, I will be cleaning more parts in hopes I can solve the screen-no-stay-off problem that I'm having.
****UPDATE.
Used a bit more contact cleaner on some of the areas I had overlooked, put it back together and the screen's behaving nicely.
My Note 8 battery went flat and when put on charge the screen started flashing.
Overnight it had charged 1% when attached to my computer so I plugged it in all day.
Eventually it charged, but was playing up. Kept dropping wifi, apps would not run, could not download anything from the Play Store.
I did a factory reset and it appear to be ok, except I have a transparent, grey box covering about one third of the screen with text in it relating to the device.
i.e.
PDA:N5110XXCMK1
PHONE:NA
CSC:N51100XACMJ2
H/W:Not Active
RF Cal Date: None
SMD:01N,PBA:04N,CAL:07N,FINAL:11N
and a load more.
If I scroll the screen the background scrolls ok, but this box stay put.
If I open an app it disappears, but going back to the home screen it reappears after a couple of seconds.
I tried taking a screen shot, but it disappears when I try to do it and does not show up.
I guess I could take a picture with my phone if that would help.
Any ideas what has gone wrong?
Thanks
Hi all,
I own the pace from roughly dec `17 - Jan `18. the watch has been working more or less properly (with some major GPS height deviation).
I upgraded the watch last week to 2.8 OS and it seems to be working OK.
today, after the shower, the watch all of the sudden showed a dimmed display and after 30-60 min, it became blank and after 1-2 hours 2 white spots appeared on the screen.
the watch is still connected via bluetooth to the app, but no display is shown (only backlight is operational via the power button).
I tried flashing the 2.8 OS (and others) via the ZIP files which contains the automatic batch files and the ROM files, but it is not completing...
can anyone help?