sorry if this has been posted before, but i have searched the forums and the net for an answer.
i have an xda 1 and recently upgraded the radio stack to the latest o2 version (i installed the 15mb one)
afterwards, i can no longer charge my xda. i cant install any other update as i dont have enough power to install them
is there a way around this?
You have a very little chance to repair your Wallaby. :-(
read through this topic:
http://forum.xda-developers.com/viewtopic.php?t=4123&highlight=
Related
I was upgrading my Siemens SX56 with the XDA SER 1.2 via USB. It started well, it read the version etc. Then the screen of the PDA went to the upgrading state (might take up to 5 minutes). Then I received a message that the program could not communicate with the device or something like that (I dont remember the exact message bacause I was scared and clicked ok)
Then, the most horrible thing. The device was there in that upgrading state, I had to take it out the cradle. I reseted it and it was the same screen.
Is there a way to make it live again?
no solution?
searching through the forums I saw a lot of users with the same problem. Is that there is on hope for us?
I will pay to someone to point me to the right solution. pleaseee help!
have you tried the SD-card method (with XDA Tools)?
should be easy as pie
Hiya All,
I tried to upgrade my xda 2 with the new ROM upgrade (Xda_II_Upgrade_v16050.exe) and now its dead. I connect my XDA2 to my PC, double clicked on the EXE and followed the prompts. I then had to go out and came back to an error on the screen which I can not remember what it is. Since then the XDA2 will not boot, only coming up with the boot screen saying "serial V1.06" and when placed in the cradle "USB V1.06"
I have followed the recovery posted from here http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=62
I got an image from a spare XDA2 and placed on a SD card but can not get it to load in to the dead XDA, it comes up with the following msg "sections=1 not allow update"
I have tried to re do the upgrade but can not talk to the XDA, have I missed a step or is there a configuration in the XDA that has changed some how....
I have also search the posts here and found problems close to mine and have tried them too, I do not know what the ROM version was before I tried to Upgrade but I do know it was older..I did check.
from what I have readed if I can get the SD card upgrade to work then I can re do the upgrade.
Any help PLZ
Thanks
Sorry I forgor to say that I have done 1 XDA already and all went well..
Sorry I forgor to say that I have done 1 XDA already and all went well..
I have the same problem.
My laptop hibernates during XDA upgrade. My XDA2 gone into bootloader mode and stops there.
I've tried link from pdamobiz - with, at least, "not allow update" screen.
any idea's ???
I have got an spv m3100. I have allready upgrade it to wm6 with your help. It has been working fine for over a year now but last knight it gave me a lot of problems so i decided to flash it again. I am tring to connect the ppc to the pc with active sync but it doesnt. I have tryed it to 3 - 4 pcs but no luck and there for i cannot flash it. I also did a hard reset it reboted install all its programs by it self but it still doesnt connect to the active sync.
Any help how to flash it from the biginig pls ??
Thanks in advance
Succeded
Sorry to bug you before guys i have succeded to flash it and its all fine all i needed it it was to connect once .
Now if its posible i want to know if there is any article to read about the battery or any soft about it
Thnks again
Mate, install Hard SPL V7 (if you haven't already ) and use the sd card method to install roms...
Go to page 116 post 1160 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
for the sd card method to install Hard SPl. To use the sd card method to install a ROM, drop the steps with sspl.exe in them - I believe its steps 5 & 6.
Make sure the sd card is 2 Gb or less, formatted FAT32 and the .nbh file is named hermimg.nbh.
Cheers...
Hi mate
Ok after i flashed in the morning it started working fine for a period of time and then it started the moves again. What it actually does is that the phone is not working the device boots ok with the programs but the phone is not working at all and if it does whene i try to make a call the whole ppc is freezing.
I have tried the hard spl that you provided and i flash it. All ok. Now the problem is that after all the reboots and the freezing to get the phone working the system crash and i tried to flash it again to wm6 the one that i had for over a year now. It reboots the ppc perfectly and i can see in the three color the hard spl ok version 2.10 but when its upgrading to wm6 it freezes to 12%
Any suggestions pls
Thnks a lot
sounds like your radio rom has been corrupted. You can try to flash the shipped stock rom but it may be a permanent brick.
To check, go to settings>system>device info. Check you have a radio rom version and protocol version. If you don't then you have a brick on your hands, sorry...
This seems to be the Achilles heel with the Hermes.
Hi again and i am really sorry to bug you
Here is what i did after trying and messing around with the softwares of the ppc i decided to check for once the hardware like you said about the ratio. I basicly took the whole phone apart to pieces and cleaned it with alcohol and a brush, dodnt know if its the right way but i have to tell you that it worked. It stop give me troble with the phone it starts perfectly and works perfectly except for sometimes that the sigla goes off witch it shoudnt. With the hard spl that you provided it looks a little bit faster too and i am very gradefull.
The thing that remains is that from day one that the problem started the battery witch is new it ends really quick. two days ago before the problem it could last for 2-3 days but now it last bearly for one .
Any suggestions on this?
Thanks for your time.
Just remember that 3G uses a LOT of battery power when in an area that isn't very good for it.
If you flashed a new rom that is using 3G (also check which radio you should be using) and you were using the GSM network before, it could be this that is the problem.
I myself am finding that the battery is going REALLY fast at the moment as I'm working in an area with bad reception. The radio has to work harder to keep signal strength so the battery is consumed fast.
Cheers...
hey guys i'm in the middle of russia at the moment on holidays seeing some family and ive decided to give my old hermes to my uncle however he doesnt understand english so i;ve been trying to put a stock russian rom on (one i found on xda wiki) as i have a cooked rom on there it wont let me downgrade now i know theres a different approach to stock roms than cooked roms but ive never tempered with them always put cooked roms on my hermes, diamond, and my current phone the HD. The internet is ridiculously slow with its 2g connection. so i've tried searching buts its taking me hours as opposed to 10 minuets.
info that might help.
i'm using vista (english) as opposed to xp or windows 7 that i usually use to do this.
the rom on there at the moment is "yahr" by marpelo
radio 1.54.30.10
any help would be appreciated i'm sure its simple fix.
note the rom is playing up at the moment and sometimes tends to loose connection when in tri colour screen, now it culd be due to me using the wrong approach or the phones playing up.
again thanks for the help
Install Hard SPL V7 then use sd card method to flash rom.
Just make sure sd card is smaller than 2Gb. You can also flash Hard SPL this way. Go to the Hard SPL thread at the top of the upgrading list of posts...
Cheers...
thanks bud i will give it a go will let you know how it goes. i'm gonna try with out the sd card as i dont have one and have to buy one from "a bigger town" i told you middle of no where lol.
so i tired running it through a usb connection to no success as it drops connection when in bootloader. tried of a memory card it flashes a split second loading rom screen after the bootloader and its long enough to see no image found and returns to bootloader. i've tried renaming the file as per wiki xda instructions. at a complete loss. any ideas? let me know if theres any more info you need. Thank you great minds of xda.
Hello there,
first of all I tried searching for the topic I want but can't find anything similar to it. Anyhow, I am a new user and I bought the HTC Desire V just yesterday. It came with Android 4.0.3 but apparently there is an update which is 8 MB big. It's stock firmware, nothing rooted or anything. I try to update my system, it downloads, everything goes fine, it reaches the installing part. It goes till 1/2 of installation then gives me some weird red triangle icon with an exclamation mark on it (!) and then restarts, doesn't update. May I know the cause & solution to this? I am not ready to do any risky stuff with it since I have this phone temporarily only.
Thanks
P.S I am not sure whether it's a firmware update or just a security update because its size (8 mb) doesn't seem to be a firmware update... Anyway, please help me
The same happen to me also.Its a kernal. Is your phone rooted?
Sent from my One V using xda app-developers app