I installed SpecialEditionROM, however, it was unsuccessful. May be because my ROM Version is A.20.17 ENG. Now, my Siemens SX56 shows the "upgrading" message. I tried cold and hard reboot but it still shows "updgrading" message. How will I fix my phone and unlock it as well? Can sombody help me?
Hernz
Related
Hi everyone
I'm new to this message board and need some help I hope some one can help. Ok here goes I have today tried flashinng the ROM on the SPV M1000 which is the same phone as an XDAII just orange branded.. when I went to teh orange site and downloaded the rom update v3.66.1.230 and followed the instructions and got the following error message ERROR 120 : COUNTRY ID ERROR 0-0-4-4-4 and the phone / Pda is constantly stuck on and on the screen of the phone it reads Serial on the top of the screen and v1.06 at the bottom.
can anyone please tell me how to fix this problem. I'm not very technically minded when it comes to these things so instructions in laymans terms would be greatly appreciated.
Thanks to every one in advance.
[email protected]
m1000
the unit is stuck in what is known as bootloader mode.
Did download the rom that matches your contry of origin, ie uk for uk phones.
I flash these units all the time at work and dont have a problem.
You can sometimes get the phone out of bootloader by re-running the upgrade. Try downloading it again and running it.
After flashing my XDA2 to WM5 3.5a, i've tried merging storage & extended rom to gain memory by following a thread on Airfagev. After doing a hard reset, i found out that my phone is not responding and all i can see are black horizontal lines on the screen w/out backlight. I tried soft resetting it but still it stays the same.
Though i can still put it on bootloader mode, it also wont finish reflashing and an error message appears that goes like this:
ERROR 100: Model ID Error
The ROM image you are trying to use is not designed to work with your Pocket PC.
Is there any way for me to fix this problem? I really need help from anybody who's knowledgeable enough in solving this problem coz' i am new in this field.
Pls. help.
Thanks in advance!
Yoo can use NOID utility for flashing
HimaUpgradeUt_noID.exe
bootloader
Thank you. I can now reflash my device to WM2003 but not to WM5.I think it's because of the bootloader which is v 1.06.Is there any way to change this to v 1.03?
Help pls.
Hi all, first of all I am no geek, I would like to unlock my HTC TYTN so that I may use other sims while abroad etc. I have read the instructions, downloaded v£a of the Sim Cid unlocker, however every time I run the unlocker my phone shuts down and reboots. I have tried with the phone without sim with none network sim with Orange sim same result phone shutys down and reboots. I have tried waiting till it is connected via active sync after rebooting but it nust keeps rebooting. I have even manually loaded the hard spl and run it on the phone but my phone shuts reboots and the spl has not been updated. Can anyone tell me what I am doing wrong?.
Thanks in advance Jimmy
info on device status tytn on orange
I have kept trying but still the phone keeps rebooting everytime I try to unlock. Device status uis as follows
operator version 24.181.1.612
ROM version 1.81.61.2 WWE
ROM Date 09/20/07
Radio version 1.27.12.29
Protocol version 22.45.88.07W
does any of this indicate I would have a problem using current unlock version 3a?.
Thanks in advance Jimmy
Check to see if the SPL has changed... Go to bootloader - hold power, OK above flywheel and reset with stylus. hold until tri-colour screen comes up. It will tell you your IPL and SPL.
It may already have flashed and that means you can update your rom with more safety.
Do you get any errors when running the pc? For instance [error 260](pretty common).
If that error keeps coming up you need to COMPLETELY remove activesync and then reload. All sync relationships MUST be deleted too. That fixed mine
Cheers...
Hi, first time i have ever had a problem with a Hermes device.
I have a Vodafone VPA version, and i have flashed "Schap's 4.31" WM6 PRO fine, like i have on many other devices in the past.
It is actualy a phone i was just sent back from someone on eBay because there was no network signal on any sim provider at all. I had unlocked it before i sent it but he has obviously done somthing to it.
So now, i can re-flash the rom fine, but i can not CID unlock it at all.
It gets to that point and give me the ERROR [262] message.
I am using "v3a by pof" to do the CID unlocking.
I have looked at the device infomation (as i can go on to windows just fine) and i do not have an IMEI number or a Radio version or a Protocol versioni number.
I think i basicaly need a Radio Rom upgrade/flash to fix it? But i can not seem to do it.
Is it somthing to do with bad blocks?....
I am dual booting Vista & XP from my laptop and have tried on both OS.
Any help would be amazing.
Update:
It also show "NO GSM" on boot along with the SPL info.
It also has HardSPL & flashing from memory card is freezing at the GSM stage also.
Why wont it let me flash a Radio to it? Its driving me crazy!
I am poor in english, so hope you can understand what I say.
Your hermes is likely the hardware is broken, I suggest you get it repaird.
My hermes like you just before the issue of "NO GSM", but I am so poor in english, I am
sorry!!!
Hmmm, that is a possibility.
But i have seem many people with the same issue and have been able to fix it.
I have been trying to wipe some settings using MTTY.exe
However, where is should be saying USB>
It is saying CMD>
I have looked through the wiki but still no luck.
Anyone else know how to fix this?
I want to help someone on this please , bcs HTC SPV M3100 when i'm trying to switch on phone was stuck on HTC logo and nothing more , i have try to put on boatloader mode and phone was going on bootloader mode three color screen and show this:
HERM100
IPL-1.04
HERM100
SPL-2.03
i'm trying with hard spl from Pof soft but error getting.
Can someone find a time to help me?
hallooo
experts please!
Hello haveri,
what ROM are you trying to start? I was stuck on HTC logo too, when I tried to start a ROM without installing Striped ROM first, which was highly needed. So I done hard reset(three color screen), and flashed again.
For starters, put in bootloader, connect to PC (1st untick "Allow USB Connections" in activesync) and run Hard SPL V7. Install it on your Herms and hope it works because otherwise you are in for a whole heap of hairpulling frustration...
If you get Hard SPL onto your Hermes then use the sd card method to flash a new rom...
You could have avoided this by doing a little research instead of going full pelt into flashing, you Hard SPL BEFORE you get into trouble, NOT AFTER....
Hi guys,
I have a similar problem with a T-Mobile branded TyTn from a friend of mine who thought flashing ROMs without putting device into HardSPL would be clever.
The devices has also IPL-1.04 and SPL-2.03 and from the bootscreen it looks like WM5 should have been installed. I also get the "NO GSM" message and I REALLY tried every fking method but without success.
I even created a Goldcard (and verified on another device it's working, level 0 instead FF) and tried to flash several ROMs (also Cingular WM5 ROM and original german T-Mobile ROM) but no luck.
I also tried to run HardSPL V7 but as far as I remember it just said it cannot connect.
Funny thing: HardSPL V9 DOES start flashing and on the PDA and the PC the bar shows 100% but some moments later it says "Could not update" (or something like that).
I even tried different mtty methods from several posts from the forum (erasing the NAND on different ways, qtek loader method with erasing the first blocks) but I'm really really frustrated now and I believe there is no solution here?! (device has no guarentee)
So, if someone has ANY hint or useful information write it down or send me a PM.
I gladly appreciate your help and hope for a solution!
Cheers
P.S.: I couldn't find any information saying Goldcard method works (or even exists) for Hermes. Can someone confirm it does really work?