Related
This message contains all postings in this thread
dated before January 19th 2003
Subject: memory problems
From: max
Date: 17 Jan, 2003 22:41:01
i can't delete mij files in my document it's say's when i will
delecte the file ( MP3 file) cannot delete "filename" acces
denied make sure the disk is not full or write protected and the
file is not currently in use.
i've closed all mij programs in the memory menu butt it will not
move
what can i do
max
Subject: check
From: spikomatic
Date: 18 Jan, 2003 03:41:10
i have same messages often..
i have not the best resolution..soft reset! then delete the file
:-]
maybe it isnt able to delet cause u made a playlist?i dont know?
anybody?
so all i can say..soft reset then delete...
peae
First of all .. my thanks goes to all the people to this forum!
You're really GREAT !!
In any case sorry for my poor english :wink:
I've few questions ...
I've read many many pages but I can't understand the right procedure to follow for dumping my Himalaya original ROMs because in some pages the "d2s" command is followed by some numbers and in other, by other numbers ... confusion bring me !
After that, otherwise, I've tried to follow the XDA II procedure and the storing procedure to SD seems to be ok .. but when I try to save the rom dump from my SD to PC using ntwr (otherwise was unreadable in Win), I've got a read error but, in any case, I obtain only one file on my PC of about 400 MB and I suppose that something is wrong because all of you speaks of about 50 MB ... so ... What's the right procedure with the right command? How can I be sure that my dump is correct? The dump it's only one file or one for separate ROM Radio and Extended?
When I solve this issue I can try to upgrade my Himalaya to WM2005.
Thank you for your help.
Please help me, I'd like don't lose my guarantee.
This post was submitted also to buzz forum
Now this is the situation ...
Qtek 2020 - 1.66.04ITA
-= Preparing the device =-
01 ) I,m gone to Bootloader (Power + Directions + Reset)
02 ) I see on the device "Serial v1.06"
03 ) I stop MSSync service Ctrl+Alt+Canc and stop wcescomm.exe
04 ) Put device on cradle
05 ) Now I see on the device "USB v1.06" instead of "Serial v1.06"
06 ) Put the 512 MB SD into the device
07 ) Start Mtty 1.42
08 ) Leave as is all the parameters
09 ) I've "USB" port (and not ".WCEUSBSH001") and I press USB
10 ) Ok seems to be connected to the device
-= Dumping the ROM on SD =-
11 ) Into mtty command line I write (and not copy and paste and without "sd a" at the end)
d2s 80000000 02000000
12 ) Device tell me % of work while in mtty I found
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SD : Detected one card
SD : ready for transfer OK
pc->drive.total_lba=EEC00
pc->drive.num_heads=0
pc->drive.sec_p_track=0
pc->drive.num_cylinders=0
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=B368
pc->drive.drv_type=40000000
pc->drive.securedAreaSize=0
pc->drive.securityDrv=0
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=1DD80000
SDCARDD2S+,cStoragePlatformTyp e=FF
****************************** ****************************** ****************************** ****************************** ********
Store image to SD/MMC card successful.
USB>
13 ) Then I write
d2s 60000000 00300000 sd a
14 ) Device tell me % of work while in mtty I found
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SD : Detected one card
SD : ready for transfer OK
pc->drive.total_lba=EEC00
pc->drive.num_heads=0
pc->drive.sec_p_track=0
pc->drive.num_cylinders=0
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=B368
pc->drive.drv_type=40000000
pc->drive.securedAreaSize=0
pc->drive.securityDrv=0
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=1DD80000
************
Store image to SD/MMC card successful.
USB>
15 ) Then I write
d2s 70000000 01080000 sd a
16 ) Device tell me % of work while in mtty I found
SD:Waiting for card insert.........
CMD3 for SD, it's OK, ready to get RCA from response.
SD : Detected one card
SD : ready for transfer OK
pc->drive.total_lba=EEC00
pc->drive.num_heads=0
pc->drive.sec_p_track=0
pc->drive.num_cylinders=0
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=B368
pc->drive.drv_type=40000000
pc->drive.securedAreaSize=0
pc->drive.securityDrv=0
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=1DD80000
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=EA0000
All:dwSize=1F20000
****************************** ****************************** ******
Store image to SD/MMC card successful.
USB>
-= Saving ROM from SD Card to PC =-
17 ) Put the SD Card into a Card Reader
18 ) Go to Dos command line into ntrw path
19 ) Type "ntrw read ROM.nb1 H:" where H: is the Card reader drive
Now start the problem ... :shock:
I want to know if it's all ok with this process ...
The output of ntrw is:
NTRW 2.0
Removable media
Cylinders: 0:60
TracksperCylinder: 255
SectorsPerTrack: 63
BytePerSectors: 512
bufsize is 65536
500629504 bytes written bytes: 0
ReadFile(): ROM.nb1 -- Parametro non corretto
First signal of some error but someone tell that's ok!
And then I see prompt.
Now I find the file ROM.nb1 that is 477 MB (like the SD size after a FAT format).
It's ok? ... I don't think so .. but let's going on!
I open the file with an HEX Editor and the file seems ok but after a string like HTCE the file contains all 00h.
Can I cut off that part?
How can I ensure myself that's all ok?
Come on guru don't leave me with the bootloader splash screen instead of the MAGNETO one :lol: :lol: :lol:
Thanks to rhmartin's help (on buzzdev.net) I've reach this situation ..
I've got my dumped rom in SD and in a file.
But ...
I acquire more information about my Qtek 2020 (XDA2):
ROM: 1.66.04ITA
Radio: 1.10
ExtROM: 1.66.148
I think that's a WM2003 (not SE), isn't it?
In any case ... I put back my dumped roms in SD and followed the procedure for rom restore:
1 - Bootloader
2 - Put SD into device
3 - Wait for "Press Power Button"
4 - ecc. ecc.
But I never reached number 3, what's wrong?
I've put back the dump as a single file (as ntrw output give to me), it's correct or I must put it back (and so backup first in that way) as 3 separate files?
I've seen that in download area there's no WM2003 dumped rom, so I search by myself and I found RUU172128ITA (1.72 ITA) but I prefer if my backup can be useful for disaster recovery and can be used for my original version backup.
I think that you understand my situation .. I prefer ask before a not funny situation instead fill the forum with hundreds emergency posts.
I hope you think I've reason.
Thank you for the patience and sorry for possible misunderstandings or english syntax errors!
NO ONE CAN HELP ME ... INCREDIBLE!
I'm ready to ask sorry but ...
There's no one in this great forum that can help me ...
IT'S INCREDIBLE !!! :shock: :shock: :shock:
I don't think that no one haven't my problem ...
PLEASE SOMEONE HELP ME
:evil:
What is this file ???
Is it aku 3.3 in english or russian????
-----------------------
MODERATOR EDIT:
Changed the subject, use this as the main thread to discuss HTC 2.05 WWE AKU 3.3 ROM issues.
Download and ROM details in the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_Upgrades
BE SURE TO READ THE WIKI BEFORE ASKING QUESTIONS PLEASE
English.
If you need Russian one look for it in Upload/Temp directory
It is in English, I just flashed it using 1.10mfg method
An still no MUI I presume ?
What Where Who Its New The Wwe Version?
Plz Give The Link And Why Dont You Say Anything?
bubu23 said:
What Where Who Its New The Wwe Version?
Plz Give The Link And Why Dont You Say Anything?
Click to expand...
Click to collapse
ftp://ftp.xda-developers.com/Uploads/Hermes/
Here you have.
BuT WhY TyPinG LikE ThAt ! Are YoU PaRkInsOn ?
Is it from HTC or cingular? I've heard both are about to release an AKU 3.3 rom
loll no im not parkinston maybe my keboard is
but why the file finish with test?
its not good its just test???
plz tell me im horny on that fileee(rom)
English confirmed.
Just flushed OS and Ext rom.
ROM Version:2.05.255.1
ROM Date: 01/17/07
ExtROM Version: 2.05.255.101
OS 5.1.461 (build 15671.3.3.0)
I can't get to FTP :/ what user and password ?
reg
Sar
Username = xda
Password = xda
You get to the ftp by this link no pass needed...
ftp://xda:[email protected]/Hermes/
Cheers
Seems very fast...
cant see where it says TEST though. My of been a test for the carriers, so likely the RTM for the carriers to then implement.
So far, so good... at least this one is english, unlike the Swedish update i did yesterday
in the ftp thers only the swedish rom i cant find the wwe rom??
RUU_Hermes_2.05.263.1_6275_1.34.00.10_108_SVE_HTCEUR.exe is now up... Guessing it is an official release from htc?
Cheers
Well i flashed it also.
the Test is included in the splash.bmp. =)
really... But imho the swedish one is a bit faster, but that is just subjectiv i didnt tried to test it with a benchmark program.
btw. any update from cingular?
Somethings fishy about this.
This is supposed to be AKU 3.3, but theres no WPA2 support???
not sure this is a complete ROM?
Does this mean MS Voice Command over bluetooth is fixed without the hacks?
I have detect problems with this rom! Is better wait for another!
Problems detect:
- No wpa2
- Phone connection always breaking down
- Can't go to my contacts!
- ActiveSync always says pocket is out of memory (yes I reset several times)
Flash Using Lnb
This is my first time flashing using lnb and i followed the wiki about using mtty..i just wanted an experimented persons to examine the output of mtty and tell me if the update was perfectly done and if there was no problems in nand please...
Thanks
Iverson....
USB>
USB>task 32
Level = 0
USB>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 461
Storage Total block: 475
Total Bad Block in CE: 0
NeedToEraseBlockStart: 474
Storage format success
USB>lnb 06_OS.nb
:F=06_OS.nb
:A=501A0000
:O=00000000
:L=FFFFFFFF
start NB image downloadSH
Load ADDR: 501A0000 Length: 3C0C800
*********************************************
*********************************************
*********************************************
*********************************************
*********************************************
*********LAST BLOCK, dwBytesCollected=0x13800
Code entry point at 0x53DA0000
Write Nand Success
USB>task 28
Storage format start
Write Nand Success
dwBlockToWrite = 13
Storage start block: 473
Storage Total block: 463
Total Bad Block in CE: 0
NeedToEraseBlockStart: 486
Storage format success
USB>
Fix:
- Input Types: (注音) + (倉頡) + (手寫) + (全螢幕手寫) works with no doubt
- relpllog.exe error exixts if 手寫(mboxcht.dll) is called, i dunno why, have checked so many versions from ATOM LIFE to ATOM AKU2.2....still finding. But I think 全螢幕手寫 is good enough.
- Finally I am able to change the program links in the initflashfiles.dat to unicode 16
- SMS issue: If you have SMS issue, please go to phone - options - service and check the SMS default gateway number, for HK it is +8536800852 somewhat like that, just change it to the number your operator provided.
Programs added:
- Total Commander
- Regedit
- pBar
- 1 extra IME is hidden (CHS 併音), a registry hack need to apply in order to activate this IME
Download Link: http://www.mediafire.com/?ffklanjl2gy
Missing eBoot.nbo: http://www.mediafire.com/?1xrxmtlymrz
If you do not want a CHT version WM6 but wanna have CHT input, check this: http://forum.xda-developers.com/showthread.php?t=332012
Version:
Windows Mobile 6 Professional AKU0.3.0
CE OS 5.2.1413(17913.0.3.0)
NEVER ATTEMPT TO FLASH WM6 USING SD CARD FLASHING!!!
Upgrade Procedure:
1. just extract the rar file and flash you phone in BOOT LOADER MODE!!!
Congratulations!!! Great stuff.
Anybody know whats happen with me?
Atom show
Mar 29 2006
CPLD Ver:A0060109
.
.
.
Downloading progress:100%
Usb Transfer Completed
Write Bootloader...
Please wait...
I reflash Xda-Atom-CHT-20060426-MOT0822 and its worked(Thanks God)
Goodbye WM6..
How about atom exec?
Would that be released soon as well?
help ~....
nthan said:
Anybody know whats happen with me?
Atom show
Mar 29 2006
CPLD Ver:A0060109
.
.
.
Downloading progress:100%
Usb Transfer Completed
Write Bootloader...
Please wait...
Click to expand...
Click to collapse
i faced the same problem too ~!oh my god ~! ~!~ some more i can't open my atom now ~! ? jst the screen show up update utility `!??? isn't it the rom spoil d ?~!~? help me pls ~! ........
Guys....
the rar file consists of 6 files:
- (268,288)7zr.exe
- (258,048)Device Software Update Utiltity.exe
- (65,536,012)diskimage_Ver.nb0
- (16,384,000)ExtendedROM.img
- (110,261)nova_pda_033105.mot
- (6,022,611)vl1d_pda_Ver.mot
- (524,288)eBoot.nb0 - http://www.mediafire.com/?1xrxmtlymrz
If one of these files are missing / corrupted, the upgrade / flash will failed.
Here are the size the dump screen
dcoloane said:
Guys....
the rar file consists of 6 files:
- (268,288)7zr.exe
- (258,048)Device Software Update Utiltity.exe
- (65,536,012)diskimage_Ver.nb0
- (16,384,000)ExtendedROM.img
- (110,261)nova_pda_033105.mot
- (6,022,611)vl1d_pda_Ver.mot
If one of these files are missing / corrupted, the upgrade / flash will failed.
Here are the size the dump screen
Click to expand...
Click to collapse
Hi dcoloane
It seems the CHT input doesn't compatible with the WM6 WWE version so is possible to rip the original CHT handwriting file to be cab let us try this ????
Or just translate the CHS 0.4 to CHT is much faster to solve the problem ?
dcoloane said:
Guys....
the rar file consists of 6 files:
- (268,288)7zr.exe
- (258,048)Device Software Update Utiltity.exe
- (65,536,012)diskimage_Ver.nb0
- (16,384,000)ExtendedROM.img
- (110,261)nova_pda_033105.mot
- (6,022,611)vl1d_pda_Ver.mot
If one of these files are missing / corrupted, the upgrade / flash will failed.
Here are the size the dump screen
Click to expand...
Click to collapse
i think this folder must have eboot.nb0 to completed rom-update
Missing eboot.nbo
tube216 said:
i think this folder must have eboot.nb0 to completed rom-update
Click to expand...
Click to collapse
You are correct.......................sh.......there are too many versions in my PC now and I forgot to dump a eboot.nbo to the rar file!
That's why.................thank you tube216.........
Sorry guys, mmmmissing the most important file for eBoot
http://www.mediafire.com/?1xrxmtlymrz
Hi
I am new in this site and and hope you excuse my very poor english...
But i have a probleme and i hope to solve it here with some help...
I explain my probleme:
i heve a HTC HD2 and IGO8 3-4-117940 version with a skin choup on my SD card;
It work very well ...for about 10 minutes then i have the following error message:
fatal error occured in mean thread
Exception: 0xc0000005
At address: 0x0016020c
Access violation reading address: 0x10000000
0x0016020c
WinCE CallStack snapshot (function names unknown - map file \Carte de stockage\Igo8\iGO8.map not found):
and igo crash...
so i can use it again for a few minutes but it crash again...
her my sys.txt:
[debug]
skip_eula=1
[device]
Type="ALIAS_TOUCH HD"
sdcard_dsk_num=7
[folders]
install_path="\Carte de stockage\iGO8"
mortscript="\Carte de stockage\Program Files\MortScript\MortScript.exe"
[interface]
skin="ui_igo8_da"
vga=1
maxzoom2d=6000000
show_exit=1
Skip_contact_import=1
screen_x=480
screen_y=800
[map]
rasterorder=""
viewpreset_front1="30,100,7200,10"
viewpreset_front2="70,7000,6000,10"
viewpreset_top="600,50000,225,10"
viewpreset_front3="70,7000,6000,10"
map_mode="3D"
follow_gps="1"
rotation="1775"
popup_info="1"
3d_buildings_distance="1"
3d_dem_detail="3"
[navigation]
autoreplan_action="AUTO"
[power]
powermgm_state="0"
backlight_night="78"
backlight_day="100"
[rawdisplay]
screen_x=480
screen_y=800
autoconfig=1
highres=1
class="portrait"
driver=GDI
[route]
correctness="88"
route_type="SHORT"
allow_toll="1"
[settings]
accident_recalc="0"
closed_recalc="0"
heavy_recalc="0"
congestion_recalc="0"
roadworks_recalc="0"
closures_recalc="0"
danger_recalc="0"
weather_recalc="0"
police_recalc="0"
invalid_recalc="0"
[warning]
speedcam_warning="1"
speedcam_soundtype="0"
speedlimit_warning="0"
speedwarn_tolerance="-1"
speedwarn_toltype="1"
speedwarn_alt_tolerance="-1"
speedwarn_alt_toltype="1"
[warning.driveralert.settings]
preshow_distance_cat0="500"
preshow_distance_cat1="500"
preshow_distance_cat2="500"
[switchmap]
changer="\Carte de stockage\iGO8\Extension\MapChanger\MapChanger.exe"
1=",map_ta,\Carte de stockage\iGO8,\Carte de stockage\iGO8"
2=",map_nt,\Carte de stockage\iGO8,\Carte de stockage\iGO8"
3=",map_ot,\Carte de stockage\iGO8,\Carte de stockage\iGO8"
4=",map_us,\Carte de stockage\iGO8,\Carte de stockage\iGO8"
[scheme]
disable_themechanger=1
If somebody could help me it will be great...
Hello,
did you ever try
\Storage Card\Programm Files\IGO8\content\map\.....fbl\
as storage path for the IGO Map files.
(must not be "Programm Files" you can use each other folder for it.)
I have this problem a few month ago and all what happend in my case was that the maps are not in correct folders, IGO is finding the map but after a while something went wrong and IGO crash.
Hopefully i can help you.
gr33tz
hello....and thank's for your reply...
I have create a igo8.map folder in igo8 folder...
\Carte de stockage\Igo8\iGO8.map (and i put the map.fbl in it)
but a already have the same error message...
should i do something else....??? change my sys.txt...? or create another map folder in a other place ?
Hi try reinstall you IGO but when you make new installation make sure you install program on main memory and you maps on SD Card. Good luck
Hi
I don't need to install igo8 on my phone...all the folder is on my SD card...
I just start the igo.exe and igo stard well...
Some friends have se same phone and the same igo8 version and they have no problem...!!!
krazy1 said:
Hi
I don't need to install igo8 on my phone...all the folder is on my SD card...
I just start the igo.exe and igo stard well...
Some friends have se same phone and the same igo8 version and they have no problem...!!!
Click to expand...
Click to collapse
Ask your friends to give you their data.zip and sys.txt than try it again.
Yes i will try that...thank's
krazy
i have a problem with IGO8 on my HD2. it say's that the device doesn't have tmc software and no gps module. what should i do?
cipriann1984 said:
i have a problem with IGO8 on my HD2. it say's that the device doesn't have tmc software and no gps module. what should i do?
Click to expand...
Click to collapse
get a proper sys.txt for hd2. just google it, or search here on xda.