Hi,
I have an XDA O2 (Wallaby) which I got from a friend of mine who used it without a problem in its life and now I am stuck with a flashing O2 XDA.
Let me try to best describe my problem.
I had copied some of my excel files onto the O2 and then I had a distinct feeling that it had gotten to be much much slower.I am not too sure if this is the cause.
I was not using it as a phone but one day I slipped in my SIM card so as to surf the net and it just would not connect via GPRS and after that it had become very slow hanging every once in a while so I did a soft reset but it still was slow and the GPRS would not connect neither did it detect my phone service provider.I used to surf prevously through GPRS without any problems.
Then I did a hard reset and it just wouldnt work after that it would start with the blue O2 screen and begin to flash on and off with a blank screen with a small keyboard icon in the lower right hand corner presumably the affected excel file....I think my XDA has a virus now please help me out from here.
I tried doing a hard rest and I depressed the reset button on the RHS side that's it(smaller hole bigger one for soft reset) Once I press down with the smaller end of the stylus I press it again then the blue screen with the O2 logo comes to life it stays on for sometime and then a "tink" noise comes and the busy sign comes as if it has just opened an application ..a blue small band on the top most corner and a small keyboard icon on the lower rhs hand of the screen then the screen begins to flash ten seconds apart for quite some time...infact that all it does before shutting down and restarting all over again.
Is there any other way to do a hard reset.What is the right way?? as on one of the forums said that I should depress the power button and the soft reset button at the same time for about 5 sec I tried the hard and something called the WALLABY Bootloader V5.15 came on the screen with the message 'WAIT' after a couple of nail biting seconds I got an error saying GSM ERROR the screen was a clourful white red green and blue strips....what happened??
Then I proceeded to depress the soft reset button it restarted with the usual error of a program being opened and the screen flashing..
Hope to get a reply from this forum.
Take care
Ciao
Al
flashing screen
almaal have you tried flashing with a sd card? the GSM error indicates that the radio unit is corrupt. Have you attempted to upgrade the rom? If u have was it programme A or Programme B? by the sounds of things you have. Does the power light light up? let me know the answers to this and i might be able to help
have you tried flashing with a sd card? the GSM error indicates that the radio unit is corrupt. Have you attempted to upgrade the rom? If u have was it programme A or Programme B? by the sounds of things you have. Does the power light light up? let me know the answers to this and i might be able to help
Hi,
1st off thanks for your reply....
I have downloaded Programme A to upgrade my rom but cant seem to get it loaded onto the SD card. I unzipped osimage.exe and tried to store it from my PC to SD card but cant seem to do it....furthermore I was advised by friends out here not to be a braveheart and venture to kill my XDA but still I'd like to try...you see I'm not to conservant with the software bit and I'm only a end user...
Could you give me a step by step guidance to get the software loaded to the SD card via a card reader and then flashing the rom..
Hope to hear from you....
Alvin
flashing from sd card
Firstly make sure u have winzip winrar or some other compression software on the computer then right click on the programme A exe file and click open with whatever compression program u have i use winrar so i will say open with winrar. You now need to extract all files into a folder.
Once you have done that open up OSimagetool and on source browse for the folder u just extracted the programme A to and look for nk.nbf,you will need to tell it to look for nbf files and not nb1 files , which is the default and select it,it is in the english folder. In the destination u need to select your sd card which should be in a card reader as u cant program it directly to the XDA or via the memory card, once you have done this click copy. when that is finished you need to take the card and place it in the xda and do a cold reset . A screen will appear saying SD Download click the action key on the pad to commence flashing. after a few minutes it will inform you that it has finished. remove the sd card and Cold boot again then once the wallaby has rebooted back to your bootloader screen soft reset it,ignore the gsm error now cross your fingers while you wait to see if it reboots. If it reboots ok set up activesync again and run the radio upgrade. By the Way any info on the sd card should be saved before attempting this as it will be overwritten by the osimage tool. Also only the xda can read the card , the pc will say it needs formatting Good luck
Any Luck
Did you have any luck reflashing with a new rom almaal?
I have followed the procedure. The system rebooted and I got the GSM error which I ignored and continued the process. The system rebooted properly i.e I get to see the start menu and the calendar, but the device does not get detected by activesync. Another thing to note is that the system has become terribly slow. And although the backlight is switched to on it the device keeps on flashing. What do I do now?
almaal said:
I get to see the start menu and the calendar, but the device does not get detected by activesync. Another thing to note is that the system has become terribly slow.
Click to expand...
Click to collapse
That´s quite normal on a device with the gsm error.....
Stefan
wallaby xda flashing
format the sd card then and copy the radio upgrade over to the card. not as an exe file almaal, right click it again then extract files and copy the files over , if u have a cab file including then just use file explorer on the xda to navigate to the storage card and click on it and it will install. If not then click on the rsupgrade.exe. Hope you have more luck with this than i have i had . Good luck
wallaby xda flashing
format the sd card then and copy the radio upgrade over to the card. not as an exe file almaal, right click it again then extract files and copy the files over , if u have a cab file including then just use file explorer on the xda to navigate to the storage card and click on it and it will install. If not then click on the rsupgrade.exe. Hope you have more luck with this than i have i had . Good luck
Not charging I think
Hi I dont know what to make of it but now my wallaby came to life with the rom that I flashed but it seems to have gone crazy. Let me best try and explain.
1) The green charge light does not come on when I put it onto the cradle or plug it directly for a charge.
2) It does not make any sound, no beeps no nothing....but when an mp3 is put on it plays
3)The back light does not come on which is enabled but does not work I have to work with a dark screen...is there a brightness control which can be adjusted...its like its on power save mode or something..
Now its back flashing the O2 screen again its become terribly slow and unstable and I have to do a constant reset. How do I know which is my ROM to flash, I've flashed the R.30.07 ENG Rogers (4700 kB available) from http://www.romkitchen.de/WM2003/form.php.
I somehow feel that my O2 is not charging
Can you make any sense of this ..
Alvin
Hi
And another thing is that I trird copying the radio upgrade over to the card and then clicking on rsupgrade.exe. The upgrade fails at 1% giving an error as follows:
Flash Failed!
Press ok to restart your device.
What could be the problem? and how can I fix it?
Thanks
See http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError
Regards,
Neil.
Flash Failed
Neilius you have obviously not been through this process, no offence, but as i have tried to ask with a few posts on here it seems when the radio upgrade fails the wallaby refuses to charge. Which i think is the reason the radio upgrade always fails at 1%. Unfortunately nobodys knows or is even interested in finding out why
Flash Failed
Neilius you have obviously not been through this process, no offence, but as i have tried to ask with a few posts on here it seems when the radio upgrade fails the wallaby refuses to charge. Which i think is the reason the radio upgrade always fails at 1%. Unfortunately nobodys knows or is even interested in finding out why
No Charge no back light
Hi,
I have flkashed my rom but I cant get the RSU upgrade done.Now I have a running O2 with no backlight and it does not charge....where do I go from here....please reply my life is a meess without my O2 is it time for a change...howz the O2 mini or the imate JAmin fed up with this GSM error.
Alvin
Related
Hi
Started program - found SX56. Message "Upgrading - will take about 5 minutes"
on pda. Then it said that it had a problem with the USB or COM connection, and
to fix it in device manager. I opened Device Manager, and checked that all the
USB and COM ports were enabled, which they were.
By this time, the unlock software and ActiveSync had stopped running. The pda
was still stuck on the "Upgrading - will take about 5 minutes" screen. Since
the configuration has changed, ActiveSync will no longer recognize the device,
and will not sync with it. Your software will not connect until ActiveSync does.
All that comes up is the "Upgrading - will take about 5 minutes" screen. there
is no other functionality to the system.Hard or soft resets make no difference.
Active Sync doesn't work. The PDA has changed its configuration, so active
Sync doesn't recognize it. When I plug it in, Active Sync sees something, but
can't even tell that it is a pda, and I can't even set up a new connection with
it. let alone use the old connection.
Can anyone help? is there a way i can reinstall active sync or is there another way to fix it? please help
You will need xdatools, sd card, card reader/writer and rom file from kitchen for sd card flashing. Unzip the rom after download, start xdatools on your pc, choose the unzipped rom file as source and the drive letter for your sd card as destination from drop down menu, once the card is programmed insert sd card to phone, push reset while holding power, when prompted you then push the action key which is centre of 4 way rocker buttons. Once flashed push the unscrewed stylus into hole next to headphone socket, push once only, wait one minute push once more, this will work as long as you dont have a problematic version of bootloader on your phone. Good luck.
System is entirely backed up onto SD card.Can't use SD card. Can't use PDA.
PDA is still stuck on "ugrading - will take about 5 minutes". It apparently has
no operating system in ROM. No difference with hard or soft reset - comes back
to same screen, no function in PDA.
HELP PLEASE
I think you misunderstood, a normal backup is no good, you need to program an sd card with a new rom, when this is placed in your xda and soft reset it should reprogram your phone with a new rom. You are correct when you say it has no rom, the method I described should restore your phone to a working machine. You do not need a rom to reprogram using bootloader/sd card method, try it and see.
You will need xdatools, sd card, card reader/writer and rom file from kitchen for sd card flashing.
Click to expand...
Click to collapse
Okay, so can I basically use the newest ROM which also unlock the device too?
You will need to use either xda developers special edition rom to unlock or include the unlock program from the kitchen in a 2002 rom, you can then upgrade to wm2003 if you wish, you cannot unlock under wm2003 so you must use special edition or kitchen rom based on 2002 first.
I am sorry if i keep asking you questions.
I do have the xda special rom, ive tryed using it but it caused the problem i do have right now.
i did download xdatools by jeff. i cannot run them though.
Could you describe step by stef of what i need to do.
i.e. do i need a complete NEW ROM, or can i just transfer the xda special rom to my SD card and then run it to restore my device?
But i guess not, else you wouldnt have explained what i need to do.
Thats the error i get when i try to run xdatools. (I dont understand the install note)
"INSTALLATION
From the source + exe distribution copy OsImageTool.exe and itsutils.dll
to the programme A directory as created by unpacking
jeff's-exe (http://cuba.calyx.nl/~jsummers/XDA/) to a directory in
your "Program Files" directory. Then run 'OsImageTool --register'."
IF you unzip the files you already have both of those files in the folder.
THANKS FOR YOUR HELP
You have to install ActiveSync.
You can get it diretcly from Microsoft for free....
HTH
Stefan
. I was able to locate the NK.nbf file. I ran the XDA OS image tool, to put the OS on the sd card, from the NK file. That apparently succeeded, but it is hard to tell. After loading the OS, when I take out the sd card, then put the sd card back into the sd card reader, it can no longer read the sd card. I can format the sd card again, using my camera, so the sd card is not destroyed.
Wher I put the sd card in the SX56, there is no problem, but there is no success.
Pushing soft reset alone does nothing. Pushing the power button alone does not turn the machine on or off, and does nothing.
Pushing power and soft reset at the same time, gets me the “Wallaby Bootloader V5.15” screen. It first says “wait”, and then says “GSM OK”. It then does nothing else, and doesn’t prompt me to do anything else. If I push the action button, I get “DIAGNOSTICS GPRSA 20324e4”. From there, I can scroll up and down, and test the RAM, Display, battery, USB, etc – all items tested seem OK. There is nowhere to go from here – all it does is test the pieces.
After that, if I push the hard reset (the one that disconnects the battery), the power goes off, and the screen is dark. This is the only way to turn the machine off at the moment. If I push hard reset again, it comes up with a screen full of lines, with two blank holes in it (see attached file). From there, none of the buttons do anything, except hard reset (which turns the machine off again), or soft reset + power, which brings up the bootloader screen again.
have the siemens ROM. It will not work with the cradle, because it cannot find the pda if Activesync can’t make a connection, and loading it onto the SD card does nothing new – both results are exactly the same as with what described above.
any suggestions?
Hi, I already read a lot in the forum and the wiki, but as my first try to update my rom went terribly wrong I tend to ask some pros for help
I got me a used XDA1, it worked fine and was a german O2 Model. Then I got the last Update from O2 (3.19) and updated it with success. Then I wanted to unlock it with your Special Edition Rom, downloaded it and tried to apply it just like the O2 one via active sync and progam A. Result was, that my xda got stuck, now I can only see the empty transfer bar on the xda and can´t connect to the xda with active sync anymore. Both resets won´t help to bring the xda back to live the silly bar comes back every time... I can still get into the bootloader, though. As far as I understand I can still get the thing working again with a SD-Card and a rom on it? Can someone pleasepleaseplease tell me which card to buy (I don´t have one jet...) and how to get a onto this card and where I can get this rom? I still have the Files this O2 exe unzipped onto my disk and theres a nice 31MB NK.nbf in the Program/German folder. I already found the description how to flash from a SD-card with the bootloader, I just don´t know where to find the right rom and how to put it on a card... And maybemaybe, could someone tell me the right way to get this O2 xda working with a D1 card without getting it stuck again???
Thanks a lot to all your answers, I really need this thing to work again, and still ask myself how I could try to update the rom without reading enough, seems I will cry into my pillow till it works again cause it´s the only cell I got at the moment
Download xdatools and install, choose the nbf file as source and your card reader/writer as destination, choose this from the drop down menu at the bottom. You will need a 64 meg minimum sd card, a card reader/writer, xdatools and the nbf file. Once xdatools has programmed the sd card you insert into xda, push reset while holding power, when prompted push the action key which is the centre of the 4 way rocker switch. You will find many roms in the the kitchen that is kindly run my lumpistefan. Make sure to choose sd card flashing at base of screen before cooking rom. Here is the link for the rom kitchen.
http://lumpistefan.dyndns.org/
thanks a lot for the fast answer I got all the progs and the original 3.19 german o2 rom from rom kitchen. Now I´ll just have to get me a SD-Card... One more little question. I can´t turn the XDA off with the powerswitch and after reseting it also turns on automatically. I´ll have to wait till Monday to buy a SD-Card, so is there a way to get the thing off although it is still in transfermode or will I have to leave it on and in the cradle?
If you want it switched off completely, just poke once into the hole under the headphone socket, this will completely disconnect the battery, when you want it back on just push once again. Always do that procedure after flashing a rom also, push once then leave for on eminute, push once more to switch back on with new rom and noot sequence.
works fine, thanks
Hi,
I think I have killed my XDA. I was unable to charge my O2 XDA but otherwise it was working ok. I pulled tha back off and changed the battery but still it would not charge. i then dismantled it further and noticed that the small fuse near the connector was open circuted. i thought about bridging the fuse to see if it would work. I haven't done that yet, but when i put it back together nothing works at all. The screen is completely blank and when i push any of the resets nothing happens at all. This has only happened since dismantling. I have sinced checked all the connectors. Everything looks ok but still i get no response.
I have a bit of experience with electronic repairs but can't work out what has happened here.
Any help would be appreciated. Has anyone else had a simmilar problem?
Dale.
You have to hard reset. I have this problem. I click hard reset. Now Xda is working.
I have similar problem, or even worse.
I have a dead XDA. My boss gave it to me to fix it last wek. When i try to hard reset. There's a colourful image on my XDA1 that said wallaby bootloader V.522.
There's a quite big font on the left down the screen that says "WAIT"
Then there's a message GSM ERROR.
Then my Xda1 goes dead, again.
What should i do ?
You could try this:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError
Stefan
Thanks, im working on it. But the link to the both RSU are broken.
I need RSU for PW10A. And how to make ROM file ? I try to cook from the http://www.romkitchen.de/WM2003/form.php
Thanks a ot
Links are working. For downloading check this site:
http://wiki.xda-developers.com/index.php?pagename=BA_FTP_Site
Stefan
There's something supid about me, indeed.
when i flashROM via Sd card ... here is what i did :
Cook the ROM then name it as Nk.nb1 file
Run osimagetool
Select Nk.nb1 from the Source drop down menu.
Select SD card (disk drive) from Destination the drop down menu.
Select Copy to start writing process and the tool should start writing to the card.
When XDATools has finished writing the image (no Infomessage) put the SD-card into the device
Soft reset the XDA, but the XDA1 still hang and the SD card inside is not recognized (the screen is frozen at white display and the keyboard icon on the right bottom)
Hold the power button and soft reset.
The display shows the bootloader menu V5.22 and then stops at GSM error message
Press the left upright button (contacts button). Theres menu that says
flash tools
===========
ce rom to SD
boot to SD
ce + boot to SD
gsm rom to SD
ce = gsm to SD
I chose one of the options, then ...VOILA !! my SD card is formatted... LoL
Need yout advis... where I went wrong.
Thx
What for SD-Card writer are you using? Looks like you have problems writing the ROM-Image to your card. Otherwise it should detect the ROM for downloading to your device by itself. You can confirm this by entering bootloader and backing up your existing ROM to SD-Card. Then reenter bootloader, now you should be able to flash Yor Rom....
STefan
ok my phone is HTC 8525, with WM 6.1 professional . It worked fine for 3 days then it start freezing , before it does that a blue background will appeare ,then it will not let me do anything at all . When I try to touch an icon, it will say something like invalid location or could not find target . I have to hard reset it. sometimes I have to reset it 4 or 5 times a day . , In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ? please help me I truly appricat it . In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ?
Hmmm, "the mini card will freeze the whole phone"??? Are you referring to the SD Storage Card? Do you have any volatile data stored on the card? Any Today Screen Applications?
If this is the case, try shutting off the phone and removing the card. Then place the card into a card reader, and plug it into your PC. Make a folder on the desktop of your PC, and COPY all the contents of the SD card to the folder.
Now, reformat the SD card in your PC, as FAT32, and default for all characteristics.
Once reformatted, copy all that stuff back onto the SD card from the temp folder on your desktop, making sure everything is returned to it's original locations. Pop the SD card back into your phone and see if it's fixed. Sometimes, corrupted space on the SD card will make the phone behave very badly. Hopefully, this procedure might fix it for you.
-pvs
Yes Sir, i apaologize , i was refering to the SD card . i am just tierd resetting the phone every 4 hrs . do you recomend any shops that can fix the soft -ware . i notices when i start the phone and i go to clean tmp it will say" 8 Fils and 4 folders of 656 Bytes cleard ! . then 5 hrs later the blue screen comes back
After doing what pvs said, and if you still have problems I'd check for bad blocks with MTTY... I would also ,after confirming no bad blocks, would flash a stock rom then reflash wm 6.1 and see if that helps... Cheers...
Wow , how to do all that if you dont mind me asking , actually i took the SD card out i am not in need for it at the moment . can you please help me to do what you said and i truly appreciat it , Great thanks for both of you gents
pvs already says what to do in his previous post...
To check for bad blocks follow this : http://forum.xda-developers.com/showthread.php?t=377389
To Flash a stock rom you need to know what carrier the phone was on. Download the wm6 update from their site and, Making sure you have Hard SPLed your phone, I suggest flashing via the sd card method. Its safer than flashing through pc.
Format sd card fat32. copy .nbh file of the stock rom (you may have to search for it) onto the sd card and rename to "hermimg.nbh". Put back in hermes and reset to bootloader (power button, OK button above flywheel and soft reset with stylus. Hold all buttons until it goes to tri-colour screen). It should recognise the os flash and load up a screen showing 1st boot screen, 2nd boot screen, gsm And os (or something like that as cooked roms don't generally have the gsm part). MAKE SURE YOU HAVE AT LEAST 50% BATTERY!!!!! Follow the prompts... I generally use the sd card method to flash ALL my roms so I don't have problems like usb disconnecting or pc rebooting/hanging or power failures.
Hope this helps you out, Cheers...
BASELABBAS ... Please describe what you are doing when you say that you are "HARD-RESETTING" several times a day. Are you:
1) poking the stylus into the hole at the base of the unit?
- or -
2) holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]?
If you are doing the first ... this is called a SOFT reset. The second is a HARD-RESET, and will wipe the phone clean of ANYTHING outside of what came with the ROM itself.
Since you have posted that you already removed the SD Card from the device, and can (for the time-being) live without it, I recommend you do an ACTUAL Hard Reset (backup anything you need to keep first) via step #2 above, and then be patient about installing any apps. I wouldn't do anything more than sync it up via ActiveSync with your contacts for the first few of days. If things start to go crazy without any third-party apps installed, then I would look into the steps that ultramag69 has suggested ... starting with a flash to a stock ROM.
WM6.1 has been a bit shaky on our Hermes thus far. Some people are getting good results, but a lot of others are having issues like you are describing. I would suspect that your ROM might not be a good match, before I'd suspect bad blocks at this point (and it's a bit easier to test for).
If the stock rom does better on your device, you can try flashing back up to a WM6.1 ROM after that. And if you haven't already, make sure that you have installed HARDSPL before doing any of this stuff.
Good luck,
-pvs
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]. I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
it looks like i need to update
this what is say
From :
Image Version : TNT.19199
to
image version 2.05.255.1
BASELABBAS said:
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR].
Click to expand...
Click to collapse
OK, well that's definitely a Hard Reset. So your WM6.1 Rom is acting flaky right aftwerwards, eh? I would say it's time to try a different ROM, as we've been discussing above.
BASELABBAS said:
I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
Click to expand...
Click to collapse
No ... try Hard-SPL-V7.zip found at the bottom of THIS PAGE. I THINK you can flash it via the SD method if ActiveSync isn't working for you (if not, somebody please correct me). To do this, open the downloaded ZipFile with WinZip or WinRAR and copy the file inside named RUU_signed.nbh to your desktop. Rename it HERMIMG.NBH, and copy it to the root of your freshly reformatted (FAT32) Storage Card. Put the Storage Card into your device and press the side OK button and the power button simultaneously while resetting with the stylus until the tri-color screen appears and turns white. The device will find the HERMIMG.NBH file and offer to upgrade by pressing the Power Key. This will install HardSPL onto your device without the need for ActiveSync. You can also flash ROMs in this manner.
Again, good luck,
-pvs
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
ultramag69 said:
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
Click to expand...
Click to collapse
Thanks for checking me on that, Ultramag. I had a feeling there was something I was forgetting.
-pvs
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
okay first of all, if your using windows 7 then you dont need activesync. You need "Windows Media Device Centre"
Also, try turning on the phone whilst holding the volume down button. That should take you to bootloader. (3 colour screen).
You should see the word "serial" at the bottom of the screen.
Connect via USB and wait for the drivers to install.
The word "Serial" should then change to "USB".
Then you can flash a ROM via USB. If your phone is network branded then you will need to flash the correct ROM from the HTC site.
czarinio said:
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
Click to expand...
Click to collapse
You need to take that official ROM, rename it from .exe to .zip, and extract the LEOIMG.nbh file. Place this file in the root directory of your SD card and then go into bootloader like before. This will flash the stock ROM onto your device. Make sure the SD card is fairly low capacity, 2 or 4 GB seems to work best, and formatted for fat32.
Good luck!
czarinio said:
Hi, I will describe your problem in a new topic, because I see that it is broader.
Well, on Friday I bought a HTC HD2 wgranym WM 7 Unfortunately, this system will not even suitable to use, so I decided to upload, and in fact you go back to WM 6.5. I found the forum two ways by dropping LEOIMG.nbh file directly to memory card and a second by installing ROM when connected to a PC.
I bought a memory card reader and format the card. I threw the downloaded file from here: Multiupload.com - upload your files to multiple file hosting sites! Do not give it any more with this phone .... Charter installed a phone and pressing the handset, which is used to activate the phone and the VOL DOWN I switched to a mode. First there was a color screen with the specified data to HD2, but then came the white screen that says "loading ..." and nothing happened for an hour. Perhaps this file does not match my HD2, or he do not know.
The second method seemed to me an alternative and downloaded from the official HTC ROM, giving the serial number. Was surprised that it was a ROM for Norway. I do not know well past the phone, so I do not exclude the possibility that the phone is from Norway. I downloaded the ROM, I downloaded the ActiveSync. But I do not know why when you plug the phone activesync can not connect with them. He writes the message "The device was not detected. " I wanted to try and install without ActiveSync, but the installation failed.
I have no strength, like I'm doing everything ok, but I can not fix this for anything WM 7
Sorry for language errors, I used google translate to translate.
Any help thanks in advance.
Click to expand...
Click to collapse
The easiest way to reflash is using SD Card method.
If you dont have HSPL installed, you should only use this SD Card method to flash the Correct Stock ROM.
Download your correct stock ROM (you must be sure about this, in order to avoid failure). Ectract the downloaded correct stock ROM using 7zip or Winrar. Find the file named: RUU_signed.nbh and rename it to : leoimg.nbh. Place/copy that file to the root directory of your micro sd card (using card reader). For better result, before doing that, you may format your sd card to FAT 32, and copy only that file for flashing purposes only.
Now, put your sd card back to the phone. Go into bootloader mode (by pressing volume down and power on buttons at the same time). Follow the onscreen instruction. Dont forget, to charge your batter before flashing.
goodluck
Thank you all for your responses. I still have one request to you. The set did not get the CD with drivers for HD2. Has anyone can link to them? Thank you in advance.
czarinio said:
Thank you all for your responses. I still have one request to you. The set did not get the CD with drivers for HD2. Has anyone can link to them? Thank you in advance.
Click to expand...
Click to collapse
The Windows Mobile Devive Center has the drivers for the HD2 in it. So when you download the program and install it to your computer you have the drivers. Go to microsoft.com/getstarted to get the WMDC program.