hi i want some suggestions to buy a case in which i can fit the cingualr 8525 with the extended battery ?
seems like no one here is using the phone with extended battery and putting it in the case
I'm wondering the same thing!
there's a reverse clip holder in the case recommendations thread, it's not a complete case though as it only covers the front portion of the phone. would prefer a better solution though.
No
Your best bet would be to get this:
http://www.boxwave.com/products/activecase/active-case-cingular-8525_2110.htm
Use the top piece to protect your phone and for the bottom piece, you could color the deminsions with a marker on the case, then use a coat hanger, hold it under a fire (such as on a gas stove) until its red hot, then burn through the case and follow the lines you made through, until the panel is off, allowing the battery to poke out through the case. It would be risky, take alot of time but its worth it. If you want you can test it with this case, but I dont recommend this case at all, its cheap and its belt holster is garbage:
http://www.meritline.com/trans-smoke-cover-for-htc-8525.html
Sonic I just received the $4.99 black case. I will try your method now. Thanks.
Hehehe I messed up the case. For some odd reason the bottom piece won't lock into the cell phone. I'm going to look for a silicone black skin so I would just cut out the piece with a knife or something...
EDIT: My next victim http://cgi.ebay.com/Silicone-Case-D.../newreply.php?do=newreply&noquote=1&p=1246393
Reply8673QQrdZ1QQssPageNameZWD1VQQcmdZViewItem
Hi, just wanted to let you guys known the rubber/silicone whatever thingy it is worked. Only took me like 5 mins to cut the piece of with a xacto knife.
Yea, but don't you find the rubber impeads the sliding keyboard? I have the rubber too but i don't use it because of that.
tallshorty said:
Yea, but don't you find the rubber impeads the sliding keyboard? I have the rubber too but i don't use it because of that.
Click to expand...
Click to collapse
Nope I haven't had that problem. Only thing problem I got so far is that the front cover comes often.
I just received a replacement phone and my back cover does not snap in like on my other phone. The case fits pretty snug, but I noticed in the upper left corner if I apply some pressure you can tell that it is a bit loose. I'm just wondering, how is everyone elses battery cover fitting? debating if i want to go through the trouble of sending this back.
kimdoocheol said:
I just received a replacement phone and my back cover does not snap in like on my other phone. The case fits pretty snug, but I noticed in the upper left corner if I apply some pressure you can tell that it is a bit loose. I'm just wondering, how is everyone elses battery cover fitting? debating if i want to go through the trouble of sending this back.
Click to expand...
Click to collapse
Mine is tight all around. Even after 20 or so take offs.
I went shopping for an extra battery but came across this back cover/ rubber bumper. I like this case because it doesn't add any extra weight to the phone while still maintaining a low profile. All of the metal edge is covered. That is a pro and con. I love the metal bezel, so hiding it with the bumper takes away from the phone. BUT, it won't get dinged and dented like my buddy with the Note4.
The back cover has more texture than the original cover. It is more raised like small braille dots (if that makes sense). Also the bumper does not separate from the back cover. You can remove the original back cover and slide this case on. It will work, but it doesn't snap into the phone like the original cover. It stays in place by wrapping around the front. I kept my back cover on because of my Qi charger. So, it's slightly thicker. The bumper case does not push the Qi contacts into place; therefore no charging.
Attached are pictures.
I think this kind of case take off all the beauty of the device..
Good looking case. What is the Model number and where did you get it from?
chiefe said:
Good looking case. What is the Model number and where did you get it from?
Click to expand...
Click to collapse
Purchased at a Samsung store in Moscow, Russia. I was looking for them in the states but can't find it. Model: EF-PG850BSEGRU.
Let me know if you want one, I'm heading back to Russia in late April and can pick one up for you. It cost around 25USD.
Hi, any body knows the size of small screws to fasten the bottom cover. I lost all screws and didn't find yet new suitable screws.
Thanks in advance for any help.
Has anyone found a case that has magnets on the back so the cover stays in place when opened?