I just upgraded my XdaII from O2 to WM5 with this rom:
XDA_WM2k5_2.01a00WWE
everything seem working fine in the upgrade process but when in the end I need reset the xdaII its blocked on O2 boot screen...
I don't know what to do.. I tryed to reinstall it moer times but its always the same way...
some help?
thank u
Have u tryed to reinstall the official one from o2?
Related
hi everyone,
i have a huge problem. my rom flash for my i-mate (qtek 2020, mdaII, XDAII) hung during flashing (from 1.66 to 1.72 official i-mate rom) during the ce upgrade step 2. now my i-mate just hangs at the blue i-mate screen and i cant connect to it through pc anymore, get error 101. is there any way to get a good rom on it again (can i connect to the ppc by another way, other software or sd-card0 so it will work again, or does it have to be epaired at at a rapaircenter?
thnx, sorry for the bad english
See the pm i send you.
I have the same problem ...
plz tell me how u solve it
Best regards
plz help, i-mate dead after failed flash, error 101
Hi,
If all that happened was it hung during upgrade you can put the device into bootloader, power+d-pad+softreset button, and attempt upgrade again, but if OS you were upgrading to is corrupt causing the hang a new rom might be the way to go, www.buzzdev.net has everything i needed, or clubimate.com
I have same problem. My q-tec100 is reseting so I can' connect it to pc for flashing again. Please tel me what is bootloader and what is d-pad button so thad i can stop it from reset and connecting for flash
hi friends i have the same prob. somebody plz help me too
I tried to upgrade my imate jamin s200 to smart1_wm6_pp8mb. since the operation did not finished I unplugged the usb cable, therefore the machine didn't work and opening now. now some messages are appearing on the screen (IPL:2.15.0001; SPL 2.15.0001; GSM 02.19.21; OS:10.1.0.811)
i need your urgently help... How can i fix it this problem and upgrade my rom again?
Put your Jamin into bootloader mode (camera button hold+softreset with stylus), connect it via USB (not on a hub!!!!) with your PC and try to flash the last update of Qtek, Orange, iMate or something else you like! If your device booting after this correctly you can re-try the flash to WM6!
I switched yesterday many times between Qtek 2.20 Ger, Orange UK, O2 Ger nd smart1's clear WM6 and had no problems during this!
Thank you very much, could you plase upload here i cant find the last update ,
i''m waiting you..
i dont know what is my qtek last update How can i learn it?
When you want to know what ROM you have flashed to your device, go to Start -> Settings -> System -> Device Information! Here you can find all information you need!
By the way: the latest Qtek update for the S200 is 2.20! You can find it trough Gooogle or the board search! Good luck!
animelover said:
Put your Jamin into bootloader mode (camera button hold+softreset with stylus), connect it via USB (not on a hub!!!!) with your PC and try to flash the last update of Qtek, Orange, iMate or something else you like! If your device booting after this correctly you can re-try the flash to WM6!
I switched yesterday many times between Qtek 2.20 Ger, Orange UK, O2 Ger nd smart1's clear WM6 and had no problems during this!
Click to expand...
Click to collapse
Hi animelover,
Just a question...Do you use the OS extract tool to flash only the os without changing the IPL/SPL, or the roms that you wrote about have no IPL/SPL upgrade? I mean did you fash directly or you flashed only the extracted OS?
Thanks!
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
joesa said:
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
Click to expand...
Click to collapse
Don't know for sure that it will help, but when you want to connect to your PC in USB mode (bootloader) you should first disable "Allow USB CONNECTION" in the conections settingpanel of Active Sync.
thanks i'll give it a try
joesa said:
--------------------------------------------------------------------------------
mine is a G4 device IPL 2.09 SPL 2.09.0000
i flashed several times my prophet with diferent wm6 roms but i allways downgrade to wm5, cause some issues i didn't like,
this morning i tried to upgrade to wm6 again, made the procedure
1 Hard reset
2 connect to pc and wait to activesync to come up
3 run upgrade utility and wm5 flash started
after a while the upgrading process stucked at 5% and gave an error, i don't remeber whitch it was,
but since then my prophet always turns on in bootloader mode, you can do nothing, even turn it off, the only way to turn it off is removing the battery,
when you put the battery again and press power on it starts in bootloader mode
the diference that i notice it's that now the bootloader shows
IPL 2.09 and SPL 2.09 not anymore SPL 2.09.0000
so i tried again to flash the prophet but it always give me this errors
300 when i used the wm5 spanish rom
and 274 conection problem when i use the temp pdaviet rom or the fantastic mobiz rom
when i plug the prophet to the pc the bootloader displayes USB but activesync never starts
what could be my problem i used the correct G4 roms
please somebody help me
Click to expand...
Click to collapse
Try to search the new ROM update utility and try to reflash using it.
pda is dead
hey friends..!!
i have a problem with my neo..
got new update of wm 6. 4..0.0.0.1 version..
phone gets switched off by itself.. sometimes..
when sms comes or i recieve a call..
i fear it has become a black brick..
plz help me out..!!
and..
one more thing..
is there any was to restore my contact.. i had a backup in wm 5..
the back up file when restored in w m 6..
contacts don t open.. then again i hjave to hard reset it..
lost my contacts and documents.. but i stii have that back up file..
plz help me out..
replies awaited..!!
dj00912 said:
hey friends..!!
i have a problem with my neo..
got new update of wm 6. 4..0.0.0.1 version..
phone gets switched off by itself.. sometimes..
when sms comes or i recieve a call..
i fear it has become a black brick..
plz help me out..!!
and..
one more thing..
is there any was to restore my contact.. i had a backup in wm 5..
the back up file when restored in w m 6..
contacts don t open.. then again i hjave to hard reset it..
lost my contacts and documents.. but i stii have that back up file..
plz help me out..
replies awaited..!!
Click to expand...
Click to collapse
For the WM6, try Gullum V6 Touch...
Now for the contacts problem - flash WM5 back, restore your contacts and back up them with PIM backup 2.5 (use search you will find it in the forum somewhere).After reflashing the WM6 you will be able to restore them again. The other option is to use Outlook to synchronize.
chavdar said:
For the WM6, try Gullum V6 Touch...
Now for the contacts problem - flash WM5 back, restore your contacts and back up them with PIM backup 2.5 (use search you will find it in the forum somewhere).After reflashing the WM6 you will be able to restore them again. The other option is to use Outlook to synchronize.
Click to expand...
Click to collapse
It's beter NOT to use any backup software when you migrate from WM5 to WM6 or the other way around. Sync first with your desktop ans sync back after upgrading. The standard location are not the same, so it is messy when you replace the files to their original positions.
I got a dopod 838 pro of a friend with wm5 and upgraded it to wm6. This worked fine but i wasn't happy with the way it was behaving so I downloaded a original rom from dopod asia. When I flashed it it completley it **** itself at radio flashing. It now boots and gets stuck on the windows mobile screen and won't do anything, i've tried tapping the screen, pushing every button and hard reset a few times. Could someone please help me, I used this thing every day before it bricked.
If you have Hard sPLed your phone to SPl 2.10 olipro, I'd suggest trying to flash a stock rom with the sd card to see if you can restore your radio rom. You may have corrupted it and it may never work as a phone again. I'd still try the stock rom then reflash what you want if it works... You can find the instructions for sd card flashing on the wiki with a quick search...
Hope this helps... Cheers
I have flashed my qtek s200 with ``RUU-Prophet-AKU2.2-2.20-2.47.21-Jester-r1 `` all goes perfect after update completes bootloader screen appears i tried soft reset as well as hardspl but nothing works than i tried ruu nvid rom but it also bring no result. I also tried prophet recovery but the phone is still at bootloader.I got an suggestion to hardspl the phone & than update but after hardspl by nvid software the phone do not show any detuction witk computer..
Plz help if any one can....
shehzad143 said:
I have flashed my qtek s200 with ``RUU-Prophet-AKU2.2-2.20-2.47.21-Jester-r1 `` all goes perfect after update completes bootloader screen appears i tried soft reset as well as hardspl but nothing works than i tried ruu nvid rom but it also bring no result. I also tried prophet recovery but the phone is still at bootloader.I got an suggestion to hardspl the phone & than update but after hardspl by nvid software the phone do not show any detuction witk computer..
Plz help if any one can....
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=353547