HI guys,
I am planning upgrading my hermes v1605 from the vodaphone rom to a t-mobile rom.
How do I do this?
Do i just take the t-mobile uk extended rom files, and place them in the extended rom folder on my device and then do a hard reset?
How do i check my bootloader version?
Straight from the man ... for the search challenged ..
http://forum.xda-developers.com/showpost.php?p=1048178&postcount=93
press the OK button, power button and the soft reset button(located in a hole at the bottom next to the mini usb port) at once and hold for a sec or two....ull enter the tricolor screen....then u can press the soft reset button again to restart phone
Related
Hi dear freinds I upgrade my phone edition ppc to wm5 successfully after finishing and hard reseting my device this message raise(("Device authentication")) so I can't do anything with my ppc and I try using camera button and power for gettin into bootloader but it does't work can somebody help me How can I get into bootloader mode for upgrading again thanks
Push and hold the DPad(the button between the RED and GREEN buttons) and the power button and put the stick(stylus) in the hole(there is one near the chharge/USB plug) to resset your device.
Dont release the power and DPad buttons until in the screen you read SERIAL.
Uala you're in bootloader mode
Put the device in the cradle and it should change tio USB
Do the upgrade/downgrade ............. as you want
Regards
thats right
yup thats the right way bro... 8)
Does anyone know how to unbrick a HERM200 (TyTN) device?
After installing some programs i wanted to install Resco Explorer and then suddenly my device disconnected from my laptop i thought no big deal but the whole touchscreen is numb also none of the buttons on the TyTN are working. When i reboot the device i get the PIN screen i can enter the code also but is stays there and sometimes it skip's the PIN screen and goes directly to the Today screen but still the touchscreen and buttons are numb no response at all.
I can get in to boatloader by pressing left OK + power + reset.
But if i want to "re-flash" my device i goes into a reboot a the time de program is verifing my PDA.
Does anyone know what to do here?
OS = Black 2.5
Radio = 1.41.00.10
SPL = HardSPLv6 1.40 Olipro
Recently installed programs at the time of bricking the device are:
VITO Remote 4.1
VITO SoundExplorer
VITO Oscilloscope
then tried to install Resco Explorer 2005 and that was were the **** has hit the fan.
I would try a hard reset. If that doesn't help there is a sticky thread at the top of this section that is all about bricked devices (yours isn't really bricked, you are just having issues) that you can read through. Since you just installed Black 2.5 that thread would be the best place to discuss your issue.
Thanks
Thanks for the tip JasenR
How do i Hard Reset my device btw?
Nevermind i should read the wiki more often
Hard reset: Press and hold the Left SOFT KEY and Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device. You will be presented with a menu saying 'press R to reset, X to exit', if you press R Your device will be set back to factory default settings.
(The L/R soft keys are the "--" keys just up the start and OK buttons)
Now hope it works for me.
Thanx anyway JasenR
Hi..I am unable to switch on my o2 xda stealth. This happened after the battery was fully exhusted. After that I fully charged the battery and now it is showing green. But still I cannot switch on this.
Anyone having the same experience and any solutions for this.
I tried to soft reset, and hard reset ( flag + ok + power button )..but none of these are working.
I would be really glad if someone helps me in this regard
Thanks
Sasank
xda repair
dear
u press three button togatther
1 (windows) 2 (ok) 3 (camera) button
and hold three button and press power button
if on select boot menu
now working
if not
u go to repair centre
Hi, i'd like to share a tips to HARD RESET O2 Stealth.
Days ago, i just bough a Stealth since my O2 IIi bricked (not by software/hardware accident), but my toddlers (daughter and son) likes to play my O2 IIi like a bumpy toy and throwed it to the wall and floor like a toy car/doll (i love my children more than my O2 IIi
its a new challenge for me to play with it, and started to browse xda-developers to find any upgrade (but unfortunately i still cant find it.. anyone found an OS upgrade for Stealth?)
And googled some tricks for this stealth, and for Hard Reset i found many different instructions (d**n), and its make me confuse and failed to hard reset this device.
then, just by trial error i found the right steps to hard reset my O2 Stealth.
I post it in my website, pls see the steps here www.padusi.com
pls use search feature in that website if the instruction page disappears from the main page.
Nice Try and Good Luck.
Very simple.
Hold down the power key until you see 'goodbye'.
Hold down windows & OK keys and the press power key....keep all three keys pressed down till you see 'welcome'.
Wait for the process to begin...don't panic if you see any clcourful screens.
Just follw the instructions like screen align etc ....and Voila..DONE.
bye.
kalya said:
Hold down the power key until you see 'goodbye'.
Hold down windows & OK keys and the press power key....keep all three keys pressed down till you see 'welcome'.
Wait for the process to begin...don't panic if you see any clcourful screens.
Just follw the instructions like screen align etc ....and Voila..DONE.
bye.
Click to expand...
Click to collapse
after some minutes white screen and nothing happend after that
If you cant hard reset then try the engineering mode
this is from yuc
The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engineering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
I installed today the WM 6.5 23409 (found here : http://forum.xda-developers.com/showthread.php?t=500021).
Everything went right, during 2 hours, until it froze. So I decided to reboot it, and now it's frozen on the "Smart mobility" screen.
It just displays the red text (M04, B04, R 1.65.28.25, G 25.98.40.07H, D 2.09) and nothing else happens. I tried to install a new version, but the NIKI is not detected anymore on the usb cable...
I think i screwd up and i really don't know how to fix it !!
Thank you for your help and sorry for my english...
Perform a hard reset
To perform a hard reset on a device that is not responding to input or not booting to Windows, first remove the back cover of the device. Hold the "call" and "end call" keys on the front of the device and reset the device by sticking the stylus into the small hole to the left side of the USB port. The device will ask for confirmation. To confirm, press the "Enter" key on the keypad. On some devices you need to press the "Action" key instead of "Enter".
The device will reboot and be reset to factory settings.
Thank you for your help. It happened exactly what you said, I had to confirm by pressing the ENTER key, but the NIKI stops exactly at the same moment.
OK, I found the solution.
I did a hard reboot by pressing the start button + camera button + reset with stylus. It boots on the hard SPL and is recognized by PC via usb.
I installed the Light version of WM 6.5 23409 and until now, it seems to work perfectly
You didn't make a hard reset but you just enterd the bootloader (you don't need the styles for that, just start-button and camera-button is ok). but I'm glad you've solved your problem. Have fun with your Niki
hey guys my atom o2 stuck on o2 logo and than turn off...
i have updated it to 6.5 ...i used it for 10 days ..it works fine...but now it does not start.....
swapniladsure said:
hey guys my atom o2 stuck on o2 logo and than turn off...
i have updated it to 6.5 ...i used it for 10 days ..it works fine...but now it does not start.....
Click to expand...
Click to collapse
have you tried with hard reset device ??
to do a hard reset only by Press and hold the power button, and then use the stylus to press the soft reset button at the same time
at flashing of external rom it failed
Hakim Rahman said:
have you tried with hard reset device ??
to do a hard reset only by Press and hold the power button, and then use the stylus to press the soft reset button at the same time
Click to expand...
Click to collapse
i tried flashing.....at last flahing external rom it show failed.....
Why not try using a different ROM?