I have a huge really really huge problem my phone is dead.
I have a v1605 buyed in england and i'm from italy and yesterday i had problem after an hard reset the audio was not working anymore so i decided to put a new rom to solve the problem.I cheked my bootloader and was 1.04 so i unlocked my pda and i was able to load i-mate rom on my pda but i still having my problems with audio.So i tried with a newer version of imate rom but this time with bootloader 1.06 inside and i started to load on my tytn but unfortunatly during the operation i disconnect accidentaly the usb from the tytn so the computer stop the new rom istallation and now my tytn is dead with booatloder 1.06 without operating system and i can see only the bootloader page and i can't load any roms cause of the bootloader...Please help i'm desperete thinking to trow away from the windows my tytn.
why don't you try to flash i-mate rom with bootloader 1.04 again and downgrade the bootloader? it should take it as you have i-mate bootloader 1.06 on it and the CID should be the same.
with that said, i am not sure what audio problem you had but it sounds like that was not due to the rom as you could not solve it even after successfully flashing the i-mate rom. it could be a hardware problem but i don't know.
harryk1372 said:
why don't you try to flash i-mate rom with bootloader 1.04 again and downgrade the bootloader? it should take it as you have i-mate bootloader 1.06 on it and the CID should be the same.
Click to expand...
Click to collapse
Flashing a ROM doesn't mean the CID on your device will be switched or changed to the CID on the ROM, it will stay the same.
If he CID-unlocked with 1.04 before flashing his CID is "SuperCID" and should have no problems to flash any other ROM (no matter bootloader version).
However if he did not CID-Unlock it first the CID on his device is the original CID of a UK v1605: "VODAP001" (and there's no shipped rom available with this CID yet), so he will not be able to flash anything until a rom upgrade with his CID is available.
understand pof. then, would the purched unlocker from imei-check will be able to do the trick and downgrade the bootloader to 1.04 and make it SuperCID?
No, because imei-check unlocker needs wince to transfer the "fake" bootloader to the phone via an activesync connection first, and he's stuck in bootloader mode and can't boot to wince to enable activesync.
He didn't report if 'set 14 0' makes it boot to wince however, i guess he did not read the wiki before posting
pof said:
No, because imei-check unlocker needs wince to transfer the "fake" bootloader to the phone via an activesync connection first, and he's stuck in bootloader mode and can't boot to wince to enable activesync.
He didn't report if 'set 14 0' makes it boot to wince however, i guess he did not read the wiki before posting
Click to expand...
Click to collapse
thanks pof... it's not my problem but i hope he reads this and the wiki and take your advices from here. if it doesn't boot to wince, he won't be able to do anything until a rom upgrade with his CID is available.
harryk1372 said:
thanks pof... it's not my problem but i hope he reads this and the wiki and take your advices from here. if it doesn't boot to wince, he won't be able to do anything until a rom upgrade with his CID is available.
Click to expand...
Click to collapse
No way... i'm depressed...
eddy cudo said:
No way... i'm depressed...
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
read the wiki on upgrade problems and check if your device can boot to wince. if it can, there's a hope...
i had the same problem, but i was uploading to rom 1.35.255.102
now it is stacked in boot loader mode and write SPL-1.09
what I can do?
Te lo dico in italiano: LQCM, o meglio, LQCW (LEGGI QUEL CAXXO DI WIKI!)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Translation: I say it in Italian: RTFM or, better, RTFW!!
His case is similar to me before.
The device was disconnected before a WinCE ROM was finished flashing.
I do believe there will be bootloader 1.06 and no CID,
I can't flash anything at that time and believe send to service is the only way, currently. Sad to tell you this.
My case is the distributor replace the mainboard for me,
and I now flashed a SuperCID for safety.
sergiopi said:
Te lo dico in italiano: LQCM, o meglio, LQCW (LEGGI QUEL CAXXO DI WIKI!)
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Translation: I say it in Italian: RTFM or, better, RTFW!!
Click to expand...
Click to collapse
i did also "set 14 0" but nothing to do....
Related
1. Go to Google, search for DownGrade_SPL.rar
2. Connect your tytn to PC and wait until activesync completed.
3. Run M3100v3cUnlock.exe. Once you see checking device.... in DOS box and whilte screen on your tytn, close the program (Dos box) immedaitely.
4. Run ROMUpgradeUt.exe and follow the japanese wizard to complete the boot loader downgrade.
5. Reboot your tytn and then put it into bootloader mode agian, you should see SPL-1.04. Great!
6. Download pof's HTC_Hermes_SIM_Unlock_v2a from
ftp://xda:[email protected]/Hermes/Tools_and_Programs/HTC_Hermes_SIM_Unlock_v2a.zip
7. Flash the patched radio rom 1.16, then Reboot.
8. Copy HERM_Unlock_v2a.exe a small PPC app pof wrote into your TYTN memory.
9. Open File Explorer, run HERM_Unlock_v2a.exe on your TYTN and wait about 1 minute until it shows up a completed message. Reboot again!
10. Download mtty.exe from
http://wiki.xda-developers.com/uploads/mtty.exe
11. Disable ActiveSync, and then run mtty.exe, choose usb connection; Enter. You should see USB> prompt. Type in: info 2 . When you see 00000000 or SuperCID string. You are safe and ready to upgrade to the latest TYTN 1.35 Rom with bootloader 1.09.
Anybody tried this?
These are what I did on my Vodafone V1605 with bl 1.06. Guarantee working. Actually, this's not a new solution. It exists long time ago, but pof remove this file from wiki due to license issue. Some chinese fans downloaded this file before and shared on their forum. I hope pof won't remove this thread since the Downgrade file is from another website.
arcivanov said:
Anybody tried this?
Click to expand...
Click to collapse
hookhook said:
These are what I did on my Vodafone V1605 with bl 1.06. Guarantee working. Actually, this's not a new solution. It exists long time ago, but pof remove this file from wiki due to license issue. Some chinese friend downloaded this file before and shared on their forum. I hope pof won't remove this thread since the Downgrade file is from another website.
Click to expand...
Click to collapse
Great, many thx to you. I'm going to try it on SPL 1.09 now...
I confirm it downgrading SPL 1.09 to 1.04
Does this keep the os in place and change only the boot loader so one would be able to just upgrade the radio?
Will attempt myself.
barrydavisjr said:
Does this keep the os in place and change only the boot loader so one would be able to just upgrade the radio?
Will attempt myself.
Click to expand...
Click to collapse
Yes, it does. I have latest SA HTC firmware with 1.20 radio and SPL 1.04 now.
Confirmed this will allow you to downgrade bootloader only and do a radio only flash.
This thread WILL be closed.
Although files are not on this website you are providing links to them.
silent_killa said:
This thread WILL be closed.
Although files are not on this website you are providing links to them.
Click to expand...
Click to collapse
I just removed all the problematic links and hope this thread won't be closed to help more people.
This's just a temporary solution. Pof will bring out a completely free and much better solution in the future.
silent_killa said:
This thread WILL be closed.
Although files are not on this website you are providing links to them.
Click to expand...
Click to collapse
Tool.
Later, Lew
hookhook said:
1. Go to Google, search for DownGrade_SPL.rar
2. Connect your tytn to PC and wait until activesync completed.
3. Etc.
Click to expand...
Click to collapse
Works only for the M3100!?
i dont find DownGrade_SPL.rar
hookhook said:
2. Connect your tytn to PC and wait until activesync completed.
.
Click to expand...
Click to collapse
one question.
my device is stuck on bootloader mode and when I connect to Activesync it does not recognize my device.
is it a problem (I can't try now because I'm at work and I don't have the device by my side)?
I works¡¡. I had installed rom 1.35 and i could downgrade bootloader to 1.04, install radio rom 1.16, get supercid and now i can modify extended rom.
Thanks¡¡¡¡¡
marcocasali78 said:
one question.
my device is stuck on bootloader mode and when I connect to Activesync it does not recognize my device.
is it a problem (I can't try now because I'm at work and I don't have the device by my side)?
Click to expand...
Click to collapse
If your tytn is stuck on bootloader 1.06 (can't boot into the OS) and don't have a 1.04 ship rom matching its CID in the wiki, you can't downgrade your bl now. Please be patient.
Works only for the M3100!?
Click to expand...
Click to collapse
Works for all Hermes!
i dont find DownGrade_SPL.rar
Click to expand...
Click to collapse
Google the whole word: "DownGrade_SPL.rar"
hookhook said:
If your tytn is stuck on bootloader 1.06 (can't boot into the OS) and don't have a 1.04 ship rom matching its CID in the wiki, you can't downgrade your bl now. Please be patient.
Click to expand...
Click to collapse
my tytn was stuck on bootloader 1.09.
i did what you told me and now my tytn is stuck on Windows Mobile Logo.
I tried to re-insert te superCid, but I couldn't.
the problem, now, is that i can't go on. (just one time it starts good and i could see the today screen)
what do you suggest to me? my tytn keep on have the SPL-1.09!
marcocasali78 said:
my tytn was stuck on bootloader 1.09.
i did what you told me and now my tytn is stuck on Windows Mobile Logo.
I tried to re-insert te superCid, but I couldn't.
the problem, now, is that i can't go on. (just one time it starts good and i could see the today screen)
what do you suggest to me? my tytn keep on have the SPL-1.09!
Click to expand...
Click to collapse
1. What's the current CID on your device?
2. What version of rom and BootLoader did you use before flashing to HTC 1.35 bl1.09?
3. Did you run pof Hermes unlocker and mtty.exe to make your device SuperCID before flashing to HTC 1.35 bl1.09?
Worked on my Cingular 8525. Thanks! I was pretty nervous to be hacking on my new toy, but so far, so good.
hookhook said:
1. What's the current CID on your device?
2. What version of rom and BootLoader did you use before flashing to HTC 1.35 bl1.09?
3. Did you run pof Hermes unlocker and mtty.exe to make your device SuperCID before flashing to HTC 1.35 bl1.09?
Click to expand...
Click to collapse
1. when I use the command "info 2" in mtty i have back "HTCSF kEØ(HTCEUSB>", so I don't know my CID
2. 1.04
3. yes
PLZ PLZ
dont tell me to read about it cause the forum is to help people and to talk
i tried to upgrade my radio to 1.20 and when it finish it say error 114
i made reset and nothing i tried many times and nothing.
i have now the new 1.35 rom from HTC
the boot loader is 1.09
but before i put this version i crack my version and make it super CID
so why i cant upgrade the radio?????
What is written 2 times in bold in this page?????
bubu23 said:
PLZ PLZ
dont tell me to read about it cause the forum is to help people and to talk
i tried to upgrade my radio to 1.20 and when it finish it say error 114
i made reset and nothing i tried many times and nothing.
i have now the new 1.35 rom from HTC
the boot loader is 1.09
but before i put this version i crack my version and make it super CID
so why i cant upgrade the radio?????
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
You need to downgrade the bootloader to 1.04 to run the radio only upgrade. If you still have the bootloader 1.09 running on your device, the radio only upgrade will fail.
If your bootloader version is 1.09, you can buy the Imei-check unlocker to have bootloader 1.04. The HTC Hermes unlocker from imei-check is able to flash the 1.04 bootloader. It transfers the required files to the Hermes via ActiveSync before actually the unlocking key file with your IMEI is requested. The bootloader is flashed on the device after you enter the valid key file (you have to pay for that).
I SEE THAT IF I WANT TO CHANGE BACK TO 1.04 I NEED TO
upgrate to other version of HTC 1.04 then ill do every thing
bubu23 said:
I SEE THAT IF I WANT TO CHANGE BACK TO 1.04 I NEED TO
upgrate to other version of HTC 1.04 then ill do every thing
Click to expand...
Click to collapse
No, you still don't understand.
That method is only valid if your bootloader version is 1.06, if your bootloader version is 1.09, you can't downgrade because 1.09 will not allow to be "upgraded" to a lower version.
You should spend some time reading the wiki, otherwise you'll end up asking those pointless questions and will waste another 10's of hours or even days of your time asking those questions.
harryk1372 said:
No, you still don't understand.
That method is only valid if your bootloader version is 1.06, if your bootloader version is 1.09, you can't downgrade because 1.09 will not allow to be "upgraded" to a lower version.
You should spend some time reading the wiki, otherwise you'll end up asking those pointless questions and will waste another 10's of hours or even days of your time asking those questions.
Click to expand...
Click to collapse
That ins't right.
I made de upgrade ro 1.35 ROM
Then i have bootloader 1.09, so i do the downgrade on bootloader with the *TOOL*, then i'm able to patch the 1.20 radio.
Actually i have:
Rom 1.35
Radio 1.20
Bootloader 1.04
So it's possible, but read is very necessary :S
Panda_N_Shark said:
That ins't right.
I made de upgrade ro 1.35 ROM
Then i have bootloader 1.09, so i do the downgrade on bootloader with the *TOOL*, then i'm able to patch the 1.20 radio.
Actually i have:
Rom 1.35
Radio 1.20
Bootloader 1.04
So it's possible, but read is very necessary :S
Click to expand...
Click to collapse
well, that's only when you can get that tool thing from elsewhere, mate. not officially provided here in this forum.
Because it is paid, try find it on google or go to imei-check.co.uk
Panda_N_Shark said:
Because it is paid, try find it on google or go to imei-check.co.uk
Click to expand...
Click to collapse
then, that's what i already said in the above post #3.
harryk1372 said:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
You need to downgrade the bootloader to 1.04 to run the radio only upgrade. If you still have the bootloader 1.09 running on your device, the radio only upgrade will fail.
If your bootloader version is 1.09, you can buy the Imei-check unlocker to have bootloader 1.04. The HTC Hermes unlocker from imei-check is able to flash the 1.04 bootloader. It transfers the required files to the Hermes via ActiveSync before actually the unlocking key file with your IMEI is requested. The bootloader is flashed on the device after you enter the valid key file (you have to pay for that).
Click to expand...
Click to collapse
I need help phone stuck in bootloader and its not registering the usb syn cable being attached I think i just need to set it to boot to os. Have HARD-SPL.
ok got usb working again but ruu says it can't find device. is that because its already because its already in bootloader?.
edit- did an info 8 in mtty and got this
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
EDIT- finally got home and was able to reflash os with sd card and phone works now.
but what did you do to be able to flash?
everytime I try to flash it enters the BL and hangs. Then it says it cannot update. I've got a 1.09 BL
thanks
Read here:
http://forum.xda-developers.com/showthread.php?t=286755
giving more data:
which bootloader version on your device?
1.09
which rom on your device?
1.35.255.2
which RUU are u using?
HTC WWE version
which rom are u trying to flash?
2.11.255.1
Bootloader 1.09 is not compatible with new RUU version inside HTC's 2.11.255.1 ROM.
If you just run the shipped exe file (without unpacking), it will first upgrade your bootloader to 1.11 using the old RUU, then launch the new RUU and flash your rom.
BTW, i suggest you to read the hardSPL thread before attempting to upgrade
Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.
But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!
If I reboot it no problem, everything is working.
thanks for you help!!
ok, now that you have HardSPL-1.11 on your device, do this:
1. Use winrar to extract the contents of RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10_108_Ship.exe
2. You will see a file named RUU_Inside.exe
3. Use winrar again to extract the contents of RUU_Inside.exe
4. Run the RUU you'll find here, with device in bootloader mode.
Keep in mind that this will overwrite HARD-Spl with the shipped 1.11 bootloader, if you don't want that, read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide
Well it worked!!! Thanks a lot!!!! any explanation for this? (i forgot to tell I was using vista)
But... eheheh now I found out http://forum.xda-developers.com/showthread.php?t=297849&page=2
and it happens the same.. when I run it... (after winraring the main file) it hangs on the BL! Damn!!!
Muster said:
(i forgot to tell I was using vista)
Click to expand...
Click to collapse
boh!
I know I know awfull mistake!!!
Why does this happens when I try to update? ANd why it worked the way you said it would?
Muster said:
Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.
But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!
If I reboot it no problem, everything is working.
thanks for you help!!
Click to expand...
Click to collapse
uhh... it should say SPL-1.11.Oli
It did not!! It says now 1.11!!
when I tried the upgrade to WM6 it used it's own bootloader 1.09 Ds and it changed again. Is it possible that 1.09 BL is definitevely not working in my TyTN?
HELP HELP
Hi All ..i'm totally lost here. I've tried to look for guideline to downgrade to original SPL 1.04 but i cudn't find any.I installed the latest m3100 unlock software v3a doing so my SPL is now version 1.4 Olipro. For warranty purposes how do I downgrade back to 1.04? I'm sorry this problem might have been addressed somewhere on the forum..if so cud someone provide the link to the thread on this. thank you so much.
Click on the mrvanx guide at the bottom of my signature, it will tell you how to downgrade in the guides.
mysharif said:
HELP HELP
Hi All ..i'm totally lost here. I've tried to look for guideline to downgrade to original SPL 1.04 but i cudn't find any.I installed the latest m3100 unlock software v3a doing so my SPL is now version 1.4 Olipro. For warranty purposes how do I downgrade back to 1.04? I'm sorry this problem might have been addressed somewhere on the forum..if so cud someone provide the link to the thread on this. thank you so much.
Click to expand...
Click to collapse
I have been there mrvanx guide. but he don't have the solution to this problem. Just to downgrade the rom to wm5 not the SPL.
mysharif i think we have to shout again.
Help us anybody there we are stuck here.
OK guys the SPL downgrade can be done by downgrading to SPL 1.10.oli then flash any ROM with SPL 1.04 in it.
The only reason i can see that you wish to downgrade to 1.04 is because of a warranty issue. What is the problem with your devices??
You are great. I hope it will work for my Imate JasJam. Last night I was flashing my ROM with the original ROM but modified with NBH decomplie too by dutty. Before that I wrecked my device as I used the flashing of ROM using the latest sensation of loading the SSPL to RAM by des. That was my mistake that I used the original ROM. Then I removed the USB cable as it was taking too much time and because of danger to my imate I did that. Anyhow I got the NO GSM error but then I ran the Dutty's WM6v2 cooked ROM and it fixes all the things I am using it now.
The reason for my Imate JasJam degrade is my jog is not working according to its function. You know jumping from field to field. I didn't found any of that problem solution till the page of 30 in threads and posts. I am searching but if anybody knows the link. Kindly help me. So that I will save a trip to see the warranty people. (here we don't have ladies receptionists )
Sorry for the stupid question, how do I downgrade from Oli 2.10 to Oli 1.10
Il write a guide on it...too many PMs about this.
mysharif said:
HELP HELP
Hi All ..i'm totally lost here. I've tried to look for guideline to downgrade to original SPL 1.04 but i cudn't find any.I installed the latest m3100 unlock software v3a doing so my SPL is now version 1.4 Olipro. For warranty purposes how do I downgrade back to 1.04? I'm sorry this problem might have been addressed somewhere on the forum..if so cud someone provide the link to the thread on this. thank you so much.
Click to expand...
Click to collapse
I have the same problem. My touchscreen is dud and Softbank is very anal about the bootloader and warranty. im stuck with Olipro 2.10 and tried flashing the latest softbank rom. When i try via USB/Windows it gives me error 260.
Flashing with MicroSD works, but after a few attempts, its still Olipro bootloader...any ideas?
aquasesh said:
I have the same problem. My touchscreen is dud and Softbank is very anal about the bootloader and warranty. im stuck with Olipro 2.10 and tried flashing the latest softbank rom. When i try via USB/Windows it gives me error 260.
Flashing with MicroSD works, but after a few attempts, its still Olipro bootloader...any ideas?
Click to expand...
Click to collapse
Ofcourse...because flashing an original RUU it doesnt recognise the new bootloader (Hence your 260 error), and HArdSPL doesnt allow itself to be overwritten by a retail RUU. IF you read through the HArdSPL threads you would know this.
mrvanx said:
OK guys the SPL downgrade can be done by downgrading to SPL 1.10.oli then flash any ROM with SPL 1.04 in it.
The only reason i can see that you wish to downgrade to 1.04 is because of a warranty issue. What is the problem with your devices??
Click to expand...
Click to collapse
Hmmm, just yesterday (Thursday) I was asked by a VP at our company if that could be done. I was reluctant to say yes, but mrvanx comes thru with a fix.
The VP is in fact worried about having to return some devices to Vodafone, and he want to make them look "original" when they go back.
GreatGrey said:
Hmmm, just yesterday (Thursday) I was asked by a VP at our company if that could be done. I was reluctant to say yes, but mrvanx comes thru with a fix.
The VP is in fact worried about having to return some devices to Vodafone, and he want to make them look "original" when they go back.
Click to expand...
Click to collapse
Just flash SPL 1.10.oli.......................then flash a vodaphone ROM, dont use 'force SSPL', just use autodetect.
well to get spl 1.04 all u have to do is take rom koch and the wm5 rom u are downgrading to. first downgrade os. then take that rom and using rom koch split it into parts and just take the spl and make it into a nbh and use the custom ruu on here. select force sspl and itll make ur spl 1.04. this is a quick guide and do this at own risk. using this method i got my first 8525 to aku 3.5 att and original spl. if marvanx comfirms i didnt make any mistakes i can make a new thread with pics and all so we cna add this to resources and stop the questions.
Pawel062 said:
well to get spl 1.04 all u have to do is take rom koch and the wm5 rom u are downgrading to. first downgrade os. then take that rom and using rom koch split it into parts and just take the spl and make it into a nbh and use the custom ruu on here. select force sspl and itll make ur spl 1.04. this is a quick guide and do this at own risk. using this method i got my first 8525 to aku 3.5 att and original spl. if marvanx comfirms i didnt make any mistakes i can make a new thread with pics and all so we cna add this to resources and stop the questions.
Click to expand...
Click to collapse
Or you could just wait until my guide is finished??
You dont need to use the rom koch ... duttys nbh tool is far more appropriate for this since we aint doing any cooking.
yea your right I just wanted to reduce your work load.
mrvanx said:
Or you could just wait until my guide is finished??
You dont need to use the rom koch ... duttys nbh tool is far more appropriate for this since we aint doing any cooking.
Click to expand...
Click to collapse
Hi mrvanx, some input to go into your guide (in case you havent come across this yet).
While flashing 1.10Oli under Vista, users may run into a problem where after loading SSPL and the phone goes into (SSPL) bootloader mode, the RUU program cannot detect the phone and returns an error.
This is due to the Vista drivers for HTC USB Sync. The driver needs to be manually "updated" just like in your Vista flashing guide. In this case, while the phone is in SSPL bootloader mode, go into device manager, replace the default HTC USB Sync driver with the USBAS one from your Vista flashing guide.
Then soft reset the phone, and try again. Worked for me.
For some reason, SSPL bootloader may appear as a different device to Windows than the hard/standard bootloader, so even if the Vista procedure has been performed before, it looks like it needs to be done also for SSPL.
Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
rakdoll said:
Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
Click to expand...
Click to collapse
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
This guide assumes you already have flashed ROMs and Other components and you are familiar with the process.
NOTE: By downgrading your SPL version your device is more vulnerable to being permenantly bricked if a flash goes wrong, by following this guide through YOU accept responsibility for any problems faced due to this operation. As with other downgrade guides this is NOT intended as a guide for claiming the warranty of the device having flashed components which are not authorised by the manufacturer or carrier.
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
Click to expand...
Click to collapse
And *that* is the reason we helped you, so that now you help others. One day, rakdoll will help someone else. That is why we are all here. Nicely done!
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
revert back
this is what i used to flash mine back to enable original rom to be installed ,so i could take phone back for warrany reasons
Korpse said:
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
Click to expand...
Click to collapse
Shouldn't need to access OS. You should be able to do it by putting it in BL mode... THEN plug it into the usb. Then start the updater.
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Korpse said:
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Click to expand...
Click to collapse
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Korpse said:
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Click to expand...
Click to collapse
Oh interesting. A nuance I hadn't picked up on. So, when using the Force using SSPL" option in the flashing utility, you must be able to access the Phone OS? That surprises me, I thought that the RUU utility would put it on the phone even in BL mode and execute it? Hmm... strange. I guess if it is an exe, it needs the OS to run, though. Sort of makes sense. Sorry about the misdirection.
todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Hi,
I'm trying to downgrade to the original SPL (I'm trying to get hold of 2.03 but can't seem to find it), so am using 1.06. I've been able to downgrade to Oli1.10 from Oli2.10, but it won't go back to 1.06 from there, after the RUU says successfully completed the SPL is still the same.
Any ideas?
Cheers
downgrade phone for rogers warranty
Hi Guys,
I need to downgrade my phone as well for warranty purposes. Unfortunately Mrvanx's guide is offline at present. Can any one of you give little further detail about what I need to get back to orginal rom/radio/spl and bootloader. Or in shor to be able to send it back for warranty. I do have a new Rogers phone if that can be of any help.
It is from Rogers and currently my boot loader screen says following:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro
Under Device Information:
ROM version: FARIA.R-32
ROM date: 11/06/07
Radio version 1.54.07.00
Protocol Version 32.86u.7020.23H
ExtROM version: BIGSTORAGE
My replacement Rogers Phone has following:
HERM200
IPL-1.01
HERM200
SPL-1.11
Under Device Information:
ROM version: 1.34.631.14
ROM date: 04/17/07
Radio version 1.42.00.00
Protocol Version 32.75.7020.18H
Can anyone please tell me if it is even possible to do this downgrade.
Thanks
B.
why dont you just brick the phone if you are worried about them complaining over the boot loader version. If you cant access the phone i doubt they will be able (or even be bothered) to
Could you please let me know what you did? Did you downgrade To the original Rogers Radio and SPL ? Do you by any chance have all the original Rogers files (WM5, SPL, Radio,...)?
I am with Rogers too and just unlocked SIM (not CID) and installed WM6 (official HTC)
I am wondering how I could lock SIM again if I need to return the phone for Rogers warranty? or unlocking SIM does NOT void the Rogers warranty?
Thanks
Downgrade to SPL 1.11
Hi is anyone able to figure out how to downgrade from SPL 2.10 Olipro to SPL 1.11? I have tried Mr Vanx guide but at the end of the process, I get Error 260. Not sure if I am doing anything wrong.
Do I have to downgrade to SPL1.10 Olipro, before I downgrade to SPL 1.11?
Thanks
I am having some issues downgrading back to an original SPL. I've searched throughout the site and have found a lot of conflicting advice, although this thread seems to be the most relevant.
I started out the process with SPL: 2.10.Olipro
I downgraded to 1.10.oli.
This process was successful in that the bootloader screen now says that the SPL version is 1.10.oli.
Now, when I try to flash the OEM version of SPL, the phone asks the following question:
You would like to run jumpspl.exe
If I say yes, the screen goes gray and says load... but I end up with a 260 error.
I have tried turning off the usb connection in the active sync and starting from the bootloader as mentioned here, but that just ends up giving me a 264 error.
Any suggestions would be appreciated.
Cheers,
~Hat
* edit *
Post #5 from here fixed the issue.
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
<snip>
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Click to expand...
Click to collapse
Okay, Im back to 1.10oli, but how do I know if I need to go back to SPL 1.04 (includes IPL 1.00) or SPL 1.06 (includes IPL 1.01)?
OK people, please tell me you have looked at the updated guide right??
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=19&Itemid=27
Yes, but the choices are,
1.04
1.06
1.09
1.11
2.03
and I don't know how to tell which one is stock for my phone. I assume I need 1.04 since my bootloader says IPL-1.00 but I'm not sure because I know that used to say IPL-1.04, and since it appears that that can change for some reason, I want to make sure I get this right so I can get this waranteed. Im going to sell it on ebay and get the new HTC Fuze as soon as AT&T releases it.