Sos,sos,help,help. - iPAQ rw6828, XDA Atom Software Upgrading

I had a wrong,put Atom-exec bootloader file "EBOOT.nb0" into my Atom SD card,and press 'Camera+SR' into DSUU mode updated Atom bootloader.
After Atom reset,I found my Atom nerver enter DSUU mode,if I press 'Camera+SR' , Atom will reset,BUT CAN'T ENTER DSUU MODE.
If Atom connect with Async4.2 to Update, when I run "Device Software Update Utility.exe",it can display Atom ROM version and show Update button,then click UPDATE,Atom will reset like softreset but can't display Update Interface.
It had kill bootloader, Wu,WU,WU.
How I reflash OLD BOOTLOADER? Let Atom can Enter DSUU MODE?
HELP!HELP!HELP!HELP!HELP!

No Anybody can help me!
No Anybody can help me!

szzls said:
No Anybody can help me!
Click to expand...
Click to collapse
sorry to inform your atom is stuck with that rom as you have no bootloader.

homer285 said:
sorry to inform your atom is stuck with that rom as you have no bootloader.
Click to expand...
Click to collapse
Have any software can rebuild the BOOTLOADER?

no. but from other hand, now you have a good experience for the future!

Related

ATOMs..DOWNGRADE ROM

@all
anyone have a solution on how to downgrade rom..
i have a ATOM and upgraded to ATOM EXEC rom..
theres some guide in here but its inside of other thread and its not working..
please help us..i know im not the only one have a problem like this..
thanks in advance..
-=[serialzs]=-
If you have Atom Exec ROM, then the bootloader keys are Camera+Reset. If you can enter bootloader, you can now upgrade to the usual XDA Atom ROM.
Cheers,
Jiggs
jiggs said:
If you have Atom Exec ROM, then the bootloader keys are Camera+Reset. If you can enter bootloader, you can now upgrade to the usual XDA Atom ROM.
Cheers,
Jiggs
Click to expand...
Click to collapse
where i can put the bootloader? can you help me? please..
-=[serialzs]=-
serialzs said:
where i can put the bootloader? can you help me? please..
-=[serialzs]=-
Click to expand...
Click to collapse
press camera+reset button. you should see bootloader screen. From here, upgrade using the procedure I discussed in the aku3.3 thread.
cheers,
Jiggs
thanks for the help but i figure it out on my own now..i done it with something i dont think earlier because im too excited..hehe..
now i have a atom rom back again..
i will guide people have same problem..hope i can help..
-=[serialzs]=-
o2 atom upgrade problem
hi
i need ur help
i have o2 atom i upgrade to exec now i can not go back
it give me error in connection
please help
all_brother2002 said:
hi
i need ur help
i have o2 atom i upgrade to exec now i can not go back
it give me error in connection
please help
Click to expand...
Click to collapse
what version of atom exec you use?
-=[serialzs]=-
Well, I managed to downgrade my ROM back to the original Atom (my sig isn't updated - had problems with the extROM wiping itself) - but I was kinda lucky.
Y'see, the AE hack rom I use has an updated bootloader that won't let you do a USB firmware update unless you're activesync'd.
The only way to solve an ExtROM wipe was to reflash the device, so I did. Using the hack ROM DSUU - at this point, the original ROM won't recognize the device - I found that it usually takes a few tries for the extROM update to go through (extROM format fail) - when it fails, your phone will be stuck in bootloader (Connect a USB cable). Repeated attempts to flash the phone solves the problem.
So when my extROM inevitably disappeared again, and I hit the extROM format fail again, I decided I had enough and tried using the original Atom0426-0822 ROM.
It went through this time.
Seems that the only way to bypass the bootloader lock is to semi-brick your device. >_>
Just a question to all of you who are more experienced than me
I want to change my atom exec wwe to cht, can anyone tell me how to bypass the device country id error. do i use an spl? and are these spl programs device specific? or do i use the bootloader mode? Can someone explain that to me?
Thanks all in advance.
Bootloader mode works as long as you aren't using the Atom Exec hacked ROM (bootloader will tell you to use Async if you try). To upgrade, go into the bootloader, connect via USB, and run the DSUU from the computer.
You know you did it correctly when your unit's current firmware information is read as "0" by the DSUU/
Ultimate Chicken said:
Bootloader mode works as long as you aren't using the Atom Exec hacked ROM (bootloader will tell you to use Async if you try). To upgrade, go into the bootloader, connect via USB, and run the DSUU from the computer.
You know you did it correctly when your unit's current firmware information is read as "0" by the DSUU/
Click to expand...
Click to collapse
Strange, i already did that, and got the "0" from DSUU, but when i start upgrading, the bootloader spits out a message saying that i should connect with OS mode.
Anyway, I've edited the diskimage_Ver.nb0 file to do it.
Hi,
I have the same problem :
- bootloader : ok
- firmware 0 : ok
but connection error !
Do you have an idea ?
Thanks a lot.
bedav said:
Hi,
I have the same problem :
- bootloader : ok
- firmware 0 : ok
but connection error !
Do you have an idea ?
Thanks a lot.
Click to expand...
Click to collapse
Hi guy the main key on the file call EBOOT everytime when you want dowgrade your OS to normal ATOM just put this file to you SD card then use the bootloader mode you can see "imge downloading" just wait for a second it will reboot again . then you can use the DSU mode to flash your device
thats work !
Thank you very much !
HELP on my atom exec
w/o reading, i downgraded my atom exec to atom...
hw can i bring back my atom exec default WM5 ROM?...
am planning to upgrde to WM6 aftr...

Help! Please save me! (NOT BRICKING)

Everybody plz help me!
I haven't bricked my Atom Exec, but I can flash it no more!
I was trying to cook my own ROM, but after I successfully flashed it, I found it very buggy. I wanted to flash it back, but the device cannot establish a standard patnership with ActiveSync 4.5, only guest mode can be used. When I tried to used DSUU, it stuck. When I entered bootloader (060613 MN2), it refused to DSUU, saying that it must run under Sync (but I can't! ), and when I inserted the SD card with diskimg.nb0, it showed "SD download complete" immidiately after beginning, and nothing flashed.
How can I recover my system? Please help me! Thank you very much!
BoomerCE said:
Everybody plz help me!
I haven't bricked my Atom Exec, but I can flash it no more!
I was trying to cook my own ROM, but after I successfully flashed it, I found it very buggy. I wanted to flash it back, but the device cannot establish a standard patnership with ActiveSync 4.5, only guest mode can be used. When I tried to used DSUU, it stuck. When I entered bootloader (060613 MN2), it refused to DSUU, saying that it must run under Sync (but I can't! ), and when I inserted the SD card with diskimg.nb0, it showed "SD download complete" immidiately after beginning, and nothing flashed.
How can I recover my system? Please help me! Thank you very much!
Click to expand...
Click to collapse
have a try, remove your SD card, and go into bootloader mode, then run DSUU, good luck.
raftcham said:
have a try, remove your SD card, and go into bootloader mode, then run DSUU, good luck.
Click to expand...
Click to collapse
Yeah, but the bootloader told me that it can only flash under Sync mode
You have to flash with another Atom Exec ROM. No choice. And being in guest mode doesn't disable flashing last I checked.
Don't worry!
You have to flash your bootloader with an older version, and then flash new rom in bootloader mode.
First: You need extract file eboot.nb0 from the rom “Xda-Atom-ENG-20060614” and copy this file to the root directory of your Mini SD card. Insert this card into your Atom and press Reset + Camera to go into bootloader mode. Your atom will download this new bootloader and then reboot.
Becareful!Be sure that the file is copy 100% correctly to your card and plug your Atom to a charger before upgrading. Remember that uprom from SDcard is dangerous.
Second: remove your sdcard, go into bootloader mode again, connect your Atom to PC and run DSUU to flash rom (DSUU might stuck at 6% while flashing the extended rom). But at this time, you can press reset and it will start the OS.
If your Atom boot normally and you can run camera apps, your phone is OK. If it not, you have to connect it to PC and run DSSU one more time.
Good luck! Sorry for my bad English!
Problem solved and thanks to everyone
Hi, i have the problem with the threadstarter. Wanted to change my Atom Exec cht rom back to wwe version. But i keep encountering bootloader telling me that it can only flash under Sync mode.
Anyone could help?
Thanks
wonder12 said:
Hi, i have the problem with the threadstarter. Wanted to change my Atom Exec cht rom back to wwe version. But i keep encountering bootloader telling me that it can only flash under Sync mode.
Anyone could help?
Thanks
Click to expand...
Click to collapse
Run CHT DSUU as normal; then before the final confirmation, copy WWE ROM files and overwrite all CHT files, then confirm flashing. That may help. There was a thread about downgrading Atom Exec ROM to Atom ROM that can also help you.

after install 3.3.3 my atom bricked it stuck o2 screen pls help

hi
i updated my atom rom version to 3.3.3 three days ago.It installed completed i used this rom 3-4 hours then i was freeze and i try to reset it. it didnt respond so i decided to hard reset to my atom.I tried to hard reset now it says "device clean boot....." it stuck this screen then i try to reset the device then it stuck o2 screen it didnt pass to align screen. i cant use my atom for three days
Please help me......
remove the battery for a while.. then try hard reset / reflash
i try this method but it is same it doesnt work
did u try the instructions posted in aku 3.3.3.??..
"
For those of you who have downloaded and flashed using SD Card method who ended up in a brick! ITEX recovers his Atom by following procedure:
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode. Just flash the above DSUU.
"
Does it have a chance to use wm6?
joolawan said:
Does it have a chance to use wm6?
Click to expand...
Click to collapse
it can barely use WM5 and anyway these chinese splash their advertising for WM6 all over the place in hope ppl will buy their rom, until I see it running in my device or get confirmation from someone reliable (such as Jiggs) I dont believe a word of it and besides the 3.3.3 rom is very fast and ten times better than any actual official release
yes i tried to that method too. it is same it still stuck on o2 screen. it doesnt pass to align screen..please help me
my problem didnt solve pls help me i cant use my atom..........
plsssssssss help meeee...........
plsssssssss help meeee...........
R U able to go to bootloader mode ?...
ironeagle said:
R U able to go to bootloader mode ?...
Click to expand...
Click to collapse
try to be on the bootloader and reflashed the ROM. try to search same cases in the forum. I think they solved the problem alike.
yes same to problem. i dont re enter bootloader again :S
did DSUU Recognize your ATOM ?..
Connect your ATOM to PC (using USB)
Run DSUU
Try to flash it..
i can enter bootloader mode and i can update rom but after this proccess it says "device clean boot......" and it freeze . it doesnt pass to align screen
plssss help meeeeeeee.
Which ROM you flashed?..
i flashed orginal atom rom i downloaded from seeo2.com
pls helpppp meeeee my atom is dead
are u using o2 atom exec or just atom?
cuyz i've got o2 atom exec..maybe i could flash it with o2 atom (yeah i cant flash anything with dsuu)
mine is o2 atom
did u amend any thing from the original ROM from seeo2? I mean you flash your atom with the original ROM...0426? without replacing the extended ROM...etc?

My Atom Life goes Brick

Help!!!
My Atom Life goes Brick.
Yesterday I am planning to upgrade my atom life from wm5 CHT to wm6 ENG.
Unfortunately, I wrongly downloaded the Atom Exec rom in the forum and put into my atom life. Of course, flashing not successful, however the atom life stuck in the "device booting..." screen.
I can enter the bootloader and I try to reflash the correct rom. But either CHT or WWE rom also not successful with the same reason: "Customer or Model ID Error"
I already try to edit the pass.32 file and nothing changes and give the same result!
Anybody can tell me how can I refalsh my device?
Or I can use SD to reflash my machine?
henryto said:
Help!!!
My Atom Life goes Brick.
Yesterday I am planning to upgrade my atom life from wm5 CHT to wm6 ENG.
Unfortunately, I wrongly downloaded the Atom Exec rom in the forum and put into my atom life. Of course, flashing not successful, however the atom life stuck in the "device booting..." screen.
I can enter the bootloader and I try to reflash the correct rom. But either CHT or WWE rom also not successful with the same reason: "Customer or Model ID Error"
I already try to edit the pass.32 file and nothing changes and give the same result!
Anybody can tell me how can I refalsh my device?
Or I can use SD to reflash my machine?
Click to expand...
Click to collapse
You can try the procedure in the WIKI under upgrading problems. Since your bootloader has been changed. BUT instead of using the ATOM eboot.nb0, use the Atom Life eboot.nb0 as replacement.
Good Luck!
jiggs said:
You can try the procedure in the WIKI under upgrading problems. Since your bootloader has been changed. BUT instead of using the ATOM eboot.nb0, use the Atom Life eboot.nb0 as replacement.
Good Luck!
Click to expand...
Click to collapse
Jiggs,
Thanks for your suggestion!
I have try but not useful!
Henry
same too me
same to me got other solution ??

Xda atom pure dead after upgrade wm 6.5

Dear All, Please help me how to repair my ATOM.
My ATOM PURE was dead after upgrade from wm 6.1 to wm 6.5.
LCD blank all button doesn't work.
which ROM did you download ?
what was the Setup you used for Flashing - OS Only, OS+Ext ROM, etc...
Did you notice any error while flashing?
After you try to start the PDA now, do you get any LED / LIGHT or ray of light on LCD.
Did you try starting with another battery...
Sorry, but will ask more questions sooon. Actually trying to troubleshoot the issue.
hehehehe, bad news..
hehehehe
suga_ngr said:
Dear All, Please help me how to repair my ATOM.
My ATOM PURE was dead after upgrade from wm 6.1 to wm 6.5.
LCD blank all button doesn't work.
Click to expand...
Click to collapse
i also have the same expirience with you, my phone totally like dead, no respone at all!!! even switch on or press any buton. any body can help?
We need to know which ROM you downloaded to upgrade your Device with... if you don't tell us, then all we can do is sit around making wild guesses without getting anywhere...
Dude, chill, for all you know its a bot your talking to
i have your answer
steven3889 said:
i also have the same expirience with you, my phone totally like dead, no respone at all!!! even switch on or press any buton. any body can help?
Click to expand...
Click to collapse
Just pull out the battery for a while. Next, hold down the on button and the camera button at the same time, and then put the battery back in. this takes some practice to get it right. After it will boot up to MN1 bootloader.
Cheers
Dead ATOM Pure
jadephyre said:
which ROM did you download ?
Click to expand...
Click to collapse
My friend
i was try to upgrade from wm 6.1 to 6.5 from arunk2 link, it's ROM CE OS 5.2.210501.
thanks very much for your cooperation and i hope my atom can be life again
jadephyre said:
We need to know which ROM you downloaded to upgrade your Device with... if you don't tell us, then all we can do is sit around making wild guesses without getting anywhere...
Click to expand...
Click to collapse
that ROM come from ARUNK2 link.
How to recover dead atom pure after failed wm 6.5 upgrade
suga_ngr said:
that ROM come from ARUNK2 link.
Click to expand...
Click to collapse
HOW TO RECOVER DEAD ATOM PURE AFTER FAILED WM 6.5 UPGRADE
Step 1. Pull out the battery
Step 2. Do the following 2 things simultaneously:
1) Press down the Camera Button (right side of your Atom)
2) While holding Camera Button down, put the battery back inside.
Step 3 Wait for 2 seconds. Now your Atom will automatically re-boot to MN1 Bootloader.
Once you are in MN1 Bootloader, connect to your PC by USB link, and upgrade with any WM 6.1 ROM.
Good luck
Christian
GOOD NEWS
Dear KLAPEREK
I have been do all your command and now my atom is runing well, so thank you very much for your help.
by the way iam come from Indonesia, i would ask regarding wm 6.1.
1. now iam using wm 61 ce os 213 pdavie all device are runnig well ( a2dp bluetooth, wifi, gprs,infra red ).
2. do you know how to fix stk software ? everytime when i try to use stk on the password box always popup please inset something after iam fill that box with passwort string.
3. what your suggestion for the best wm for atom pure ?
4. iam realy appreciate with your help regarding my atom problem
5. do you have some blog or email
6. this my e-mail : [email protected]
klaperek said:
HOW TO RECOVER DEAD ATOM PURE AFTER FAILED WM 6.5 UPGRADE
Step 1. Pull out the battery
Step 2. Do the following 2 things simultaneously:
1) Press down the Camera Button (right side of your Atom)
2) While holding Camera Button down, put the battery back inside.
Step 3 Wait for 2 seconds. Now your Atom will automatically re-boot to MN1 Bootloader.
Once you are in MN1 Bootloader, connect to your PC by USB link, and upgrade with any WM 6.1 ROM.
Good luck
Christian
Click to expand...
Click to collapse
hi,
i was follow your step, but still failed to boot on my o2 atom pure,
take out baterry > hold camera button and put back battery at the same time. any other solution?
Dear
First you try to go in boot loader mode and then you try try upgrade rom, if your atom did not power on then you lost his boot loader.
don't worry we have the solution to repair the boot loader, first of all you try to power it on in bl mode if not then mail me at "[email protected]" i will tell you the complete procedure for repair the atom with help of jtag.

Categories

Resources