Thanks POF, my 8525 is unlocked, but I have gone through hell with Vista so just to let you all know that "don't try these upgrades on VISTA".
I have read many posts and finally got it to unlock. In any case, here is what I did (on a XP box with activeSYNC 4.2 - it is running all the time for each of the steps below):
1) on XP, connect the phone to XP and make sure ActiveSync see the phone. Run the exe in 1.30 ROM for Cingular to download the SPL to 1.04. After this the phone will reboot/restart itself.
2a) On XP, with ActiveSync running and connected, run POF's MaUpgradeUt_noID.exe within the unlocker v2a xip file to upgrade the radio to version 1.16. If it fails with ERROR 114, go to step (3); else go to step (2b).
2b) If the first time failed, DON'T TOUCH THE PHONE. Run the exe again and the second time should run fine. There is a 114 error at the end and it is OK. Once you get the 114 error, soft-reset the phone before next step.
3) On the phone, flash with POF's unlocker (v2a) ON THE PHONE MEMORY HERM_Unlock_v2a.exe (in the zip file same as above download for unlock v2a). There is a success notice at the end.
That is it. Hope this help someone.
Andy
And what about the CID matching
Good for you! Tomorrow I´ll be picking up my 8525 and I´am anxious to unlock it and strat using it, in preparation I´ve been reading throughout the forum and looks for me that it was very simple for you (except for the issues caused by Vista). I was wondering if you had to check the CID in your device or if you just went blind into the procedure regardless the CID inconveniences?
Why don't 8525 users simply call cingular for the subsidy unlock code? Its cleaner, faster, and there is no risk to brick'ing your phone.
I really don't get it.
Just followed your steps and it worked for me as well. The first time I ran MaUpgradeUt_noID it failed with a 112 country code. But like you said, run it the second time and it worked.
Just popped my tmobile sim in and am going to install blackberry connect because that sim has by BES enabled and see what happens
Thanks much!!
wimpy said:
Why don't 8525 users simply call cingular for the subsidy unlock code? Its cleaner, faster, and there is no risk to brick'ing your phone.
I really don't get it.
Click to expand...
Click to collapse
I asked the rep in the cingular store, they lie to me, telling me just call the 611 customer support number and they will unlock me. So, it is a company phone and I said fine.
I have been cingular for years and I will definitely switch to TMOBILE once this expire! I had tmobile before and they just require me to be with them for 90 days before I call.
About the 611 call, they ask me to join the $6.99/mo global travelling plan.
MacGuruTX said:
Just followed your steps and it worked for me as well. The first time I ran MaUpgradeUt_noID it failed with a 112 country code. But like you said, run it the second time and it worked.
Just popped my tmobile sim in and am going to install blackberry connect because that sim has by BES enabled and see what happens
Thanks much!!
Click to expand...
Click to collapse
I have SIM from all the places I have been to and once a non-singular SIM inserted into the phone, there is a pop-up a screen asking for UNLOCK CODE.
andykwg said:
I asked the rep in the cingular store, they lie to me, telling me just call the 611 customer support number and they will unlock me. So, it is a company phone and I said fine.
I have been cingular for years and I will definitely switch to TMOBILE once this expire! I had tmobile before and they just require me to be with them for 90 days before I call.
About the 611 call, they ask me to join the $6.99/mo global travelling plan.
Click to expand...
Click to collapse
All you have to say is you're travelling outside the United States and wish to use the phone with a different sim. They will do it right there and then, or they will log a ticket to have some other group do it. It can be had instantly, just a matter of whether the rep you talk to have access to that system. The unlock code is based off of your IMEI number.
I think there is a number in the wiki page that connects you directly to their roaming group of some sort. I just dialed 611 and they emailed it to me the next day without any additional plan.
You'll simply roam on other carrier if cingular network isn't found.
wimpy said:
All you have to say is you're travelling outside the United States and wish to use the phone with a different sim. They will do it right there and then, or they will log a ticket to have some other group do it. It can be had instantly, just a matter of whether the rep you talk to have access to that system. The unlock code is based off of your IMEI number.
I think there is a number in the wiki page that connects you directly to their roaming group of some sort. I just dialed 611 and they emailed it to me the next day without any additional plan.
You'll simply roam on other carrier if cingular network isn't found.
Click to expand...
Click to collapse
That is what exactly I said.... I have 3 other phones with Cingular before and they all unlocked the same way. I think they just mess up on this one this time.
hey ya'll, so I followed these steps and everything works except for now, the backlight on the slideout keyboard no longer turns on -- any suggestions on what to do now?
no cingular unlock code can SuperCID your 8525 however...
I worked for me
andykwg : Thank You!
Having your post as a starting point and after a lot of reading through out the threads I suceed to unlock my 8525 spl 1.06.
I found a couple of issues during the unlock
1.- After 2% progress I got an Error # 262 (Update Error) so I had to get into the recovery procedure, but it was very easy and finally I downgraded to ROM 1.30.502.1
2.- During the Radio Patch flash I got the Error # 120 (Country Error), but as you instructed I only had to rerun the exe and at the end I got the expected Error # 114
Thnk you and pof, I guess I wouldn´t dare if I had read your post.....
I see that you can't do this in VISTA.
Has anyone tried in Windows XP x64 yet?
Thanks,
-J
RUU.dll error when I run MaUpgradeUt_noID.exe
So I downgraded from SPL 1.06 to SPL 1.04
I syched.
I tried to run MaUpgradeUt_noID.exe and I get this error:
"This application has failed to start because RUU.dll was not found. Re-intalling the application may fix this problem.
I searched the threads looking for this error with no luck. What am I doing wrong?
Thanks,
8525 owner running XP Pro
wimpy said:
Why don't 8525 users simply call cingular for the subsidy unlock code? Its cleaner, faster, and there is no risk to brick'ing your phone.
I really don't get it.
Click to expand...
Click to collapse
I don't think You get SuperCID that way do you?
8525 owner said:
So I downgraded from SPL 1.06 to SPL 1.04
I syched.
I tried to run MaUpgradeUt_noID.exe and I get this error:
"This application has failed to start because RUU.dll was not found. Re-intalling the application may fix this problem.
I searched the threads looking for this error with no luck. What am I doing wrong?
Thanks,
8525 owner running XP Pro
Click to expand...
Click to collapse
SAME here... Please HELP ASAP!
For those with errors please ensure your rom firmware and you follow the steps to the letter.
I love my 8525 i just wish they gave a cover, it gets messy on the screen.
Worked for me as well.
Thanks! Followed your instructions to the letter, now mine is unlocked and superCID! No issues and running T-Mobile now.
country code error, what next?
Need a bit of help here. I downgrade successfully my 8525 from 1.06-->1.04 but when i tried to run the map****.ID.exe i continue to get country code error 120.
I must have done this at least three time and still no luck, what next can i try?
DishXpert
dishxpert said:
Need a bit of help here. I downgrade successfully my 8525 from 1.06-->1.04 but when i tried to run the map****.ID.exe i continue to get country code error 120.
I must have done this at least three time and still no luck, what next can i try?
DishXpert
Click to expand...
Click to collapse
You are not SuperCID.
Run the new Pof unlocker/SUPERCID version 3.
Related
Hi,
I recently had a power cut (yes, a lights off power cut!) that killed my PC half wat through installing the Cingular English CWS__001 1.34.502.1 09/21/06 ?? 1.16.00.00 32.53.7018.01H 14955.2.3.0 ROM onto my SPV 3100.
Now SPV 3100 will boot to the ROM I was running prior to the upgrade but I can't use the telephone. I'm also not able to rerun the upgrade as it got far enough through the process to upgrade my bootloader to 1.06 - therefor rendering me unable to load another ROM.
Before the crash I was using the Imate ROM as below and M3100 was sim unlocked and running on o2 3G
i-mate English CDL__001 1.20.305.3 07/21/06 1.20.305.104 1.07.03.10 32.41.7010.02H 14955.2.3.0 1.04
Please help.
Thanks
If your device is still working ok as a PDA then hopefully it just screwed up the radio update of your device.
Try reflashing the Radio only
Look Here
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Post back with results
Regards
S.K
EDIT: Sorry only works on 1.04 bootloader only. Afraid your gonna have to wait for Pof to come up with a 1.06-1.04 workaround
Hi S.K,
Thanks for the info. I have now tried installing the HERM_1.20.31.10_type2_radio_fixed upgrade but unfortunately the radio upgarde crashes also. It all seams to go well, (after using MaUpgradeUt_noID.exe twice) the phone says "Upgrade Radio Stack Please wait" and the progress bar appears on the PC but then after 10 mins I get an ERROR 114: RADIO ROM UPDATE ERROR.
Do you think this might be becuase the last upgarde partly installed bootloader 1.06?
Any other suggestions - I'm desperate to get the hpone on M3100 working again.
Thanks
Read here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Please post USB monitor capture, otherwise can't help u.
Hi Pof,
Thanks for the offer, I will sort out the usb software on Monday. Are there specific actions that I should try, obvioosly I will usb monior everthing I do but I want to keep it to the point and not waist yr time trailing through huge log files.
Cheers
BTW - I have tried all options of recovery, such as attempting to install the latest radio and trying to install the new rom from an sd card, trying several roms and using imei unlocker - all without any joy.
I think the problem is that I have partially installed radio and bootloader 1.06 so I can't fix the problem.
Thanks again.
@wotthefok:
For me is faster to look at the usb log file, then I exactly know why the upgrade fails, otherwise I have to decode it from your feedback and I can't be really sure. Check the "upgrading problems" page on the wiki, if none of the steps there seems to fix your problem, post USB monitor log please.
Log Files as requested
Hi,
I have captured information using usb monitor and attached the zipped log files for your attention.
The first is called USB_monitor_log_Herm_120Radio_twice. This log details attempting to install the HERM_1.20.31.10_type2_radio_fixed upgrade, and running it twice - just in case.
The USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_twice.zip details attempting to install the RUU_HER_Cingular_1.34.502.1_1.16.00.00_wwe_cws_ship upgrade, simply using the standard ROMUpgradeUt.exe method. This generates the expected Vendor ID error.
My primary focus is to install the radio upgare or download my bootloader to 1.04. The PDA part of my m3100 does now freeze occasionally but at least functions whereas the phone is completely dead.
Thanks in advance.
Please attach capture in *ANSI TEXT FORMAT*, the .lgs file you zipped is totally unuseful
Edit -> Export and Save as type "ANSI Text files".
Also make sure you export in "COMPLETE" view, see the wiki for more details.
OK, Spot the novice.... I have now created a txt log file that captures activity of me running the 120 Radio upgarde - but only once this time. I still had to zip the file due to it's size. Hope this is OK.
I'll send the other logs within the next couple of hours. Please let me know if the output I have sent so far is acceptable?
Thanks
wotthefok said:
Please let me know if the output I have sent so far is acceptable?
Click to expand...
Click to collapse
No, it's a "basic" capture, you have to export a "complete" capture:
Start USBMonitor.
File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
In the upper part there are two tabs: basic and complete. Click on "Complete".
Right, Try again (duh!) OK, I've tried to keep the log files names as self-explanitory as possible... USB_monitor_log_Herm_120Radio_run1.zip is the r20 radio upgrade, 1st run and USB_monitor_log_Herm_120Radio_run2.zip the second run - without disconneting or resetting the device.
USB_monitor_log_runing_Cingular_1.34.502_11_uprgrade_ran_twice.zip is the Cingular upgrade run via the ROMUpgradeUt.exe, again run twice without disconneting the device.
Hope I got it right this time.....Please let me know if there is anything else I can do.
Thanks.
This time you got the captures right
- You're on bootloader 1.06: You don't have 'rtask' command, you won't be able to do any radio upgrade only.
- Your device is not CID unlocked (Security level=FF, unprivileged)
- The bad flash caused the CID area to corrupt (CID: Wait interpreter timeout)
- When flashing a full ROM you get a CID not allow (255) this is because your corrupted CID doesn't match the CID on the ROM.
The radio part is screwed, you could have fixed this if you where in bootloader 1.04 by flashing a full ROM, but as you are in 1.06 you can't because of CID checking. But you're lucky because the OS ROM is intact and you can boot the OS, you should be able to downgrade to bootloader 1.04 from OS and flash a full ROM after, which will hopefully fix your radio.
Just wait until a solution to downgrade bootloader is available (I'm working on it).
Hi,
As I suspected.... Suppose it's not all bad news though - just means that I have to be patient and use my communicator once more. Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
I have already got a IMEI-CHECK sim unlock from where I originally got the M3100 unlocked from Orange to work on o2. That said, I have run either unlocker 2 or 3 with the .unl that I know worked I now get
HTC HERMES v3c unlock
Starting communication.........
Checking device..............ERROR
The device you try to unlock is not supported.
Please contact your supplier site.
Device is rebooting
Press any key to quit this application.
I'm currently chatting to the guys at IMEI-CHECK re this problem.
Anything else I can do to assist you in anyway??
Cheers
wotthefok said:
Do you know if the guys at IMEI-CHECK have a downgrade solution? Even if it's a pay for option??
Click to expand...
Click to collapse
They have it (M3100v3cUnlock.exe), but it will not work on your device because your IMEI is corrupted and their unlocker will not be able to read it and to check/compare with the .unl key file.
Hi,
Just a quick update. The guys at MIGsofT LTD have VERY VERY generously said they'll have a look at the problem for me so my phone will be winging it's way to them today.
Thanks for your assistance and helping me be certain of the problem and to better understand the root cause.
Hope this information will prove useful to others.
Another quick update...
The guys at IMEI-CHECK (MIGsofT LTD) have rectified problems with my handset and managing to reinstall bootloader 1.04 in the process!!
They also turned my phone around in under three days and only charged me the cost of postage! I had previously been a customer of theirs but it was still a very generous and helpful offer and I would certainly pay for the service than have a duff handset - after all £250 + for a paperweight is rather excessive....
If you're experiencing a problem like mine why not get in touch with them and offer them money to have a look at your handset? No Guarantees but it seemed like my last chance, for a while anyway.
Praise to IMEI-CHECK for a brilliant service - they are King of the day !!
Hi guys,
Upgraded to 1.16 radio - (Tmobile UK ROM)
This kept 'hanging' so upgraded to 1.20 - this failed
Left with NO GSM - followed steps as requested set pass etc.
Still wouldn't upgrade
Tried to put latest ROM on (South african?) this FAILED but installed boot load 1.09 - argh!
BOUGHT (£20) the imei-check to downgrade - this WONT WORK - keep failing!!
Please help - stuck now - phone boots - but has NO GSM all the time...
Please help!!
please attach a usb monitor capture of a full rom upgrade until it fails. Probably will be "cid not allow (255)", but just to make sure.
No T-MOB001 rom exists yet
Did that - thats exactly where it failed!
Is it stuffed? :-(
I don't know, never had one of those with "NO GSM" error on my hands.
Probably as radio is screwed CID is corrupted and you'll not be able to flash a ROM even with your original CID. I think for you the best would be to send it to service centre.
Yeh, thought it may be stuffed! FUnny thing is, when I do a hard reset, it doesn't have the NO GSM, it reports 1.16.0.0, it's as if the T-Mobile customs reset it all. Is there any way of stopping the customs?
Regardless, I have had the phone < a month so I'm ringing customer services to see what they can do - maybe not admit I've tried to upgrade it just yet!!!
roger said:
Is there any way of stopping the customs?
Click to expand...
Click to collapse
I guess by "customs" you mean the Extended Rom, if yes, just do a soft reset before it installs (3 seconds). But I don't think it would do any difference...
Ok- update to problem,
Managed to downgrade from 1.09 to 1.04 of bootloader usining IMEI-CHECK.
Did HARD RESET and plugged in hermes when "press screen to continue" came up (just booted) linked to ACTIVESYNC then ran the software IMEI-CHECK sent me, this connected to hermes and asked for .unl file from imei-check. This 'downgraded' to 1.04 of bootloader.
Then managed to install a 1.13 radio rom - hermes still kept hanging -but I could use phone a little (managed to make 2 calls before a lock up). I was going to re-install another full rom upgrade - I think this may have sorted it, but by this time I had rung T-Mobile support in UK and they agreed to replace unit (I pretended it had gone wrong 'all on its own' hope Karma doesn't catch up with me!)
I THINK I would have managed to sort this using the solution from IMEI-CHECK and this forum by reapplying another full ROM upgrade. So thanks to everyone for their help! Hope this is of some use to someone!
Hello all,
I Eb'd an HTC wizard (cingular 8125) running Wizard Love/NBD WM 6.
On the load screen I get:
AKU 2.3;
IPL and SPL:2.25.0001;
radio:2.25.11;
rom: 6.0.0.0.
My carrier is Tmobile.
Question 1: If my phone has this newer ROM and it takes calls on the Tmobile network it has been CID unlocked and SIM unlocked...right?
I wanna update my rom and think that I am competent enough to do so but there is alot to learn and this is not my full time gig...right.
Question 2: So, if I am correct in Q1 I should be able to flash roms right?
However when I attempt to do so the RUU gives me [error 224]. Active sync and or WMDC says its connected. (I installed the AS drivers in WMDC)
Question 3: Where do I go from here?
Question 4: The wi-fi is currently not working will a new rom potentially clear this up?
Thanks in advance for the time and advice..
grazie
hmmmm,
Well,did you updated to NBD wm6 yourself ? and how did you updated ? which method you adopted ? SoftSPL or HardSPL ?
You say its SIM unlocked as it takes calls on the Tmobile network .Did you SIM unlocked with lokiwiz03a ?
yes ! a G4 can be SIM unlocked but it can not be CID unlocked,however,it can be upgraded to wm6 rom,but with method either 'SoftSPL' or 'HardSPL'.With your present ipl/spl 2.25.0001 and you say its NBD wm6 running,then it must have been upgraded through 'SoftSPL' method,as it uses patched ipl/spl and Cid unlocks the phone temporarily,but it never permanently CID unlocks the phone.But with 'HardSPL' ,it changes the ipl/spl to a patched ipl 2.21.0001 and spl 2.21 olip.So everytime you want to upgrade,you'll have to upgrade using 'SoftSPL' method.
could you elaborate a little more about this.
Cheers!
Hey thanks for the correspondence zabardast_1, I have been getting frustrated and I have many times contemplated going for the brick or bust approach here.
So, I have done none of the updating on this rig. I rec'd it and I wanted it primarily for wifi however I can't get the wifi card/ (sdiowlan I believe) to even recognize an AP (... I posted in the networking forum but no response.) Thus my own reasoning leads me to believe I should start from scratch with a new rom unless you know of something else.
So, I am not the most savvy and thought that all of the info I had led to SIM and CID unlocked. I just read otherwise last night and in your reply. The info I have provided is accurate the IPL, SPL, radio, although I don't know which NBD release it is; just says 6.0.0.0 and release date: 2/2/07.
I am trying to get the new rom on the my device however and I would've probably already bricked it if I could get an RUU to communicate with my wiz. I always get [Error 224] when I run it and my phone is connected through active sync. I am running vista but have installed the AS drivers for WMDC. I also tried it at work the other day with XP same situ. I then tried flashing from the bootloader screen with an NBD, Wizard Love ( w/ Italian installer?), and T-mob (226102_22610105_022511). The only one that says it will update is the Tmob ROM, however I got cold feet at the update button and canceled.
Other funny stuff I have observed that may or may not be related to the problems I am having are:
Can't install cab files ie (enable rapi or Cert SPCS) and Wiz Sys Tools couldn't read my CID block and hard_SPL G4 gives me REXX error ( SPL_Version has no value).
So, any wizdom you or anybody can drop is much appreciated and needed at this point.
Whew...
Listen carefully. G4 Wizard cannot be CID-unlocked without paying money. (And yes, you are using a G4).
What you need now is to Flash your original stock carrier ROM (Or wizard love) to get your OS back. Then either use SoftSPL or install HardSPL and flash WM6 ROM.
Thanks Starkwong,
I will try installing wizard love tomorrow at work and if that don't work I will attempt a Cing ROM (will all of these work or do I need to mind my G3's and G4's for these???)
Grazie
So, It worked using Wizard Love at work and out of the bootloader window. Now I need to:
1.) Get wifi working.
2.) Get a newer ROM
I put a post up in the networking thread, I am a tool so far as these devices are concerned so be easy on me.
http://forum.xda-developers.com/showthread.php?t=372811
So do I get the wifi issue resolved before I reflash???
Thx again
I don't know what you mean by "wifi not working".
Maybe it is the wifi AP doesn't allow 11Mbps (802.11b) connections?
However, going to any of the WM6 ROMs should already set the registry to allow Wizard connects to G-Only APs. Just use HardSPL/SoftSPL and flash a WM6 and you will see.
OK so "wifi not working" may indeed be a general statement...
What I mean to say is that I am not able to connect to any wireless networks for internet not home (Linksys WRT 54G v5 with ddwrt firmware) or school (university wide) or my city's wifi network. It won't even detect them at least none that Ive seen since I've rec'd this phone. So, that is what I meant by the ambiguous statement.
So, being as your last post was a success I will try as you say and post the results tomorrow. Thanks again starkwong!!!
1 quick thing however, to be sure, I can now try the hard spl or soft spl method of tricking my phone to run an upgrade to WM6?
Still not able to get wifi APs????
OK although I have been successful at reinstalling the Mfg ROM and then Hard SPL'ing my wizard thanks to ya'll I still am unable to connect to a wireless network (see one even). I have the Olip on my SPL and I installed a TNT version of WM6 and I am still at work (drunk but still here). Anyway I can't see my wireless AP and I am beginning to think its a hardware issue if thats possible, i dunno the dynamics of this system maybe thats why it was for sale. In any event as usual I am willing to try what ever you guys throw at me as you're my only hope obi wan. Alright Im gonna go home for the night and try getting on to my home network.
Thanks again for all the help guys.
Is your device a original one from phone operator? I suspect your device is a China Dopod 838 with replaced casing, because the China version has the wifi hardware removed, so wifi can't be started even if an English ROM is used.
Looks to be authentic 8125
Starkwong, the Cingular logo and the 8125 model # are on the phone case where they have been when I've seen them before in pics. Therfore, I dunno I guess it looks like every other 8125 I've seen. Can I check the SN, IME or anything to be sure?
Thanks Again!!!
Starkwong,
I am getting all the options for wifi on my phone the LHS LED flashes green when I enable it and alternates blue green when BT is enabled. So, could it still be that its a dupod? I dunno but I am going home for the night... Thanks for your help. I will try connecting to my home network when I get there.
I must be thick as I have read more posts on this than I have had hot dinners and tried various utilities all to no avail although thankfully my Wizard still seems to work.
My O2 XDA-Mini s is about 2 years old and of course locked to O2 although the device come up as SIM Unlocked but CID Locked.
IPL - 2.21.0001
SPL - 2.21.0001
I am now on the Three network and would just like to get back to using the phone I love rather than the freebie I have now, so I am assuming I need to get CID Unlocked?
Having bothered to get to that stage I would want to scrap the O2 software and upgrade to a better ROM.
Sorry for being so stupid on this, I am hoping someone in the know can take the time to reply.
Thanks in advance
If it's sim unlocked you don't need to CID unlock to enable other sims.
If your new sim is rejected, then the device is still sim locked.
CID is only used for flashing, so if you want to upgrade to the better WM6 roms now available, you'd have to unlock it permanently (hard SPL) or use the Soft SPL.
Good luck,
EquinoXe
the-equinoxe said:
If it's sim unlocked you don't need to CID unlock to enable other sims.
If your new sim is rejected, then the device is still sim locked.
EquinoXe
Click to expand...
Click to collapse
Thanks for taking time to reply EquinoXe, you have confirmed what I had already thought.
The device reports "Invalid or missing SIM card" with the Three SIM card and WST v4.2.2 reports "Your phone is already SIM unlocked" ??
I do wan't to upgrade the ROM but more importantly I want to get the thing working with the Three SIM card, then I can worry about the ROM.
Any other suggestions will be gladly received.
Thanks in Advance
Download and use the LOLKWIZ03b program from these forums, follow the insturctions EXACTLY, and it will generate you a SIM unlock code.....enjoy!
ashasaur said:
Download and use the LOLKWIZ03b program from these forums, follow the insturctions EXACTLY, and it will generate you a SIM unlock code.....enjoy!
Click to expand...
Click to collapse
I have done this twice just recently but my G4 is not asking me to enter any unlock code. I read other threads where people had similar problems so tried a few times, device still comes up "Invalid or missing SIM card"
I ran EnableRapi from the device before running the batch file so I'm not sure what is going on or if it is something quirky about the G4 device??
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\Jackson>cd\
C:\>lokiwizmsl
machinagod's HTC Wizard/Prophet/Charmer MSL Revealer v0.3
NOW WITHOUT CID Unlocking POWER!
ECHO is off.
Supports SPL 2.x!!
--------------------
WARNING: This tool is highly experimental!
I will NOT be held responsible for any problems caused by this tool.
--------------------
Thanks to xda-developers, spv-developers, and especially itsme by the work they
released. This solution would not be possible without them.
--------------------
Unlocking RAPI Please wait...
MachinaGod RapiUnlocker v1.0
Initializing.......................Done!
RAPI Unlocked.
Starting MSL work... DO NOT DISCONNECT UNTIL THIS SCRIPT ENDS
ECHO is off.
CopyTFFSToFile(0x0, 0x10000, lock_backup.bin)
ECHO is off.
ECHO is off.
SIMLock Code is your code... Type it with another SIM in...
--------------------
Lock Status: 0000000000000000
SIMLock Code: ¨~äe├ÇÔ►-┴«p¦╚.;
This exe file was created with the evaluation version of Perl2Exe.
For more information visit http://www.indigostar.com
(The full version does not display this message with a 2 second delay.)
...
--------------------
"Standing on the shoulder of giants"
Ricardo Afonso, 2005
Press Any key to Exit.
Strange, according to lokiwiz (and WST) you are sim- unlocked.
But clearly your three sim card won't be accepted.
I do remember that HTC had been messing with the bootloaders, had to downgrade one in order to unlock it too..
Could you Flash a 2.19.0001 (or earlier G4) IPL/SPL ROM and try again?
You can use dharvey4651's thread as a guide to flash the IPL/SPL.
Just ignore the carrier ROMs, and only update (downgrade) the IPL/SPL with one attached to djharvey's thread (preferably the orange, because that one worked for me).
Flashing bootloaders can damage your device beyond repair, please use this method only if you are shure about the process, and know what you are doing. I am not responseble or liable for any damages.
Flash the IPL/SPL (takes a minute), then try again to unlock the phone.
Note: WM6.x needs IPL/SPL 2.19.xxxxx at least (works great with a 2.19), so if you have downgraded to a lower number, you'd have to upgrade again in order to run WM6.x .
Good luck,
EquinoXe
Same Problem
I have the same problem as the previous post. I downgraded from WM6.1 to a WM5.1 ROM and then ran lokiwiz - success!
I have now gone back to the original WM6.1 ROM and again I am locked out from my o2 SIM.
I am using: WM6.1 ROM Prophet My Green Edition http://forum.xda-developers.com/showthread.php?p=2116170
Any suggestions?
IPL 2.10.001
SPL 2.G4.4PDA
GSM 02.47.21
OS 5.2.19.209
the-equinoxe said:
Could you Flash a 2.19.0001 (or earlier G4) IPL/SPL ROM and try again?
You can use dharvey4651's thread as a guide to flash the IPL/SPL.
EquinoXe
Click to expand...
Click to collapse
Thanks EquinoXe, I am going to try a T-Mobile, Vodaphone and Orange SIM later to see what results then maybe tomorrow try your last suggestion.
Thanks and I will post any results, hopefully not a flashy paperweight (~:
------------------------------
I have now tried T-Mobile, Vodaphone and Orange SIM cards in the Wizard and all work OK so unlocking was never the problem, obviously O2 is OK also as this was it's original branding.
So the problem is only with the Three SIM, I have an old T610 and T630 which I just put the Three SIM into with the same results.
Need to do a bit more reading on this but I thought this sort of restrictive trading practice went out with the monopolies issues, as it seems at the end of my contract it's not just a matter of me buying a phone of my choice, if I want a new handset I have to go with Three, who interestingly don't do XDA style phones, or change contracts.
More if it happens.
I'm guessing that the reason the 3 sim card won't work is because the Mini S isn't a 3G capable device - 3 is the only network in the UK that's 3G exclusive, hense why other (T-mobile, Vodafone, O2 and Orange) sims will work and the 3 sim card won't.
Hope this helps.
Right chaps... so, here's the deal, I've done a SIM unlocker for the Sedna, if you want your device sorted, click this link:
http://sedna.htc-unlocks.com
Now... this also contains Hard-SPL; if you *DON'T* need a sim unlock, then just wait as I will be releasing the Hard-SPL here anyway.
if you do need a simunlock, use the link.
Good stuff!
we are receiving P6500 next week
When you say it's for Sedna,do you mean p6500 or p6550? Some call the
P6500 the 'Sirius' so I just want to check first. I have a P6500.
M.S
Same thing (well, as far as this is concerned anyway)
Right, so does this thing invalidate one's warranty?
that depends really... mainly on how badly you break the device.
if you don't break it badly enough to stop you from overwriting the Hard-SPL manually then you just replace it before RMA.
if you can't do that, it's unlikely they'll be able to discern you Hard-SPLd it
Does the SIM unlock still work if you overwrite the Hard-SPL?
Does the very fact of unlocking with this program affect the warranty?
yes, it works indefinitely no matter what you do.
and I already answered the warranty question.
go look up the term "warranty by law" and "warranty by manufacturer"
How much time to obtain the Unlocker?
Naturally, I paid ...
My p6500 now unlocked.
Just to say thanks, this has worked and I've now unlocked / debranded my orange p6500!
Many thanks.
Richard
@OliPro
Will you publish SSPL and HardSPL for SEDNA please?
Unlock
The unlocker has not worked on my Orange P6500
I have tried it twice without success.
i keep getting the message 'network locked' when I put a t-mobile simcard in to the device
Mysterious Stranger said:
Just to say thanks, this has worked and I've now unlocked / debranded my orange p6500!
Many thanks.
Richard
Click to expand...
Click to collapse
jonboy8841 said:
The unlocker has not worked on my Orange P6500
I have tried it twice without success.
i keep getting the message 'network locked' when I put a t-mobile simcard in to the device
Click to expand...
Click to collapse
drop me a message then and we'll see what's not working.
I've not yet encountered one that's worked because of the device; it's always been due to the user.
@Olipro/others:
I can buy the Spanish ROM P6500 from Expansys USA for about $100 less than the WWE ROM (EU) version...
Any reason whatsoever to NOT do this???
Thanks and best regards...
EDIT: Of course I would want to flash WWE ROM to it as my Spanish is a little rusty
nope, save the money and get the cheaper.
Which reminds me, I really should get around to Posting Hard-SPL at some point today.
Olipro said:
I've not yet encountered one that's worked because of the device; it's always been due to the user.
Click to expand...
Click to collapse
Au contraire. I can forward the PM's back to you if your memory is that short
Sorted in the end though. No, it wasn't my fault!
M.S
OliPro, Tnx for unlocker and fast replay ... tested with success on Orange P6500 ...
Thanks Olipro, followed your advice and it worked perfectly, i now have an unlocked and debranded p6500 for about 25% of the price orange charged
IT's not working for me
The hard SPL runs and clearly flashes the handset as it's then has the OliPro rom boot image when it goesto update the radio rom it then tells me it's 100% complete then says it's failed to flash the rom propperly and returns the phone to the coloured bars meaning i have to reflash the entire thing with an original rom to make the hand set work.
ANy help would be appreciated, it's a second gen orange 6500 if that helps which may mean they've mucked around with the network lock when they dropped the 6.1 release.
Hi,
Was the HardSPL ever released for this handset?