is there anyway to unbrick a G4 wizard?
There are many ways.
But please tell us more about symptoms ?
Bricked how ?
What is on screen ?
i was just asking just incase i brick my phone.
when it is 'bricked', there is no way. It is like, when a person is 'dead' there is no way of reviving him/her. 'Bricked' is a terminal word, it may goes deeper as the gurus here find deeper ways to revive a unit.
hanmin said:
It is like, when a person is 'dead' there is no way of reviving him/her.
Click to expand...
Click to collapse
Jesus might beg to differ... but I ain't arguing!
BOWLOFO:
If you read the sticky thread at top of this forum, you will see how to remove the bootloader from a ROM before you load it.
This means that if a upload goes wrong and you can't get it load normally (eg it might LOOK "bricked"), you can always initialise the loader, an bring it back to life again! (eg it wasn't "bricked" after all.).
"Bricked" literally means = turned into a brick = useful only as a paperweight!
I guess some cases that look like they are "bricked", are actually just a case of needing greater skill to bring alive again.
If you are careful to follow ALL the instructions in that thread, then you should be OK, as there should always be a way to bring it back to life from any "brick-esque" situations.
Is that what "resurrection" means.....
Mike
My Wizard is really DEAD now due to the my to power off during Rom upgrading. I did tried hard-reset but it's always display the bootloader screen without 3-color stripper, so it can't connect to ActiveSync.
Please help with your knowledge...
Thanks,
KC
KChauJen said:
My Wizard is really DEAD now due to the my to power off during Rom upgrading. I did tried hard-reset but it's always display the bootloader screen without 3-color stripper, so it can't connect to ActiveSync.
Please help with your knowledge...
Thanks,
KC
Click to expand...
Click to collapse
Find out how to enter to Wizard boot mode (Tri-color bootloader screen)
1.Turn your device off
2.Hold the Camera button in and push the power button for 2 seconds
...you should get the 3 color bar screen
3.Plug your usb cable in to the phone
Hope I can revive my device...
KC
This looks good to me.
BTW It seems like you can access the bootloader by different key combination + reset, if we except the CommManager + Voice Record + Reset combination wich is intended to make a full format of the user area.
So I'm used to make a Mail + Photo + Reset combination (keep Mail + Photo pushed until magic screen appears).
Once you're in bootloader mode (Rainbow screen), Activesync won't launch synchronisation as the device is no longer identified as a Pocket PC, better ready to be loaded with a new OS.
Oh one thing. If you're stucked somewhere in the boot process and want to revert to a stable version, make sure you use an official release.
It would be nonsense to try to revive a bad upgrade with another one...
Related
I installed somet languanges support pack into it from PC, everything went fine, the PC screen said, install sucessful,, and the machine prompted to reset, and then,,,its dead!!!
The Lobster only now shows the virgin mobile logo,,cant even switch off...
What should do............???
Thanks a million!!!!!!!!!
Lobster is dead? it should be cooked!
Is the Lobster/monet ROM floating around somewhere ?
dead lobby
You've probably either sorted this by now or binned the phone but I thought I'd post anyway as it may help others.
You don't describe what you mean by dead but have you tried hard reset?
WITH PHONE SWITCHED OFF (in your case remove and replace the battery)
1. Press and hold soft1 and soft2 keys (i.e. menu keys).
2. Press and hold power button for around 1 to 1.5 seconds. Release power button. Keep holding both soft keys.
3. After a while, black screen should show instructions asking user to press '0' key to reset to factory default.
4. Press '0' within the timeout period (which is very brief).
5. If instructions don't appear on the screen, repeat steps 1 to 4.
You have to flash it using it's original rom (for locked device).
but if you phone is CID UNLOCKED you can flash it using ROMIUPDATE. just put the phone in bootloader mode and run the RUU Update.
sk8erfrankrox said:
I installed somet languanges support pack into it from PC, everything went fine, the PC screen said, install sucessful,, and the machine prompted to reset, and then,,,its dead!!!
The Lobster only now shows the virgin mobile logo,,cant even switch off...
What should do............???
Thanks a million!!!!!!!!!
Click to expand...
Click to collapse
ok take batty out put it back in press to menu bottons keep hold and press power botton when a sreen tells you to press 0 do so it will hard reset you lobster
dvaiyo said:
You have to flash it using it's original rom (for locked device).
but if you phone is CID UNLOCKED you can flash it using ROMIUPDATE. just put the phone in bootloader mode and run the RUU Update.
Click to expand...
Click to collapse
hi~dvaiyo,
I have find the RUU update for lobster700 long time.
can you show url to download it ?
thanks ~
There is no place to downloat it. You must import it from other device... mtty can do it..
ive got a back up what i got form Scoter Kitchen if you what it let me no these three files BDTL0_SCOTERMSFLSH50.bin BDK0_SCOTERUT.bin BDK1_SCOTERMSIPL.bin
dvaiyo said:
There is no place to downloat it. You must import it from other device... mtty can do it..
Click to expand...
Click to collapse
I think thats you right, then the question is when I want to write into with MTTY, with which soft do I draw ROM? Please share successful experience, thanks ~
MttY?its so easy?ehe
Hello folks. The friend of mine has screwed up his Lobster, and now he wants to take a dump from another one. The problem is, mtty says r2sd command is unknown... he tried to issue password command, but we don't know the peoper password.
Does anyone have the proper password for bootloader? Or better... does anyone have a rom dump? It'd be appreciated...
utak3r said:
Hello folks. The friend of mine has screwed up his Lobster, and now he wants to take a dump from another one. The problem is, mtty says r2sd command is unknown... he tried to issue password command, but we don't know the peoper password.
Does anyone have the proper password for bootloader? Or better... does anyone have a rom dump? It'd be appreciated...
Click to expand...
Click to collapse
you have to pay £20 to cid unlock his lobby go here http://www.imei-check.co.uk/lobsterunlock.php
tankoki said:
I think thats you right, then the question is when I want to write into with MTTY, with which soft do I draw ROM? Please share successful experience, thanks ~
Click to expand...
Click to collapse
Try this :
http://forum.xda-developers.com/showthread.php?p=2100727#post2100727
travis said:
You've probably either sorted this by now or binned the phone but I thought I'd post anyway as it may help others.
You don't describe what you mean by dead but have you tried hard reset?
WITH PHONE SWITCHED OFF (in your case remove and replace the battery)
1. Press and hold soft1 and soft2 keys (i.e. menu keys).
2. Press and hold power button for around 1 to 1.5 seconds. Release power button. Keep holding both soft keys.
3. After a while, black screen should show instructions asking user to press '0' key to reset to factory default.
4. Press '0' within the timeout period (which is very brief).
5. If instructions don't appear on the screen, repeat steps 1 to 4.
Click to expand...
Click to collapse
I just somewhat bricked my Lobster today after installing fonts and ce-star into my device. I was so scared I nearly crapped my pants.
I stumbled upon your detailed instructions and it saved my thing, thank you so much =]
utak3r said:
Hello folks. The friend of mine has screwed up his Lobster, and now he wants to take a dump from another one. The problem is, mtty says r2sd command is unknown... he tried to issue password command, but we don't know the peoper password.
Does anyone have the proper password for bootloader? Or better... does anyone have a rom dump? It'd be appreciated...
Click to expand...
Click to collapse
I've found this link...
ftp://koxoguest:[email protected]/sp/rom/Lobster_700_tv_os.rar
Its supposed to be the ROM for the lobster. I however cant get it to work as my lobster is stuck on a white screen during boot and cannot get into Activesync. Can anyone advise How i can get into Bootloader mode? I have tried holding Camera key but to no avail...
try taking out the battery, then heating the back of the phone for a while
I did that on my brother's phone(his Lobster "died" the same way) on a sunny day leaving it to heat up for about 30 minutes of sunshine
after that put the battery in and try booting again
OMG......
you can say it clearly
are you update the rom?
if so ,may be the word storage is broken
travis said:
You've probably either sorted this by now or binned the phone but I thought I'd post anyway as it may help others.
You don't describe what you mean by dead but have you tried hard reset?
WITH PHONE SWITCHED OFF (in your case remove and replace the battery)
1. Press and hold soft1 and soft2 keys (i.e. menu keys).
2. Press and hold power button for around 1 to 1.5 seconds. Release power button. Keep holding both soft keys.
3. After a while, black screen should show instructions asking user to press '0' key to reset to factory default.
4. Press '0' within the timeout period (which is very brief).
5. If instructions don't appear on the screen, repeat steps 1 to 4.
Click to expand...
Click to collapse
For me it's not working.....
Any Idas?
I have searched and searched these forums and have seen several other people with this problem but no solution. I have also looked through the wiki to no avail, so if someone can give me an answer I would really appreciate it.
I have been able to get into the bootloader screen (the r-g-b white stripes) however there is NO text (no serial, no usb) on the screen and it is not recognized by any pc. Can't get any response from mtty.exe because it can't see the USB port. Have tried on multiple PC's...
Is there another way to resurrect this athena or is it DOA?
Thanks,
-Alex-
Some pics of problem...
Blank bootloader...
Please help!
Did you try reflash by SDcard?
http://wiki.xda-developers.com/index.php?pagename=Athena_SD_Card_Flashing
jas_pik said:
Did you try reflash by SDcard?
http://wiki.xda-developers.com/index.php?pagename=Athena_SD_Card_Flashing
Click to expand...
Click to collapse
Yes...no joy.
Just stays on the tri-color screen with no indication that it is reading the card.
Thanks for the advice though!
Did you try resetting - camera button and reset button on the back (I think...) pressed together.
Forum search will tell you exactly...
ssutherland said:
Did you try resetting - camera button and reset button on the back (I think...) pressed together.
Forum search will tell you exactly...
Click to expand...
Click to collapse
Yes, tried the hard reset (camera + reset) the alternate reset (comm + camera + reset) and even the other reset (volume slider + camera + reset). And yes, I was pushing down firmly on the camera button.
Each reset brings me to the tri-color bootloader screen with NO text. No model number, no OS version, no "USB" / "Serial"....just the red-gree-blue-white stripes.
I have looked extensively at all the forums, used the google search for the site and combed the wiki with no luck.
So do you think it is a lost case?
-Alex-
Hello,
sorry for what's happening to you. Can you tell what led to this situation ? Were you trying to unlock your phone or just flashing a new rom ?
luthor_70 said:
Hello,
sorry for what's happening to you. Can you tell what led to this situation ? Were you trying to unlock your phone or just flashing a new rom ?
Click to expand...
Click to collapse
I was trying to load a new ROM but I assumed that I had to use the OliPro unlock first.
Got to the radio flash and that is where it crapped out.
Now that I have read a little more carefully it looks like I don't need to use the OliPro beyond the first step for the stateside unlocked 7501.
Thanks,
-Alex-
when your on bootloader ? does windows detect a usb generic device ?
Nope. Tried 3 different PCs. Shut down all the activesync processes. No luck. No detection that anything is cabled to the advantage.
I am thinking that it is warranty time.
Damn, I hate this....its just the principle of the thing...
-Alex-
bairda said:
Nope. Tried 3 different PCs. Shut down all the activesync processes. No luck. No detection that anything is cabled to the advantage.
I am thinking that it is warranty time.
Damn, I hate this....its just the principle of the thing...
-Alex-
Click to expand...
Click to collapse
Key rule to remember is to always make sure the Advantage is Fully charged. Try charinging it and reflashing it with the factory rom, located here. http://www.america.htc.com/download/RUU_Athena_HTC_US_2.19.453.4_105_1.47.51.00_Ship.exe. Keep us posted and let us know how it went
have you removed the sim and memory card
just checking basics
try that with a full charge and then enter bootloader and connect to usb
Thanks for all the help! I gave up and warrantied a new unit where I WAS successful in loading a new ROM.
I have learned several valuable lessons in the ROM upgrade process. This was on an advantage 7501, unlocked, USA version. I did the upgrade the process with the OliPro 3.0 unlocker, the PK Rom 3.0 and vista pro (32bit):
- Make sure that you have NOT customized your athena/advantage beyond the basic calibration and cut/paste walkthrough.
-Download ONLY THE MOST RECENT VERSION OF THE OLIPRO UNLOCKER. CHECK TWICE TO MAKE SURE THAT YOU HAVE THE LATEST.
-You MUST let step one of the Unlock complete. With the latest version this will make a bricked Advantage practically impossible.
-Go through step 2 & 3 even if you don't think you need this. It will upgrade the radio and give you peace of mind if you are updating to the PK rom.
-Don't panic if you complete step 1 and goof step 2/3. You can recover. But if you screw up the initial SPL unlock in step1...it is not going to be pretty.
Hope this helps!
Thanks for everyones advice!
-Alex-
Hi all
Thanks to an outdated link on some external website I updated my ROM with an older v4 raphael - and now I'm stuck at this "This concludes the beta test of this software release" screen.
I CANNOT get into bootloader either
I dont want to throw this phone away now !!!
I'd be eternally grateful to someone...ANYONE who can get me back into working mode ..
PLEASE HELP. I've been searching these forums for 20+ hours now without sleep - and found nothing to help me get the phone back to working state.
Try taking out the battery, SIM & SD card. Wiat a minute or so and put only the battery back in.
SIMULTANEOUSLY press volume down, center button and soft reset. CONTINUE to hold volume down and center button. You should get to the tri-color bootloader screen. If you do, you will be fine, just flash a new ROM from SD. If not...
BTW did you Hard SPL?
Doug M.
I just tried that
It comes back to the normal windows mobile screen (like it would if i did soft reset). I did run the hardSPL before doing this - and I did see the tricolor screen before i updated this ROM
I just cant figure out how to get to the tricolor
dwmackay said:
Try taking out the battery, SIM & SD card. Wiat a minute or so and put only the battery back in.
SIMULTANEOUSLY press volume down, center button and soft reset. CONTINUE to hold volume down and center button. You should get to the tri-color bootloader screen. If you do, you will be fine, just flash a new ROM from SD. If not...
BTW did you Hard SPL?
Doug M.
Click to expand...
Click to collapse
also make sure you press UP on the volume control this will hard rest you. You should be able to let it run and it will get to the calibration screen. Once there run a new ROM wrapper.exe and all should be ok. Had similar issues like this don't panic.
Ive tried every combination of button pressing.... it just resets back to the OS screen
Humour me for a moment ...
Pull out the battery, pull out the SIM, and pull out your SD Card if you have.
Put the battery back in and only hold the Volume Down button. Keep holding Volume Down and turn on the device.
If all is well, you should see the TriColor Bootloader screen with USB in the bottom white area. If so, connect you're USB cable to your pc & device.
Flash the HTC Stock ROM (http://forum.xda-developers.com/showthread.php?t=478657) for now just to get the device up and running.
Let me know how you make out.
Cheers,
Now that the real tech studs are here you are in good hands. Just try what they recommend exactly. This is an unforgiving process. You really need to do it precisely as recommended.
It definitely sounds like this is fixable. Once you get this fixed, keep flashing.
Best of luck.
Doug M.
Thanks everyone !!
I have managed to unbrick it, reflash it and upgrade to RC4 and have it working !!
I love this community
I'd get this answer to the FAQ
Everyone who tried to flash a ROM for the first time has been terrified from this exact consequence...
hilaireg, I'm feeling much more comfortable now, knowing you are part of this helpful and amazing forum.
Thank god you are happy, otherwise if I see someone stuck with this process it hurts me more than anyone else. Always do ROM upgrade as shown by MSKIP in the sticky thread for beginners. Cheers.
Glad it helped ... if it was my suggestion that got the OP going.
sakshamkatyal is correct, mskip did a fantastic job at documenting the process and what I suggested ultimately does come from that article.
In this situation, the important lesson to learn is not the recovery; it is to always research and read up on a ROM one is planning to use so as to ensure that it is a) the most current, b) from a trusted source, and c) supported on an ongoing basis by the chef who prepared it.
Cheers,
Hello ,
my HTC Touch pro was bricked few months ago
i installed WRONG hard spl
on pc it showed 100% Completed
but i couldnt start my phone
how can i fix this ?
if i use Hard Reset method, i doesnt work , i cant start my phone
have you tried installing a new SPL via storage card (rename spl file to RAPHIMG.NBH and place it on the storage card) and enter bootloader mode by holding the vol down button when powering on the device?
the problem is
i cant start bootloader
nothing is working
I think you got yourself a brick...
Does it at least vibrate?
Run SPLExploit!
Dude, i have the same problem with you too but its not my TouchPro but its my old school Dopod D810. I flashed custom rom (my home cook) but forgot to add sumthin and finally i learned somethin that i can ****up my phones LOL. Just like what i thought my phone wont start and it refuse to enter on Windows OS but atleast bootloader mode still accessible. Thanks God
I search for post how to recover bricked phone (ofcourse on trinity room) and found some tools call "SPLEXPLOIT" it runs on DOS Mode. This program can erase your nand memory which in this case you flashed the wrong SPL and will rebuilt some bad Nand memory too. Good tho
I finally can bring my dead dopod came to life (for almost 1 year i left it on garage) lol. Just asked cmonex! maybe he can help you...
If this tools works universal i'm sure it will worked on TP too! Just asked cmonex for more details...
Run SPLExploit (as Administrator) --> while Enter in Bootloade mode -->
Just make sure that USB Cable was recognized as "USB" on the bottom of the screen not "Serial"!
When its done ....
NOTE: "Dont Soft Reset the phone even when SPLExploit ask you to SR the devices" just go ahead straight away flashing new custom rom or anything you want
Goodluck!
The OP can't get into bootloader, because the bootloader is corrupted/dead. So that isn't going to work.
JTAG is the only way to fix it, and as far as I know, no one knows how to do it on a Raphael.
Maybe playing with BIOS ( if BIOS can be accessed ) might help.
But BIOS can really make ur brick a worse brick if done wrongly please ask for help from the senior most members on Raphael forums.
And request them don't order them.
And if nothing works * I love to say this line *
You Just got Yourself a New Shiny Fine Edged Black Clear 600 U.S. Dollars worth Of a BRICK ! Enjoy !
atjee said:
the problem is
i cant start bootloader
nothing is working
Click to expand...
Click to collapse
Do you tried to start bootloader manually?
You can do that, press and hold Vol down, then reset button (with stylus), release reset (keep vol down pressed) and when the multicolor screen appears then release vol down key
I hope this can help you?
iugalde said:
Do you tried to start bootloader manually?
You can do that, press and hold Vol down, then reset button (with stylus), release reset (keep vol down pressed) and when the multicolor screen appears then release vol down key
I hope this can help you?
Click to expand...
Click to collapse
That is the only way to go to bootloader but as Farmer Ted mentioned his phone ( including bootloader is dead ! )
So i don't think there is any way out for you except if any really senior members can help you with bios or pump in something which starts your bootloader !
atjee said:
Hello ,
my HTC Touch pro was bricked few months ago
i installed WRONG hard spl
on pc it showed 100% Completed
but i couldnt start my phone
how can i fix this ?
if i use Hard Reset method, i doesnt work , i cant start my phone
Click to expand...
Click to collapse
Dude, you might try to PM cmonex. I hear she can do miracles. You can check out this thread and see a miracle there. Who knows? See what can be done. This link will take you to her contact page: http://forum.xda-developers.com/member.php?u=322932. Best of luck to you my friend. Worst case scenario, sell it for parts. Several people around here are always looking to replace "stuff", including me .
the same problem
I did the same thing to my HTC Fuze aka rafael or touch pro, from some reason it was the same thing as diamond and i flashed wrong spl and completely bricked it, no bootloader no nothing. So i went to a service and they said it was a hardware problem so they had to send it somewhere else to be fixed. It took them 3 weeks to get the phone back, in not working condition saying that motherboard was dead. I guess thats what happens when you flash wrong stuff... Now i dont know what to do either. I would like to sell mine for parts if someone is interested or if someone know how to use jtag i would pay him to try to fix it...
First of all sorry for my english not good.
Start : with my HD2 have brick after task29 and not success to flash new ROM I'm take USB. cable out and try to open my HD2 in to boot loader by put volum down + power bottom but screen not show any image or 3 color my phone it only long vibration pull battery out waiting 30 minute and put battery in and try to open my phone to boot loader but is same only long vibration.
Now : can not do any think with it when try to plug power in my phone is auto startup and long vibration.
I'm search on google and in this forum not have some one face problem same as me please help me to fix this.
Any body please help me, I'm love it because now we can run both WM. and Android
Upppp waiting for your help
Did you try a long press of the reset-button?
You could try to put the original Stock Image from HTC onto the root-folder of your SD-Card, rename it to LEOIMG.nbh and Push Vol up + Vol down during start and follow the on-screen instructions if it works.
Otherwise use Search-Function in the forum.
ı have jtag HTC for samsung and HTC devices if u want send for repair to me..
www.sevgigsm.net/forum
admin..
I use ORT
Did you check to make sure your radio version was correct before flashing? This is probably the number one reason for bricking.
Check this thread it may help you if you did the flash properly:
http://forum.xda-developers.com/showthread.php?t=668347
i got same problem now...
no screen, no boot, vol down+ power oso same
no screen just a long vibration
anybody help?
I am using the correct radio so don't tell me I am using a wrong radio or something, I have been flashing for 4 months so I know EXACTLY how to flash.
now i can neither get into tri-color or hard reset so don't tell me to flash or smth like that, just tell me how to recover properly
Don't tell us to use search or something because seems like only 2 of us is encountering this problem in the internet
I'm exactly the same problem as TS coz it juz auto go vibrate when plug in battery
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
at the long vibrate, when i plug in to my pc, it will keep on got usb connected and disconnected sound
and dont know what device is connected as not shown in found new hardware and device manager
I also have been searching all possible keywords about what me and TS encountered but all linked to completely UNRELATED results(like search for long vibrations only link to people asking how to make vibration long and 1st result is this thread)
bountygiver said:
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
Click to expand...
Click to collapse
Silly question, but are you holding (and keep on holding) the Volume-Down button while you press the power button?
of course YES
i told you i have been flashing for so long
Leo from T-Mobile. Hi! I've got same problem. After flashing new (next) rom phone definetely died. Phohe is currently simfree and with HSPL. Only one reaction is short vibration after press power button. I searched everywhere. My phone has no bootloader but system see him as Qualcom CDMA Technologies MSM. Thats all, any ideas? Please and thanks for advice.
czaruch said:
Thats all, any ideas?
Click to expand...
Click to collapse
Yes, you flashed a non tmous stock rom that included a ..51.. radio and it destroyed your phone.
What rom? exact filename please.
thank you so much.
I bricked a Leo with the .51 radio. I think I read that is a European or otherwise foreign radio. Since your ROM has Euro in the name.......
czaruch said:
ROM_Leo_HTC_WWE_EastEurope_1-66.
Click to expand...
Click to collapse
The full filename for that rom is
RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Si gned_15.32.50.07U_2.07.51.22_2_Ship.exe
it comes with a version x.xx.51.x radio, and they do Not work on tmous (t mobile us) phones. They kill them
Your phone is dead, sorry. No known fix.
warranty or repair (or JTAG if you are brave and have the money)
a friend of mine bricked his phone. he then tried to microwave it, but that didn't work after that he took a power wire from an old computer, cut it and connected it directly to the phone's parts where the battery would go...this completely f-ed his phone up (he also used a lighter to fake a powersurge of the battery). Then he called htc and a few weeks later he got a new hd2!
GOOD LUCK
lol, he doesnt need to do any of that, its allready as dead as it can be. Loads of epople have had them replaced under warranty with this kind of brick. It wont start, so htc/tmo cant see that its been hacked.
Hi! I understand and realy sad. Somebody know where could I fix it in UK? And how much for this pleasure. Thanks.
i would contact htc, see what they have to say. (dont say you flashed it, it just stopped working")